diff mbox series

[v2,3/3] arm64: dts: freescale: introduce rve-gateway board

Message ID 20231101183549.2960083-4-hugo@hugovil.com
State Superseded
Headers show
Series board: imx8mn-rve-gateway: add support for RVE gateway board | expand

Commit Message

Hugo Villeneuve Nov. 1, 2023, 6:35 p.m. UTC
From: Hugo Villeneuve <hvilleneuve@dimonoff.com>

The RVE gateway board is based on a Variscite VAR-SOM-NANO,
with a NXP MX8MN nano CPU.

Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
---
 MAINTAINERS                                   |   7 +
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../boot/dts/freescale/imx8mn-rve-gateway.dts | 284 ++++++++++++++++++
 3 files changed, 292 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts

Comments

Krzysztof Kozlowski Nov. 2, 2023, 7:36 a.m. UTC | #1
On 01/11/2023 19:35, Hugo Villeneuve wrote:
> From: Hugo Villeneuve <hvilleneuve@dimonoff.com>
> 
> The RVE gateway board is based on a Variscite VAR-SOM-NANO,
> with a NXP MX8MN nano CPU.
> 
> Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
> ---
>  MAINTAINERS                                   |   7 +
>  arch/arm64/boot/dts/freescale/Makefile        |   1 +
>  .../boot/dts/freescale/imx8mn-rve-gateway.dts | 284 ++++++++++++++++++
>  3 files changed, 292 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 43c5ed3c4508..9423b1bf35fc 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -18778,6 +18778,13 @@ F:	samples/rust/
>  F:	scripts/*rust*
>  K:	\b(?i:rust)\b
>  
> +RVE BOARD SUPPORT
> +M:	Hugo Villeneuve <hvilleneuve@dimonoff.com>
> +L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
> +S:	Supported
> +W:	https://rve.ca
> +F:	arch/arm64/boot/dts/freescale/imx*rve-*.dts*

I still don't think individual boards should receive maintainer entry.
https://lore.kernel.org/all/20210809080204.8381-1-shawnguo@kernel.org/

> +
>  RXRPC SOCKETS (AF_RXRPC)
>  M:	David Howells <dhowells@redhat.com>
>  M:	Marc Dionne <marc.dionne@auristor.com>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 89aee6c92576..760a0ca7adc3 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -89,6 +89,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2pro.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr3l-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mn-rve-gateway.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts b/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
> new file mode 100644
> index 000000000000..312718982a52
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
> @@ -0,0 +1,284 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright 2023 DimOnOff
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/usb/pd.h>
> +#include "imx8mn-var-som.dtsi"
> +
> +/ {
> +	model = "RVE gateway";
> +	compatible = "rve,rve-gateway", "fsl,imx8mn";

Missing compatible of SoM.

> +
> +	crystal_duart_24m: crystal-duart-24m {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <24000000>;
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpio_keys>;
> +		status = "okay";

Drop

> +
> +		key-enter {
> +			label = "enter";
> +			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_ENTER>;
> +		};
> +
> +		key-exit {
> +			label = "exit";
> +			gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_ESC>;
> +		};
> +	};
> +
> +	lcd {
> +		compatible = "hit,hd44780";
> +		display-height-chars = <2>;
> +		display-width-chars = <20>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_lcd>;
> +		data-gpios =
> +			<&gpio5  1 GPIO_ACTIVE_HIGH>,

This should be after =, with the reset of lines properly aligned.

> +			<&gpio1  6 GPIO_ACTIVE_HIGH>,
> +			<&gpio1 14 GPIO_ACTIVE_HIGH>,
> +			<&gpio4 28 GPIO_ACTIVE_HIGH>,
> +			<&gpio5 24 GPIO_ACTIVE_HIGH>,
> +			<&gpio5  2 GPIO_ACTIVE_HIGH>,
> +			<&gpio1 12 GPIO_ACTIVE_HIGH>,
> +			<&gpio5 25 GPIO_ACTIVE_HIGH>;
> +		enable-gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>;
> +		rs-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> +		rw-gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3P3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-always-on;
> +		};

Fix indentation.

