| Message ID | 4bdab00c5b6f4f8f95b53e586552acfa@hyperstone.com |
|---|---|
| State | New |
| Headers | show |
| Series | None | expand |
On Wed, 5 Apr 2023 at 13:57, Christian Löhle <CLoehle@hyperstone.com> wrote: > > SPI doesn't have the usual PROG path we can check for error bits > after moving back to TRAN. Instead it holds the line LOW until > completion. We can then check if the card shows any errors or > is in IDLE state, indicating the line is no longer LOW because > the card was reset. > > Signed-off-by: Christian Loehle <cloehle@hyperstone.com> > --- > drivers/mmc/core/block.c | 9 +++++++-- > 1 file changed, 7 insertions(+), 2 deletions(-) > > diff --git a/drivers/mmc/core/block.c b/drivers/mmc/core/block.c > index 16e262ddc954..35ff7101cbb1 100644 > --- a/drivers/mmc/core/block.c > +++ b/drivers/mmc/core/block.c > @@ -182,6 +182,7 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq, > int recovery_mode, > struct mmc_queue *mq); > static void mmc_blk_hsq_req_done(struct mmc_request *mrq); > +static int mmc_spi_err_check(struct mmc_card *card); > > static struct mmc_blk_data *mmc_blk_get(struct gendisk *disk) > { > @@ -553,7 +554,7 @@ static int __mmc_blk_ioctl_cmd(struct mmc_card *card, struct mmc_blk_data *md, > /* If it's an R1B response we need some more preparations. */ > busy_timeout_ms = idata->ic.cmd_timeout_ms ? : MMC_BLK_TIMEOUT_MS; > r1b_resp = (cmd.flags & MMC_RSP_R1B) == MMC_RSP_R1B; > - if (r1b_resp) > + if (r1b_resp && !mmc_host_is_spi(card->host)) > use_r1b_resp = mmc_prepare_busy_cmd(card->host, &cmd, > busy_timeout_ms); > > @@ -612,8 +613,12 @@ static int __mmc_blk_ioctl_cmd(struct mmc_card *card, struct mmc_blk_data *md, > if ((card->host->caps & MMC_CAP_WAIT_WHILE_BUSY) && use_r1b_resp) > return 0; > > + if (mmc_host_is_spi(card->host)) { > + if (idata->ic.write_flag) > + err = mmc_spi_err_check(card); > + } Nitpick: I would prefer to use an "early return" rather than an else-if here. Would you mind changing that? > /* Ensure RPMB/R1B command has completed by polling with CMD13. */ > - if (idata->rpmb || r1b_resp) > + else if (idata->rpmb || r1b_resp) > err = mmc_poll_for_busy(card, busy_timeout_ms, false, > MMC_BUSY_IO); > Other than the nitpick, this looks good to me! Kind regards Uffe
diff --git a/drivers/mmc/core/block.c b/drivers/mmc/core/block.c index 16e262ddc954..35ff7101cbb1 100644 --- a/drivers/mmc/core/block.c +++ b/drivers/mmc/core/block.c @@ -182,6 +182,7 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq, int recovery_mode, struct mmc_queue *mq); static void mmc_blk_hsq_req_done(struct mmc_request *mrq); +static int mmc_spi_err_check(struct mmc_card *card); static struct mmc_blk_data *mmc_blk_get(struct gendisk *disk) { @@ -553,7 +554,7 @@ static int __mmc_blk_ioctl_cmd(struct mmc_card *card, struct mmc_blk_data *md, /* If it's an R1B response we need some more preparations. */ busy_timeout_ms = idata->ic.cmd_timeout_ms ? : MMC_BLK_TIMEOUT_MS; r1b_resp = (cmd.flags & MMC_RSP_R1B) == MMC_RSP_R1B; - if (r1b_resp) + if (r1b_resp && !mmc_host_is_spi(card->host)) use_r1b_resp = mmc_prepare_busy_cmd(card->host, &cmd, busy_timeout_ms); @@ -612,8 +613,12 @@ static int __mmc_blk_ioctl_cmd(struct mmc_card *card, struct mmc_blk_data *md, if ((card->host->caps & MMC_CAP_WAIT_WHILE_BUSY) && use_r1b_resp) return 0; + if (mmc_host_is_spi(card->host)) { + if (idata->ic.write_flag) + err = mmc_spi_err_check(card); + } /* Ensure RPMB/R1B command has completed by polling with CMD13. */ - if (idata->rpmb || r1b_resp) + else if (idata->rpmb || r1b_resp) err = mmc_poll_for_busy(card, busy_timeout_ms, false, MMC_BUSY_IO);
SPI doesn't have the usual PROG path we can check for error bits after moving back to TRAN. Instead it holds the line LOW until completion. We can then check if the card shows any errors or is in IDLE state, indicating the line is no longer LOW because the card was reset. Signed-off-by: Christian Loehle <cloehle@hyperstone.com> --- drivers/mmc/core/block.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-)