diff mbox series

[RFC,2/2] PCI: acpiphp: slowdown hotplug if hotplugging multiple devices at a time

Message ID 20231213003614.1648343-3-imammedo@redhat.com
State New
Headers show
Series PCI: acpiphp: workaround race between hotplug and SCSI_SCAN_ASYNC job | expand

Commit Message

Igor Mammedov Dec. 13, 2023, 12:36 a.m. UTC
previous commit ("PCI: acpiphp: enable slot only if it hasn't been enabled already"
introduced a workaround to avoid a race between SCSI_SCAN_ASYNC job and
bridge reconfiguration in case of single HBA hotplug.
However in virt environment it's possible to pause machine hotplug several
HBAs and let machine run. That can hit the same race when 2nd hotplugged
HBA will start re-configuring bridge.
Do the same thing as SHPC and throttle down hotplug of 2nd and up
devices within single hotplug event.

Signed-off-by: Igor Mammedov <imammedo@redhat.com>
---
 drivers/pci/hotplug/acpiphp_glue.c | 6 ++++++
 1 file changed, 6 insertions(+)

Comments

Greg Kroah-Hartman Dec. 13, 2023, 7:26 a.m. UTC | #1
On Wed, Dec 13, 2023 at 01:36:14AM +0100, Igor Mammedov wrote:
> previous commit ("PCI: acpiphp: enable slot only if it hasn't been enabled already"
> introduced a workaround to avoid a race between SCSI_SCAN_ASYNC job and
> bridge reconfiguration in case of single HBA hotplug.
> However in virt environment it's possible to pause machine hotplug several
> HBAs and let machine run. That can hit the same race when 2nd hotplugged
> HBA will start re-configuring bridge.
> Do the same thing as SHPC and throttle down hotplug of 2nd and up
> devices within single hotplug event.
> 
> Signed-off-by: Igor Mammedov <imammedo@redhat.com>
> ---
>  drivers/pci/hotplug/acpiphp_glue.c | 6 ++++++
>  1 file changed, 6 insertions(+)
> 
> diff --git a/drivers/pci/hotplug/acpiphp_glue.c b/drivers/pci/hotplug/acpiphp_glue.c
> index 6b11609927d6..30bca2086b24 100644
> --- a/drivers/pci/hotplug/acpiphp_glue.c
> +++ b/drivers/pci/hotplug/acpiphp_glue.c
> @@ -37,6 +37,7 @@
>  #include <linux/mutex.h>
>  #include <linux/slab.h>
>  #include <linux/acpi.h>
> +#include <linux/delay.h>
>  
>  #include "../pci.h"
>  #include "acpiphp.h"
> @@ -700,6 +701,7 @@ static void trim_stale_devices(struct pci_dev *dev)
>  static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
>  {
>  	struct acpiphp_slot *slot;
> +        int nr_hp_slots = 0;
>  
>  	/* Bail out if the bridge is going away. */
>  	if (bridge->is_going_away)
> @@ -723,6 +725,10 @@ static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
>  
>  			/* configure all functions */
>  			if (slot->flags != SLOT_ENABLED) {
> +				if (nr_hp_slots)
> +					msleep(1000);
> +
> +                                ++nr_hp_slots;
>  				enable_slot(slot, true);
>  			}
>  		} else {
> -- 
> 2.39.3
> 
> 

<formletter>

This is not the correct way to submit patches for inclusion in the
stable kernel tree.  Please read:
    https://www.kernel.org/doc/html/latest/process/stable-kernel-rules.html
for how to do this properly.

</formletter>
Dongli Zhang Dec. 13, 2023, 8:13 a.m. UTC | #2
Hi Igor,


On 12/12/23 16:36, Igor Mammedov wrote:
> previous commit ("PCI: acpiphp: enable slot only if it hasn't been enabled already"
> introduced a workaround to avoid a race between SCSI_SCAN_ASYNC job and
> bridge reconfiguration in case of single HBA hotplug.
> However in virt environment it's possible to pause machine hotplug several
> HBAs and let machine run. That can hit the same race when 2nd hotplugged

Would you mind helping explain what does "pause machine hotplug several HBAs and
let machine run" indicate?

Thank you very much!