> +
> +	rotary: rotary-encoder { /* Bourns PEC12R rotary encoder, 24 steps. */

No comments after {. Put them in line before or after. This applies to
other places as well.

> +		compatible = "rotary-encoder";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_rotary>;
> +		gpios =
> +			<&gpio1  5 GPIO_ACTIVE_LOW>, /* A */

This should be after =, with the reset of lines properly aligned.


> +			<&gpio3 21 GPIO_ACTIVE_LOW>; /* B */
> +		linux,axis = <0>; /* REL_X */
> +		rotary-encoder,encoding = "gray";
> +		rotary-encoder,relative-axis;
> +	};
> +};
> +
> +&ecspi1 {
> +	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
> +
> +	duart1: serial@0 {
> +		compatible = "nxp,sc16is752";
> +		reg = <0>;
> +		spi-rx-bus-width = <1>;
> +		spi-tx-bus-width = <1>;
> +		spi-max-frequency = <4000000>;
> +		clocks = <&crystal_duart_24m>;
> +		interrupt-parent = <&gpio3>;
> +		interrupts = <22 IRQ_TYPE_EDGE_FALLING>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		gpio-line-names = "RADIO0", "RADIO1", "RADIO2", "RADIO3",
> +		"RADIO4", "RADIO_RESET", "TP12", "TP11";
> +		linux,rs485-enabled-at-boot-time;
> +		rs485-rts-active-low;
> +	};
> +
> +	/delete-node/ touchscreen@0;
> +};
> +
> +&ecspi2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi2>;
> +	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> +	/delete-property/ dmas;
> +	/delete-property/ dma-names;
> +	status = "okay";
> +
> +	duart2: serial@0 {
> +		compatible = "nxp,sc16is752";
> +		reg = <0>;
> +		spi-rx-bus-width = <1>;
> +		spi-tx-bus-width = <1>;
> +		spi-max-frequency = <4000000>;
> +		clocks = <&crystal_duart_24m>;
> +		interrupt-parent = <&gpio3>;
> +		interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		gpio-line-names = "LED_B_USER", "LED_R_USER", "LED_G_USER",
> +		"GPIO_EXT3", "GPIO_EXT2", "GPIO_EXT1", "GPIO_EXT0", "TP13";
> +		linux,rs485-enabled-at-boot-time;
> +		rs485-rts-active-low;
> +	};
> +};
> +
> +/* Configure PWM pins in GPIO mode: */
> +&gpio5 {
> +	gpio-line-names = "", "", "", "PWM3", "PWM2", "PWM1";
> +};
> +
> +&gpu {
> +	status = "disabled";
> +};
> +
> +&i2c2 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c2>;
> +	status = "okay";
> +
> +	eeprom_cb: eeprom@56 { /* Carrier board EEPROM */
> +		compatible = "atmel,24c04";
> +		reg = <0x56>;
> +		pagesize = <16>;
> +		vcc-supply = <&reg_3p3v>;
> +	};
> +
> +	lm75: sensor@48 {
> +		compatible = "st,stlm75";
> +		reg = <0x48>;
> +		vs-supply = <&reg_3p3v>;
> +	};
> +
> +	mcp7940: rtc@6f {
> +		compatible = "microchip,mcp7940x";
> +		reg = <0x6f>;
> +	};
> +};
> +
> +&i2c3 {
> +	codec@1a {
> +		status = "disabled";
> +	};
> +};
> +
> +&i2c4 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c4>;
> +	status = "okay";
> +
> +	pcf8574_1: gpio@38 {
> +		status = "okay";

Drop

> +		compatible = "nxp,pcf8574";
> +		reg = <0x38>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		gpio-line-names = "LED_B_COMM3", "LED_R_COMM3", "LED_G_COMM3",
> +		"TP14", "TP15", "LED_G_COMM4", "LED_R_COMM4", "LED_B_COMM4";
> +	};
> +
> +	pcf8574_2: gpio@39 {
> +		status = "okay";

Drop


> +		compatible = "nxp,pcf8574";
> +		reg = <0x39>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		gpio-line-names = "LED_B_COMM2", "LED_G_COMM2", "LED_B_COMM1",
> +		"LED_R_COMM2", "LED_R_COMM1", "LED_G_COMM1", "TP16", "TP17";
> +	};
> +};
> +
> +&uart2 {
> +	/delete-node/ bluetooth;

Why? If the hardware does not exist, why it is even in the DTSI? It does
exist, so removing is not correct.


