diff mbox series

[3/3] iio: light: bd27008: Support BD27010 RGB

Message ID 327fde7f6e5e76908af474de3e348fe7626f39b2.1686651445.git.mazziesaccount@gmail.com
State New
Headers show
Series Support ROHM BU27010 RGBC sensor | expand

Commit Message

Matti Vaittinen June 13, 2023, 10:20 a.m. UTC
The ROHM BU27010 is an RGBC sensor with a flickering detection FIFO. The
RGBC+IR sensor functionality is largely similar to what the BU27008 has.
There are some notable things though:
  - gain setting is once again new and exotic. Now, there is 6bit gain
    setting where 4 of the bits are common to all channels and 2 bits
    can be configured separately for each channel. The BU27010 has
    similar "1X on other channels vs 2X on IR when selector is 0x0"
    gain design as BU27008 had. So, we use same gain setting policy for
    BU27010 as we did for BU27008 - driver sets same gain selector for all
    channels but shows the gains separately for all channels so users
    can (at least in theory) detect this 1X vs 2X madness...
  - BU27010 has suffled all the control register bitfields to new
    addresses and bit positions while still keeping the register naming
    same.
  - Some more power/reset control is added.
  - FIFO for "flickering detection" is added.

The control register suffling made this slightly nasty. Still, it is
easier for maintenance perspective to add the BU27010 support in BU27008
driver because - even though the bit positions/addresses were changed -
most of the driver structure can be re-used. Writing own driver for
BU27010 would mean plenty of duplicate code albeit a tad more clarity.

The flickering FIFO is not supported by the driver.

Add BU27010 RGBC+IR support to rohm-bu27008 driver.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>

---
This is my 4.th re-write. My first idea was to write separate drivers
for the BU27008 and BU27010. I abandoned this as I ended up copying most
of the functions and just changing some of the bit offsets / register
addresses. This felt like a plenty of copy-paste.

So, 2.nd attempt was to combine BU27008 and BU27010. I hit the wall
as I tried to support setting RGBC / IR gains independently for BU27008
and setting the gain independently for each channel on BU27010 when
gains were such that the HW could support them independently. This went
to complete madness.

This is when I asked for a second opinion - which was to clear the mess
by separating the BU27008 and BU27010 in own drivers. After a while it
become obvious that supporting independet gains for the channels when HW
supported it required decisions which could not predictably be done for
all users. There is a comment explaining some of this in
bu27008_write_gain_sel().

After the complexity of shared gain bits was killed, the two separate
drivers started to look like a copy-paste again - and all the bugs had
to be fixed in two places... As a result I again pulled it all in one
driver. As a result of this experimenting, I firmly believe supporting
both ICs in the same driver is a correct design.
---
 drivers/iio/light/rohm-bu27008.c | 325 ++++++++++++++++++++++++++++++-
 1 file changed, 315 insertions(+), 10 deletions(-)
diff mbox series

Patch

diff --git a/drivers/iio/light/rohm-bu27008.c b/drivers/iio/light/rohm-bu27008.c
index 8c7f6f20a523..ed14fd9397e8 100644
--- a/drivers/iio/light/rohm-bu27008.c
+++ b/drivers/iio/light/rohm-bu27008.c
@@ -1,6 +1,8 @@ 
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * BU27008 ROHM Colour Sensor
+ * ROHM Colour Sensor driver for
+ * - BU27008 RGBC sensor
+ * - BU27010 RGBC + Flickering sensor
  *
  * Copyright (c) 2023, ROHM Semiconductor.
  */
@@ -22,6 +24,25 @@ 
 #include <linux/iio/trigger_consumer.h>
 #include <linux/iio/triggered_buffer.h>
 
+/*
+ * A word about register address and mask definitions.
+ *
+ * At a quick glance to the data-sheet register tables, the BU27010 has all the
+ * registers that the BU27008 has. On top of that the BU27010 adds couple of new
+ * ones.
+ *
+ * So, all definitions BU27008_REG_* are there also for BU27010 but none of the
+ * BU27010_REG_* are present on BU27008. This makes sense as BU27010 just adds
+ * some features (Flicker FIFO, more power control) on top of the BU27008.
+ *
+ * Unfortunately, some of the wheel has been re-invented. Even though the names
+ * of the registers have stayed the same, pretty much all of the functionality
+ * provided by the registers has changed place. Contents of all MODE_CONTROL
+ * registers on BU27008 and BU27010 are different.
+ *
+ * Chip-specific mapping from register addresses/bits to functionality is done
+ * in bu27_chip_data structures.
+ */
 #define BU27008_REG_SYSTEM_CONTROL	0x40
 #define BU27008_MASK_SW_RESET		BIT(7)
 #define BU27008_MASK_PART_ID		GENMASK(5, 0)
@@ -52,6 +73,56 @@ 
 #define BU27008_REG_MANUFACTURER_ID	0x92
 #define BU27008_REG_MAX BU27008_REG_MANUFACTURER_ID
 
