| Message ID | 20240112153348.2778-3-quic_nitirawa@quicinc.com |
|---|---|
| State | New |
| Headers | show |
| Series | Refactor phy powerup sequence | expand |
On 12-01-24, 21:03, Nitin Rawat wrote: > Commit 052553af6a31 ("ufs/phy: qcom: Refactor to use phy_init call") > puts enabling regulators & clks, calibrating UFS PHY, starting serdes > and polling PCS ready status into phy_power_on. > > In Current code regulators enable, clks enable, calibrating UFS PHY, > start_serdes and polling PCS_ready_status are part of phy_power_on. > > UFS PHY registers are retained after power collapse, meaning calibrating > UFS PHY, start_serdes and polling PCS_ready_status can be done only when > hba is powered_on, and not needed every time when phy_power_on is called > during resume. Hence keep the code which enables PHY's regulators & clks > in phy_power_on and move the rest steps into phy_calibrate function. > > Refactor the code to enable PHY regulators & clks in phy_power_on and > move rest of the code to phy_calibrate function. > > Co-developed-by: Can Guo <quic_cang@quicinc.com> > Signed-off-by: Can Guo <quic_cang@quicinc.com> > Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com> > Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com> > Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com> > --- > drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 183 +++++++++--------------- > 1 file changed, 67 insertions(+), 116 deletions(-) > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > index 3c2e6255e26f..ae0218738b0b 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > @@ -32,14 +32,15 @@ > /* QPHY_SW_RESET bit */ > #define SW_RESET BIT(0) > /* QPHY_POWER_DOWN_CONTROL */ > -#define SW_PWRDN BIT(0) > +#define SW_PWRUP BIT(0) > +#define SW_PWRDN 0 why change this? so which bit is for PWR control, it is still bit 0 right? > /* QPHY_START_CONTROL bits */ > #define SERDES_START BIT(0) > #define PCS_START BIT(1) > /* QPHY_PCS_READY_STATUS bit */ > #define PCS_READY BIT(0) > > -#define PHY_INIT_COMPLETE_TIMEOUT 10000 > +#define PHY_INIT_COMPLETE_TIMEOUT 1000000 why change timeout? this should be explained in log, even better a individual patch explaining why this was changed > > struct qmp_phy_init_tbl { > unsigned int offset; > @@ -1464,8 +1465,25 @@ static void qmp_ufs_init_registers(struct qmp_ufs *qmp, const struct qmp_phy_cfg > qmp_ufs_pcs_init(qmp, &cfg->tbls_hs_g4); > } > > -static int qmp_ufs_com_init(struct qmp_ufs *qmp) > +static int qmp_ufs_power_off(struct phy *phy) > +{ > + struct qmp_ufs *qmp = phy_get_drvdata(phy); > + const struct qmp_phy_cfg *cfg = qmp->cfg; > + > + /* Put PHY into POWER DOWN state: active low */ > + qphy_clrbits(qmp->pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], > + SW_PWRDN); this will clear the bit, i think you are interpreting this as right which this is not > + > + clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); > + > + regulator_bulk_disable(cfg->num_vregs, qmp->vregs); > + > + return 0; > +} > + > +static int qmp_ufs_power_on(struct phy *phy) > { > + struct qmp_ufs *qmp = phy_get_drvdata(phy); > const struct qmp_phy_cfg *cfg = qmp->cfg; > void __iomem *pcs = qmp->pcs; > int ret; > @@ -1480,8 +1498,7 @@ static int qmp_ufs_com_init(struct qmp_ufs *qmp) > if (ret) > goto