diff mbox series

[v2,12/12] ARM: dts: exynos: Add Samsung Galaxy Tab 3 8.0 boards

Message ID 20230416133422.1949-13-aweber.kernel@gmail.com
State New
Headers show
Series Re-introduce Exynos4212 support and add Samsung Galaxy Tab 3 8.0 boards | expand

Commit Message

Artur Weber April 16, 2023, 1:34 p.m. UTC
Introduce support for the Galaxy Tab 3 8.0 series of boards:

 - Samsung Galaxy Tab 3 8.0 WiFi (SM-T310/lt01wifi)
 - Samsung Galaxy Tab 3 8.0 3G (SM-T311/lt013g)
 - Samsung Galaxy Tab 3 8.0 LTE (SM-T315/lt01lte)

What works:

 - Display and backlight
 - Touchscreen (without touchkeys)
 - GPIO buttons, hall sensor
 - WiFi and Bluetooth
 - USB, fuel gauge, charging (partial)
 - Accelerometer and magnetometer
 - WiFi model only: light sensor

Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
---
Display panel bindings are added by a separate patchset:
"[PATCH 0/3] Add Samsung S6D7AA0 panel controller driver"[1]

[1] https://lore.kernel.org/all/20230416131632.31673-1-aweber.kernel@gmail.com/
---
 arch/arm/boot/dts/Makefile                  |    3 +
 arch/arm/boot/dts/exynos4212-tab3-3g8.dts   |   30 +
 arch/arm/boot/dts/exynos4212-tab3-lte8.dts  |   43 +
 arch/arm/boot/dts/exynos4212-tab3-wifi8.dts |   25 +
 arch/arm/boot/dts/exynos4212-tab3.dtsi      | 1175 +++++++++++++++++++
 5 files changed, 1276 insertions(+)
 create mode 100644 arch/arm/boot/dts/exynos4212-tab3-3g8.dts
 create mode 100644 arch/arm/boot/dts/exynos4212-tab3-lte8.dts
 create mode 100644 arch/arm/boot/dts/exynos4212-tab3-wifi8.dts
 create mode 100644 arch/arm/boot/dts/exynos4212-tab3.dtsi

Comments

Henrik Grimler April 19, 2023, 8:23 p.m. UTC | #1
Hi Artur,

Nice to see some more Exynos arm boards!

As Krzysztof already said this does not apply on top of
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux.git/log/?h=next/dt,
but it seems to apply on top of v6.3-rc6.  If you use the --base arg
of git format-patch it makes it easier to figure out where it applies.

Running ./script/checkpatch.pl on the patches also points out two
typos in exynos4x12.dtsi and exynos4212.dtsi, would probably be nice
to fix those while you are at it.

See some more comments/questions below.

On Sun, Apr 16, 2023 at 03:34:22PM +0200, Artur Weber wrote:
> Introduce support for the Galaxy Tab 3 8.0 series of boards:
> 
>  - Samsung Galaxy Tab 3 8.0 WiFi (SM-T310/lt01wifi)
>  - Samsung Galaxy Tab 3 8.0 3G (SM-T311/lt013g)
>  - Samsung Galaxy Tab 3 8.0 LTE (SM-T315/lt01lte)
> 
> What works:
> 
>  - Display and backlight
>  - Touchscreen (without touchkeys)
>  - GPIO buttons, hall sensor
>  - WiFi and Bluetooth
>  - USB, fuel gauge, charging (partial)
>  - Accelerometer and magnetometer
>  - WiFi model only: light sensor
> 
> Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
> ---
> Display panel bindings are added by a separate patchset:
> "[PATCH 0/3] Add Samsung S6D7AA0 panel controller driver"[1]
> 
> [1] https://lore.kernel.org/all/20230416131632.31673-1-aweber.kernel@gmail.com/
> ---
>  arch/arm/boot/dts/Makefile                  |    3 +
>  arch/arm/boot/dts/exynos4212-tab3-3g8.dts   |   30 +
>  arch/arm/boot/dts/exynos4212-tab3-lte8.dts  |   43 +
>  arch/arm/boot/dts/exynos4212-tab3-wifi8.dts |   25 +
>  arch/arm/boot/dts/exynos4212-tab3.dtsi      | 1175 +++++++++++++++++++
>  5 files changed, 1276 insertions(+)
>  create mode 100644 arch/arm/boot/dts/exynos4212-tab3-3g8.dts
>  create mode 100644 arch/arm/boot/dts/exynos4212-tab3-lte8.dts
>  create mode 100644 arch/arm/boot/dts/exynos4212-tab3-wifi8.dts
>  create mode 100644 arch/arm/boot/dts/exynos4212-tab3.dtsi
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index efe4152e5846..e5f63b636637 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -217,6 +217,9 @@ dtb-$(CONFIG_ARCH_EXYNOS4) += \
>  	exynos4210-smdkv310.dtb \
>  	exynos4210-trats.dtb \
>  	exynos4210-universal_c210.dtb \
> +	exynos4212-tab3-3g8.dtb \
> +	exynos4212-tab3-lte8.dtb \
> +	exynos4212-tab3-wifi8.dtb \
>  	exynos4412-i9300.dtb \
>  	exynos4412-i9305.dtb \
>  	exynos4412-itop-elite.dtb \
> diff --git a/arch/arm/boot/dts/exynos4212-tab3-3g8.dts b/arch/arm/boot/dts/exynos4212-tab3-3g8.dts
> new file mode 100644
> index 000000000000..c503a2d351dd
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos4212-tab3-3g8.dts
> @@ -0,0 +1,30 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree
> + * source
> + *
> + * Copyright (c) 2013 Samsung Electronics Co., Ltd.
> + *		http://www.samsung.com
> + */
> +
> +/dts-v1/;
> +#include "exynos4212-tab3.dtsi"
> +
> +/ {
> +	model = "Samsung Galaxy Tab 3 8.0 3G (SM-T311) based on Exynos4212";
> +	compatible = "samsung,t311", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
> +	chassis-type = "tablet";
> +};
> +
> +/* Pin control sleep state overrides */
> +
> +&sleep0 {
> +		PIN_SLP(gpb-5, INPUT, UP);
> +};
> +
> +&sleep1 {
> +		PIN_SLP(gpl0-0, OUT0, NONE);
> +		PIN_SLP(gpl1-0, OUT0, NONE);
> +		PIN_SLP(gpl2-4, OUT0, NONE);
> +		PIN_SLP(gpm3-3, OUT1, NONE);
> +};
> diff --git a/arch/arm/boot/dts/exynos4212-tab3-lte8.dts b/arch/arm/boot/dts/exynos4212-tab3-lte8.dts
> new file mode 100644
> index 000000000000..158c6a2e24bf
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos4212-tab3-lte8.dts
> @@ -0,0 +1,43 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree
> + * source
> + *
> + * Copyright (c) 2013 Samsung Electronics Co., Ltd.
> + *		http://www.samsung.com
> + */
> +
> +/dts-v1/;
> +#include "exynos4212-tab3.dtsi"
> +
> +/ {
> +	model = "Samsung Galaxy Tab 3 8.0 LTE (SM-T315) based on Exynos4212";
> +	compatible = "samsung,t315", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
> +	chassis-type = "tablet";
> +};
> +
> +&sleep0 {
> +		PIN_SLP(gpa0-4, INPUT, UP);
> +		PIN_SLP(gpa0-5, INPUT, UP);
> +
> +		PIN_SLP(gpb-5, INPUT, UP);
> +
> +		PIN_SLP(gpc0-0, PREV, NONE);
> +		PIN_SLP(gpc1-3, INPUT, NONE);
> +
> +		PIN_SLP(gpf1-6, INPUT, NONE);
> +		PIN_SLP(gpf2-2, PREV, NONE);
> +};
> +
> +&sleep1 {
> +		PIN_SLP(gpl0-0, PREV, NONE);
> +
> +		PIN_SLP(gpl1-0, PREV, NONE);
> +
> +		PIN_SLP(gpl2-1, INPUT, DOWN);
> +		PIN_SLP(gpl2-2, INPUT, DOWN);
> +		PIN_SLP(gpl2-4, OUT0, NONE);
> +		PIN_SLP(gpl2-5, PREV, NONE);
> +
> +		PIN_SLP(gpm3-3, OUT1, NONE);
> +};
> diff --git a/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts b/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts
> new file mode 100644
> index 000000000000..0527a75710d8
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts
> @@ -0,0 +1,25 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree
> + * source
> + *
> + * Copyright (c) 2013 Samsung Electronics Co., Ltd.
> + *		http://www.samsung.com
> + */
> +
> +/dts-v1/;
> +#include "exynos4212-tab3.dtsi"
> +
> +/ {
> +	model = "Samsung Galaxy Tab 3 8.0 WiFi (SM-T310) based on Exynos4212";
> +	compatible = "samsung,t310", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
> +	chassis-type = "tablet";
> +};
> +
> +&i2c_lightsensor {
> +	/* Capella Micro CM3323 color light sensor */
> +	colorsensor@10 {
> +		compatible = "capella,cm3323";
> +		reg = <0x10>;
> +	};
> +};
> diff --git a/arch/arm/boot/dts/exynos4212-tab3.dtsi b/arch/arm/boot/dts/exynos4212-tab3.dtsi
> new file mode 100644
> index 000000000000..b8ad5497506c
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos4212-tab3.dtsi
> @@ -0,0 +1,1175 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung's Exynos4212 based Galaxy Tab 3 board common source
> + *
> + * Copyright (c) 2013 Samsung Electronics Co., Ltd.
> + *		http://www.samsung.com
> + */
> +
> +/dts-v1/;
> +#include "exynos4212.dtsi"
> +#include "exynos4412-ppmu-common.dtsi"
> +#include "exynos-mfc-reserved-memory.dtsi"
> +#include <dt-bindings/clock/samsung,s2mps11.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include "exynos-pinctrl.h"
> +
> +/ {
> +	compatible = "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
> +
> +	memory@40000000 {
> +		device_type = "memory";
> +
> +		/* Technically 2GB, but last 1GB is flaky, so we ignore it for now */
> +		reg = <0x40000000 0x3FC00000>;

Comment says 1GB but you are skipping 1GB+4MB.  Is the entire region
flaky or perhaps just the 4MB region in the middle?