+/* BU27010 specific definitions */
+
+#define BU27010_MASK_SW_RESET		BIT(7)
+#define BU27010_ID			0x1b
+#define BU27010_REG_POWER		0x3e
+#define BU27010_MASK_POWER		BIT(0)
+
+#define BU27010_REG_RESET		0x3f
+#define BU27010_MASK_RESET		BIT(0)
+#define BU27010_RESET_RELEASE		BU27010_MASK_RESET
+
+#define BU27010_MASK_MEAS_EN		BIT(1)
+
+#define BU27010_MASK_CHAN_SEL		GENMASK(7, 6)
+#define BU27010_MASK_MEAS_MODE		GENMASK(5, 4)
+#define BU27010_MASK_RGBC_GAIN		GENMASK(3, 0)
+
+#define BU27010_MASK_DATA3_GAIN		GENMASK(7, 6)
+#define BU27010_MASK_DATA2_GAIN		GENMASK(5, 4)
+#define BU27010_MASK_DATA1_GAIN		GENMASK(3, 2)
+#define BU27010_MASK_DATA0_GAIN		GENMASK(1, 0)
+
+#define BU27010_MASK_FLC_MODE		BIT(7)
+#define BU27010_MASK_FLC_GAIN		GENMASK(4, 0)
+
+#define BU27010_REG_MODE_CONTROL4	0x44
+/* If flicker is ever to be supported the IRQ must be handled as a field */
+#define BU27010_IRQ_DIS_ALL		GENMASK(1, 0)
+#define BU27010_DRDY_EN			BIT(0)
+#define BU27010_MASK_INT_SEL		GENMASK(1, 0)
+
+#define BU27010_REG_MODE_CONTROL5	0x45
+#define BU27010_MASK_RGB_VALID		BIT(7)
+#define BU27010_MASK_FLC_VALID		BIT(6)
+#define BU27010_MASK_WAIT_EN		BIT(3)
+#define BU27010_MASK_FIFO_EN		BIT(2)
+#define BU27010_MASK_RGB_EN		BIT(1)
+#define BU27010_MASK_FLC_EN		BIT(0)
+
+#define BU27010_REG_DATA_FLICKER_LO	0x56
+#define BU27010_MASK_DATA_FLICKER_HI	GENMASK(2, 0)
+#define BU27010_REG_FLICKER_COUNT	0x5a
+#define BU27010_REG_FIFO_LEVEL_LO	0x5b
+#define BU27010_MASK_FIFO_LEVEL_HI	BIT(0)
+#define BU27010_REG_FIFO_DATA_LO	0x5d
+#define BU27010_REG_FIFO_DATA_HI	0x5e
+#define BU27010_MASK_FIFO_DATA_HI	GENMASK(2, 0)
+#define BU27010_REG_MANUFACTURER_ID	0x92
+#define BU27010_REG_MAX BU27010_REG_MANUFACTURER_ID
+
 /**
  * enum bu27008_chan_type - BU27008 channel types
  * @BU27008_RED:	Red channel. Always via data0.
@@ -117,6 +188,17 @@  static const unsigned long bu27008_scan_masks[] = {
  */
 #define BU27008_SCALE_1X 16
 
+/*
+ * On BU27010 available scales with gain 1x - 4096x,
+ * timings 55, 100, 200, 400 mS. Time impacts to gain: 1x, 2x, 4x, 8x.
+ *
+ * => Max total gain is HWGAIN * gain by integration time (8 * 4096)
+ *
+ * Using NANO precision for scale we must use scale 64x corresponding gain 1x
+ * to avoid precision loss.
+ */
+#define BU27010_SCALE_1X 64
+
 /* See the data sheet for the "Gain Setting" table */
 #define BU27008_GSEL_1X		0x00
 #define BU27008_GSEL_4X		0x08
@@ -152,10 +234,44 @@  static const struct iio_gain_sel_pair bu27008_gains_ir[] = {
 	GAIN_SCALE_GAIN(1024, BU27008_GSEL_1024X),
 };
 