err_disable_regulators; > > - qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], SW_PWRDN); > - > + qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], SW_PWRUP); > return 0; > > err_disable_regulators: > @@ -1490,61 +1507,7 @@ static int qmp_ufs_com_init(struct qmp_ufs *qmp) > return ret; > } > > -static int qmp_ufs_com_exit(struct qmp_ufs *qmp) > -{ > - const struct qmp_phy_cfg *cfg = qmp->cfg; > - > - reset_control_assert(qmp->ufs_reset); > - > - clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); > - > - regulator_bulk_disable(cfg->num_vregs, qmp->vregs); > - > - return 0; > -} > - > -static int qmp_ufs_init(struct phy *phy) > -{ > - struct qmp_ufs *qmp = phy_get_drvdata(phy); > - const struct qmp_phy_cfg *cfg = qmp->cfg; > - int ret; > - dev_vdbg(qmp->dev, "Initializing QMP phy\n"); > - > - if (cfg->no_pcs_sw_reset) { > - /* > - * Get UFS reset, which is delayed until now to avoid a > - * circular dependency where UFS needs its PHY, but the PHY > - * needs this UFS reset. > - */ > - if (!qmp->ufs_reset) { > - qmp->ufs_reset = > - devm_reset_control_get_exclusive(qmp->dev, > - "ufsphy"); > - > - if (IS_ERR(qmp->ufs_reset)) { > - ret = PTR_ERR(qmp->ufs_reset); > - dev_err(qmp->dev, > - "failed to get UFS reset: %d\n", > - ret); > - > - qmp->ufs_reset = NULL; > - return ret; > - } > - } > - > - ret = reset_control_assert(qmp->ufs_reset); > - if (ret) > - return ret; > - } > - > - ret = qmp_ufs_com_init(qmp); > - if (ret) > - return ret; > - > - return 0; > -} > - > -static int qmp_ufs_power_on(struct phy *phy) > +static int qmp_ufs_phy_calibrate(struct phy *phy) > { > struct qmp_ufs *qmp = phy_get_drvdata(phy); > const struct qmp_phy_cfg *cfg = qmp->cfg; > @@ -1553,11 +1516,21 @@ static int qmp_ufs_power_on(struct phy *phy) > unsigned int val; > int ret; > > + qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], SW_PWRUP); > + > + ret = reset_control_assert(qmp->ufs_reset); > + if (ret) { > + dev_err(qmp->dev, "Failed to assert UFS PHY reset %d\n", ret); > + return ret; > + } > + > qmp_ufs_init_registers(qmp, cfg); > > ret = reset_control_deassert(qmp->ufs_reset); > - if (ret) > + if (ret) { > + dev_err(qmp->dev, "Failed to deassert UFS PHY reset %d\n", ret); > return ret; > + } > > /* Pull PHY out of reset state */ > if (!cfg->no_pcs_sw_reset) > @@ -1577,59 +1550,6 @@ static int qmp_ufs_power_on(struct phy *phy) > return 0; > } > > -static int qmp_ufs_power_off(struct phy *phy) > -{ > - struct qmp_ufs *qmp = phy_get_drvdata(phy); > - const struct qmp_phy_cfg *cfg = qmp->cfg; > - > - /* PHY reset */ > - if (!cfg->no_pcs_sw_reset) > - qphy_setbits(qmp->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET); > - > - /* stop SerDes */ > - qphy_clrbits(qmp->pcs, cfg->regs[QPHY_START_CTRL], SERDES_START); > - > - /* Put PHY into POWER DOWN state: active low */ > - qphy_clrbits(qmp->pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], > - SW_PWRDN); > - > - return 0; > -} > - > -static int qmp_ufs_exit(struct phy *phy) > -{ > - struct qmp_ufs *qmp = phy_get_drvdata(phy); > - > - qmp_ufs_com_exit(qmp); > - > - return 0; > -} > - > -static int qmp_ufs_enable(struct phy *phy) > -{ > - int ret; > - > - ret = qmp_ufs_init(phy); > - if (ret) > - return ret; > - > - ret = qmp_ufs_power_on(phy); > - if (ret) > - qmp_ufs_exit(phy); > - > - return ret; > -} > - > -static int qmp_ufs_disable(struct phy *phy) > -{ > - int