diff mbox series

[v6,04/14] tty: serial: qcom-geni-serial: align #define values

Message ID 20221229155030.418800-5-brgl@bgdev.pl
State New
Headers show
Series serial: qcom-geni-serial: implement support for SE DMA | expand

Commit Message

Bartosz Golaszewski Dec. 29, 2022, 3:50 p.m. UTC
From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Keep the #define symbols aligned for better readability.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/tty/serial/qcom_geni_serial.c | 62 +++++++++++++--------------
 1 file changed, 31 insertions(+), 31 deletions(-)
diff mbox series

Patch

diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c
index 359d9f0ba6ee..a4a50f2a6554 100644
--- a/drivers/tty/serial/qcom_geni_serial.c
+++ b/drivers/tty/serial/qcom_geni_serial.c
@@ -39,57 +39,57 @@ 
 #define SE_UART_MANUAL_RFR		0x2ac
 
 /* SE_UART_TRANS_CFG */
-#define UART_TX_PAR_EN		BIT(0)
-#define UART_CTS_MASK		BIT(1)
+#define UART_TX_PAR_EN			BIT(0)
+#define UART_CTS_MASK			BIT(1)
 
 /* SE_UART_TX_STOP_BIT_LEN */
-#define TX_STOP_BIT_LEN_1	0
-#define TX_STOP_BIT_LEN_2	2
+#define TX_STOP_BIT_LEN_1		0
+#define TX_STOP_BIT_LEN_2		2
 
 /* SE_UART_RX_TRANS_CFG */
-#define UART_RX_PAR_EN		BIT(3)
+#define UART_RX_PAR_EN			BIT(3)
 
 /* SE_UART_RX_WORD_LEN */
-#define RX_WORD_LEN_MASK	GENMASK(9, 0)
+#define RX_WORD_LEN_MASK		GENMASK(9, 0)
 
 /* SE_UART_RX_STALE_CNT */
-#define RX_STALE_CNT		GENMASK(23, 0)
+#define RX_STALE_CNT			GENMASK(23, 0)
 
 /* SE_UART_TX_PARITY_CFG/RX_PARITY_CFG */
-#define PAR_CALC_EN		BIT(0)
-#define PAR_EVEN		0x00
-#define PAR_ODD			0x01
-#define PAR_SPACE		0x10
+#define PAR_CALC_EN			BIT(0)
+#define PAR_EVEN			0x00
+#define PAR_ODD				0x01
+#define PAR_SPACE			0x10
 
 /* SE_UART_MANUAL_RFR register fields */
-#define UART_MANUAL_RFR_EN	BIT(31)
-#define UART_RFR_NOT_READY	BIT(1)
-#define UART_RFR_READY		BIT(0)
+#define UART_MANUAL_RFR_EN		BIT(31)
+#define UART_RFR_NOT_READY		BIT(1)
+#define UART_RFR_READY			BIT(0)
 
 /* UART M_CMD OP codes */
-#define UART_START_TX		0x1
+#define UART_START_TX			0x1
 /* UART S_CMD OP codes */
-#define UART_START_READ		0x1
-
-#define UART_OVERSAMPLING	32
-#define STALE_TIMEOUT		16
-#define DEFAULT_BITS_PER_CHAR	10
-#define GENI_UART_CONS_PORTS	1
-#define GENI_UART_PORTS		3
-#define DEF_FIFO_DEPTH_WORDS	16
-#define DEF_TX_WM		2
-#define DEF_FIFO_WIDTH_BITS	32
-#define UART_RX_WM		2
+#define UART_START_READ			0x1
+
+#define UART_OVERSAMPLING		32
+#define STALE_TIMEOUT			16
+#define DEFAULT_BITS_PER_CHAR		10
+#define GENI_UART_CONS_PORTS		1
+#define GENI_UART_PORTS			3
+#define DEF_FIFO_DEPTH_WORDS		16
+#define DEF_TX_WM			2
+#define DEF_FIFO_WIDTH_BITS		32
+#define UART_RX_WM			2
 
 /* SE_UART_LOOPBACK_CFG */
-#define RX_TX_SORTED	BIT(0)
-#define CTS_RTS_SORTED	BIT(1)
-#define RX_TX_CTS_RTS_SORTED	(RX_TX_SORTED | CTS_RTS_SORTED)
+#define RX_TX_SORTED			BIT(0)
+#define CTS_RTS_SORTED			BIT(1)
+#define RX_TX_CTS_RTS_SORTED		(RX_TX_SORTED | CTS_RTS_SORTED)
 
 /* UART pin swap value */
-#define DEFAULT_IO_MACRO_IO0_IO1_MASK		GENMASK(3, 0)
+#define DEFAULT_IO_MACRO_IO0_IO1_MASK	GENMASK(3, 0)
 #define IO_MACRO_IO0_SEL		0x3
-#define DEFAULT_IO_MACRO_IO2_IO3_MASK		GENMASK(15, 4)
+#define DEFAULT_IO_MACRO_IO2_IO3_MASK	GENMASK(15, 4)
 #define IO_MACRO_IO2_IO3_SWAP		0x4640
 
 /* We always configure 4 bytes per FIFO word */