> +	};
> +
> +	chosen {
> +		stdout-path = &serial_2;
> +
> +		/* Default S-BOOT bootloader loads initramfs here */
> +		linux,initrd-start = <0x42000000>;
> +		linux,initrd-end = <0x42800000>;
> +	};
> +
> +	firmware@204f000 {
> +		compatible = "samsung,secure-firmware";
> +		reg = <0x0204F000 0x1000>;
> +	};
> +
> +	fixed-rate-clocks {
> +		xxti {
> +			compatible = "samsung,clock-xxti";
> +			clock-frequency = <0>;
> +		};
> +
> +		xusbxti {
> +			compatible = "samsung,clock-xusbxti";
> +			clock-frequency = <24000000>;
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&gpio_keys>;
> +
> +		key-power {
> +			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_POWER>;
> +			label = "power";
> +			debounce-interval = <10>;
> +			wakeup-source;
> +		};
> +
> +		key-up {
> +			gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_VOLUMEUP>;
> +			label = "volume down";
> +			debounce-interval = <10>;
> +		};
> +
> +		key-down {
> +			gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_VOLUMEDOWN>;
> +			label = "volume up";
> +			debounce-interval = <10>;
> +		};
> +
> +		key-home {
> +			gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_HOME>;
> +			label = "home";
> +			debounce-interval = <10>;
> +		};
> +
> +		switch-hall-sensor {
> +			gpios = <&gpx2 4 GPIO_ACTIVE_LOW>;
> +			linux,input-type = <EV_SW>;
> +			linux,code = <SW_LID>;
> +			linux,can-disable;
> +			label = "hall effect sensor";
> +			debounce-interval = <10>;
> +			wakeup-source;
> +		};
> +	};
> +
> +	vbatt_reg: voltage-regulator-1 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VBATT";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +
> +	backlight_reset_supply: voltage-regulator-2 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "BACKLIGHT_ENVDDIO";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&backlight_reset>;
> +		gpio = <&gpm0 1 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	lcd_enable_supply: voltage-regulator-3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "LCD_VDD_2.2V";
> +		regulator-min-microvolt = <2200000>;
> +		regulator-max-microvolt = <2200000>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&lcd_en>;
> +		gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; /* LCD_EN */
> +		enable-active-high;
> +	};
> +
> +	i2c_max77693: i2c-gpio-1 {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		i2c-gpio,delay-us = <2>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";
> +
> +		pmic@66 {
> +			compatible = "maxim,max77693";
> +			interrupt-parent = <&gpx1>;
> +			interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&max77693_irq>;
> +			reg = <0x66>;
> +
> +			regulators {
> +				esafeout1_reg: ESAFEOUT1 {
> +					regulator-name = "ESAFEOUT1";
> +					regulator-boot-on;
> +				};
> +
> +				esafeout2_reg: ESAFEOUT2 {
> +					regulator-name = "ESAFEOUT2";
> +				};
> +
> +				charger_reg: CHARGER {
> +					regulator-name = "CHARGER";
> +					regulator-min-microamp = <60000>;
> +					regulator-max-microamp = <2580000>;
> +					regulator-boot-on;
> +				};
> +			};
> +
> +			charger {
> +				compatible = "maxim,max77693-charger";
> +
> +				maxim,constant-microvolt = <4350000>;
> +				maxim,min-system-microvolt = <3600000>;
> +				maxim,thermal-regulation-celsius = <100>;
> +				maxim,battery-overcurrent-microamp = <3500000>;
> +				maxim,charge-input-threshold-microvolt = <4300000>;
> +			};
> +		};
> +	};
> +
> +	i2c_max77693_fuel: i2c-gpio-2 {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		i2c-gpio,delay-us = <2>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";
> +
> +		fuel-gauge@36 {
> +			compatible = "maxim,max17050";
> +			interrupt-parent = <&gpx2>;
> +			interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&max77693_fuel_irq>;
> +			reg = <0x36>;
> +
> +			maxim,over-heat-temp = <500>;
> +			maxim,over-volt = <4500>;
> +		};
> +	};
> +
> +	i2c_yas532_magnetometer: i2c-gpio-3 {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		i2c-gpio,delay-us = <2>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";
> +
> +		/* Magnetometer: Yamaha YAS532 */
> +		magnetometer@2e {
> +			compatible = "yamaha,yas532";
> +			reg = <0x2e>;
> +			iovdd-supply = <&ldo3_reg>; /* VCC_1.8V_AP */
> +			mount-matrix = "-1", "0", "0",
> +					  "0", "1", "0",
> +					  "0", "0", "-1";
> +		};
> +	};
> +
> +	i2c_lightsensor: i2c-gpio-4 {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&gpl0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&gpl0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		i2c-gpio,delay-us = <2>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";
> +
> +		/* WiFi model uses CM3323, 3G/LTE use CM36653 */
> +	};
> +
> +	i2c_bl: i2c-gpio-24 {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&gpm4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&gpm4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		status = "okay";
> +
> +		backlight: backlight@2c {
> +			compatible = "ti,lp8556";
> +			reg = <0x2c>;
> +			status = "okay";
> +
> +			bl-name = "lcd-bl";
> +			dev-ctrl = /bits/ 8 <0x80>;
> +			init-brt = /bits/ 8 <0x78>; /* 120 */
> +
> +			power-supply = <&vbatt_reg>;
> +			enable-supply = <&backlight_reset_supply>;
> +
> +			pwms = <&pwm 1 78770 0>;
> +			pwm-names = "lp8556";
> +			pwm-period = <78770>;
> +
> +			rom_a3h {
> +				rom-addr = /bits/ 8 <0xa3>;
> +				rom-val = /bits/ 8 <0x5e>;
> +			};
> +
> +			rom_a5h {
> +				rom-addr = /bits/ 8 <0xa5>;
> +				rom-val = /bits/ 8 <0x34>;
> +			};
> +
> +			rom_a7h {
> +				rom-addr = /bits/ 8 <0xa7>;
> +				rom-val = /bits/ 8 <0xfa>;
> +			};
> +		};
> +	};
> +
> +	wlan_pwrseq: sdhci3-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>;
> +	};
> +};
> +
> +&bus_dmc {
> +	devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
> +	vdd-supply = <&buck1_reg>;
> +	status = "okay";
> +};
> +
> +&bus_acp {
> +	devfreq = <&bus_dmc>;
> +	status = "okay";
> +};
> +
> +&bus_c2c {
> +	devfreq = <&bus_dmc>;
> +	status = "okay";
> +};
> +
> +&bus_leftbus {
> +	devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
> +	vdd-supply = <&buck3_reg>;
> +	status = "okay";
> +};
> +
> +&bus_rightbus {
> +	devfreq = <&bus_leftbus>;
> +	status = "okay";
> +};
> +
> +&bus_display {
> +	devfreq = <&bus_leftbus>;
> +	status = "okay";
> +};
> +
> +&bus_fsys {
> +	devfreq = <&bus_leftbus>;
> +	status = "okay";
> +};
> +
> +&bus_peri {
> +	devfreq = <&bus_leftbus>;
> +	status = "okay";
> +};
> +
> +&bus_mfc {
> +	devfreq = <&bus_leftbus>;
> +	status = "okay";
> +};
> +
> +&cpu0 {
> +	cpu0-supply = <&buck2_reg>;
> +};
> +
> +&dsi_0 {
> +	vddcore-supply = <&ldo8_reg>;
> +	vddio-supply = <&ldo10_reg>;
> +	samsung,burst-clock-frequency = <500000000>;
> +	samsung,esc-clock-frequency = <20000000>;
> +	samsung,pll-clock-frequency = <24000000>;
> +	status = "okay";
> +
> +	panel@0 {
> +		compatible = "samsung,s6d7aa0-lsl080al02";
> +		reg = <0>;
> +		enable-supply = <&lcd_enable_supply>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&lcd_nrst>;
> +		reset-gpios = <&gpf0 4 GPIO_ACTIVE_LOW>;
> +		backlight = <&backlight>;
> +	};
> +};
> +
> +&exynos_usbphy {
> +	vbus-supply = <&esafeout1_reg>;
> +	status = "okay";
> +};
> +
> +&fimd {
> +	status = "okay";
> +};
> +
> +&gpu {
> +	mali-supply = <&buck4_reg>;
> +	status = "okay";
> +};
> +
> +&hsotg {
> +	vusb_d-supply = <&ldo15_reg>;
> +	vusb_a-supply = <&ldo12_reg>;
> +	dr_mode = "peripheral";
> +	status = "okay";
> +};
> +
> +/* Accelerometer: K2DH/K3DH */
> +&i2c_1 {
> +	pinctrl-0 = <&i2c1_bus>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	lis3dh: accelerometer@19 {
> +		/* K2DH seems to be the same as lis2dh12 in terms of registers */
> +		compatible = "st,lis2dh12-accel";
> +		reg = <0x19>;
> +
> +		interrupt-parent = <&gpx0>;
> +		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
> +
> +		vdd-supply = <&ldo17_reg>; /* VCC_2.8V_AP */
> +		vddio-supply = <&ldo3_reg>; /* VCC_1.8V_AP */
> +
> +		mount-matrix = "-1", "0", "0",
> +				  "0", "1", "0",
> +				  "0", "0", "-1";
> +	};
> +};
> +
> +/* Touchscreen: MMS252 */
> +&i2c_3 {
> +	samsung,i2c-sda-delay = <100>;
> +	samsung,i2c-slave-addr = <0x10>;
> +	samsung,i2c-max-bus-freq = <400000>;
> +	pinctrl-0 = <&i2c3_bus>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	touchscreen@48 {
> +		/* Using mms114 compatible for now */
> +		compatible = "melfas,mms114";
> +		reg = <0x48>;
> +		interrupt-parent = <&gpb>;
> +		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
> +		touchscreen-size-x = <800>;
> +		touchscreen-size-y = <1280>;
> +		avdd-supply = <&ldo21_reg>;
> +		vdd-supply = <&ldo25_reg>;
> +	};
> +};
> +
> +/* PMIC: s5m8767 */
> +&i2c_7 {
> +	samsung,i2c-sda-delay = <100>;
> +	samsung,i2c-slave-addr = <0x10>;
> +	samsung,i2c-max-bus-freq = <100000>;
> +	pinctrl-0 = <&i2c7_bus>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	s5m8767: pmic@66 {
> +		compatible = "samsung,s5m8767-pmic";
> +		reg = <0x66>;
> +		interrupt-parent = <&gpx0>;
> +		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
> +		wakeup-source;
> +
> +		s5m8767,pmic-buck2-ramp-enable;
> +		s5m8767,pmic-buck3-ramp-enable;
> +		s5m8767,pmic-buck4-ramp-enable;
> +
> +		s5m8767,pmic-buck-ramp-delay = <25>;
> +		s5m8767,pmic-buck-default-dvs-idx = <1>;
> +
> +		s5m8767,pmic-buck-dvs-gpios = <&gpm3 0 GPIO_ACTIVE_HIGH>,
> +						 <&gpm3 1 GPIO_ACTIVE_HIGH>,
> +						 <&gpm3 2 GPIO_ACTIVE_HIGH>;
> +
> +		s5m8767,pmic-buck-ds-gpios = <&gpf3 1 GPIO_ACTIVE_HIGH>,
> +						 <&gpf3 2 GPIO_ACTIVE_HIGH>,
> +						 <&gpf3 3 GPIO_ACTIVE_HIGH>;
> +
> +		s5m8767,pmic-buck2-dvs-voltage = <1100000>, <1100000>,
> +						<1100000>, <1100000>,
> +						<1100000>, <1100000>,
> +						<1100000>, <1100000>;
> +
> +		s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
> +						<1100000>, <1100000>,
> +						<1100000>, <1100000>,
> +						<1100000>, <1100000>;
> +
> +		s5m8767,pmic-buck4-dvs-voltage = <1100000>, <1100000>,
> +						<1100000>, <1100000>,
> +						<1100000>, <1100000>,
> +						<1100000>, <1100000>;
> +
> +		regulators {
> +			ldo1_reg: LDO1 {
> +				regulator-name = "VALIVE_1.0V_AP";
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <1000000>;
> +				regulator-always-on;
> +				regulator-boot-on;
> +				op_mode = <1>;
> +			};
> +
> +			ldo2_reg: LDO2 {
> +				regulator-name = "VM1M2_1.2V_AP";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <1200000>;
> +				regulator-always-on;
> +				regulator-boot-on;
> +				op_mode = <1>;
> +			};
> +
> +			ldo3_reg: LDO3 {
> +				regulator-name = "VCC_1.8V_AP";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-always-on;
> +				op_mode = <1>;
> +			};
> +
> +			ldo5_reg: LDO5 {
> +				regulator-name = "VCC_3.3V_MHL";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				op_mode = <1>;
> +			};
> +
> +			ldo8_reg: LDO8 {
> +				regulator-name = "VMIPI_1.0V";
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <1000000>;
> +				op_mode = <3>;
> +			};
> +
> +			ldo9_reg: LDO9 {
> +				regulator-name = "VSIL_1.2V";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <1200000>;
> +				op_mode = <1>;
> +			};
> +
> +			ldo10_reg: LDO10 {
> +				regulator-name = "VMIPI_1.8V";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				op_mode = <3>;
> +			};
> +
> +			ldo12_reg: LDO12 {
> +				regulator-name = "VUOTG_3.0V";
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +				op_mode = <1>;
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			ldo13_reg: LDO13 {
> +				regulator-name = "VCC_1.8V_MHL";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				op_mode = <1>;
> +			};
> +
> +			ldo15_reg: LDO15 {
> +				regulator-name = "VHSIC_1.0V";
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <1000000>;
> +				op_mode = <1>;
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +				};
> +			};
> +
> +			ldo17_reg: LDO17 {
> +				regulator-name = "VCC_2.8V_AP";
> +				regulator-min-microvolt = <2800000>;
> +				regulator-max-microvolt = <2800000>;
> +				op_mode = <1>;
> +				regulator-always-on;
> +			};
> +
> +			ldo19_reg: LDO19 {
> +				regulator-name = "VLED_IC_1.9V";
> +				regulator-min-microvolt = <1900000>;
> +				regulator-max-microvolt = <1900000>;
> +				op_mode = <1>;
> +				regulator-always-on;
> +			};
> +
> +			ldo20_reg: LDO20 {
> +				regulator-name = "VTOUCH_3.3V";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				op_mode = <1>;
> +			};
> +
> +			ldo21_reg: LDO21 {
> +				regulator-name = "TSP_VDD_3.3V";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				op_mode = <1>;
> +			};
> +
> +			ldo22_reg: LDO22 {
> +				regulator-name = "5M_AF_2.8V";
> +				regulator-min-microvolt = <2800000>;
> +				regulator-max-microvolt = <2800000>;
> +				op_mode = <1>;
> +			};
> +
> +			ldo23_reg: LDO23 {
> +				regulator-name = "VTF_2.8V";
> +				regulator-min-microvolt = <2800000>;
> +				regulator-max-microvolt = <2800000>;
> +				op_mode = <3>;
> +			};
> +
> +			ldo24_reg: LDO24 {
> +				regulator-name = "LEDA_2.8V";
> +				regulator-min-microvolt = <2800000>;
> +				regulator-max-microvolt = <2800000>;
> +				op_mode = <1>;
> +			};
> +
> +			ldo25_reg: LDO25 {
> +				regulator-name = "TSP_VDD_1.8V";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				op_mode = <1>;
> +			};
> +
> +			ldo26_reg: LDO26 {
> +				regulator-name = "CAM_IO_1.8V";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				op_mode = <1>;
> +			};
> +
> +			ldo27_reg: LDO27 {
> +				regulator-name = "VTCAM_1.8V";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				op_mode = <1>;
> +			};
> +
> +			buck1_reg: BUCK1 {
> +				regulator-name = "VDD_MIF";
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <1100000>;
> +				regulator-always-on;
> +				regulator-boot-on;
> +				op_mode = <3>;
> +			};
> +
> +			buck2_reg: BUCK2 {
> +				regulator-name = "VDD_ARM";
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <1500000>;
> +				regulator-always-on;
> +				regulator-boot-on;
> +				op_mode = <3>;
> +			};
> +
> +			buck3_reg: BUCK3 {
> +				regulator-name = "VDD_INT";
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <1300000>;
> +				regulator-always-on;
> +				regulator-boot-on;
> +				op_mode = <3>;
> +			};
> +
> +			buck4_reg: BUCK4 {
> +				regulator-name = "VDD_G3D";
> +				regulator-min-microvolt = <850000>;
> +				regulator-max-microvolt = <1150000>;
> +				regulator-boot-on;
> +				op_mode = <3>;
> +			};
> +
> +			buck5_reg: BUCK5 {
> +				regulator-name = "VMEM_1.2V_AP";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt	= <1200000>;
> +				regulator-always-on;
> +				regulator-boot-on;
> +				op_mode = <1>;
> +			};
> +
> +			buck6_reg: BUCK6 {
> +				regulator-name = "CAM_ISP_CORE_1.2V";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <1200000>;
> +				op_mode = <1>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +		};
> +
> +		s5m8767_osc: clocks {
> +			compatible = "samsung,s5m8767-clk";
> +			#clock-cells = <1>;
> +			clock-output-names = "en32khz_ap",
> +						 "en32khz_cp",
> +						 "en32khz_bt";
> +		};
> +	};
> +};
> +
> +&mshc_0 {
> +	broken-cd;
> +	non-removable;
> +	card-detect-delay = <200>;
> +	vmmc-supply = <&ldo22_reg>;
> +	clock-frequency = <400000000>;
> +	samsung,dw-mshc-ciu-div = <0>;
> +	samsung,dw-mshc-sdr-timing = <2 3>;
> +	samsung,dw-mshc-ddr-timing = <1 2>;
> +	pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +	bus-width = <8>;
> +	cap-mmc-highspeed;