+#define BU27010_GSEL_1X		0x00	/* 000000 */
+#define BU27010_GSEL_4X		0x08	/* 001000 */
+#define BU27010_GSEL_16X	0x09	/* 001001 */
+#define BU27010_GSEL_64X	0x0e	/* 001110 */
+#define BU27010_GSEL_256X	0x1e	/* 011110 */
+#define BU27010_GSEL_1024X	0x2e	/* 101110 */
+#define BU27010_GSEL_4096X	0x3f	/* 111111 */
+
+static const struct iio_gain_sel_pair bu27010_gains[] = {
+	GAIN_SCALE_GAIN(1, BU27010_GSEL_1X),
+	GAIN_SCALE_GAIN(4, BU27010_GSEL_4X),
+	GAIN_SCALE_GAIN(16, BU27010_GSEL_16X),
+	GAIN_SCALE_GAIN(64, BU27010_GSEL_64X),
+	GAIN_SCALE_GAIN(256, BU27010_GSEL_256X),
+	GAIN_SCALE_GAIN(1024, BU27010_GSEL_1024X),
+	GAIN_SCALE_GAIN(4096, BU27010_GSEL_4096X),
+};
+
+static const struct iio_gain_sel_pair bu27010_gains_ir[] = {
+	GAIN_SCALE_GAIN(2, BU27010_GSEL_1X),
+	GAIN_SCALE_GAIN(4, BU27010_GSEL_4X),
+	GAIN_SCALE_GAIN(16, BU27010_GSEL_16X),
+	GAIN_SCALE_GAIN(64, BU27010_GSEL_64X),
+	GAIN_SCALE_GAIN(256, BU27010_GSEL_256X),
+	GAIN_SCALE_GAIN(1024, BU27010_GSEL_1024X),
+	GAIN_SCALE_GAIN(4096, BU27010_GSEL_4096X),
+};
+
 #define BU27008_MEAS_MODE_100MS		0x00
 #define BU27008_MEAS_MODE_55MS		0x01
 #define BU27008_MEAS_MODE_200MS		0x02
 #define BU27008_MEAS_MODE_400MS		0x04
+
+#define BU27010_MEAS_MODE_100MS		0x00
+#define BU27010_MEAS_MODE_55MS		0x03
+#define BU27010_MEAS_MODE_200MS		0x01
+#define BU27010_MEAS_MODE_400MS		0x02
+
 #define BU27008_MEAS_TIME_MAX_MS	400
 
 static const struct iio_itime_sel_mul bu27008_itimes[] = {
@@ -165,6 +281,13 @@  static const struct iio_itime_sel_mul bu27008_itimes[] = {
 	GAIN_SCALE_ITIME_US(55000, BU27008_MEAS_MODE_55MS, 1),
 };
 
+static const struct iio_itime_sel_mul bu27010_itimes[] = {
+	GAIN_SCALE_ITIME_US(400000, BU27010_MEAS_MODE_400MS, 8),
+	GAIN_SCALE_ITIME_US(200000, BU27010_MEAS_MODE_200MS, 4),
+	GAIN_SCALE_ITIME_US(100000, BU27010_MEAS_MODE_100MS, 2),
+	GAIN_SCALE_ITIME_US(55000, BU27010_MEAS_MODE_55MS, 1),
+};
+
 /*
  * All the RGBC channels share the same gain.
  * IR gain can be fine-tuned from the gain set for the RGBC by 2 bit, but this
@@ -221,8 +344,10 @@  struct bu27_chip_data {
 	const struct regmap_config *regmap_cfg;
 	const struct iio_gain_sel_pair *gains;
 	const struct iio_gain_sel_pair *gains_ir;
+	const struct iio_itime_sel_mul *itimes;
 	int num_gains;
 	int num_gains_ir;
+	int num_itimes;
 	int scale1x;
 
 	int drdy_en_reg;
@@ -266,11 +391,29 @@  static const struct regmap_range bu27008_volatile_ranges[] = {
 	},
 };
 
+static const struct regmap_range bu27010_volatile_ranges[] = {
+	{
+		.range_min = BU27010_REG_RESET,			/* RSTB */
+		.range_max = BU27008_REG_SYSTEM_CONTROL,	/* RESET */
+	}, {
+		.range_min = BU27010_REG_MODE_CONTROL5,		/* VALID bits */
+		.range_max = BU27010_REG_MODE_CONTROL5,
+	}, {
+		.range_min = BU27008_REG_DATA0_LO,
+		.range_max = BU27010_REG_FIFO_DATA_HI,
+	},
+};
+
 static const struct regmap_access_table bu27008_volatile_regs = {
 	.yes_ranges = &bu27008_volatile_ranges[0],
 	.n_yes_ranges = ARRAY_SIZE(bu27008_volatile_ranges),
 };
 