Dongli Zhang

> HBA will start re-configuring bridge.
> Do the same thing as SHPC and throttle down hotplug of 2nd and up
> devices within single hotplug event.
> 
> Signed-off-by: Igor Mammedov <imammedo@redhat.com>
> ---
>  drivers/pci/hotplug/acpiphp_glue.c | 6 ++++++
>  1 file changed, 6 insertions(+)
> 
> diff --git a/drivers/pci/hotplug/acpiphp_glue.c b/drivers/pci/hotplug/acpiphp_glue.c
> index 6b11609927d6..30bca2086b24 100644
> --- a/drivers/pci/hotplug/acpiphp_glue.c
> +++ b/drivers/pci/hotplug/acpiphp_glue.c
> @@ -37,6 +37,7 @@
>  #include <linux/mutex.h>
>  #include <linux/slab.h>
>  #include <linux/acpi.h>
> +#include <linux/delay.h>
>  
>  #include "../pci.h"
>  #include "acpiphp.h"
> @@ -700,6 +701,7 @@ static void trim_stale_devices(struct pci_dev *dev)
>  static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
>  {
>  	struct acpiphp_slot *slot;
> +        int nr_hp_slots = 0;
>  
>  	/* Bail out if the bridge is going away. */
>  	if (bridge->is_going_away)
> @@ -723,6 +725,10 @@ static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
>  
>  			/* configure all functions */
>  			if (slot->flags != SLOT_ENABLED) {
> +				if (nr_hp_slots)
> +					msleep(1000);
> +
> +                                ++nr_hp_slots;
>  				enable_slot(slot, true);
>  			}
>  		} else {
Michael S. Tsirkin Dec. 13, 2023, 4:54 p.m. UTC | #3
On Wed, Dec 13, 2023 at 05:49:39PM +0100, Igor Mammedov wrote:
> On Wed, Dec 13, 2023 at 2:08 PM Rafael J. Wysocki <rafael@kernel.org> wrote:
> >
> > On Wed, Dec 13, 2023 at 1:36 AM Igor Mammedov <imammedo@redhat.com> wrote:
> > >
> > > previous commit ("PCI: acpiphp: enable slot only if it hasn't been enabled already"
> > > introduced a workaround to avoid a race between SCSI_SCAN_ASYNC job and
> > > bridge reconfiguration in case of single HBA hotplug.
> > > However in virt environment it's possible to pause machine hotplug several
> > > HBAs and let machine run. That can hit the same race when 2nd hotplugged
> > > HBA will start re-configuring bridge.
> > > Do the same thing as SHPC and throttle down hotplug of 2nd and up
> > > devices within single hotplug event.
> > >
> > > Signed-off-by: Igor Mammedov <imammedo@redhat.com>
> > > ---
> > >  drivers/pci/hotplug/acpiphp_glue.c | 6 ++++++
> > >  1 file changed, 6 insertions(+)
> > >
> > > diff --git a/drivers/pci/hotplug/acpiphp_glue.c b/drivers/pci/hotplug/acpiphp_glue.c
> > > index 6b11609927d6..30bca2086b24 100644
> > > --- a/drivers/pci/hotplug/acpiphp_glue.c
> > > +++ b/drivers/pci/hotplug/acpiphp_glue.c
> > > @@ -37,6 +37,7 @@
> > >  #include <linux/mutex.h>
> > >  #include <linux/slab.h>
> > >  #include <linux/acpi.h>
> > > +#include <linux/delay.h>
> > >
> > >  #include "../pci.h"
> > >  #include "acpiphp.h"
> > > @@ -700,6 +701,7 @@ static void trim_stale_devices(struct pci_dev *dev)
> > >  static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
> > >  {
> > >         struct acpiphp_slot *slot;
> > > +        int nr_hp_slots = 0;
> > >
> > >         /* Bail out if the bridge is going away. */
> > >         if (bridge->is_going_away)
> > > @@ -723,6 +725,10 @@ static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
> > >
> > >                         /* configure all functions */
> > >                         if (slot->flags != SLOT_ENABLED) {
> > > +                               if (nr_hp_slots)
> > > +                                       msleep(1000);
> >
> > Why is 1000 considered the most suitable number here?  Any chance to
> > define a symbol for it?
> 
> Timeout was borrowed from SHPC hotplug workflow where it apparently
> makes race harder to reproduce.
> (though it's not excuse to add more timeouts elsewhere)
> 
> > And won't this affect the cases when the race in question is not a concern?
> 
> In practice it's not likely, since even in virt scenario hypervisor won't
> stop VM to hotplug device (which beats whole purpose of hotplug).
> 
> But in case of a very slow VM (overcommit case) it's possible for
> several HBA's to be hotplugged by the time acpiphp gets a chance
> to handle the 1st hotplug event. SHPC is more or less 'safe' with its
> 1sec delay.
> 
> > Also, adding arbitrary timeouts is not the most robust way of
> > addressing race conditions IMV.  Wouldn't it be better to add some
> > proper synchronization between the pieces of code that can race with
> > each other?
> 
> I don't like it either, it's a stop gap measure to hide regression on
> short notice,
> which I can fixup without much risk in short time left, before folks
> leave on holidays.
> It's fine to drop the patch as chances of this happening are small.
> [1/2] should cover reported cases.
> 
> Since it's RFC, I basically ask for opinions on a proper way to fix
> SCSI_ASYNC_SCAN
> running wild while the hotplug is in progress (and maybe SCSI is not
> the only user that
> schedules async job from device probe).