Please add mmc-ddr-1_8v; here as well.  It was added to the other
Exynos devices in commit 37f9514e618f ("ARM: dts: exynos: replace
mshc0 alias with mmc-ddr-1_8v property") which can be found in
Krzysztof's tree.

Best regards,
Henrik Grimler

> +};
> +
> +&pinctrl_0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sleep0>;
> +
> +	s5m8767_ds: s5m8767-ds {
> +		samsung,pins = "gpf3-1", "gpf3-2", "gpf3-3";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> +		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
> +	};
> +
> +	lcd_en: lcd-en {
> +		samsung,pins = "gpc0-1";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	lcd_nrst: lcd-nrst {
> +		samsung,pins = "gpf0-4";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	sleep0: sleep-state {
> +		PIN_SLP(gpa0-0, INPUT, NONE);
> +		PIN_SLP(gpa0-1, OUT0, NONE);
> +		PIN_SLP(gpa0-2, INPUT, NONE);
> +		PIN_SLP(gpa0-3, INPUT, UP);
> +		PIN_SLP(gpa0-4, INPUT, DOWN); /* UP on LTE model */
> +		PIN_SLP(gpa0-5, INPUT, DOWN); /* UP on LTE model */
> +		PIN_SLP(gpa0-6, INPUT, DOWN);
> +		PIN_SLP(gpa0-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpa1-0, INPUT, DOWN);
> +		PIN_SLP(gpa1-1, INPUT, DOWN);
> +		PIN_SLP(gpa1-2, INPUT, DOWN);
> +		PIN_SLP(gpa1-3, INPUT, DOWN);
> +		PIN_SLP(gpa1-4, INPUT, DOWN);
> +		PIN_SLP(gpa1-5, INPUT, DOWN);
> +
> +		PIN_SLP(gpb-0, INPUT, NONE);
> +		PIN_SLP(gpb-1, INPUT, NONE);
> +		PIN_SLP(gpb-2, INPUT, NONE);
> +		PIN_SLP(gpb-3, INPUT, NONE);
> +		PIN_SLP(gpb-4, INPUT, DOWN);
> +		PIN_SLP(gpb-5, INPUT, DOWN); /* UP on all models with modem */
> +		PIN_SLP(gpb-6, INPUT, DOWN);
> +		PIN_SLP(gpb-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpc0-0, INPUT, DOWN); /* PREV, NONE on LTE model */
> +		PIN_SLP(gpc0-1, INPUT, DOWN);
> +		PIN_SLP(gpc0-2, INPUT, DOWN);
> +		PIN_SLP(gpc0-3, INPUT, DOWN);
> +		PIN_SLP(gpc0-4, INPUT, DOWN);
> +
> +		PIN_SLP(gpc1-0, INPUT, DOWN);
> +		PIN_SLP(gpc1-1, INPUT, DOWN);
> +		PIN_SLP(gpc1-2, INPUT, DOWN);
> +		PIN_SLP(gpc1-3, INPUT, DOWN); /* NONE on LTE model */
> +		PIN_SLP(gpc1-4, INPUT, DOWN);
> +
> +		PIN_SLP(gpd0-0, INPUT, DOWN);
> +		PIN_SLP(gpd0-1, OUT0, NONE);
> +		PIN_SLP(gpd0-2, INPUT, NONE);
> +		PIN_SLP(gpd0-3, INPUT, NONE);
> +
> +		PIN_SLP(gpd1-0, INPUT, DOWN);
> +		PIN_SLP(gpd1-1, INPUT, DOWN);
> +		PIN_SLP(gpd1-2, INPUT, NONE);
> +		PIN_SLP(gpd1-3, INPUT, NONE);
> +
> +		PIN_SLP(gpf0-0, INPUT, DOWN);
> +		PIN_SLP(gpf0-1, INPUT, DOWN);
> +		PIN_SLP(gpf0-2, INPUT, DOWN);
> +		PIN_SLP(gpf0-3, INPUT, DOWN);
> +		PIN_SLP(gpf0-4, OUT0, NONE);
> +		PIN_SLP(gpf0-5, OUT0, NONE);
> +		PIN_SLP(gpf0-6, INPUT, DOWN);
> +		PIN_SLP(gpf0-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpf1-0, INPUT, DOWN);
> +		PIN_SLP(gpf1-1, INPUT, DOWN);
> +		PIN_SLP(gpf1-2, INPUT, DOWN);
> +		PIN_SLP(gpf1-3, INPUT, DOWN);
> +		PIN_SLP(gpf1-4, INPUT, DOWN);
> +		PIN_SLP(gpf1-5, INPUT, DOWN);
> +		PIN_SLP(gpf1-6, INPUT, DOWN); /* NONE on LTE model */
> +		PIN_SLP(gpf1-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpf2-0, INPUT, DOWN);
> +		PIN_SLP(gpf2-1, INPUT, DOWN);
> +		PIN_SLP(gpf2-2, INPUT, DOWN); /* PREV, NONE on LTE model */
> +		PIN_SLP(gpf2-3, INPUT, DOWN);
> +		PIN_SLP(gpf2-4, INPUT, DOWN);
> +		PIN_SLP(gpf2-5, INPUT, DOWN);
> +		PIN_SLP(gpf2-6, INPUT, DOWN);
> +		PIN_SLP(gpf2-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpf3-0, INPUT, DOWN);
> +		PIN_SLP(gpf3-1, INPUT, DOWN);
> +		PIN_SLP(gpf3-2, INPUT, DOWN);
> +		PIN_SLP(gpf3-3, INPUT, DOWN);
> +		PIN_SLP(gpf3-4, PREV, NONE);
> +		PIN_SLP(gpf3-5, OUT0, DOWN);
> +
> +		PIN_SLP(gpj0-0, INPUT, DOWN);
> +		PIN_SLP(gpj0-1, INPUT, DOWN);
> +		PIN_SLP(gpj0-2, INPUT, DOWN);
> +		PIN_SLP(gpj0-3, OUT0, NONE);
> +		PIN_SLP(gpj0-4, INPUT, DOWN);
> +		PIN_SLP(gpj0-5, INPUT, DOWN);
> +		PIN_SLP(gpj0-6, OUT0, NONE);
> +		PIN_SLP(gpj0-7, OUT0, NONE);
> +
> +		PIN_SLP(gpj1-0, OUT0, NONE);
> +		PIN_SLP(gpj1-1, INPUT, DOWN);
> +		PIN_SLP(gpj1-2, PREV, NONE);
> +		PIN_SLP(gpj1-3, INPUT, DOWN);
> +		PIN_SLP(gpj1-4, INPUT, DOWN);
> +	};
> +};
> +
> +&pinctrl_1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sleep1>;
> +
> +	max77693_irq: max77693-irq {
> +		samsung,pins = "gpx1-5";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
> +	};
> +
> +	max77693_fuel_irq: max77693-fuel-irq {
> +		samsung,pins = "gpx2-3";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
> +	};
> +
> +	s5m8767_dvs: s5m8767-dvs {
> +		samsung,pins = "gpm3-0", "gpm3-1", "gpm3-2";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
> +	};
> +
> +	s5m8767_irq: s5m8767-irq {
> +		samsung,pins = "gpx0-7";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
> +	};
> +
> +	sdhci2_cd: sdhci2-cd-irq {
> +		samsung,pins = "gpx3-4";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
> +	};
> +
> +	bt_shutdown: bt-shutdown-pins {
> +		samsung,pins = "gpl0-6";
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	bt_host_wakeup: bt-host-wakeup-pins {
> +		samsung,pins = "gpx2-6";
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	bt_device_wakeup: bt-device-wakeup-pins {
> +		samsung,pins = "gpx3-1";
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	backlight_reset: backlight-reset {
> +		samsung,pins = "gpm0-1";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	gpio_keys: gpio-keys-pins {
> +		samsung,pins = "gpx1-2", "gpx2-2", "gpx2-4", "gpx2-7", "gpx3-3";
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	sleep1: sleep-state {
> +		PIN_SLP(gpk0-0, PREV, NONE);
> +		PIN_SLP(gpk0-1, PREV, NONE);
> +		PIN_SLP(gpk0-2, PREV, NONE);
> +		PIN_SLP(gpk0-3, PREV, NONE);
> +		PIN_SLP(gpk0-4, PREV, NONE);
> +		PIN_SLP(gpk0-5, PREV, NONE);
> +		PIN_SLP(gpk0-6, PREV, NONE);
> +
> +		PIN_SLP(gpk1-0, INPUT, DOWN);
> +		PIN_SLP(gpk1-1, INPUT, DOWN);
> +		PIN_SLP(gpk1-2, INPUT, DOWN);
> +		PIN_SLP(gpk1-3, PREV, NONE);
> +		PIN_SLP(gpk1-4, PREV, NONE);
> +		PIN_SLP(gpk1-5, PREV, NONE);
> +		PIN_SLP(gpk1-6, PREV, NONE);
> +
> +		PIN_SLP(gpk2-0, INPUT, DOWN);
> +		PIN_SLP(gpk2-1, INPUT, DOWN);
> +		PIN_SLP(gpk2-2, INPUT, DOWN);
> +		PIN_SLP(gpk2-3, INPUT, DOWN);
> +		PIN_SLP(gpk2-4, INPUT, DOWN);
> +		PIN_SLP(gpk2-5, INPUT, DOWN);
> +		PIN_SLP(gpk2-6, INPUT, DOWN);
> +
> +		PIN_SLP(gpk3-0, OUT0, NONE);
> +		PIN_SLP(gpk3-1, INPUT, NONE);
> +		PIN_SLP(gpk3-2, INPUT, DOWN);
> +		PIN_SLP(gpk3-3, INPUT, NONE);
> +		PIN_SLP(gpk3-4, INPUT, NONE);
> +		PIN_SLP(gpk3-5, INPUT, NONE);
> +		PIN_SLP(gpk3-6, INPUT, NONE);
> +
> +		PIN_SLP(gpl0-0, INPUT, DOWN); /* OUT0 on 3G, PREV on LTE; NONE on both */
> +		PIN_SLP(gpl0-1, INPUT, NONE);
> +		PIN_SLP(gpl0-2, INPUT, NONE);
> +		PIN_SLP(gpl0-3, INPUT, DOWN);
> +		PIN_SLP(gpl0-4, INPUT, DOWN);
> +		PIN_SLP(gpl0-6, PREV, NONE);
> +
> +		PIN_SLP(gpl1-0, INPUT, DOWN); /* OUT0 on 3G, PREV on LTE; NONE on both */
> +		PIN_SLP(gpl1-1, OUT0, NONE);
> +		PIN_SLP(gpl2-0, INPUT, DOWN);
> +		PIN_SLP(gpl2-1, PREV, NONE); /* INPUT, DOWN on LTE */
> +		PIN_SLP(gpl2-2, PREV, NONE); /* INPUT, DOWN on LTE */
> +		PIN_SLP(gpl2-3, INPUT, DOWN);
> +		PIN_SLP(gpl2-4, INPUT, DOWN); /* OUT0, NONE on models with modem */