> +};
> +
> +&usbotg1 {
> +	dr_mode = "host";
> +	disable-over-current;
> +	status = "okay";
> +};
> +
> +/* SD interface on expansion connector. */
> +&usdhc2 {
> +	/delete-property/vmmc-supply;

Why? The supply is needed.


Best regards,
Krzysztof
Hugo Villeneuve Nov. 2, 2023, 3:10 p.m. UTC | #2
On Thu, 2 Nov 2023 08:36:32 +0100
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote:

> On 01/11/2023 19:35, Hugo Villeneuve wrote:
> > From: Hugo Villeneuve <hvilleneuve@dimonoff.com>
> > 
> > The RVE gateway board is based on a Variscite VAR-SOM-NANO,
> > with a NXP MX8MN nano CPU.
> > 
> > Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
> > ---
> >  MAINTAINERS                                   |   7 +
> >  arch/arm64/boot/dts/freescale/Makefile        |   1 +
> >  .../boot/dts/freescale/imx8mn-rve-gateway.dts | 284 ++++++++++++++++++
> >  3 files changed, 292 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
> > 
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 43c5ed3c4508..9423b1bf35fc 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -18778,6 +18778,13 @@ F:	samples/rust/
> >  F:	scripts/*rust*
> >  K:	\b(?i:rust)\b
> >  
> > +RVE BOARD SUPPORT
> > +M:	Hugo Villeneuve <hvilleneuve@dimonoff.com>
> > +L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
> > +S:	Supported
> > +W:	https://rve.ca
> > +F:	arch/arm64/boot/dts/freescale/imx*rve-*.dts*
> 
> I still don't think individual boards should receive maintainer entry.
> https://lore.kernel.org/all/20210809080204.8381-1-shawnguo@kernel.org/

Hi,
ok, I was not aware of that. Will drop it for V3.


> > +
> >  RXRPC SOCKETS (AF_RXRPC)
> >  M:	David Howells <dhowells@redhat.com>
> >  M:	Marc Dionne <marc.dionne@auristor.com>
> > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> > index 89aee6c92576..760a0ca7adc3 100644
> > --- a/arch/arm64/boot/dts/freescale/Makefile
> > +++ b/arch/arm64/boot/dts/freescale/Makefile
> > @@ -89,6 +89,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2pro.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr3l-evk.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
> > +dtb-$(CONFIG_ARCH_MXC) += imx8mn-rve-gateway.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
> >  dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts b/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
> > new file mode 100644
> > index 000000000000..312718982a52
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
> > @@ -0,0 +1,284 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright 2023 DimOnOff
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include <dt-bindings/usb/pd.h>
> > +#include "imx8mn-var-som.dtsi"
> > +
> > +/ {
> > +	model = "RVE gateway";
> > +	compatible = "rve,rve-gateway", "fsl,imx8mn";
> 
> Missing compatible of SoM.

Fixed in V3.


> 
> > +
> > +	crystal_duart_24m: crystal-duart-24m {
> > +		compatible = "fixed-clock";
> > +		#clock-cells = <0>;
> > +		clock-frequency = <24000000>;
> > +	};
> > +
> > +	gpio-keys {
> > +		compatible = "gpio-keys";
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&pinctrl_gpio_keys>;
> > +		status = "okay";
> 
> Drop

Fixed in V3.

