diff mbox series

[07/21] serial: msm: add debug UART

Message ID 20231121-b4-qcom-common-target-v1-7-9492198e0c15@linaro.org
State Superseded
Headers show
Series Qualcomm generic board support | expand

Commit Message

Caleb Connolly Nov. 21, 2023, 5:09 p.m. UTC
Introduce support for early debugging.

Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
---
 drivers/serial/Kconfig      |  8 ++++++++
 drivers/serial/serial_msm.c | 37 +++++++++++++++++++++++++++++++++++++
 2 files changed, 45 insertions(+)
diff mbox series

Patch

diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 81fdac047824..20713812c839 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -304,6 +304,14 @@  config DEBUG_UART_S5P
 	  will need to provide parameters to make this work. The driver will
 	  be available until the real driver-model serial is running.
 
+config DEBUG_UART_MSM
+	bool "Qualcomm QUP UART debug"
+	depends on ARCH_SNAPDRAGON
+	help
+	  Select this to enable a debug UART using the serial_msm driver. You
+	  will need to provide parameters to make this work. The driver will
+	  be available until the real driver-model serial is running.
+
 config DEBUG_UART_MSM_GENI
 	bool "Qualcomm snapdragon"
 	depends on ARCH_SNAPDRAGON
diff --git a/drivers/serial/serial_msm.c b/drivers/serial/serial_msm.c
index a22623c316ed..6a4d6f1d96fd 100644
--- a/drivers/serial/serial_msm.c
+++ b/drivers/serial/serial_msm.c
@@ -253,3 +253,40 @@  U_BOOT_DRIVER(serial_msm) = {
 	.probe = msm_serial_probe,
 	.ops	= &msm_serial_ops,
 };
+
+#ifdef CONFIG_DEBUG_UART_MSM
+
+static struct msm_serial_data init_serial_data = {
+	.base = CONFIG_VAL(DEBUG_UART_BASE),
+	.clk_bit_rate = UART_DM_CLK_RX_TX_BIT_RATE,
+};
+
+/* Serial dumb device, to reuse driver code */
+static struct udevice init_dev = {
+	.priv_ = &init_serial_data,
+};
+
+#include <debug_uart.h>
+
+static inline void _debug_uart_init(void)
+{
+	uart_dm_init(&init_serial_data);
+}
+
+static inline void _debug_uart_putc(int ch)
+{
+	struct msm_serial_data *priv = &init_serial_data;
+
+	while (!(readl(priv->base + UARTDM_SR) & UARTDM_SR_TX_EMPTY) &&
+	       !(readl(priv->base + UARTDM_ISR) & UARTDM_ISR_TX_READY))
+		;
+
+	writel(UARTDM_CR_CMD_RESET_TX_READY, priv->base + UARTDM_CR);
+
+	writel(1, priv->base + UARTDM_NCF_TX);
+	writel(ch, priv->base + UARTDM_TF);
+}
+
+DEBUG_UART_FUNCS
+
+#endif