> +		PIN_SLP(gpl2-5, INPUT, DOWN); /* PREV, NONE on LTE */
> +		PIN_SLP(gpl2-6, INPUT, DOWN);
> +		PIN_SLP(gpl2-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpm0-0, PREV, NONE);
> +		PIN_SLP(gpm0-1, OUT0, NONE);
> +		PIN_SLP(gpm0-2, INPUT, DOWN);
> +		PIN_SLP(gpm0-3, INPUT, DOWN);
> +		PIN_SLP(gpm0-4, INPUT, DOWN);
> +		PIN_SLP(gpm0-5, INPUT, DOWN);
> +		PIN_SLP(gpm0-6, INPUT, DOWN);
> +		PIN_SLP(gpm0-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpm1-0, INPUT, DOWN);
> +		PIN_SLP(gpm1-1, INPUT, DOWN);
> +		PIN_SLP(gpm1-2, INPUT, NONE);
> +		PIN_SLP(gpm1-3, INPUT, NONE);
> +		PIN_SLP(gpm1-4, INPUT, NONE);
> +		PIN_SLP(gpm1-5, INPUT, NONE);
> +		PIN_SLP(gpm1-6, OUT0, NONE);
> +
> +		PIN_SLP(gpm2-0, INPUT, NONE);
> +		PIN_SLP(gpm2-1, INPUT, NONE);
> +		PIN_SLP(gpm2-2, OUT0, NONE);
> +		PIN_SLP(gpm2-3, INPUT, DOWN);
> +		PIN_SLP(gpm2-4, INPUT, DOWN);
> +
> +		PIN_SLP(gpm3-0, PREV, NONE);
> +		PIN_SLP(gpm3-1, PREV, NONE);
> +		PIN_SLP(gpm3-2, PREV, NONE);
> +		PIN_SLP(gpm3-3, INPUT, DOWN); /* OUT1, NONE for 3G */
> +		PIN_SLP(gpm3-4, INPUT, DOWN);
> +		PIN_SLP(gpm3-5, PREV, NONE);
> +		PIN_SLP(gpm3-6, INPUT, DOWN);
> +		PIN_SLP(gpm3-7, OUT0, NONE);
> +
> +		PIN_SLP(gpm4-0, INPUT, DOWN);
> +		PIN_SLP(gpm4-1, INPUT, DOWN);
> +		PIN_SLP(gpm4-2, INPUT, DOWN);
> +		PIN_SLP(gpm4-3, INPUT, DOWN);
> +		PIN_SLP(gpm4-4, PREV, NONE);
> +		PIN_SLP(gpm4-5, INPUT, NONE);
> +		PIN_SLP(gpm4-6, INPUT, DOWN);
> +		PIN_SLP(gpm4-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpy0-0, INPUT, DOWN);
> +		PIN_SLP(gpy0-1, INPUT, DOWN);
> +		PIN_SLP(gpy0-2, INPUT, NONE);
> +		PIN_SLP(gpy0-3, INPUT, NONE);
> +		PIN_SLP(gpy0-4, INPUT, DOWN);
> +		PIN_SLP(gpy0-5, INPUT, DOWN);
> +
> +		PIN_SLP(gpy1-0, INPUT, DOWN);
> +		PIN_SLP(gpy1-1, INPUT, DOWN);
> +		PIN_SLP(gpy1-2, INPUT, DOWN);
> +		PIN_SLP(gpy1-3, INPUT, DOWN);
> +
> +		PIN_SLP(gpy2-0, PREV, NONE);
> +		PIN_SLP(gpy2-1, INPUT, DOWN);
> +		PIN_SLP(gpy2-2, INPUT, NONE);
> +		PIN_SLP(gpy2-3, INPUT, NONE);
> +		PIN_SLP(gpy2-4, INPUT, NONE);
> +		PIN_SLP(gpy2-5, INPUT, NONE);
> +
> +		PIN_SLP(gpy3-0, INPUT, DOWN);
> +		PIN_SLP(gpy3-1, INPUT, DOWN);
> +		PIN_SLP(gpy3-2, INPUT, DOWN);
> +		PIN_SLP(gpy3-3, INPUT, DOWN);
> +		PIN_SLP(gpy3-4, INPUT, DOWN);
> +		PIN_SLP(gpy3-5, INPUT, DOWN);
> +		PIN_SLP(gpy3-6, INPUT, DOWN);
> +		PIN_SLP(gpy3-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpy4-0, INPUT, DOWN);
> +		PIN_SLP(gpy4-1, INPUT, DOWN);
> +		PIN_SLP(gpy4-2, INPUT, DOWN);
> +		PIN_SLP(gpy4-3, INPUT, DOWN);
> +		PIN_SLP(gpy4-4, INPUT, DOWN);
> +		PIN_SLP(gpy4-5, INPUT, DOWN);
> +		PIN_SLP(gpy4-6, INPUT, DOWN);
> +		PIN_SLP(gpy4-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpy5-0, INPUT, DOWN);
> +		PIN_SLP(gpy5-1, INPUT, DOWN);
> +		PIN_SLP(gpy5-2, INPUT, DOWN);
> +		PIN_SLP(gpy5-3, INPUT, DOWN);
> +		PIN_SLP(gpy5-4, INPUT, DOWN);
> +		PIN_SLP(gpy5-5, INPUT, DOWN);
> +		PIN_SLP(gpy5-6, INPUT, DOWN);
> +		PIN_SLP(gpy5-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpy6-0, INPUT, DOWN);
> +		PIN_SLP(gpy6-1, INPUT, DOWN);
> +		PIN_SLP(gpy6-2, INPUT, DOWN);
> +		PIN_SLP(gpy6-3, INPUT, DOWN);
> +		PIN_SLP(gpy6-4, INPUT, DOWN);
> +		PIN_SLP(gpy6-5, INPUT, DOWN);
> +		PIN_SLP(gpy6-6, INPUT, DOWN);
> +		PIN_SLP(gpy6-7, INPUT, DOWN);
> +	};
> +};
> +
> +&pinctrl_2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sleep2>;
> +
> +	sleep2: sleep-state {
> +		PIN_SLP(gpz-0, INPUT, DOWN);
> +		PIN_SLP(gpz-1, INPUT, DOWN);
> +		PIN_SLP(gpz-2, INPUT, DOWN);
> +		PIN_SLP(gpz-3, INPUT, DOWN);
> +		PIN_SLP(gpz-4, INPUT, DOWN);
> +		PIN_SLP(gpz-5, INPUT, DOWN);
> +		PIN_SLP(gpz-6, INPUT, DOWN);
> +	};
> +};
> +
> +&pinctrl_3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sleep3>;
> +
> +	sleep3: sleep-state {
> +		PIN_SLP(gpv0-0, INPUT, DOWN);
> +		PIN_SLP(gpv0-1, INPUT, DOWN);
> +		PIN_SLP(gpv0-2, INPUT, DOWN);
> +		PIN_SLP(gpv0-3, INPUT, DOWN);
> +		PIN_SLP(gpv0-4, INPUT, DOWN);
> +		PIN_SLP(gpv0-5, INPUT, DOWN);
> +		PIN_SLP(gpv0-6, INPUT, DOWN);
> +		PIN_SLP(gpv0-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpv1-0, INPUT, DOWN);
> +		PIN_SLP(gpv1-1, INPUT, DOWN);
> +		PIN_SLP(gpv1-2, INPUT, DOWN);
> +		PIN_SLP(gpv1-3, INPUT, DOWN);
> +		PIN_SLP(gpv1-4, INPUT, DOWN);
> +		PIN_SLP(gpv1-5, INPUT, DOWN);
> +		PIN_SLP(gpv1-6, INPUT, DOWN);
> +		PIN_SLP(gpv1-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpv2-0, INPUT, DOWN);
> +		PIN_SLP(gpv2-1, INPUT, DOWN);
> +		PIN_SLP(gpv2-2, INPUT, DOWN);
> +		PIN_SLP(gpv2-3, INPUT, DOWN);
> +		PIN_SLP(gpv2-4, INPUT, DOWN);
> +		PIN_SLP(gpv2-5, INPUT, DOWN);
> +		PIN_SLP(gpv2-6, INPUT, DOWN);
> +		PIN_SLP(gpv2-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpv3-0, INPUT, DOWN);
> +		PIN_SLP(gpv3-1, INPUT, DOWN);
> +		PIN_SLP(gpv3-2, INPUT, DOWN);
> +		PIN_SLP(gpv3-3, INPUT, DOWN);
> +		PIN_SLP(gpv3-4, INPUT, DOWN);
> +		PIN_SLP(gpv3-5, INPUT, DOWN);
> +		PIN_SLP(gpv3-6, INPUT, DOWN);
> +		PIN_SLP(gpv3-7, INPUT, DOWN);
> +
> +		PIN_SLP(gpv4-0, INPUT, DOWN);
> +		PIN_SLP(gpv4-1, INPUT, DOWN);
> +	};
> +};
> +
> +&pmu_system_controller {
> +	assigned-clocks = <&pmu_system_controller 0>;
> +	assigned-clock-parents = <&clock CLK_XUSBXTI>;
> +};
> +
> +&pwm {
> +	pinctrl-0 = <&pwm1_out>;
> +	pinctrl-names = "default";
> +	samsung,pwm-outputs = <1>;
> +	status = "okay";
> +};
> +
> +&rtc {
> +	status = "okay";
> +	clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>;
> +	clock-names = "rtc", "rtc_src";
> +};
> +
> +&sdhci_2 {
> +	bus-width = <4>;
> +	cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
> +	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>;
> +	pinctrl-names = "default";
> +	vmmc-supply = <&ldo23_reg>;
> +	status = "okay";
> +};
> +
> +&sdhci_3 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	non-removable;
> +	bus-width = <4>;
> +
> +	mmc-pwrseq = <&wlan_pwrseq>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
> +	status = "okay";
> +
> +	/* BCM4334 Wi-Fi */
> +	brcmf: wifi@1 {
> +		compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
> +		reg = <1>;
> +
> +		interrupt-parent = <&gpx2>;
> +		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-names = "host-wake";
> +	};
> +};
> +
> +&serial_0 {
> +	pinctrl-0 = <&uart0_data &uart0_fctl>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +
> +	/* BCM4334B0 Bluetooth */
> +	bluetooth {
> +		compatible = "brcm,bcm4330-bt";
> +		pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>;
> +		pinctrl-names = "default";
> +		max-speed = <3000000>;
> +		shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>;
> +		device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
> +		host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
> +		clocks = <&s5m8767_osc S2MPS11_CLK_BT>;
> +	};
> +};
> +
> +&serial_1 {
> +	status = "okay";
> +};
> +
> +&serial_2 {
> +	status = "okay";
> +};
> +
> +&serial_3 {
> +	status = "okay";
> +};
> +
> +&tmu {
> +	vtmu-supply = <&ldo10_reg>;
> +	status = "okay";
> +};
> -- 
> 2.40.0
>
Artur Weber April 22, 2023, 1:50 p.m. UTC | #2
Hi,