Of course not. And things don't have to be scheduled from probe right?
Can be triggered by an interrupt or userspace activity.

> So adding synchronisation and testing
> would take time (not something I'd do this late in the cycle).
> 
> So far I'm thinking about adding rw mutex to bridge with the PCI
> hotplug subsystem
> being a writer while scsi scan jobs would be readers and wait till hotplug code
> says it's safe to proceed.
> I plan to work in this direction and give it some testing, unless
> someone has a better idea.

> >
> > > +
> > > +                                ++nr_hp_slots;
> > >                                 enable_slot(slot, true);
> > >                         }
> > >                 } else {
> > > --
> >
Dongli Zhang Dec. 13, 2023, 5:25 p.m. UTC | #4
Hi Igor,

On 12/13/23 02:05, Igor Mammedov wrote:
> On Wed, 13 Dec 2023 00:13:37 -0800
> Dongli Zhang <dongli.zhang@oracle.com> wrote:
> 
>> Hi Igor,
>>
>>
>> On 12/12/23 16:36, Igor Mammedov wrote:
>>> previous commit ("PCI: acpiphp: enable slot only if it hasn't been enabled already"
>>> introduced a workaround to avoid a race between SCSI_SCAN_ASYNC job and
>>> bridge reconfiguration in case of single HBA hotplug.
>>> However in virt environment it's possible to pause machine hotplug several
>>> HBAs and let machine run. That can hit the same race when 2nd hotplugged  
>>
>> Would you mind helping explain what does "pause machine hotplug several HBAs and
>> let machine run" indicate?
> 
> qemu example would be:
> {qemu) stop
> (qemu) device_add device_add vhost-scsi-pci,wwpn=naa.5001405324af0985,id=vhost01,bus=bridge1,addr=8
> (qemu) device_add vhost-scsi-pci,wwpn=naa.5001405324af0986,id=vhost02,bus=bridge1,addr=0
> (qemu) cont
> 
> this way when machine continues to run acpiphp code will see 2 HBAs at once
> and try to process one right after another. So [1/2] patch is not enough
> to cover above case, and hence the same hack SHPC employs by adding delay.
> However 2 separate hotplug events as in your reproducer should be covered
> by the 1st patch.

Thank you very much for the explanation.

That indicates the two PCI devices will be detected and enabled in the same
event. Neither of the two PCI devices used to be enabled.

As mentioned in another email, I do not think this is the way to even workaround
the issue, because there are other ways to do mmio at the same time point.