> 
> > +
> > +		key-enter {
> > +			label = "enter";
> > +			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> > +			linux,code = <KEY_ENTER>;
> > +		};
> > +
> > +		key-exit {
> > +			label = "exit";
> > +			gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
> > +			linux,code = <KEY_ESC>;
> > +		};
> > +	};
> > +
> > +	lcd {
> > +		compatible = "hit,hd44780";
> > +		display-height-chars = <2>;
> > +		display-width-chars = <20>;
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&pinctrl_lcd>;
> > +		data-gpios =
> > +			<&gpio5  1 GPIO_ACTIVE_HIGH>,
> 
> This should be after =, with the reset of lines properly aligned.

Fixed in V3.

> 
> > +			<&gpio1  6 GPIO_ACTIVE_HIGH>,
> > +			<&gpio1 14 GPIO_ACTIVE_HIGH>,
> > +			<&gpio4 28 GPIO_ACTIVE_HIGH>,
> > +			<&gpio5 24 GPIO_ACTIVE_HIGH>,
> > +			<&gpio5  2 GPIO_ACTIVE_HIGH>,
> > +			<&gpio1 12 GPIO_ACTIVE_HIGH>,
> > +			<&gpio5 25 GPIO_ACTIVE_HIGH>;
> > +		enable-gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>;
> > +		rs-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> > +		rw-gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
> > +	};
> > +
> > +	reg_3p3v: regulator-3p3v {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "3P3V";
> > +		regulator-min-microvolt = <3300000>;
> > +		regulator-max-microvolt = <3300000>;
> > +		regulator-always-on;
> > +		};
> 
> Fix indentation.

Fixed in V3.

> 
> > +
> > +	rotary: rotary-encoder { /* Bourns PEC12R rotary encoder, 24 steps. */
> 
> No comments after {. Put them in line before or after. This applies to
> other places as well.

Fixed all in V3.

> 
> > +		compatible = "rotary-encoder";
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&pinctrl_rotary>;
> > +		gpios =
> > +			<&gpio1  5 GPIO_ACTIVE_LOW>, /* A */
> 
> This should be after =, with the reset of lines properly aligned.

Fixed in V3.

> 
> 
> > +			<&gpio3 21 GPIO_ACTIVE_LOW>; /* B */
> > +		linux,axis = <0>; /* REL_X */
> > +		rotary-encoder,encoding = "gray";
> > +		rotary-encoder,relative-axis;
> > +	};
> > +};
> > +
> > +&ecspi1 {
> > +	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
> > +
> > +	duart1: serial@0 {
> > +		compatible = "nxp,sc16is752";
> > +		reg = <0>;
> > +		spi-rx-bus-width = <1>;
> > +		spi-tx-bus-width = <1>;
> > +		spi-max-frequency = <4000000>;
> > +		clocks = <&crystal_duart_24m>;
> > +		interrupt-parent = <&gpio3>;
> > +		interrupts = <22 IRQ_TYPE_EDGE_FALLING>;
> > +		gpio-controller;
> > +		#gpio-cells = <2>;
> > +		gpio-line-names = "RADIO0", "RADIO1", "RADIO2", "RADIO3",
> > +		"RADIO4", "RADIO_RESET", "TP12", "TP11";
> > +		linux,rs485-enabled-at-boot-time;
> > +		rs485-rts-active-low;
> > +	};
> > +
> > +	/delete-node/ touchscreen@0;
> > +};
> > +
> > +&ecspi2 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_ecspi2>;
> > +	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> > +	/delete-property/ dmas;
> > +	/delete-property/ dma-names;
> > +	status = "okay";
> > +
> > +	duart2: serial@0 {
> > +		compatible = "nxp,sc16is752";
> > +		reg = <0>;
> > +		spi-rx-bus-width = <1>;
> > +		spi-tx-bus-width = <1>;
> > +		spi-max-frequency = <4000000>;
> > +		clocks = <&crystal_duart_24m>;
> > +		interrupt-parent = <&gpio3>;
> > +		interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
> > +		gpio-controller;
> > +		#gpio-cells = <2>;
> > +		gpio-line-names = "LED_B_USER", "LED_R_USER", "LED_G_USER",
> > +		"GPIO_EXT3", "GPIO_EXT2", "GPIO_EXT1", "GPIO_EXT0", "TP13";
> > +		linux,rs485-enabled-at-boot-time;
> > +		rs485-rts-active-low;
> > +	};
> > +};
> > +
> > +/* Configure PWM pins in GPIO mode: */
> > +&gpio5 {
> > +	gpio-line-names = "", "", "", "PWM3", "PWM2", "PWM1";
> > +};
> > +
> > +&gpu {
> > +	status = "disabled";
> > +};
> > +
> > +&i2c2 {
> > +	clock-frequency = <400000>;
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_i2c2>;
> > +	status = "okay";
> > +
> > +	eeprom_cb: eeprom@56 { /* Carrier board EEPROM */
> > +		compatible = "atmel,24c04";
> > +		reg = <0x56>;
> > +		pagesize = <16>;
> > +		vcc-supply = <&reg_3p3v>;
> > +	};
> > +
> > +	lm75: sensor@48 {
> > +		compatible = "st,stlm75";
> > +		reg = <0x48>;
> > +		vs-supply = <&reg_3p3v>;
> > +	};
> > +
> > +	mcp7940: rtc@6f {
> > +		compatible = "microchip,mcp7940x";
> > +		reg = <0x6f>;
> > +	};
> > +};
> > +
> > +&i2c3 {
> > +	codec@1a {
> > +		status = "disabled";
> > +	};
> > +};
> > +
> > +&i2c4 {
> > +	clock-frequency = <400000>;
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_i2c4>;
> > +	status = "okay";
> > +
> > +	pcf8574_1: gpio@38 {
> > +		status = "okay";
> 
> Drop