thank you for the review.

On 16/04/2023 20:26, Krzysztof Kozlowski wrote:
> On 16/04/2023 15:34, Artur Weber wrote:
> [...]
>> +
>> +		backlight: backlight@2c {
>> +			compatible = "ti,lp8556";
> 
> You need to convert bindings to DT schema first. I don't accept any new
> usages of TXT bindings anymore, sorry.
> 

I'll be taking a look at the conversion (will likely submit it as a
separate patchset, since I've been looking into some minor driver-side
changes there as well...), although I have one question - who should I
list as the bindings maintainer ("maintainers" field in YAML format)? Is
this someone specific for that subsystem, or the author of the driver,
or someone else? (It's worth noting that there isn't a maintainer listed
for the lp855x driver in the MAINTAINERS file.)
Documentation/devicetree/bindings/writing-schema.rst doesn't really
mention anything about this.

>> +&bus_acp {
> 
> Order label/phandle overrides by name, so acp before dmc.
> 

Out of curiosity - should I order the children of the / node or the
pinctrl nodes by name as well?

Best regards
Artur Weber
Krzysztof Kozlowski April 23, 2023, 8:25 a.m. UTC | #3
On 22/04/2023 15:50, Artur Weber wrote:
> Hi,
> 
> thank you for the review.
> 
> On 16/04/2023 20:26, Krzysztof Kozlowski wrote:
>> On 16/04/2023 15:34, Artur Weber wrote:
>> [...]
>>> +
>>> +		backlight: backlight@2c {
>>> +			compatible = "ti,lp8556";
>>
>> You need to convert bindings to DT schema first. I don't accept any new
>> usages of TXT bindings anymore, sorry.
>>
> 
> I'll be taking a look at the conversion (will likely submit it as a
> separate patchset, since I've been looking into some minor driver-side
> changes there as well...), although I have one question - who should I
> list as the bindings maintainer ("maintainers" field in YAML format)? Is

Anyone who has interest in the device/driver, like driver maintainer,
device developers, you erc.

> this someone specific for that subsystem, or the author of the driver,
> or someone else? (It's worth noting that there isn't a maintainer listed
> for the lp855x driver in the MAINTAINERS file.)
> Documentation/devicetree/bindings/writing-schema.rst doesn't really
> mention anything about this.
> 
>>> +&bus_acp {
>>
>> Order label/phandle overrides by name, so acp before dmc.
>>
> 
> Out of curiosity - should I order the children of the / node 

Yes.

> or the
> pinctrl nodes by name as well?

These are usually by pin name.


Best regards,
Krzysztof
Artur Weber April 23, 2023, 12:52 p.m. UTC | #4
Hi,

On 19/04/2023 22:23, Henrik Grimler wrote:
>> +	memory@40000000 {
>> +		device_type = "memory";
>> +
>> +		/* Technically 2GB, but last 1GB is flaky, so we ignore it for now */
>> +		reg = <0x40000000 0x3FC00000>;
> 
> Comment says 1GB but you are skipping 1GB+4MB.  Is the entire region
> flaky or perhaps just the 4MB region in the middle?

I copied the memory bank configuration from downstream: according to
boot logs and ATAG data from the stock bootloader, there are two memory
regions: one starting at 0x40000000 (size: 1020M) and one starting at
0x80000000 (size: 1024M). Here, only the first bank is added, since the
second one doesn't work.

I tried changing the size of this first bank to the full 1024M, and it
seems to be booting fine; still, I'd rather leave this at the same size
as claimed by downstream and ATAG.

The second memory bank (anything past 0x80000000) doesn't work, as
downstream has some weird special behavior regarding it: that region
contains "page holes", and there's a check that discards every second
page frame in that region[1][2]. That also means my comment is incorrect
- indeed, 2GB of memory are passed to the kernel, but the second 1GB is
effectively halved, leaving us with 1.5GB. (That's an oversight on my
part - I wasn't aware of this when writing the DTS initially, and only
checked this more in-depth now.)

I'm not sure if there's a way to re-create this behavior in mainline;
the closest thing I can think of is making a separate entry in reg for
each of the working pages, but that would leave us with hundreds of
lines, which is not ideal... so it's much easier to just leave it unused
for now.