ret; > - > - ret = qmp_ufs_power_off(phy); > - if (ret) > - return ret; > - return qmp_ufs_exit(phy); > -} > - > static int qmp_ufs_set_mode(struct phy *phy, enum phy_mode mode, int submode) > { > struct qmp_ufs *qmp = phy_get_drvdata(phy); > @@ -1641,9 +1561,10 @@ static int qmp_ufs_set_mode(struct phy *phy, enum phy_mode mode, int submode) > } > > static const struct phy_ops qcom_qmp_ufs_phy_ops = { > - .power_on = qmp_ufs_enable, > - .power_off = qmp_ufs_disable, > + .power_on = qmp_ufs_power_on, > + .power_off = qmp_ufs_power_off, > .set_mode = qmp_ufs_set_mode, > + .calibrate = qmp_ufs_phy_calibrate, > .owner = THIS_MODULE, > }; > > @@ -1809,6 +1730,32 @@ static int qmp_ufs_parse_dt(struct qmp_ufs *qmp) > return 0; > } > > +static int qmp_ufs_get_phy_reset(struct qmp_ufs *qmp) > +{ > + const struct qmp_phy_cfg *cfg = qmp->cfg; > + int ret; > + > + if (!cfg->no_pcs_sw_reset) > + return 0; > + > + /* > + * Get UFS reset, which is delayed until now to avoid a > + * circular dependency where UFS needs its PHY, but the PHY > + * needs this UFS reset. > + */ > + > + qmp->ufs_reset = devm_reset_control_get_exclusive(qmp->dev, > + "ufsphy"); > + if (IS_ERR(qmp->ufs_reset)) { > + ret = PTR_ERR(qmp->ufs_reset); > + dev_err(qmp->dev, "failed to get UFS reset: %d\n", ret); > + qmp->ufs_reset = NULL; > + return ret; > + } > + > + return 0; > +} > + > static int qmp_ufs_probe(struct platform_device *pdev) > { > struct device *dev = &pdev->dev; > @@ -1835,6 +1782,10 @@ static int qmp_ufs_probe(struct platform_device *pdev) > if (ret) > return ret; > > + ret = qmp_ufs_get_phy_reset(qmp); > + if (ret) > + return ret; > + I think this patch should be split to moving code around to helper fn and then add logic for moving power up/down calls, pls dont mix everything in single patch > /* Check for legacy binding with child node. */ > np = of_get_next_available_child(dev->of_node, NULL); > if (np) { > -- > 2.43.0
On Fri, Jan 12, 2024 at 09:03:48PM +0530, Nitin Rawat wrote: > Commit 052553af6a31 ("ufs/phy: qcom: Refactor to use phy_init call") > puts enabling regulators & clks, calibrating UFS PHY, starting serdes > and polling PCS ready status into phy_power_on. > > In Current code regulators enable, clks enable, calibrating UFS PHY, > start_serdes and polling PCS_ready_status are part of phy_power_on. > > UFS PHY registers are retained after power collapse, meaning calibrating > UFS PHY, start_serdes and polling PCS_ready_status can be done only when > hba is powered_on, and not needed every time when phy_power_on is called > during resume. Hence keep the code which enables PHY's regulators & clks > in phy_power_on and move the rest steps into phy_calibrate function. > > Refactor the code to enable PHY regulators & clks in phy_power_on and > move rest of the code to phy_calibrate function. > This patch should come before UFS patch since you are introducing the calibrate() callback here only. > Co-developed-by: Can Guo <quic_cang@quicinc.com> > Signed-off-by: Can Guo <quic_cang@quicinc.com> > Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com> > Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com> > Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com> > --- > drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 183 +++++++++--------------- > 1 file changed, 67 insertions(+), 116 