@@ -12086,6 +12086,13 @@ S: Maintained
F: Documentation/devicetree/bindings/pinctrl/loongson,ls2k-pinctrl.yaml
F: drivers/pinctrl/pinctrl-loongson2.c
+LOONGSON-2 SOC SERIES THERMAL DRIVER
+M: zhanghongchen <zhanghongchen@loongson.cn>
+M: Yinbo Zhu <zhuyinbo@loongson.cn>
+L: linux-pm@vger.kernel.org
+S: Maintained
+F: drivers/thermal/loongson2_thermal.c
+
LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
M: Sathya Prakash <sathya.prakash@broadcom.com>
M: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
@@ -508,4 +508,15 @@ config KHADAS_MCU_FAN_THERMAL
If you say yes here you get support for the FAN controlled
by the Microcontroller found on the Khadas VIM boards.
+config LOONGSON2_THERMAL
+ tristate "Loongson-2 SoC series thermal driver"
+ depends on LOONGARCH && OF
+ help
+ Support for Thermal driver found on Loongson-2 SoC series platforms.
+ The thermal driver realizes get_temp and set_trips function, which
+ are used to obtain the temperature of the current node and set the
+ temperature range to trigger the interrupt. When the input temperature
+ is higher than the high temperature threshold or lower than the low
+ temperature threshold, the interrupt will occur.
+
endif
@@ -62,3 +62,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL) += uniphier_thermal.o
obj-$(CONFIG_AMLOGIC_THERMAL) += amlogic_thermal.o
obj-$(CONFIG_SPRD_THERMAL) += sprd_thermal.o
obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL) += khadas_mcu_fan.o
+obj-$(CONFIG_LOONGSON2_THERMAL) += loongson2_thermal.o
new file mode 100644
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Author: zhanghongchen <zhanghongchen@loongson.cn>
+ * Yinbo Zhu <zhuyinbo@loongson.cn>
+ * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
+ */
+
+#include <linux/cpufreq.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_device.h>
+#include <linux/thermal.h>
+#include "thermal_hwmon.h"
+
+#define LOONGSON2_SOC_MAX_SENSOR_NUM 4
+
+#define LOONGSON2_TSENSOR_CTRL_HI 0x0
+#define LOONGSON2_TSENSOR_CTRL_LO 0x8
+#define LOONGSON2_TSENSOR_STATUS 0x10
+#define LOONGSON2_TSENSOR_OUT 0x14
+
+struct loongson2_thermal_data {
+ int id;
+ void __iomem *regs;
+};
+
+static int loongson2_thermal_set(struct loongson2_thermal_data *data,
+ int low, int high, bool enable)
+{
+ u64 reg_ctrl = 0;
+ int reg_off = data->id * 2;
+
+ if (low > high)
+ return -EINVAL;
+
+ low = max(low, -40);
+ high = min(high, 125);
+
+ low += 100;
+ high += 100;
+
+ reg_ctrl = low;
+ reg_ctrl |= enable ? 0x100 : 0;
+ writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
+
+ reg_ctrl = high;
+ reg_ctrl |= enable ? 0x100 : 0;
+ writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
+
+ return 0;
+}
+
+static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
+{
+ u32 reg_val;
+ struct loongson2_thermal_data *data = tz->devdata;
+
+ reg_val = readl(data->regs + LOONGSON2_TSENSOR_OUT);
+ *temp = ((reg_val & 0xff) - 100) * 1000;
+
+ return 0;
+}
+
+static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
+{
+ struct thermal_zone_device *tzd = dev;
+ struct loongson2_thermal_data *data = tzd->devdata;
+
+ /* clear interrupt */
+ writeb(0x3, data->regs + LOONGSON2_TSENSOR_STATUS);
+
+ thermal_zone_device_update(tzd, THERMAL_EVENT_UNSPECIFIED);
+
+ return IRQ_HANDLED;
+}
+
+static int loongson2_thermal_set_trips(struct thermal_zone_device *tz, int low, int high)
+{
+ struct loongson2_thermal_data *data = tz->devdata;
+
+ return loongson2_thermal_set(data, low/1000, high/1000, true);
+}
+
+static const struct thermal_zone_device_ops loongson2_of_thermal_ops = {
+ .get_temp = loongson2_thermal_get_temp,
+ .set_trips = loongson2_thermal_set_trips,
+};
+
+static int loongson2_thermal_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct loongson2_thermal_data *data;
+ struct thermal_zone_device *tzd;
+ int ret, irq, i;
+
+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->id = (uintptr_t)device_get_match_data(dev);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ data->regs = devm_ioremap(dev, res->start, resource_size(res));
+ if (IS_ERR(data->regs))
+ return PTR_ERR(data->regs);
+
+ /* get irq */
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0)
+ return irq;
+
+ if (data->id > LOONGSON2_SOC_MAX_SENSOR_NUM - 1 || data->id < 0) {
+ dev_err(dev, "sensor id error,must be in <0 ~ %d>\n",
+ LOONGSON2_SOC_MAX_SENSOR_NUM - 1);
+ return -EINVAL;
+ }
+
+ writeb(0xff, data->regs + LOONGSON2_TSENSOR_STATUS);
+
+ loongson2_thermal_set(data, 0, 0, false);
+
+ for (i = 0; i < LOONGSON2_SOC_MAX_SENSOR_NUM; i++) {
+ tzd = devm_thermal_of_zone_register(&pdev->dev, i,
+ data, &loongson2_of_thermal_ops);
+
+ if (!IS_ERR(tzd))
+ break;
+
+ if (PTR_ERR(tzd) != ENODEV)
+ continue;
+
+ return dev_err_probe(&pdev->dev, PTR_ERR(tzd),
+ "failed to register");
+ }
+
+ ret = devm_request_threaded_irq(dev, irq, NULL, loongson2_thermal_irq_thread,
+ IRQF_ONESHOT, "loongson2_thermal", tzd);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "failed to request alarm irq\n");
+
+ if (devm_thermal_add_hwmon_sysfs(tzd))
+ dev_warn(&pdev->dev, "Failed to add hwmon sysfs attributes\n");
+
+ return 0;
+}
+
+static const struct of_device_id of_loongson2_thermal_match[] = {
+ { .compatible = "loongson,ls2k-thermal", .data = (const void *)0},
+ { /* end */ }
+};
+MODULE_DEVICE_TABLE(of, of_loongson2_thermal_match);
+
+static struct platform_driver loongson2_thermal_driver = {
+ .driver = {
+ .name = "loongson2_thermal",
+ .of_match_table = of_loongson2_thermal_match,
+ },
+ .probe = loongson2_thermal_probe,
+};
+module_platform_driver(loongson2_thermal_driver);
+
+MODULE_DESCRIPTION("Loongson2 thermal driver");
+MODULE_LICENSE("GPL");