Dongli Zhang

> 
>> Thank you very much!
>>
>> Dongli Zhang
>>
>>> HBA will start re-configuring bridge.
>>> Do the same thing as SHPC and throttle down hotplug of 2nd and up
>>> devices within single hotplug event.
>>>
>>> Signed-off-by: Igor Mammedov <imammedo@redhat.com>
>>> ---
>>>  drivers/pci/hotplug/acpiphp_glue.c | 6 ++++++
>>>  1 file changed, 6 insertions(+)
>>>
>>> diff --git a/drivers/pci/hotplug/acpiphp_glue.c b/drivers/pci/hotplug/acpiphp_glue.c
>>> index 6b11609927d6..30bca2086b24 100644
>>> --- a/drivers/pci/hotplug/acpiphp_glue.c
>>> +++ b/drivers/pci/hotplug/acpiphp_glue.c
>>> @@ -37,6 +37,7 @@
>>>  #include <linux/mutex.h>
>>>  #include <linux/slab.h>
>>>  #include <linux/acpi.h>
>>> +#include <linux/delay.h>
>>>  
>>>  #include "../pci.h"
>>>  #include "acpiphp.h"
>>> @@ -700,6 +701,7 @@ static void trim_stale_devices(struct pci_dev *dev)
>>>  static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
>>>  {
>>>  	struct acpiphp_slot *slot;
>>> +        int nr_hp_slots = 0;
>>>  
>>>  	/* Bail out if the bridge is going away. */
>>>  	if (bridge->is_going_away)
>>> @@ -723,6 +725,10 @@ static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
>>>  
>>>  			/* configure all functions */
>>>  			if (slot->flags != SLOT_ENABLED) {
>>> +				if (nr_hp_slots)
>>> +					msleep(1000);
>>> +
>>> +                                ++nr_hp_slots;
>>>  				enable_slot(slot, true);
>>>  			}
>>>  		} else {  
>>
>
Igor Mammedov Jan. 3, 2024, 9:54 a.m. UTC | #5
On Wed, 13 Dec 2023 09:09:18 -0800
Dongli Zhang <dongli.zhang@oracle.com> wrote:

> Hi Igor,
> 
> On 12/13/23 08:54, Michael S. Tsirkin wrote:
> > On Wed, Dec 13, 2023 at 05:49:39PM +0100, Igor Mammedov wrote:  
> >> On Wed, Dec 13, 2023 at 2:08 PM Rafael J. Wysocki <rafael@kernel.org> wrote:  
> >>>
> >>> On Wed, Dec 13, 2023 at 1:36 AM Igor Mammedov <imammedo@redhat.com> wrote:  
> >>>>
> >>>> previous commit ("PCI: acpiphp: enable slot only if it hasn't been enabled already"
> >>>> introduced a workaround to avoid a race between SCSI_SCAN_ASYNC job and
> >>>> bridge reconfiguration in case of single HBA hotplug.
> >>>> However in virt environment it's possible to pause machine hotplug several
> >>>> HBAs and let machine run. That can hit the same race when 2nd hotplugged
> >>>> HBA will start re-configuring bridge.
> >>>> Do the same thing as SHPC and throttle down hotplug of 2nd and up
> >>>> devices within single hotplug event.
> >>>>
> >>>> Signed-off-by: Igor Mammedov <imammedo@redhat.com>
> >>>> ---
> >>>>  drivers/pci/hotplug/acpiphp_glue.c | 6 ++++++
> >>>>  1 file changed, 6 insertions(+)
> >>>>
> >>>> diff --git a/drivers/pci/hotplug/acpiphp_glue.c b/drivers/pci/hotplug/acpiphp_glue.c
> >>>> index 6b11609927d6..30bca2086b24 100644
> >>>> --- a/drivers/pci/hotplug/acpiphp_glue.c
> >>>> +++ b/drivers/pci/hotplug/acpiphp_glue.c
> >>>> @@ -37,6 +37,7 @@
> >>>>  #include <linux/mutex.h>
> >>>>  #include <linux/slab.h>
> >>>>  #include <linux/acpi.h>
> >>>> +#include <linux/delay.h>
> >>>>
> >>>>  #include "../pci.h"
> >>>>  #include "acpiphp.h"
> >>>> @@ -700,6 +701,7 @@ static void trim_stale_devices(struct pci_dev *dev)
> >>>>  static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
> >>>>  {
> >>>>         struct acpiphp_slot *slot;
> >>>> +        int nr_hp_slots = 0;
> >>>>
> >>>>         /* Bail out if the bridge is going away. */
> >>>>         if (bridge->is_going_away)
> >>>> @@ -723,6 +725,10 @@ static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
> >>>>
> >>>>                         /* configure all functions */
> >>>>                         if (slot->flags != SLOT_ENABLED) {
> >>>> +                               if (nr_hp_slots)
> >>>> +                                       msleep(1000);  
> >>>
> >>> Why is 1000 considered the most suitable number here?  Any chance to
> >>> define a symbol for it?  
> >>
> >> Timeout was borrowed from SHPC hotplug workflow where it apparently
> >> makes race harder to reproduce.
> >> (though it's not excuse to add more timeouts elsewhere)
> >>  
> >>> And won't this affect the cases when the race in question is not a concern?  
> >>
> >> In practice it's not likely, since even in virt scenario hypervisor won't
> >> stop VM to hotplug device (which beats whole purpose of hotplug).
> >>
> >> But in case of a very slow VM (overcommit case) it's possible for
> >> several HBA's to be hotplugged by the time acpiphp gets a chance
> >> to handle the 1st hotplug event. SHPC is more or less 'safe' with its
> >> 1sec delay.
> >>  
> >>> Also, adding arbitrary timeouts is not the most robust way of
> >>> addressing race conditions IMV.  Wouldn't it be better to add some
> >>> proper synchronization between the pieces of code that can race with
> >>> each other?  
> >>
> >> I don't like it either, it's a stop gap measure to hide regression on
> >> short notice,
> >> which I can fixup without much risk in short time left, before folks
> >> leave on holidays.
> >> It's fine to drop the patch as chances of this happening are small.
> >> [1/2] should cover reported cases.
> >>
> >> Since it's RFC, I basically ask for opinions on a proper way to fix
> >> SCSI_ASYNC_SCAN
> >> running wild while the hotplug is in progress (and maybe SCSI is not
> >> the only user that
> >> schedules async job from device probe).  
> > 
> > Of course not. And things don't have to be scheduled from probe right?
> > Can be triggered by an interrupt or userspace activity.  
> 
> I agree with Michael. TBH, I am curious if the two patches can
> workaround/resolve the issue.
> 
> Would you mind helping explain if to run enable_slot() for a new PCI device can
> impact the other PCI devices existing on the bridge?
> 
> E.g.,:
> 
> 1. Attach several virtio-scsi or virtio-net on the same bridge.
> 
> 2. Trigger workload for those PCI devices. They may do mmio write to kick the
> doorbell (to trigger KVM/QEMU ioeventfd) very frequently.
> 
> 3. Now hot-add an extra PCI device. Since the slot is never enabled, it enables
> the slot via enable_slot().
> 
> Can I assume the last enable_slot() will temporarily re-configure the bridge
> window so that all other PCI devices' mmio will lose effect at that time point?