deletions(-) > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > index 3c2e6255e26f..ae0218738b0b 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > @@ -32,14 +32,15 @@ > /* QPHY_SW_RESET bit */ > #define SW_RESET BIT(0) > /* QPHY_POWER_DOWN_CONTROL */ > -#define SW_PWRDN BIT(0) > +#define SW_PWRUP BIT(0) > +#define SW_PWRDN 0 Why 0? > /* QPHY_START_CONTROL bits */ > #define SERDES_START BIT(0) > #define PCS_START BIT(1) > /* QPHY_PCS_READY_STATUS bit */ > #define PCS_READY BIT(0) > > -#define PHY_INIT_COMPLETE_TIMEOUT 10000 > +#define PHY_INIT_COMPLETE_TIMEOUT 1000000 Why? This is not mentioned in the commit message. If it is not related to this refactoring, then it should be a separate patch with justification. > > struct qmp_phy_init_tbl { > unsigned int offset; > @@ -1464,8 +1465,25 @@ static void qmp_ufs_init_registers(struct qmp_ufs *qmp, const struct qmp_phy_cfg > qmp_ufs_pcs_init(qmp, &cfg->tbls_hs_g4); > } > > -static int qmp_ufs_com_init(struct qmp_ufs *qmp) > +static int qmp_ufs_power_off(struct phy *phy) > +{ > + struct qmp_ufs *qmp = phy_get_drvdata(phy); > + const struct qmp_phy_cfg *cfg = qmp->cfg; > + > + /* Put PHY into POWER DOWN state: active low */ > + qphy_clrbits(qmp->pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], > + SW_PWRDN); > + > + clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); > + > + regulator_bulk_disable(cfg->num_vregs, qmp->vregs); > + > + return 0; > +} > + > +static int qmp_ufs_power_on(struct phy *phy) > { > + struct qmp_ufs *qmp = phy_get_drvdata(phy); > const struct qmp_phy_cfg *cfg = qmp->cfg; > void __iomem *pcs = qmp->pcs; > int ret; > @@ -1480,8 +1498,7 @@ static int qmp_ufs_com_init(struct qmp_ufs *qmp) > if (ret) > goto err_disable_regulators; > > - qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], SW_PWRDN); > - > + qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], SW_PWRUP); Newline please. As mentioned above, why can't you use existing SW_PWRDN macro. > return 0; > > err_disable_regulators: > @@ -1490,61 +1507,7 @@ static int qmp_ufs_com_init(struct qmp_ufs *qmp) > return ret; > } > [...] > +static int qmp_ufs_get_phy_reset(struct qmp_ufs *qmp) > +{ > + const struct qmp_phy_cfg *cfg = qmp->cfg; > + int ret; > + > + if (!cfg->no_pcs_sw_reset) > + return 0; > + > + /* > + * Get UFS reset, which is delayed until now to avoid a > + * circular dependency where UFS needs its PHY, but the PHY > + * needs this UFS reset. > + */ > + > + qmp->ufs_reset = devm_reset_control_get_exclusive(qmp->dev, > + "ufsphy"); You have moved this to probe from power_on() without any justification. What about the circular dependency mentioned in the comment. - Mani
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c index 3c2e6255e26f..ae0218738b0b 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c @@ -32,14 +32,15 @@ /* QPHY_SW_RESET bit */ #define SW_RESET BIT(0) /* QPHY_POWER_DOWN_CONTROL */ -#define SW_PWRDN BIT(0) +#define SW_PWRUP BIT(0) +#define SW_PWRDN 0 /* QPHY_START_CONTROL bits */ #define SERDES_START BIT(0) #define PCS_START BIT(1) /* QPHY_PCS_READY_STATUS bit */ #define PCS_READY BIT(0) -#define PHY_INIT_COMPLETE_TIMEOUT 10000 +#define PHY_INIT_COMPLETE_TIMEOUT 1000000 struct qmp_phy_init_tbl { unsigned int offset; @@ -1464,8 +1465,25 @@ static void qmp_ufs_init_registers(struct qmp_ufs *qmp, const struct qmp_phy_cfg