@@ -194,6 +194,7 @@ struct atomisp_device {
* Note this is indexed by mipi_port_id not atomisp_camera_port.
*/
int sensor_lanes[N_MIPI_PORT_ID];
+ struct v4l2_subdev *sensor_subdevs[ATOMISP_CAMERA_NR_PORTS];
unsigned int input_cnt;
struct atomisp_input_subdev inputs[ATOM_ISP_MAX_INPUTS];
struct v4l2_subdev *flash;
@@ -782,7 +782,7 @@ static int atomisp_subdev_probe(struct atomisp_device *isp)
{
const struct atomisp_platform_data *pdata;
struct intel_v4l2_subdev_table *subdevs;
- int ret, mipi_port, raw_index = -1, count;
+ int ret, mipi_port, count;
pdata = atomisp_get_platform_data();
if (!pdata) {
@@ -814,26 +814,20 @@ static int atomisp_subdev_probe(struct atomisp_device *isp)
switch (subdevs->type) {
case RAW_CAMERA:
- dev_dbg(isp->dev, "raw_index: %d\n", raw_index);
- raw_index = isp->input_cnt;
- if (isp->input_cnt >= ATOM_ISP_MAX_INPUTS) {
- dev_warn(isp->dev,
- "too many atomisp inputs, ignored\n");
- break;
- }
-
if (subdevs->port >= ATOMISP_CAMERA_NR_PORTS) {
dev_err(isp->dev, "port %d not supported\n", subdevs->port);
break;
}
- isp->inputs[isp->input_cnt].type = subdevs->type;
- isp->inputs[isp->input_cnt].port = subdevs->port;
- isp->inputs[isp->input_cnt].camera = subdevs->subdev;
- isp->input_cnt++;
+ if (isp->sensor_subdevs[subdevs->port]) {
+ dev_err(isp->dev, "port %d already has a sensor attached\n",
+ subdevs->port);
+ break;
+ }
mipi_port = atomisp_port_to_mipi_port(isp, subdevs->port);
isp->sensor_lanes[mipi_port] = subdevs->lanes;
+ isp->sensor_subdevs[subdevs->port] = subdevs->subdev;
break;
case CAMERA_MOTOR:
if (isp->motor) {
@@ -855,21 +849,6 @@ static int atomisp_subdev_probe(struct atomisp_device *isp)
}
}
- /*
- * HACK: Currently VCM belongs to primary sensor only, but correct
- * approach must be to acquire from platform code which sensor
- * owns it.
- */
- if (isp->motor && raw_index >= 0)
- isp->inputs[raw_index].motor = isp->motor;
-
- /* Proceed even if no modules detected. For COS mode and no modules. */
- if (!isp->input_cnt)
- dev_warn(isp->dev, "no camera attached or fail to detect\n");
- else
- dev_info(isp->dev, "detected %d camera sensors\n",
- isp->input_cnt);
-
return atomisp_csi_lane_config(isp);
}
@@ -943,16 +922,6 @@ static int atomisp_register_entities(struct atomisp_device *isp)
goto subdev_register_failed;
}
- if (isp->input_cnt < ATOM_ISP_MAX_INPUTS) {
- dev_dbg(isp->dev,
- "TPG detected, camera_cnt: %d\n", isp->input_cnt);
- isp->inputs[isp->input_cnt].type = TEST_PATTERN;
- isp->inputs[isp->input_cnt].port = -1;
- isp->inputs[isp->input_cnt++].camera = &isp->tpg.sd;
- } else {
- dev_warn(isp->dev, "too many atomisp inputs, TPG ignored.\n");
- }
-
return 0;
subdev_register_failed:
@@ -970,7 +939,43 @@ static int atomisp_register_entities(struct atomisp_device *isp)
static int atomisp_register_device_nodes(struct atomisp_device *isp)
{
- int err;
+ struct atomisp_input_subdev *input;
+ int i, err;
+
+ for (i = 0; i < ATOMISP_CAMERA_NR_PORTS; i++) {
+ if (!isp->sensor_subdevs[i])
+ continue;
+
+ input = &isp->inputs[isp->input_cnt];
+
+ input->type = RAW_CAMERA;
+ input->port = i;
+ input->camera = isp->sensor_subdevs[i];
+
+ /*
+ * HACK: Currently VCM belongs to primary sensor only, but correct
+ * approach must be to acquire from platform code which sensor
+ * owns it.
+ */
+ if (i == ATOMISP_CAMERA_PORT_PRIMARY)
+ input->motor = isp->motor;
+
+ isp->input_cnt++;
+ }
+
+ if (!isp->input_cnt)
+ dev_warn(isp->dev, "no camera attached or fail to detect\n");
+ else
+ dev_info(isp->dev, "detected %d camera sensors\n", isp->input_cnt);
+
+ if (isp->input_cnt < ATOM_ISP_MAX_INPUTS) {
+ dev_dbg(isp->dev, "TPG detected, camera_cnt: %d\n", isp->input_cnt);
+ isp->inputs[isp->input_cnt].type = TEST_PATTERN;
+ isp->inputs[isp->input_cnt].port = -1;
+ isp->inputs[isp->input_cnt++].camera = &isp->tpg.sd;
+ } else {
+ dev_warn(isp->dev, "too many atomisp inputs, TPG ignored.\n");
+ }
isp->asd.video_out.vdev.v4l2_dev = &isp->v4l2_dev;
isp->asd.video_out.vdev.device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING;
Delay mapping sensors to inputs till atomisp_register_device_nodes() time. There are 2 reasons for this: 1. This guarantees a stable input order independent of the sensor probe order. 2. This is a preparation patch for v4l2-async sensor probing support. Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- .../media/atomisp/pci/atomisp_internal.h | 1 + .../staging/media/atomisp/pci/atomisp_v4l2.c | 83 ++++++++++--------- 2 files changed, 45 insertions(+), 39 deletions(-)