Best regards
Artur Weber

[1]
https://github.com/gr8nole/android_kernel_samsung_smdk4x12/blob/786b1473b93aabf40c18a2dca035503cce5ecac7/arch/arm/mm/init.c#L413-L414
[2]
https://github.com/gr8nole/android_kernel_samsung_smdk4x12/blob/786b1473b93aabf40c18a2dca035503cce5ecac7/arch/arm/mach-exynos/include/mach/memory.h#L30-L38
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index efe4152e5846..e5f63b636637 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -217,6 +217,9 @@  dtb-$(CONFIG_ARCH_EXYNOS4) += \
 	exynos4210-smdkv310.dtb \
 	exynos4210-trats.dtb \
 	exynos4210-universal_c210.dtb \
+	exynos4212-tab3-3g8.dtb \
+	exynos4212-tab3-lte8.dtb \
+	exynos4212-tab3-wifi8.dtb \
 	exynos4412-i9300.dtb \
 	exynos4412-i9305.dtb \
 	exynos4412-itop-elite.dtb \
diff --git a/arch/arm/boot/dts/exynos4212-tab3-3g8.dts b/arch/arm/boot/dts/exynos4212-tab3-3g8.dts
new file mode 100644
index 000000000000..c503a2d351dd
--- /dev/null
+++ b/arch/arm/boot/dts/exynos4212-tab3-3g8.dts
@@ -0,0 +1,30 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree
+ * source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos4212-tab3.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 3 8.0 3G (SM-T311) based on Exynos4212";
+	compatible = "samsung,t311", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
+	chassis-type = "tablet";
+};
+
+/* Pin control sleep state overrides */
+
+&sleep0 {
+		PIN_SLP(gpb-5, INPUT, UP);
+};
+
+&sleep1 {
+		PIN_SLP(gpl0-0, OUT0, NONE);
+		PIN_SLP(gpl1-0, OUT0, NONE);
+		PIN_SLP(gpl2-4, OUT0, NONE);
+		PIN_SLP(gpm3-3, OUT1, NONE);
+};
diff --git a/arch/arm/boot/dts/exynos4212-tab3-lte8.dts b/arch/arm/boot/dts/exynos4212-tab3-lte8.dts
new file mode 100644
index 000000000000..158c6a2e24bf
--- /dev/null
+++ b/arch/arm/boot/dts/exynos4212-tab3-lte8.dts
@@ -0,0 +1,43 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree
+ * source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos4212-tab3.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 3 8.0 LTE (SM-T315) based on Exynos4212";
+	compatible = "samsung,t315", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
+	chassis-type = "tablet";
+};
+
+&sleep0 {
+		PIN_SLP(gpa0-4, INPUT, UP);
+		PIN_SLP(gpa0-5, INPUT, UP);
+
+		PIN_SLP(gpb-5, INPUT, UP);
+
+		PIN_SLP(gpc0-0, PREV, NONE);
+		PIN_SLP(gpc1-3, INPUT, NONE);
+
+		PIN_SLP(gpf1-6, INPUT, NONE);
+		PIN_SLP(gpf2-2, PREV, NONE);
+};
+
+&sleep1 {
+		PIN_SLP(gpl0-0, PREV, NONE);
+
+		PIN_SLP(gpl1-0, PREV, NONE);
+
+		PIN_SLP(gpl2-1, INPUT, DOWN);
+		PIN_SLP(gpl2-2, INPUT, DOWN);
+		PIN_SLP(gpl2-4, OUT0, NONE);
+		PIN_SLP(gpl2-5, PREV, NONE);
+
+		PIN_SLP(gpm3-3, OUT1, NONE);
+};
diff --git a/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts b/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts
new file mode 100644
index 000000000000..0527a75710d8
--- /dev/null
+++ b/arch/arm/boot/dts/exynos4212-tab3-wifi8.dts
@@ -0,0 +1,25 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4212 based Galaxy Tab 3 8.0 WiFi board device tree
+ * source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos4212-tab3.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 3 8.0 WiFi (SM-T310) based on Exynos4212";
+	compatible = "samsung,t310", "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
+	chassis-type = "tablet";
+};
+
+&i2c_lightsensor {
+	/* Capella Micro CM3323 color light sensor */
+	colorsensor@10 {
+		compatible = "capella,cm3323";
+		reg = <0x10>;
+	};
+};
diff --git a/arch/arm/boot/dts/exynos4212-tab3.dtsi b/arch/arm/boot/dts/exynos4212-tab3.dtsi
new file mode 100644
index 000000000000..b8ad5497506c
--- /dev/null
+++ b/arch/arm/boot/dts/exynos4212-tab3.dtsi
@@ -0,0 +1,1175 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos4212 based Galaxy Tab 3 board common source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ */
+
+/dts-v1/;
+#include "exynos4212.dtsi"
+#include "exynos4412-ppmu-common.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
+#include <dt-bindings/clock/samsung,s2mps11.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "exynos-pinctrl.h"
+
+/ {
+	compatible = "samsung,tab3", "samsung,exynos4212", "samsung,exynos4";
+
+	memory@40000000 {
+		device_type = "memory";
+
+		/* Technically 2GB, but last 1GB is flaky, so we ignore it for now */
+		reg = <0x40000000 0x3FC00000>;
+	};
+
+	chosen {
+		stdout-path = &serial_2;
+
+		/* Default S-BOOT bootloader loads initramfs here */
+		linux,initrd-start = <0x42000000>;
+		linux,initrd-end = <0x42800000>;
+	};
+
+	firmware@204f000 {
+		compatible = "samsung,secure-firmware";
+		reg = <0x0204F000 0x1000>;
+	};
+
+	fixed-rate-clocks {
+		xxti {
+			compatible = "samsung,clock-xxti";
+			clock-frequency = <0>;
+		};
+
+		xusbxti {
+			compatible = "samsung,clock-xusbxti";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys>;
+
+		key-power {
+			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			label = "power";
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+
+		key-up {
+			gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			label = "volume down";
+			debounce-interval = <10>;
+		};
+
+		key-down {
+			gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "volume up";
+			debounce-interval = <10>;
+		};
+
+		key-home {
+			gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOME>;
+			label = "home";
+			debounce-interval = <10>;
+		};
+
+		switch-hall-sensor {
+			gpios = <&gpx2 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+			label = "hall effect sensor";
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+	};
+
+	vbatt_reg: voltage-regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VBATT";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	backlight_reset_supply: voltage-regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "BACKLIGHT_ENVDDIO";
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_reset>;
+		gpio = <&gpm0 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	lcd_enable_supply: voltage-regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "LCD_VDD_2.2V";
+		regulator-min-microvolt = <2200000>;
+		regulator-max-microvolt = <2200000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_en>;
+		gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>; /* LCD_EN */
+		enable-active-high;
+	};
+
+	i2c_max77693: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		pmic@66 {
+			compatible = "maxim,max77693";
+			interrupt-parent = <&gpx1>;
+			interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&max77693_irq>;
+			reg = <0x66>;
+
+			regulators {
+				esafeout1_reg: ESAFEOUT1 {
+					regulator-name = "ESAFEOUT1";
+					regulator-boot-on;
+				};
+
+				esafeout2_reg: ESAFEOUT2 {
+					regulator-name = "ESAFEOUT2";
+				};
+
+				charger_reg: CHARGER {
+					regulator-name = "CHARGER";
+					regulator-min-microamp = <60000>;
+					regulator-max-microamp = <2580000>;
+					regulator-boot-on;
+				};
+			};
+
+			charger {
+				compatible = "maxim,max77693-charger";
+
+				maxim,constant-microvolt = <4350000>;
+				maxim,min-system-microvolt = <3600000>;
+				maxim,thermal-regulation-celsius = <100>;
+				maxim,battery-overcurrent-microamp = <3500000>;
+				maxim,charge-input-threshold-microvolt = <4300000>;
+			};
+		};
+	};
+
+	i2c_max77693_fuel: i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		fuel-gauge@36 {
+			compatible = "maxim,max17050";
+			interrupt-parent = <&gpx2>;
+			interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&max77693_fuel_irq>;
+			reg = <0x36>;
+
+			maxim,over-heat-temp = <500>;
+			maxim,over-volt = <4500>;
+		};
+	};
+
+	i2c_yas532_magnetometer: i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		/* Magnetometer: Yamaha YAS532 */
+		magnetometer@2e {
+			compatible = "yamaha,yas532";
+			reg = <0x2e>;
+			iovdd-supply = <&ldo3_reg>; /* VCC_1.8V_AP */
+			mount-matrix = "-1", "0", "0",
+					  "0", "1", "0",
+					  "0", "0", "-1";
+		};
+	};
+
+	i2c_lightsensor: i2c-gpio-4 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpl0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpl0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		/* WiFi model uses CM3323, 3G/LTE use CM36653 */
+	};
+
+	i2c_bl: i2c-gpio-24 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpm4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpm4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		backlight: backlight@2c {
+			compatible = "ti,lp8556";
+			reg = <0x2c>;
+			status = "okay";
+
+			bl-name = "lcd-bl";
+			dev-ctrl = /bits/ 8 <0x80>;
+			init-brt = /bits/ 8 <0x78>; /* 120 */
+
+			power-supply = <&vbatt_reg>;
+			enable-supply = <&backlight_reset_supply>;
+
+			pwms = <&pwm 1 78770 0>;
+			pwm-names = "lp8556";
+			pwm-period = <78770>;
+
+			rom_a3h {
+				rom-addr = /bits/ 8 <0xa3>;
+				rom-val = /bits/ 8 <0x5e>;
+			};
+
+			rom_a5h {
+				rom-addr = /bits/ 8 <0xa5>;
+				rom-val = /bits/ 8 <0x34>;
+			};
+
+			rom_a7h {
+				rom-addr = /bits/ 8 <0xa7>;
+				rom-val = /bits/ 8 <0xfa>;
+			};
+		};
+	};
+
+	wlan_pwrseq: sdhci3-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&bus_dmc {
+	devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
+	vdd-supply = <&buck1_reg>;
+	status = "okay";
+};
+
+&bus_acp {
+	devfreq = <&bus_dmc>;
+	status = "okay";
+};
+
+&bus_c2c {
+	devfreq = <&bus_dmc>;
+	status = "okay";
+};
+
+&bus_leftbus {
+	devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
+	vdd-supply = <&buck3_reg>;
+	status = "okay";
+};
+
+&bus_rightbus {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_display {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_fsys {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_peri {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&bus_mfc {