qmp_ufs_pcs_init(qmp, &cfg->tbls_hs_g4); } -static int qmp_ufs_com_init(struct qmp_ufs *qmp) +static int qmp_ufs_power_off(struct phy *phy) +{ + struct qmp_ufs *qmp = phy_get_drvdata(phy); + const struct qmp_phy_cfg *cfg = qmp->cfg; + + /* Put PHY into POWER DOWN state: active low */ + qphy_clrbits(qmp->pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], + SW_PWRDN); + + clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); + + regulator_bulk_disable(cfg->num_vregs, qmp->vregs); + + return 0; +} + +static int qmp_ufs_power_on(struct phy *phy) { + struct qmp_ufs *qmp = phy_get_drvdata(phy); const struct qmp_phy_cfg *cfg = qmp->cfg; void __iomem *pcs = qmp->pcs; int ret; @@ -1480,8 +1498,7 @@ static int qmp_ufs_com_init(struct qmp_ufs *qmp) if (ret) goto err_disable_regulators; - qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], SW_PWRDN); - + qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], SW_PWRUP); return 0; err_disable_regulators: @@ -1490,61 +1507,7 @@ static int qmp_ufs_com_init(struct qmp_ufs *qmp) return ret; } -static int qmp_ufs_com_exit(struct qmp_ufs *qmp) -{ - const struct qmp_phy_cfg *cfg = qmp->cfg; - - reset_control_assert(qmp->ufs_reset); - - clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); - - regulator_bulk_disable(cfg->num_vregs, qmp->vregs); - - return 0; -} - -static int qmp_ufs_init(struct phy *phy) -{ - struct qmp_ufs *qmp = phy_get_drvdata(phy); - const struct qmp_phy_cfg *cfg = qmp->cfg; - int ret; - dev_vdbg(qmp->dev, "Initializing QMP phy\n"); - - if (cfg->no_pcs_sw_reset) { - /* - * Get UFS reset, which is delayed until now to avoid a - * circular dependency where UFS needs its PHY, but the PHY - * needs this UFS reset. - */ - if (!qmp->ufs_reset) { - qmp->ufs_reset = - devm_reset_control_get_exclusive(qmp->dev, - "ufsphy"); - - if (IS_ERR(qmp->ufs_reset)) { - ret = PTR_ERR(qmp->ufs_reset); - dev_err(qmp->dev, - "failed to get UFS reset: %d\n", - ret); - - qmp->ufs_reset = NULL; - return ret; - } - } - - ret = reset_control_assert(qmp->ufs_reset); - if (ret) - return ret; - } - - ret = qmp_ufs_com_init(qmp); - if (ret) - return ret; - - return 0; -} - -static int qmp_ufs_power_on(struct phy *phy) +static int qmp_ufs_phy_calibrate(struct phy *phy) { struct qmp_ufs *qmp = phy_get_drvdata(phy); const struct qmp_phy_cfg *cfg = qmp->cfg; @@ -1553,11 +1516,21 @@ static int qmp_ufs_power_on(struct phy *phy) unsigned int val; int ret; + qphy_setbits(pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], SW_PWRUP); + + ret = reset_control_assert(qmp->ufs_reset); + if (ret) { + dev_err(qmp->dev, "Failed to assert UFS PHY reset %d\n", ret); + return ret; + } + qmp_ufs_init_registers(qmp, cfg); ret = reset_control_deassert(qmp->ufs_reset); - if (ret) + if (ret) { + dev_err(qmp->dev, "Failed to deassert UFS PHY reset %d\n", ret); return ret; + } /* Pull PHY out of reset state */ if (!cfg->no_pcs_sw_reset) @@ -1577,59 +1550,6 @@ static int qmp_ufs_power_on(struct phy *phy) return 0; } -static int qmp_ufs_power_off(struct phy *phy) -{ - struct qmp_ufs *qmp = phy_get_drvdata(phy); - const struct qmp_phy_cfg *cfg = qmp->cfg; - - /* PHY reset */ - if (!cfg->no_pcs_sw_reset) - qphy_setbits(qmp->pcs, cfg->regs[QPHY_SW_RESET], SW_RESET); - - /* stop SerDes */ - qphy_clrbits(qmp->pcs, cfg->regs[QPHY_START_CTRL], SERDES_START); - - /* Put PHY