+static const struct regmap_access_table bu27010_volatile_regs = {
+	.yes_ranges = &bu27010_volatile_ranges[0],
+	.n_yes_ranges = ARRAY_SIZE(bu27010_volatile_ranges),
+};
+
 static const struct regmap_range bu27008_read_only_ranges[] = {
 	{
 		.range_min = BU27008_REG_DATA0_LO,
@@ -281,11 +424,26 @@  static const struct regmap_range bu27008_read_only_ranges[] = {
 	},
 };
 
+static const struct regmap_range bu27010_read_only_ranges[] = {
+	{
+		.range_min = BU27008_REG_DATA0_LO,
+		.range_max = BU27010_REG_FIFO_DATA_HI,
+	}, {
+		.range_min = BU27010_REG_MANUFACTURER_ID,
+		.range_max = BU27010_REG_MANUFACTURER_ID,
+	}
+};
+
 static const struct regmap_access_table bu27008_ro_regs = {
 	.no_ranges = &bu27008_read_only_ranges[0],
 	.n_no_ranges = ARRAY_SIZE(bu27008_read_only_ranges),
 };
 
+static const struct regmap_access_table bu27010_ro_regs = {
+	.no_ranges = &bu27010_read_only_ranges[0],
+	.n_no_ranges = ARRAY_SIZE(bu27010_read_only_ranges),
+};
+
 static const struct regmap_config bu27008_regmap = {
 	.reg_bits = 8,
 	.val_bits = 8,
@@ -308,10 +466,49 @@  static const struct regmap_config bu27008_regmap = {
 	.disable_locking = true,
 };
 
+static const struct regmap_config bu27010_regmap = {
+	.reg_bits	= 8,
+	.val_bits	= 8,
+
+	.max_register	= BU27010_REG_MAX,
+	.cache_type	= REGCACHE_RBTREE,
+	.volatile_table = &bu27010_volatile_regs,
+	.wr_table	= &bu27010_ro_regs,
+	.disable_locking = true,
+};
+
 static int bu27008_chip_init(struct bu27008_data *data);
 static int bu27008_write_gain_sel(struct bu27008_data *data, int sel);
 static int bu27008_get_gain_sel(struct bu27008_data *data, int *sel);
 
+static int bu27010_chip_init(struct bu27008_data *data);
+static int bu27010_get_gain_sel(struct bu27008_data *data, int *sel);
+static int bu27010_write_gain_sel(struct bu27008_data *data, int sel);
+
+static const struct bu27_chip_data bu27010_chip = {
+	.name = "bu27010",
+	.chip_init = bu27010_chip_init,
+	.get_gain_sel = bu27010_get_gain_sel,
+	.write_gain_sel = bu27010_write_gain_sel,
+	.scale1x = BU27010_SCALE_1X,
+	.part_id = BU27010_ID,
+	.regmap_cfg = &bu27010_regmap,
+	.drdy_en_reg = BU27010_REG_MODE_CONTROL4,
+	.drdy_en_mask = BU27010_DRDY_EN,
+	.valid_reg = BU27010_REG_MODE_CONTROL5,
+	.meas_en_reg = BU27010_REG_MODE_CONTROL5,
+	.meas_en_mask = BU27010_MASK_MEAS_EN,
+	.chan_sel_reg = BU27008_REG_MODE_CONTROL1,
+	.chan_sel_mask = BU27010_MASK_CHAN_SEL,
+	.int_time_mask = BU27010_MASK_MEAS_MODE,
+	.gains = &bu27010_gains[0],
+	.num_gains = ARRAY_SIZE(bu27010_gains),
+	.gains_ir = &bu27010_gains_ir[0],
+	.num_gains_ir = ARRAY_SIZE(bu27010_gains_ir),
+	.itimes = &bu27010_itimes[0],
+	.num_itimes = ARRAY_SIZE(bu27010_itimes),
+};
+
 static const struct bu27_chip_data bu27008_chip = {
 	.name = "bu27008",
 	.chip_init = bu27008_chip_init,
@@ -332,6 +529,8 @@  static const struct bu27_chip_data bu27008_chip = {
 	.num_gains = ARRAY_SIZE(bu27008_gains),
 	.gains_ir = &bu27008_gains_ir[0],
 	.num_gains_ir = ARRAY_SIZE(bu27008_gains_ir),
+	.itimes = &bu27008_itimes[0],
+	.num_itimes = ARRAY_SIZE(bu27008_itimes),
 };
 