Fixed all in V3.

> 
> > +		compatible = "nxp,pcf8574";
> > +		reg = <0x38>;
> > +		gpio-controller;
> > +		#gpio-cells = <2>;
> > +		gpio-line-names = "LED_B_COMM3", "LED_R_COMM3", "LED_G_COMM3",
> > +		"TP14", "TP15", "LED_G_COMM4", "LED_R_COMM4", "LED_B_COMM4";
> > +	};
> > +
> > +	pcf8574_2: gpio@39 {
> > +		status = "okay";
> 
> Drop
> 
> 
> > +		compatible = "nxp,pcf8574";
> > +		reg = <0x39>;
> > +		gpio-controller;
> > +		#gpio-cells = <2>;
> > +		gpio-line-names = "LED_B_COMM2", "LED_G_COMM2", "LED_B_COMM1",
> > +		"LED_R_COMM2", "LED_R_COMM1", "LED_G_COMM1", "TP16", "TP17";
> > +	};
> > +};
> > +
> > +&uart2 {
> > +	/delete-node/ bluetooth;
> 
> Why? If the hardware does not exist, why it is even in the DTSI? It does
> exist, so removing is not correct.

The current SOM DTSI is a melting pot of all "potentially" available
hardware, but there are a lot of SOM versions, with different
combinations of hardware components that can be populated or not...

The hardware do exist on some of our SOM versions, but not on some
others, and we do not use it at the moment.

In V3 I changed the line to:
    status = "disabled";

> 
> 
> > +};
> > +
> > +&usbotg1 {
> > +	dr_mode = "host";
> > +	disable-over-current;
> > +	status = "okay";
> > +};
> > +
> > +/* SD interface on expansion connector. */
> > +&usdhc2 {
> > +	/delete-property/vmmc-supply;
> 
> Why? The supply is needed.

The SOM dtsi references a regulator named reg_usdhc2_vmmc, but it
is not present in the SOM dtsi itself. Since we do not have such a
dedicated usdhc2 regulator on our board, initially I did this to get
rid of this error:
    Reference to non-existent node or label "reg_usdhc2_vmmc"

But for V3, I will change the vmmc-supply to refer to our board fixed
3.3V regulator:

 &usdhc2 {
+       vmmc-supply = <&reg_3p3v>;

Thank you for the review.

Hugo.