That's likely what would happen.
The same issue should apply to native PCIe and SHPC hotplug, as they also use
pci_assign_unassigned_bridge_resources().

Perhaps drivers have to be taught that PCI tree is being reconfigured or some
another approach can be used to deal with it.
Do you have any ideas?

I'm comparing with Windows guest, which manages to reconfigure PCI hierarchy
on the fly. (though I haven't tested that under heavy load with several
devices on a bridge).

> Since drivers always kick the doorbell conditionally, they may hang forever.
> 
> As I have reported, we used to have the similar issue.
> 
> PCI: Probe bridge window attributes once at enumeration-time
> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=51c48b310183ab6ba5419edfc6a8de889cc04521
> 
> 
> Therefore, can I assume the issue is not because to re-enable an already-enabled
> slot, but to touch the bridge window for more than once?
> 
> Thank you very much!
> 
> Dongli Zhang
> 
> >   
> >> So adding synchronisation and testing
> >> would take time (not something I'd do this late in the cycle).
> >>
> >> So far I'm thinking about adding rw mutex to bridge with the PCI
> >> hotplug subsystem
> >> being a writer while scsi scan jobs would be readers and wait till hotplug code
> >> says it's safe to proceed.
> >> I plan to work in this direction and give it some testing, unless
> >> someone has a better idea.  
> >   
> >>>  
> >>>> +
> >>>> +                                ++nr_hp_slots;
> >>>>                                 enable_slot(slot, true);
> >>>>                         }
> >>>>                 } else {
> >>>> --  
> >>>  
> >   
>
Dongli Zhang Jan. 3, 2024, 4:19 p.m. UTC | #6
Hi Igor,

