@@ -78,6 +78,8 @@
#define S3C64XX_SPI_INT_RX_FIFORDY_EN BIT(1)
#define S3C64XX_SPI_INT_TX_FIFORDY_EN BIT(0)
+#define S3C64XX_SPI_ST_RX_FIFO_LVL GENMASK(23, 15)
+#define S3C64XX_SPI_ST_TX_FIFO_LVL GENMASK(14, 6)
#define S3C64XX_SPI_ST_RX_OVERRUN_ERR BIT(5)
#define S3C64XX_SPI_ST_RX_UNDERRUN_ERR BIT(4)
#define S3C64XX_SPI_ST_TX_OVERRUN_ERR BIT(3)
@@ -108,9 +110,6 @@
#define FIFO_LVL_MASK(i) ((i)->port_conf->fifo_lvl_mask[i->port_id])
#define S3C64XX_SPI_ST_TX_DONE(v, i) (((v) & \
(1 << (i)->port_conf->tx_st_done)) ? 1 : 0)
-#define TX_FIFO_LVL(v, i) (((v) >> 6) & FIFO_LVL_MASK(i))
-#define RX_FIFO_LVL(v, i) (((v) >> (i)->port_conf->rx_lvl_offset) & \
- FIFO_LVL_MASK(i))
#define FIFO_DEPTH(i) ((FIFO_LVL_MASK(i) >> 1) + 1)
#define S3C64XX_SPI_POLLING_SIZE 32
@@ -219,7 +218,7 @@ static void s3c64xx_flush_fifo(struct s3c64xx_spi_driver_data *sdd)
loops = msecs_to_loops(1);
do {
val = readl(regs + S3C64XX_SPI_STATUS);
- } while (TX_FIFO_LVL(val, sdd) && loops--);
+ } while (FIELD_GET(S3C64XX_SPI_ST_TX_FIFO_LVL, val) && loops--);
if (loops == 0)
dev_warn(&sdd->pdev->dev, "Timed out flushing TX FIFO\n");
@@ -228,7 +227,7 @@ static void s3c64xx_flush_fifo(struct s3c64xx_spi_driver_data *sdd)
loops = msecs_to_loops(1);
do {
val = readl(regs + S3C64XX_SPI_STATUS);
- if (RX_FIFO_LVL(val, sdd))
+ if (FIELD_GET(S3C64XX_SPI_ST_RX_FIFO_LVL, val))
readl(regs + S3C64XX_SPI_RX_DATA);
else
break;
@@ -499,10 +498,11 @@ static u32 s3c64xx_spi_wait_for_timeout(struct s3c64xx_spi_driver_data *sdd,
do {
status = readl(regs + S3C64XX_SPI_STATUS);
- } while (RX_FIFO_LVL(status, sdd) < max_fifo && --val);
+ } while (FIELD_GET(S3C64XX_SPI_ST_RX_FIFO_LVL, status) < max_fifo &&
+ --val);
/* return the actual received data length */
- return RX_FIFO_LVL(status, sdd);
+ return FIELD_GET(S3C64XX_SPI_ST_RX_FIFO_LVL, status);
}
static int s3c64xx_wait_for_dma(struct s3c64xx_spi_driver_data *sdd,
@@ -533,7 +533,7 @@ static int s3c64xx_wait_for_dma(struct s3c64xx_spi_driver_data *sdd,
if (val && !xfer->rx_buf) {
val = msecs_to_loops(10);
status = readl(regs + S3C64XX_SPI_STATUS);
- while ((TX_FIFO_LVL(status, sdd)
+ while ((FIELD_GET(S3C64XX_SPI_ST_TX_FIFO_LVL, status)
|| !S3C64XX_SPI_ST_TX_DONE(status, sdd))
&& --val) {
cpu_relax();
@@ -568,7 +568,7 @@ static int s3c64xx_wait_for_pio(struct s3c64xx_spi_driver_data *sdd,
/* sleep during signal transfer time */
status = readl(regs + S3C64XX_SPI_STATUS);
- if (RX_FIFO_LVL(status, sdd) < xfer->len)
+ if (FIELD_GET(S3C64XX_SPI_ST_RX_FIFO_LVL, status) < xfer->len)
usleep_range(time_us / 2, time_us);
if (use_irq) {
@@ -580,7 +580,8 @@ static int s3c64xx_wait_for_pio(struct s3c64xx_spi_driver_data *sdd,
val = msecs_to_loops(ms);
do {
status = readl(regs + S3C64XX_SPI_STATUS);
- } while (RX_FIFO_LVL(status, sdd) < xfer->len && --val);
+ } while (FIELD_GET(S3C64XX_SPI_ST_RX_FIFO_LVL, status) < xfer->len &&
+ --val);
if (!val)
return -EIO;
SPI_STATUSn.{RX, TX}_FIFO_LVL fields show the data level in the RX and TX FIFOs. The IP supports FIFOs from 8 to 256 bytes, but apart from the MODE_CFG.{RX, TX}_RDY_LVL fields that configure the {RX, TX} FIFO trigger level in the interrupt mode, there's nothing in the registers that configure the FIFOs depth. Is the responsibility of the SoC that integrates the IP to dictate the FIFO depth and of the SPI driver to make sure it doesn't bypass the FIFO length. {RX, TX}_FIFO_LVL was used to pass the FIFO length information based on the IP configuration in the SoC. Its value was defined so that it includes the entire FIFO length. For example, if one wanted to specify a 64 FIFO length (0x40), it wold configure the FIFO level to 127 (0x7f). This is not only wrong, because it doesn't respect the IP's register fields, it's also misleading. Use the full mask for the SPI_STATUSn.{RX, TX}_FIFO_LVL fields. No change in functionality is expected. Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> --- drivers/spi/spi-s3c64xx.c | 21 +++++++++++---------- 1 file changed, 11 insertions(+), 10 deletions(-)