> 
> 
> Best regards,
> Krzysztof
> 
>
diff mbox series

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 43c5ed3c4508..9423b1bf35fc 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18778,6 +18778,13 @@  F:	samples/rust/
 F:	scripts/*rust*
 K:	\b(?i:rust)\b
 
+RVE BOARD SUPPORT
+M:	Hugo Villeneuve <hvilleneuve@dimonoff.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Supported
+W:	https://rve.ca
+F:	arch/arm64/boot/dts/freescale/imx*rve-*.dts*
+
 RXRPC SOCKETS (AF_RXRPC)
 M:	David Howells <dhowells@redhat.com>
 M:	Marc Dionne <marc.dionne@auristor.com>
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 89aee6c92576..760a0ca7adc3 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -89,6 +89,7 @@  dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2pro.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr3l-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mn-rve-gateway.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts b/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
new file mode 100644
index 000000000000..312718982a52
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-rve-gateway.dts
@@ -0,0 +1,284 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2023 DimOnOff
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/usb/pd.h>
+#include "imx8mn-var-som.dtsi"
+
+/ {
+	model = "RVE gateway";
+	compatible = "rve,rve-gateway", "fsl,imx8mn";
+
+	crystal_duart_24m: crystal-duart-24m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		status = "okay";
+
+		key-enter {
+			label = "enter";
+			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ENTER>;
+		};
+
+		key-exit {
+			label = "exit";
+			gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ESC>;
+		};
+	};
+
+	lcd {
+		compatible = "hit,hd44780";
+		display-height-chars = <2>;
+		display-width-chars = <20>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcd>;
+		data-gpios =
+			<&gpio5  1 GPIO_ACTIVE_HIGH>,
+			<&gpio1  6 GPIO_ACTIVE_HIGH>,
+			<&gpio1 14 GPIO_ACTIVE_HIGH>,
+			<&gpio4 28 GPIO_ACTIVE_HIGH>,
+			<&gpio5 24 GPIO_ACTIVE_HIGH>,
+			<&gpio5  2 GPIO_ACTIVE_HIGH>,
+			<&gpio1 12 GPIO_ACTIVE_HIGH>,
+			<&gpio5 25 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>;
+		rs-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		rw-gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		};
+
+	rotary: rotary-encoder { /* Bourns PEC12R rotary encoder, 24 steps. */
+		compatible = "rotary-encoder";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rotary>;
+		gpios =
+			<&gpio1  5 GPIO_ACTIVE_LOW>, /* A */
+			<&gpio3 21 GPIO_ACTIVE_LOW>; /* B */
+		linux,axis = <0>; /* REL_X */
+		rotary-encoder,encoding = "gray";
+		rotary-encoder,relative-axis;
+	};
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+
+	duart1: serial@0 {
+		compatible = "nxp,sc16is752";
+		reg = <0>;
+		spi-rx-bus-width = <1>;
+		spi-tx-bus-width = <1>;
+		spi-max-frequency = <4000000>;
+		clocks = <&crystal_duart_24m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <22 IRQ_TYPE_EDGE_FALLING>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "RADIO0", "RADIO1", "RADIO2", "RADIO3",
+		"RADIO4", "RADIO_RESET", "TP12", "TP11";
+		linux,rs485-enabled-at-boot-time;
+		rs485-rts-active-low;
+	};
+
+	/delete-node/ touchscreen@0;
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	/delete-property/ dmas;
+	/delete-property/ dma-names;
+	status = "okay";
+
+	duart2: serial@0 {
+		compatible = "nxp,sc16is752";
+		reg = <0>;
+		spi-rx-bus-width = <1>;
+		spi-tx-bus-width = <1>;
+		spi-max-frequency = <4000000>;