 #define BU27008_MAX_VALID_RESULT_WAIT_US	50000
@@ -358,6 +557,31 @@  static int bu27008_chan_read_data(struct bu27008_data *data, int reg, int *val)
 	return ret;
 }
 
+static int bu27010_get_gain_sel(struct bu27008_data *data, int *sel)
+{
+	int ret;
+
+	/*
+	 * We always "lock" the gain selectors for all channels to prevent
+	 * unsupported configs. It does not matter which channel is used
+	 * we can just return selector from any of them.
+	 */
+	ret = regmap_read(data->regmap, BU27008_REG_MODE_CONTROL2, sel);
+	if (!ret) {
+		int tmp;
+
+		*sel = FIELD_GET(BU27010_MASK_DATA0_GAIN, *sel);
+
+		ret = regmap_read(data->regmap, BU27008_REG_MODE_CONTROL1, &tmp);
+		if (ret)
+			return ret;
+
+		*sel |= FIELD_GET(BU27010_MASK_RGBC_GAIN, tmp) << fls(BU27010_MASK_DATA0_GAIN);
+	}
+
+	return ret;
+}
+
 static int bu27008_get_gain_sel(struct bu27008_data *data, int *sel)
 {
 	int ret;
@@ -388,7 +612,7 @@  static int bu27008_get_gain(struct bu27008_data *data, struct iio_gts *gts, int
 {
 	int ret, sel;
 
-	ret = bu27008_get_gain_sel(data, &sel);
+	ret = data->cd->get_gain_sel(data, &sel);
 	if (ret)
 		return ret;
 
@@ -403,6 +627,35 @@  static int bu27008_get_gain(struct bu27008_data *data, struct iio_gts *gts, int
 	return 0;
 }
 
+static int bu27010_write_gain_sel(struct bu27008_data *data, int sel)
+{
+	unsigned int regval;
+	int ret;
+
+	/*
+	 * Gain 'selector' is composed of two registers. Selector is 6bit value,
+	 * 4 high bits being the RGBC gain fieild in MODE_CONTROL1 register and
+	 * two low bits being the channel specific gain in MODE_CONTROL2.
+	 *
+	 * Let's take the 4 high bits of whole 6 bit selector, and prepare
+	 * the MODE_CONTROL1 value (RGBC gain part).
+	 */
+	regval = FIELD_PREP(BU27010_MASK_RGBC_GAIN, (sel >> 2));
+
+	ret = regmap_update_bits(data->regmap, BU27008_REG_MODE_CONTROL1,
+				  BU27010_MASK_RGBC_GAIN, regval);
+	/*
+	 * Two low two bits must be set for all 4 channels in the
+	 * MODE_CONTROL2 register. Copy these two bits for all channels.
+	 */
+	regval = sel & GENMASK(1, 0);
+	regval = regval | regval >> 2 | regval >> 4 | regval >> 6;
+
+	ret = regmap_write(data->regmap, BU27008_REG_MODE_CONTROL2, regval);
+
+	return ret;
+}
+
 static int bu27008_write_gain_sel(struct bu27008_data *data, int sel)
 {
 	int regval;
@@ -452,7 +705,7 @@  static int bu27008_set_gain(struct bu27008_data *data, int gain)
 	if (ret < 0)
 		return ret;
 
-	return bu27008_write_gain_sel(data, ret);
+	return data->cd->write_gain_sel(data, ret);
 }
 
 static int bu27008_get_int_time_sel(struct bu27008_data *data, int *sel)
@@ -460,13 +713,15 @@  static int bu27008_get_int_time_sel(struct bu27008_data *data, int *sel)
 	int ret, val;
 
 	ret = regmap_read(data->regmap, BU27008_REG_MODE_CONTROL1, &val);
+	if (ret)
+		return ret;
 
 	val &= data->cd->int_time_mask;
 	val >>= ffs(data->cd->int_time_mask) - 1;
 
 	*sel = val;
 
-	return ret;
+	return 0;
 }
 
 static int bu27008_set_int_time_sel(struct bu27008_data *data, int sel)
@@ -759,7 +1014,7 @@  static int bu27008_set_scale(struct bu27008_data *data,
 			goto unlock_out;
 