On 1/3/24 01:54, Igor Mammedov wrote:
> On Wed, 13 Dec 2023 09:09:18 -0800
> Dongli Zhang <dongli.zhang@oracle.com> wrote:
> 
>> Hi Igor,
>>
>> On 12/13/23 08:54, Michael S. Tsirkin wrote:
>>> On Wed, Dec 13, 2023 at 05:49:39PM +0100, Igor Mammedov wrote:  
>>>> On Wed, Dec 13, 2023 at 2:08 PM Rafael J. Wysocki <rafael@kernel.org> wrote:  
>>>>>
>>>>> On Wed, Dec 13, 2023 at 1:36 AM Igor Mammedov <imammedo@redhat.com> wrote:  
>>>>>>
>>>>>> previous commit ("PCI: acpiphp: enable slot only if it hasn't been enabled already"
>>>>>> introduced a workaround to avoid a race between SCSI_SCAN_ASYNC job and
>>>>>> bridge reconfiguration in case of single HBA hotplug.
>>>>>> However in virt environment it's possible to pause machine hotplug several
>>>>>> HBAs and let machine run. That can hit the same race when 2nd hotplugged
>>>>>> HBA will start re-configuring bridge.
>>>>>> Do the same thing as SHPC and throttle down hotplug of 2nd and up
>>>>>> devices within single hotplug event.
>>>>>>
>>>>>> Signed-off-by: Igor Mammedov <imammedo@redhat.com>
>>>>>> ---
>>>>>>  drivers/pci/hotplug/acpiphp_glue.c | 6 ++++++
>>>>>>  1 file changed, 6 insertions(+)
>>>>>>
>>>>>> diff --git a/drivers/pci/hotplug/acpiphp_glue.c b/drivers/pci/hotplug/acpiphp_glue.c
>>>>>> index 6b11609927d6..30bca2086b24 100644
>>>>>> --- a/drivers/pci/hotplug/acpiphp_glue.c
>>>>>> +++ b/drivers/pci/hotplug/acpiphp_glue.c
>>>>>> @@ -37,6 +37,7 @@
>>>>>>  #include <linux/mutex.h>
>>>>>>  #include <linux/slab.h>
>>>>>>  #include <linux/acpi.h>
>>>>>> +#include <linux/delay.h>
>>>>>>
>>>>>>  #include "../pci.h"
>>>>>>  #include "acpiphp.h"
>>>>>> @@ -700,6 +701,7 @@ static void trim_stale_devices(struct pci_dev *dev)
>>>>>>  static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
>>>>>>  {
>>>>>>         struct acpiphp_slot *slot;
>>>>>> +        int nr_hp_slots = 0;
>>>>>>
>>>>>>         /* Bail out if the bridge is going away. */
>>>>>>         if (bridge->is_going_away)
>>>>>> @@ -723,6 +725,10 @@ static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
>>>>>>
>>>>>>                         /* configure all functions */
>>>>>>                         if (slot->flags != SLOT_ENABLED) {
>>>>>> +                               if (nr_hp_slots)
>>>>>> +                                       msleep(1000);  
>>>>>
>>>>> Why is 1000 considered the most suitable number here?  Any chance to
>>>>> define a symbol for it?  
>>>>
>>>> Timeout was borrowed from SHPC hotplug workflow where it apparently
>>>> makes race harder to reproduce.
>>>> (though it's not excuse to add more timeouts elsewhere)
>>>>  
>>>>> And won't this affect the cases when the race in question is not a concern?  
>>>>
>>>> In practice it's not likely, since even in virt scenario hypervisor won't
>>>> stop VM to hotplug device (which beats whole purpose of hotplug).
>>>>
>>>> But in case of a very slow VM (overcommit case) it's possible for
>>>> several HBA's to be hotplugged by the time acpiphp gets a chance
>>>> to handle the 1st hotplug event. SHPC is more or less 'safe' with its
>>>> 1sec delay.
>>>>  
>>>>> Also, adding arbitrary timeouts is not the most robust way of
>>>>> addressing race conditions IMV.  Wouldn't it be better to add some
>>>>> proper synchronization between the pieces of code that can race with
>>>>> each other?  
>>>>
>>>> I don't like it either, it's a stop gap measure to hide regression on
>>>> short notice,
>>>> which I can fixup without much risk in short time left, before folks
>>>> leave on holidays.
>>>> It's fine to drop the patch as chances of this happening are small.
>>>> [1/2] should cover reported cases.
>>>>
>>>> Since it's RFC, I basically ask for opinions on a proper way to fix
>>>> SCSI_ASYNC_SCAN
>>>> running wild while the hotplug is in progress (and maybe SCSI is not
>>>> the only user that
>>>> schedules async job from device probe).  
>>>
>>> Of course not. And things don't have to be scheduled from probe right?
>>> Can be triggered by an interrupt or userspace activity.  
>>
>> I agree with Michael. TBH, I am curious if the two patches can
>> workaround/resolve the issue.
>>
>> Would you mind helping explain if to run enable_slot() for a new PCI device can
>> impact the other PCI devices existing on the bridge?
>>
>> E.g.,:
>>
>> 1. Attach several virtio-scsi or virtio-net on the same bridge.
>>
>> 2. Trigger workload for those PCI devices. They may do mmio write to kick the
>> doorbell (to trigger KVM/QEMU ioeventfd) very frequently.
>>
>> 3. Now hot-add an extra PCI device. Since the slot is never enabled, it enables
>> the slot via enable_slot().
>>
>> Can I assume the last enable_slot() will temporarily re-configure the bridge
>> window so that all other PCI devices' mmio will lose effect at that time point?
> 
> That's likely what would happen.
> The same issue should apply to native PCIe and SHPC hotplug, as they also use
> pci_assign_unassigned_bridge_resources().
> 
> Perhaps drivers have to be taught that PCI tree is being reconfigured or some
> another approach can be used to deal with it.
> Do you have any ideas?