+		clocks = <&crystal_duart_24m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "LED_B_USER", "LED_R_USER", "LED_G_USER",
+		"GPIO_EXT3", "GPIO_EXT2", "GPIO_EXT1", "GPIO_EXT0", "TP13";
+		linux,rs485-enabled-at-boot-time;
+		rs485-rts-active-low;
+	};
+};
+
+/* Configure PWM pins in GPIO mode: */
+&gpio5 {
+	gpio-line-names = "", "", "", "PWM3", "PWM2", "PWM1";
+};
+
+&gpu {
+	status = "disabled";
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	eeprom_cb: eeprom@56 { /* Carrier board EEPROM */
+		compatible = "atmel,24c04";
+		reg = <0x56>;
+		pagesize = <16>;
+		vcc-supply = <&reg_3p3v>;
+	};
+
+	lm75: sensor@48 {
+		compatible = "st,stlm75";
+		reg = <0x48>;
+		vs-supply = <&reg_3p3v>;
+	};
+
+	mcp7940: rtc@6f {
+		compatible = "microchip,mcp7940x";
+		reg = <0x6f>;
+	};
+};
+
+&i2c3 {
+	codec@1a {
+		status = "disabled";
+	};
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	pcf8574_1: gpio@38 {
+		status = "okay";
+		compatible = "nxp,pcf8574";
+		reg = <0x38>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "LED_B_COMM3", "LED_R_COMM3", "LED_G_COMM3",
+		"TP14", "TP15", "LED_G_COMM4", "LED_R_COMM4", "LED_B_COMM4";
+	};
+
+	pcf8574_2: gpio@39 {
+		status = "okay";
+		compatible = "nxp,pcf8574";
+		reg = <0x39>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "LED_B_COMM2", "LED_G_COMM2", "LED_B_COMM1",
+		"LED_R_COMM2", "LED_R_COMM1", "LED_G_COMM1", "TP16", "TP17";
+	};
+};
+
+&uart2 {
+	/delete-node/ bluetooth;
+};
+
+&usbotg1 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+/* SD interface on expansion connector. */
+&usdhc2 {
+	/delete-property/vmmc-supply;
+	cd-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK	0x13
+			MX8MN_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI	0x13
+			MX8MN_IOMUXC_ECSPI1_MISO_ECSPI1_MISO	0x13
+			MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9	0x13 /* SS0 */
+			MX8MN_IOMUXC_SAI5_RXD1_GPIO3_IO22	0x13 /* SC16 IRQ */
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0x13
+			MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0x13
+			MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0x13
+			MX8MN_IOMUXC_ECSPI2_SS0_GPIO5_IO13	0x13 /* SS0 */
+			MX8MN_IOMUXC_SAI5_RXC_GPIO3_IO20	0x13 /* SC16 IRQ */
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO01_GPIO1_IO1	0xc6 /* Enter */
+			MX8MN_IOMUXC_SAI5_RXD2_GPIO3_IO23	0xc6 /* Exit */
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL		0x400001c3
+			MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_I2C4_SCL_I2C4_SCL		0x400001c3
+			MX8MN_IOMUXC_I2C4_SDA_I2C4_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_lcd: lcdgrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_SAI3_TXD_GPIO5_IO1		0x00000156 /* D0 */
+			MX8MN_IOMUXC_GPIO1_IO06_GPIO1_IO6	0x00000156 /* D1 */
+			MX8MN_IOMUXC_GPIO1_IO14_GPIO1_IO14	0x00000156 /* D2 */
+			MX8MN_IOMUXC_SAI3_RXFS_GPIO4_IO28	0x00000156 /* D3 */
+			MX8MN_IOMUXC_UART2_RXD_GPIO5_IO24	0x00000156 /* D4 */
+			MX8MN_IOMUXC_SAI3_MCLK_GPIO5_IO2	0x00000156 /* D5 */
+			MX8MN_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x00000156 /* D6 */
+			MX8MN_IOMUXC_UART2_TXD_GPIO5_IO25	0x00000156 /* D7 */
+			MX8MN_IOMUXC_UART1_TXD_GPIO5_IO23	0x00000156 /* E */
+			MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7	0x00000156 /* RS */
+			MX8MN_IOMUXC_SAI2_MCLK_GPIO4_IO27	0x00000156 /* R/W */
+		>;
+	};
+
+	pinctrl_rotary: rotarygrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO05_GPIO1_IO5	0x00000156 /* A */
+			MX8MN_IOMUXC_SAI5_RXD0_GPIO3_IO21	0x00000156 /* B */
+		>;
+	};
+
+	/* Override Card Detect function GPIO value (GPIO1_IO10) from SOM: */
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x41
+		>;
+	};
+};