 	}
-	ret = bu27008_write_gain_sel(data, gain_sel);
+	ret = data->cd->write_gain_sel(data, gain_sel);
 
 unlock_out:
 	mutex_unlock(&data->mutex);
@@ -867,6 +1122,55 @@  static const struct iio_info bu27008_info = {
 	.validate_trigger = iio_validate_own_trigger,
 };
 
+static int bu27010_chip_init(struct bu27008_data *data)
+{
+	int ret;
+
+	/* Reset the IC to initial power-off state */
+	ret = regmap_write_bits(data->regmap, BU27008_REG_SYSTEM_CONTROL,
+				BU27010_MASK_SW_RESET, BU27010_MASK_SW_RESET);
+	if (ret)
+		return dev_err_probe(data->dev, ret, "Sensor reset failed\n");
+
+	msleep(1);
+
+	/* Power ON*/
+	ret = regmap_write_bits(data->regmap, BU27010_REG_POWER,
+				BU27010_MASK_POWER, BU27010_MASK_POWER);
+	if (ret)
+		return dev_err_probe(data->dev, ret, "Sensor power-on failed\n");
+
+	msleep(1);
+
+	/* Release blocks from reset */
+	ret = regmap_write_bits(data->regmap, BU27010_REG_RESET,
+				BU27010_MASK_RESET, BU27010_RESET_RELEASE);
+	if (ret)
+		return dev_err_probe(data->dev, ret, "Sensor powering failed\n");
+
+	msleep(1);
+
+	/*
+	 * The IRQ enabling on BU27010 is done in a peculiar way. The IRQ
+	 * enabling is not a bit mask where individual IRQs could be enabled but
+	 * a field which values are:
+	 * 00 => IRQs disabled
+	 * 01 => Data-ready (RGBC/IR)
+	 * 10 => Data-ready (flicker)
+	 * 11 => Flicker FIFO
+	 *
+	 * So, only one IRQ can be enabled at a time and enabling for example
+	 * flicker FIFO would automagically disable data-ready IRQ.
+	 *
+	 * Currently the driver does not support the flicker. Hence, we can
+	 * just treat the RGBC data-ready as single bit which can be enabled /
+	 * disabled. This works for as long as the second bit in the field
+	 * stays zero. Here we ensure it gets zeroed.
+	 */
+	return regmap_clear_bits(data->regmap, BU27010_REG_MODE_CONTROL4,
+				 BU27010_IRQ_DIS_ALL);
+}
+
 static int bu27008_chip_init(struct bu27008_data *data)
 {
 	int ret;
@@ -1068,14 +1372,14 @@  static int bu27008_probe(struct i2c_client *i2c)
 		dev_warn(dev, "unknown device 0x%x\n", part_id);
 
 	ret = devm_iio_init_iio_gts(dev, data->cd->scale1x, 0, data->cd->gains,
-				    data->cd->num_gains, bu27008_itimes,
-				    ARRAY_SIZE(bu27008_itimes), &data->gts);
+				    data->cd->num_gains, data->cd->itimes,
+				    data->cd->num_itimes, &data->gts);
 	if (ret)
 		return ret;
 
 	ret = devm_iio_init_iio_gts(dev, data->cd->scale1x, 0, data->cd->gains_ir,
-				    data->cd->num_gains_ir, bu27008_itimes,
-				    ARRAY_SIZE(bu27008_itimes), &data->gts_ir);
+				    data->cd->num_gains_ir, data->cd->itimes,
+				    data->cd->num_itimes, &data->gts_ir);
 	if (ret)
 		return ret;
 
@@ -1113,6 +1417,7 @@  static int bu27008_probe(struct i2c_client *i2c)
 
 static const struct of_device_id bu27008_of_match[] = {
 	{ .compatible = "rohm,bu27008", .data = &bu27008_chip },
+	{ .compatible = "rohm,bu27010", .data = &bu27010_chip },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, bu27008_of_match);
@@ -1127,7 +1432,7 @@  static struct i2c_driver bu27008_i2c_driver = {
 };
 module_i2c_driver(bu27008_i2c_driver);
 
-MODULE_DESCRIPTION("ROHM BU27008 colour sensor driver");
+MODULE_DESCRIPTION("ROHM BU27008 and BU27010 colour sensor driver");
 MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
 MODULE_LICENSE("GPL");
 MODULE_IMPORT_NS(IIO_GTS_HELPER);