diff mbox series

[v3,2/7] arm64: dts: qcom: sm8150-hdk: enable HDMI output

Message ID 20231215174152.315403-3-dmitry.baryshkov@linaro.org
State Accepted
Commit 73d1d5b153fe143ad53bef3bc089fb1b9b463e5d
Headers show
Series arm64: dts: qcom: sm8150-hdk: enable display output | expand

Commit Message

Dmitry Baryshkov Dec. 15, 2023, 5:40 p.m. UTC
Add DSI outputs and link them to the onboard Lontium LT9611 DSI-to-HDMI
bridge, enabling HDMI output on this board. While adding the display
resources, also drop the headless ("amd,imageon") compat string from the
GPU node, since the board now has output.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts | 128 +++++++++++++++++++++++-
 1 file changed, 123 insertions(+), 5 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
index bb161b536da4..6a036f9ba1c9 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -54,6 +54,17 @@  key-vol-up {
 			gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
 };
 
 &apps_rsc {
@@ -359,12 +370,112 @@  &gmu {
 	status = "okay";
 };
 
+&gpi_dma1 {
+	status = "okay";
+};
+
 &gpu {
-	/*
-	 * NOTE: "amd,imageon" makes Adreno start in headless mode, remove it
-	 * after display support is added on this board.
-	 */
-	compatible = "qcom,adreno-640.1", "qcom,adreno", "amd,imageon";
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	lt9611_codec: hdmi-bridge@3b {
+		compatible = "lontium,lt9611";
+		reg = <0x3b>;
+		#sound-dai-cells = <1>;
+
+		interrupts-extended = <&tlmm 9 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&vreg_s4a_1p8>;
+		vcc-supply = <&vreg_bob>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_irq_pin>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lt9611_b: endpoint {
+					remote-endpoint = <&mdss_dsi1_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l3c_1p2>;
+
+	qcom,dual-dsi-mode;
+	qcom,master-dsi;
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_a>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vreg_l5a_0p875>;
+};
+
+&mdss_dsi1 {
+	vdda-supply = <&vreg_l3c_1p2>;
+
+	qcom,dual-dsi-mode;
+
+	/* DSI1 is slave, so use DSI0 clocks */
+	assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>;
+
+	status = "okay";
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&lt9611_b>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&mdss_dsi1_phy {
+	vdds-supply = <&vreg_l5a_0p875>;
 	status = "okay";
 };
 
@@ -402,6 +513,13 @@  &remoteproc_slpi {
 
 &tlmm {
 	gpio-reserved-ranges = <0 4>, <126 4>;
+
+	lt9611_irq_pin: lt9611-irq-state {
+		pins = "gpio9";
+		function = "gpio";
+		bias-disable;
+	};
+
 };
 
 &uart2 {