+	devfreq = <&bus_leftbus>;
+	status = "okay";
+};
+
+&cpu0 {
+	cpu0-supply = <&buck2_reg>;
+};
+
+&dsi_0 {
+	vddcore-supply = <&ldo8_reg>;
+	vddio-supply = <&ldo10_reg>;
+	samsung,burst-clock-frequency = <500000000>;
+	samsung,esc-clock-frequency = <20000000>;
+	samsung,pll-clock-frequency = <24000000>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "samsung,s6d7aa0-lsl080al02";
+		reg = <0>;
+		enable-supply = <&lcd_enable_supply>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_nrst>;
+		reset-gpios = <&gpf0 4 GPIO_ACTIVE_LOW>;
+		backlight = <&backlight>;
+	};
+};
+
+&exynos_usbphy {
+	vbus-supply = <&esafeout1_reg>;
+	status = "okay";
+};
+
+&fimd {
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&buck4_reg>;
+	status = "okay";
+};
+
+&hsotg {
+	vusb_d-supply = <&ldo15_reg>;
+	vusb_a-supply = <&ldo12_reg>;
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+/* Accelerometer: K2DH/K3DH */
+&i2c_1 {
+	pinctrl-0 = <&i2c1_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	lis3dh: accelerometer@19 {
+		/* K2DH seems to be the same as lis2dh12 in terms of registers */
+		compatible = "st,lis2dh12-accel";
+		reg = <0x19>;
+
+		interrupt-parent = <&gpx0>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+		vdd-supply = <&ldo17_reg>; /* VCC_2.8V_AP */
+		vddio-supply = <&ldo3_reg>; /* VCC_1.8V_AP */
+
+		mount-matrix = "-1", "0", "0",
+				  "0", "1", "0",
+				  "0", "0", "-1";
+	};
+};
+
+/* Touchscreen: MMS252 */
+&i2c_3 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <400000>;
+	pinctrl-0 = <&i2c3_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	touchscreen@48 {
+		/* Using mms114 compatible for now */
+		compatible = "melfas,mms114";
+		reg = <0x48>;
+		interrupt-parent = <&gpb>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <1280>;
+		avdd-supply = <&ldo21_reg>;
+		vdd-supply = <&ldo25_reg>;
+	};
+};
+
+/* PMIC: s5m8767 */
+&i2c_7 {
+	samsung,i2c-sda-delay = <100>;
+	samsung,i2c-slave-addr = <0x10>;
+	samsung,i2c-max-bus-freq = <100000>;
+	pinctrl-0 = <&i2c7_bus>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	s5m8767: pmic@66 {
+		compatible = "samsung,s5m8767-pmic";
+		reg = <0x66>;
+		interrupt-parent = <&gpx0>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
+		wakeup-source;
+
+		s5m8767,pmic-buck2-ramp-enable;
+		s5m8767,pmic-buck3-ramp-enable;
+		s5m8767,pmic-buck4-ramp-enable;
+
+		s5m8767,pmic-buck-ramp-delay = <25>;
+		s5m8767,pmic-buck-default-dvs-idx = <1>;
+
+		s5m8767,pmic-buck-dvs-gpios = <&gpm3 0 GPIO_ACTIVE_HIGH>,
+						 <&gpm3 1 GPIO_ACTIVE_HIGH>,
+						 <&gpm3 2 GPIO_ACTIVE_HIGH>;
+
+		s5m8767,pmic-buck-ds-gpios = <&gpf3 1 GPIO_ACTIVE_HIGH>,
+						 <&gpf3 2 GPIO_ACTIVE_HIGH>,
+						 <&gpf3 3 GPIO_ACTIVE_HIGH>;
+
+		s5m8767,pmic-buck2-dvs-voltage = <1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>;
+
+		s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>;
+
+		s5m8767,pmic-buck4-dvs-voltage = <1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>,
+						<1100000>, <1100000>;
+
+		regulators {
+			ldo1_reg: LDO1 {
+				regulator-name = "VALIVE_1.0V_AP";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <1>;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VM1M2_1.2V_AP";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <1>;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "VCC_1.8V_AP";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				op_mode = <1>;
+			};
+
+			ldo5_reg: LDO5 {
+				regulator-name = "VCC_3.3V_MHL";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				op_mode = <1>;
+			};
+
+			ldo8_reg: LDO8 {
+				regulator-name = "VMIPI_1.0V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				op_mode = <3>;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "VSIL_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				op_mode = <1>;
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "VMIPI_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				op_mode = <3>;
+			};
+
+			ldo12_reg: LDO12 {
+				regulator-name = "VUOTG_3.0V";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				op_mode = <1>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo13_reg: LDO13 {
+				regulator-name = "VCC_1.8V_MHL";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				op_mode = <1>;
+			};
+
+			ldo15_reg: LDO15 {
+				regulator-name = "VHSIC_1.0V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				op_mode = <1>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo17_reg: LDO17 {
+				regulator-name = "VCC_2.8V_AP";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				op_mode = <1>;
+				regulator-always-on;
+			};
+
+			ldo19_reg: LDO19 {
+				regulator-name = "VLED_IC_1.9V";
+				regulator-min-microvolt = <1900000>;
+				regulator-max-microvolt = <1900000>;
+				op_mode = <1>;
+				regulator-always-on;
+			};
+
+			ldo20_reg: LDO20 {
+				regulator-name = "VTOUCH_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				op_mode = <1>;
+			};
+
+			ldo21_reg: LDO21 {
+				regulator-name = "TSP_VDD_3.3V";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				op_mode = <1>;
+			};
+
+			ldo22_reg: LDO22 {
+				regulator-name = "5M_AF_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				op_mode = <1>;
+			};
+
+			ldo23_reg: LDO23 {
+				regulator-name = "VTF_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				op_mode = <3>;
+			};
+
+			ldo24_reg: LDO24 {
+				regulator-name = "LEDA_2.8V";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				op_mode = <1>;
+			};
+
+			ldo25_reg: LDO25 {
+				regulator-name = "TSP_VDD_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				op_mode = <1>;
+			};
+
+			ldo26_reg: LDO26 {
+				regulator-name = "CAM_IO_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				op_mode = <1>;
+			};
+
+			ldo27_reg: LDO27 {
+				regulator-name = "VTCAM_1.8V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				op_mode = <1>;
+			};
+
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_MIF";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "VDD_ARM";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "VDD_INT";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "VDD_G3D";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-boot-on;
+				op_mode = <3>;
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "VMEM_1.2V_AP";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt	= <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+				op_mode = <1>;
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "CAM_ISP_CORE_1.2V";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				op_mode = <1>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+
+		s5m8767_osc: clocks {
+			compatible = "samsung,s5m8767-clk";
+			#clock-cells = <1>;
+			clock-output-names = "en32khz_ap",
+						 "en32khz_cp",
+						 "en32khz_bt";
+		};
+	};
+};
+
+&mshc_0 {
+	broken-cd;
+	non-removable;
+	card-detect-delay = <200>;
+	vmmc-supply = <&ldo22_reg>;
+	clock-frequency = <400000000>;
+	samsung,dw-mshc-ciu-div = <0>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+	pinctrl-names = "default";
+	status = "okay";
+	bus-width = <8>;
+	cap-mmc-highspeed;
+};
+
+&pinctrl_0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep0>;
+
+	s5m8767_ds: s5m8767-ds {
+		samsung,pins = "gpf3-1", "gpf3-2", "gpf3-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	lcd_en: lcd-en {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	lcd_nrst: lcd-nrst {
+		samsung,pins = "gpf0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	sleep0: sleep-state {
+		PIN_SLP(gpa0-0, INPUT, NONE);
+		PIN_SLP(gpa0-1, OUT0, NONE);
+		PIN_SLP(gpa0-2, INPUT, NONE);
+		PIN_SLP(gpa0-3, INPUT, UP);
+		PIN_SLP(gpa0-4, INPUT, DOWN); /* UP on LTE model */
+		PIN_SLP(gpa0-5, INPUT, DOWN); /* UP on LTE model */
+		PIN_SLP(gpa0-6, INPUT, DOWN);
+		PIN_SLP(gpa0-7, INPUT, DOWN);
+
+		PIN_SLP(gpa1-0, INPUT, DOWN);
+		PIN_SLP(gpa1-1, INPUT, DOWN);
+		PIN_SLP(gpa1-2, INPUT, DOWN);
+		PIN_SLP(gpa1-3, INPUT, DOWN);
+		PIN_SLP(gpa1-4, INPUT, DOWN);
+		PIN_SLP(gpa1-5, INPUT, DOWN);
+
+		PIN_SLP(gpb-0, INPUT, NONE);
+		PIN_SLP(gpb-1, INPUT, NONE);
+		PIN_SLP(gpb-2, INPUT, NONE);
+		PIN_SLP(gpb-3, INPUT, NONE);
+		PIN_SLP(gpb-4, INPUT, DOWN);
+		PIN_SLP(gpb-5, INPUT, DOWN); /* UP on all models with modem */
+		PIN_SLP(gpb-6, INPUT, DOWN);
+		PIN_SLP(gpb-7, INPUT, DOWN);
+
+		PIN_SLP(gpc0-0, INPUT, DOWN); /* PREV, NONE on LTE model */
+		PIN_SLP(gpc0-1, INPUT, DOWN);
+		PIN_SLP(gpc0-2, INPUT, DOWN);
+		PIN_SLP(gpc0-3, INPUT, DOWN);
+		PIN_SLP(gpc0-4, INPUT, DOWN);
+
+		PIN_SLP(gpc1-0, INPUT, DOWN);
+		PIN_SLP(gpc1-1, INPUT, DOWN);
+		PIN_SLP(gpc1-2, INPUT, DOWN);
+		PIN_SLP(gpc1-3, INPUT, DOWN); /* NONE on LTE model */
+		PIN_SLP(gpc1-4, INPUT, DOWN);
+
+		PIN_SLP(gpd0-0, INPUT, DOWN);
+		PIN_SLP(gpd0-1, OUT0, NONE);
+		PIN_SLP(gpd0-2, INPUT, NONE);
+		PIN_SLP(gpd0-3, INPUT, NONE);
+
+		PIN_SLP(gpd1-0, INPUT, DOWN);
+		PIN_SLP(gpd1-1, INPUT, DOWN);
+		PIN_SLP(gpd1-2, INPUT, NONE);
+		PIN_SLP(gpd1-3, INPUT, NONE);
+
+		PIN_SLP(gpf0-0, INPUT, DOWN);
+		PIN_SLP(gpf0-1, INPUT, DOWN);
+		PIN_SLP(gpf0-2, INPUT, DOWN);
+		PIN_SLP(gpf0-3, INPUT, DOWN);
+		PIN_SLP(gpf0-4, OUT0, NONE);
+		PIN_SLP(gpf0-5, OUT0, NONE);
+		PIN_SLP(gpf0-6, INPUT, DOWN);
+		PIN_SLP(gpf0-7, INPUT, DOWN);
+
+		PIN_SLP(gpf1-0, INPUT, DOWN);
+		PIN_SLP(gpf1-1, INPUT, DOWN);
+		PIN_SLP(gpf1-2, INPUT, DOWN);
+		PIN_SLP(gpf1-3, INPUT, DOWN);
+		PIN_SLP(gpf1-4, INPUT, DOWN);
+		PIN_SLP(gpf1-5, INPUT, DOWN);
+		PIN_SLP(gpf1-6, INPUT, DOWN); /* NONE on LTE model */
+		PIN_SLP(gpf1-7, INPUT, DOWN);
+
+		PIN_SLP(gpf2-0, INPUT, DOWN);