This is not limited to the kernel space. The kernel space may remap/expose the
mmio region to the userspace. The userspace program may directly interacts with
the PCI device as well (DPDK?).

How about stop machine mechanism if we need to touch the PCI bridge window, to
guarantee no CPU is actively accessing the mmio?

Thank you very much!

Dongli Zhang

> 
> I'm comparing with Windows guest, which manages to reconfigure PCI hierarchy
> on the fly. (though I haven't tested that under heavy load with several
> devices on a bridge).
> 
>> Since drivers always kick the doorbell conditionally, they may hang forever.
>>
>> As I have reported, we used to have the similar issue.
>>
>> PCI: Probe bridge window attributes once at enumeration-time
>> https://urldefense.com/v3/__https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=51c48b310183ab6ba5419edfc6a8de889cc04521__;!!ACWV5N9M2RV99hQ!KCs-3SYiAH9t7yzAmSJlDD-YJ7bo0z3Syg9VYF8JJ3JTkYeoSINQD4Tx_7NpDxWeL04FF5lLWlQHrZMsDkoY$ 
>>
>>
>> Therefore, can I assume the issue is not because to re-enable an already-enabled
>> slot, but to touch the bridge window for more than once?
>>
>> Thank you very much!
>>
>> Dongli Zhang
>>
>>>   
>>>> So adding synchronisation and testing
>>>> would take time (not something I'd do this late in the cycle).
>>>>
>>>> So far I'm thinking about adding rw mutex to bridge with the PCI
>>>> hotplug subsystem
>>>> being a writer while scsi scan jobs would be readers and wait till hotplug code
>>>> says it's safe to proceed.
>>>> I plan to work in this direction and give it some testing, unless
>>>> someone has a better idea.  
>>>   
>>>>>  
>>>>>> +
>>>>>> +                                ++nr_hp_slots;
>>>>>>                                 enable_slot(slot, true);
>>>>>>                         }
>>>>>>                 } else {
>>>>>> --  
>>>>>  
>>>   
>>
>
diff mbox series

Patch

diff --git a/drivers/pci/hotplug/acpiphp_glue.c b/drivers/pci/hotplug/acpiphp_glue.c
index 6b11609927d6..30bca2086b24 100644
--- a/drivers/pci/hotplug/acpiphp_glue.c
+++ b/drivers/pci/hotplug/acpiphp_glue.c
@@ -37,6 +37,7 @@ 
 #include <linux/mutex.h>
 #include <linux/slab.h>
 #include <linux/acpi.h>
+#include <linux/delay.h>
 
 #include "../pci.h"
 #include "acpiphp.h"
@@ -700,6 +701,7 @@  static void trim_stale_devices(struct pci_dev *dev)
 static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
 {
 	struct acpiphp_slot *slot;
+        int nr_hp_slots = 0;
 
 	/* Bail out if the bridge is going away. */
 	if (bridge->is_going_away)
@@ -723,6 +725,10 @@  static void acpiphp_check_bridge(struct acpiphp_bridge *bridge)
 
 			/* configure all functions */
 			if (slot->flags != SLOT_ENABLED) {
+				if (nr_hp_slots)
+					msleep(1000);
+
+                                ++nr_hp_slots;
 				enable_slot(slot, true);
 			}
 		} else {