into POWER DOWN state: active low */ - qphy_clrbits(qmp->pcs, cfg->regs[QPHY_PCS_POWER_DOWN_CONTROL], - SW_PWRDN); - - return 0; -} - -static int qmp_ufs_exit(struct phy *phy) -{ - struct qmp_ufs *qmp = phy_get_drvdata(phy); - - qmp_ufs_com_exit(qmp); - - return 0; -} - -static int qmp_ufs_enable(struct phy *phy) -{ - int ret; - - ret = qmp_ufs_init(phy); - if (ret) - return ret; - - ret = qmp_ufs_power_on(phy); - if (ret) - qmp_ufs_exit(phy); - - return ret; -} - -static int qmp_ufs_disable(struct phy *phy) -{ - int ret; - - ret = qmp_ufs_power_off(phy); - if (ret) - return ret; - return qmp_ufs_exit(phy); -} - static int qmp_ufs_set_mode(struct phy *phy, enum phy_mode mode, int submode) { struct qmp_ufs *qmp = phy_get_drvdata(phy); @@ -1641,9 +1561,10 @@ static int qmp_ufs_set_mode(struct phy *phy, enum phy_mode mode, int submode) } static const struct phy_ops qcom_qmp_ufs_phy_ops = { - .power_on = qmp_ufs_enable, - .power_off = qmp_ufs_disable, + .power_on = qmp_ufs_power_on, + .power_off = qmp_ufs_power_off, .set_mode = qmp_ufs_set_mode, + .calibrate = qmp_ufs_phy_calibrate, .owner = THIS_MODULE, }; @@ -1809,6 +1730,32 @@ static int qmp_ufs_parse_dt(struct qmp_ufs *qmp) return 0; } +static int qmp_ufs_get_phy_reset(struct qmp_ufs *qmp) +{ + const struct qmp_phy_cfg *cfg = qmp->cfg; + int ret; + + if (!cfg->no_pcs_sw_reset) + return 0; + + /* + * Get UFS reset, which is delayed until now to avoid a + * circular dependency where UFS needs its PHY, but the PHY + * needs this UFS reset. + */ + + qmp->ufs_reset = devm_reset_control_get_exclusive(qmp->dev, + "ufsphy"); + if (IS_ERR(qmp->ufs_reset)) { + ret = PTR_ERR(qmp->ufs_reset); + dev_err(qmp->dev, "failed to get UFS reset: %d\n", ret); + qmp->ufs_reset = NULL; + return ret; + } + + return 0; +} + static int qmp_ufs_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; @@ -1835,6 +1782,10 @@ static int qmp_ufs_probe(struct platform_device *pdev) if (ret) return ret; + ret = qmp_ufs_get_phy_reset(qmp); + if (ret) + return ret; + /* Check for legacy binding with child node. */ np = of_get_next_available_child(dev->of_node, NULL); if (np) {
Commit 052553af6a31 ("ufs/phy: qcom: Refactor to use phy_init call") puts enabling regulators & clks, calibrating UFS PHY, starting serdes and polling PCS ready status into phy_power_on. In Current code regulators enable, clks enable, calibrating UFS PHY, start_serdes and polling PCS_ready_status are part of phy_power_on. UFS PHY registers are retained after power collapse, meaning calibrating UFS PHY, start_serdes and polling PCS_ready_status can be done only when hba is powered_on, and not needed every time when phy_power_on is called during resume. Hence keep the code which enables PHY's regulators & clks in phy_power_on and move the rest steps into phy_calibrate function. Refactor the code to enable PHY regulators & clks in phy_power_on and move rest of the code to phy_calibrate function. Co-developed-by: Can Guo <quic_cang@quicinc.com> Signed-off-by: Can Guo <quic_cang@quicinc.com> Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com> Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com> Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com> --- drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 183 +++++++++--------------- 1 file changed, 67 insertions(+), 116 deletions(-) -- 2.43.0