+		PIN_SLP(gpf2-1, INPUT, DOWN);
+		PIN_SLP(gpf2-2, INPUT, DOWN); /* PREV, NONE on LTE model */
+		PIN_SLP(gpf2-3, INPUT, DOWN);
+		PIN_SLP(gpf2-4, INPUT, DOWN);
+		PIN_SLP(gpf2-5, INPUT, DOWN);
+		PIN_SLP(gpf2-6, INPUT, DOWN);
+		PIN_SLP(gpf2-7, INPUT, DOWN);
+
+		PIN_SLP(gpf3-0, INPUT, DOWN);
+		PIN_SLP(gpf3-1, INPUT, DOWN);
+		PIN_SLP(gpf3-2, INPUT, DOWN);
+		PIN_SLP(gpf3-3, INPUT, DOWN);
+		PIN_SLP(gpf3-4, PREV, NONE);
+		PIN_SLP(gpf3-5, OUT0, DOWN);
+
+		PIN_SLP(gpj0-0, INPUT, DOWN);
+		PIN_SLP(gpj0-1, INPUT, DOWN);
+		PIN_SLP(gpj0-2, INPUT, DOWN);
+		PIN_SLP(gpj0-3, OUT0, NONE);
+		PIN_SLP(gpj0-4, INPUT, DOWN);
+		PIN_SLP(gpj0-5, INPUT, DOWN);
+		PIN_SLP(gpj0-6, OUT0, NONE);
+		PIN_SLP(gpj0-7, OUT0, NONE);
+
+		PIN_SLP(gpj1-0, OUT0, NONE);
+		PIN_SLP(gpj1-1, INPUT, DOWN);
+		PIN_SLP(gpj1-2, PREV, NONE);
+		PIN_SLP(gpj1-3, INPUT, DOWN);
+		PIN_SLP(gpj1-4, INPUT, DOWN);
+	};
+};
+
+&pinctrl_1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep1>;
+
+	max77693_irq: max77693-irq {
+		samsung,pins = "gpx1-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	max77693_fuel_irq: max77693-fuel-irq {
+		samsung,pins = "gpx2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	s5m8767_dvs: s5m8767-dvs {
+		samsung,pins = "gpm3-0", "gpm3-1", "gpm3-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	s5m8767_irq: s5m8767-irq {
+		samsung,pins = "gpx0-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	sdhci2_cd: sdhci2-cd-irq {
+		samsung,pins = "gpx3-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	bt_shutdown: bt-shutdown-pins {
+		samsung,pins = "gpl0-6";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_host_wakeup: bt-host-wakeup-pins {
+		samsung,pins = "gpx2-6";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	bt_device_wakeup: bt-device-wakeup-pins {
+		samsung,pins = "gpx3-1";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	backlight_reset: backlight-reset {
+		samsung,pins = "gpm0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	gpio_keys: gpio-keys-pins {
+		samsung,pins = "gpx1-2", "gpx2-2", "gpx2-4", "gpx2-7", "gpx3-3";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	sleep1: sleep-state {
+		PIN_SLP(gpk0-0, PREV, NONE);
+		PIN_SLP(gpk0-1, PREV, NONE);
+		PIN_SLP(gpk0-2, PREV, NONE);
+		PIN_SLP(gpk0-3, PREV, NONE);
+		PIN_SLP(gpk0-4, PREV, NONE);
+		PIN_SLP(gpk0-5, PREV, NONE);
+		PIN_SLP(gpk0-6, PREV, NONE);
+
+		PIN_SLP(gpk1-0, INPUT, DOWN);
+		PIN_SLP(gpk1-1, INPUT, DOWN);
+		PIN_SLP(gpk1-2, INPUT, DOWN);
+		PIN_SLP(gpk1-3, PREV, NONE);
+		PIN_SLP(gpk1-4, PREV, NONE);
+		PIN_SLP(gpk1-5, PREV, NONE);
+		PIN_SLP(gpk1-6, PREV, NONE);
+
+		PIN_SLP(gpk2-0, INPUT, DOWN);
+		PIN_SLP(gpk2-1, INPUT, DOWN);
+		PIN_SLP(gpk2-2, INPUT, DOWN);
+		PIN_SLP(gpk2-3, INPUT, DOWN);
+		PIN_SLP(gpk2-4, INPUT, DOWN);
+		PIN_SLP(gpk2-5, INPUT, DOWN);
+		PIN_SLP(gpk2-6, INPUT, DOWN);
+
+		PIN_SLP(gpk3-0, OUT0, NONE);
+		PIN_SLP(gpk3-1, INPUT, NONE);
+		PIN_SLP(gpk3-2, INPUT, DOWN);
+		PIN_SLP(gpk3-3, INPUT, NONE);
+		PIN_SLP(gpk3-4, INPUT, NONE);
+		PIN_SLP(gpk3-5, INPUT, NONE);
+		PIN_SLP(gpk3-6, INPUT, NONE);
+
+		PIN_SLP(gpl0-0, INPUT, DOWN); /* OUT0 on 3G, PREV on LTE; NONE on both */
+		PIN_SLP(gpl0-1, INPUT, NONE);
+		PIN_SLP(gpl0-2, INPUT, NONE);
+		PIN_SLP(gpl0-3, INPUT, DOWN);
+		PIN_SLP(gpl0-4, INPUT, DOWN);
+		PIN_SLP(gpl0-6, PREV, NONE);
+
+		PIN_SLP(gpl1-0, INPUT, DOWN); /* OUT0 on 3G, PREV on LTE; NONE on both */
+		PIN_SLP(gpl1-1, OUT0, NONE);
+		PIN_SLP(gpl2-0, INPUT, DOWN);
+		PIN_SLP(gpl2-1, PREV, NONE); /* INPUT, DOWN on LTE */
+		PIN_SLP(gpl2-2, PREV, NONE); /* INPUT, DOWN on LTE */
+		PIN_SLP(gpl2-3, INPUT, DOWN);
+		PIN_SLP(gpl2-4, INPUT, DOWN); /* OUT0, NONE on models with modem */
+		PIN_SLP(gpl2-5, INPUT, DOWN); /* PREV, NONE on LTE */
+		PIN_SLP(gpl2-6, INPUT, DOWN);
+		PIN_SLP(gpl2-7, INPUT, DOWN);
+
+		PIN_SLP(gpm0-0, PREV, NONE);
+		PIN_SLP(gpm0-1, OUT0, NONE);
+		PIN_SLP(gpm0-2, INPUT, DOWN);
+		PIN_SLP(gpm0-3, INPUT, DOWN);
+		PIN_SLP(gpm0-4, INPUT, DOWN);
+		PIN_SLP(gpm0-5, INPUT, DOWN);
+		PIN_SLP(gpm0-6, INPUT, DOWN);
+		PIN_SLP(gpm0-7, INPUT, DOWN);
+
+		PIN_SLP(gpm1-0, INPUT, DOWN);
+		PIN_SLP(gpm1-1, INPUT, DOWN);
+		PIN_SLP(gpm1-2, INPUT, NONE);
+		PIN_SLP(gpm1-3, INPUT, NONE);
+		PIN_SLP(gpm1-4, INPUT, NONE);
+		PIN_SLP(gpm1-5, INPUT, NONE);
+		PIN_SLP(gpm1-6, OUT0, NONE);
+
+		PIN_SLP(gpm2-0, INPUT, NONE);
+		PIN_SLP(gpm2-1, INPUT, NONE);
+		PIN_SLP(gpm2-2, OUT0, NONE);
+		PIN_SLP(gpm2-3, INPUT, DOWN);
+		PIN_SLP(gpm2-4, INPUT, DOWN);
+
+		PIN_SLP(gpm3-0, PREV, NONE);
+		PIN_SLP(gpm3-1, PREV, NONE);
+		PIN_SLP(gpm3-2, PREV, NONE);
+		PIN_SLP(gpm3-3, INPUT, DOWN); /* OUT1, NONE for 3G */
+		PIN_SLP(gpm3-4, INPUT, DOWN);
+		PIN_SLP(gpm3-5, PREV, NONE);
+		PIN_SLP(gpm3-6, INPUT, DOWN);
+		PIN_SLP(gpm3-7, OUT0, NONE);
+
+		PIN_SLP(gpm4-0, INPUT, DOWN);
+		PIN_SLP(gpm4-1, INPUT, DOWN);
+		PIN_SLP(gpm4-2, INPUT, DOWN);
+		PIN_SLP(gpm4-3, INPUT, DOWN);
+		PIN_SLP(gpm4-4, PREV, NONE);
+		PIN_SLP(gpm4-5, INPUT, NONE);
+		PIN_SLP(gpm4-6, INPUT, DOWN);
+		PIN_SLP(gpm4-7, INPUT, DOWN);
+
+		PIN_SLP(gpy0-0, INPUT, DOWN);
+		PIN_SLP(gpy0-1, INPUT, DOWN);
+		PIN_SLP(gpy0-2, INPUT, NONE);
+		PIN_SLP(gpy0-3, INPUT, NONE);
+		PIN_SLP(gpy0-4, INPUT, DOWN);
+		PIN_SLP(gpy0-5, INPUT, DOWN);
+
+		PIN_SLP(gpy1-0, INPUT, DOWN);
+		PIN_SLP(gpy1-1, INPUT, DOWN);
+		PIN_SLP(gpy1-2, INPUT, DOWN);
+		PIN_SLP(gpy1-3, INPUT, DOWN);
+
+		PIN_SLP(gpy2-0, PREV, NONE);
+		PIN_SLP(gpy2-1, INPUT, DOWN);
+		PIN_SLP(gpy2-2, INPUT, NONE);
+		PIN_SLP(gpy2-3, INPUT, NONE);
+		PIN_SLP(gpy2-4, INPUT, NONE);
+		PIN_SLP(gpy2-5, INPUT, NONE);
+
+		PIN_SLP(gpy3-0, INPUT, DOWN);
+		PIN_SLP(gpy3-1, INPUT, DOWN);
+		PIN_SLP(gpy3-2, INPUT, DOWN);
+		PIN_SLP(gpy3-3, INPUT, DOWN);
+		PIN_SLP(gpy3-4, INPUT, DOWN);
+		PIN_SLP(gpy3-5, INPUT, DOWN);
+		PIN_SLP(gpy3-6, INPUT, DOWN);
+		PIN_SLP(gpy3-7, INPUT, DOWN);
+
+		PIN_SLP(gpy4-0, INPUT, DOWN);
+		PIN_SLP(gpy4-1, INPUT, DOWN);
+		PIN_SLP(gpy4-2, INPUT, DOWN);
+		PIN_SLP(gpy4-3, INPUT, DOWN);
+		PIN_SLP(gpy4-4, INPUT, DOWN);
+		PIN_SLP(gpy4-5, INPUT, DOWN);
+		PIN_SLP(gpy4-6, INPUT, DOWN);
+		PIN_SLP(gpy4-7, INPUT, DOWN);
+
+		PIN_SLP(gpy5-0, INPUT, DOWN);
+		PIN_SLP(gpy5-1, INPUT, DOWN);
+		PIN_SLP(gpy5-2, INPUT, DOWN);
+		PIN_SLP(gpy5-3, INPUT, DOWN);
+		PIN_SLP(gpy5-4, INPUT, DOWN);
+		PIN_SLP(gpy5-5, INPUT, DOWN);
+		PIN_SLP(gpy5-6, INPUT, DOWN);
+		PIN_SLP(gpy5-7, INPUT, DOWN);
+
+		PIN_SLP(gpy6-0, INPUT, DOWN);
+		PIN_SLP(gpy6-1, INPUT, DOWN);
+		PIN_SLP(gpy6-2, INPUT, DOWN);
+		PIN_SLP(gpy6-3, INPUT, DOWN);
+		PIN_SLP(gpy6-4, INPUT, DOWN);
+		PIN_SLP(gpy6-5, INPUT, DOWN);
+		PIN_SLP(gpy6-6, INPUT, DOWN);
+		PIN_SLP(gpy6-7, INPUT, DOWN);
+	};
+};
+
+&pinctrl_2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep2>;
+
+	sleep2: sleep-state {
+		PIN_SLP(gpz-0, INPUT, DOWN);
+		PIN_SLP(gpz-1, INPUT, DOWN);
+		PIN_SLP(gpz-2, INPUT, DOWN);
+		PIN_SLP(gpz-3, INPUT, DOWN);
+		PIN_SLP(gpz-4, INPUT, DOWN);
+		PIN_SLP(gpz-5, INPUT, DOWN);
+		PIN_SLP(gpz-6, INPUT, DOWN);
+	};
+};
+
+&pinctrl_3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sleep3>;
+
+	sleep3: sleep-state {
+		PIN_SLP(gpv0-0, INPUT, DOWN);
+		PIN_SLP(gpv0-1, INPUT, DOWN);
+		PIN_SLP(gpv0-2, INPUT, DOWN);
+		PIN_SLP(gpv0-3, INPUT, DOWN);
+		PIN_SLP(gpv0-4, INPUT, DOWN);
+		PIN_SLP(gpv0-5, INPUT, DOWN);
+		PIN_SLP(gpv0-6, INPUT, DOWN);
+		PIN_SLP(gpv0-7, INPUT, DOWN);
+
+		PIN_SLP(gpv1-0, INPUT, DOWN);
+		PIN_SLP(gpv1-1, INPUT, DOWN);
+		PIN_SLP(gpv1-2, INPUT, DOWN);
+		PIN_SLP(gpv1-3, INPUT, DOWN);
+		PIN_SLP(gpv1-4, INPUT, DOWN);
+		PIN_SLP(gpv1-5, INPUT, DOWN);
+		PIN_SLP(gpv1-6, INPUT, DOWN);
+		PIN_SLP(gpv1-7, INPUT, DOWN);
+
+		PIN_SLP(gpv2-0, INPUT, DOWN);
+		PIN_SLP(gpv2-1, INPUT, DOWN);
+		PIN_SLP(gpv2-2, INPUT, DOWN);
+		PIN_SLP(gpv2-3, INPUT, DOWN);
+		PIN_SLP(gpv2-4, INPUT, DOWN);
+		PIN_SLP(gpv2-5, INPUT, DOWN);
+		PIN_SLP(gpv2-6, INPUT, DOWN);
+		PIN_SLP(gpv2-7, INPUT, DOWN);
+
+		PIN_SLP(gpv3-0, INPUT, DOWN);
+		PIN_SLP(gpv3-1, INPUT, DOWN);
+		PIN_SLP(gpv3-2, INPUT, DOWN);
+		PIN_SLP(gpv3-3, INPUT, DOWN);
+		PIN_SLP(gpv3-4, INPUT, DOWN);
+		PIN_SLP(gpv3-5, INPUT, DOWN);
+		PIN_SLP(gpv3-6, INPUT, DOWN);
+		PIN_SLP(gpv3-7, INPUT, DOWN);
+
+		PIN_SLP(gpv4-0, INPUT, DOWN);
+		PIN_SLP(gpv4-1, INPUT, DOWN);
+	};
+};
+
+&pmu_system_controller {
+	assigned-clocks = <&pmu_system_controller 0>;
+	assigned-clock-parents = <&clock CLK_XUSBXTI>;
+};
+
+&pwm {
+	pinctrl-0 = <&pwm1_out>;
+	pinctrl-names = "default";
+	samsung,pwm-outputs = <1>;
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+	clocks = <&clock CLK_RTC>, <&s5m8767_osc S2MPS11_CLK_AP>;
+	clock-names = "rtc", "rtc_src";
+};
+
+&sdhci_2 {
+	bus-width = <4>;
+	cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>;
+	pinctrl-names = "default";
+	vmmc-supply = <&ldo23_reg>;
+	status = "okay";
+};
+
+&sdhci_3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	non-removable;
+	bus-width = <4>;
+
+	mmc-pwrseq = <&wlan_pwrseq>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
+	status = "okay";
+
+	/* BCM4334 Wi-Fi */
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupt-parent = <&gpx2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&serial_0 {
+	pinctrl-0 = <&uart0_data &uart0_fctl>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* BCM4334B0 Bluetooth */
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>;
+		pinctrl-names = "default";
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
+		clocks = <&s5m8767_osc S2MPS11_CLK_BT>;
+	};
+};
+
+&serial_1 {
+	status = "okay";
+};
+
+&serial_2 {
+	status = "okay";
+};
+
+&serial_3 {
+	status = "okay";
+};
+
+&tmu {
+	vtmu-supply = <&ldo10_reg>;
+	status = "okay";
+};