@@ -731,22 +731,14 @@ &pcie4 {
pinctrl-0 = <&pcie4_default>;
status = "okay";
+};
- pcie@0 {
- device_type = "pci";
- reg = <0x0 0x0 0x0 0x0 0x0>;
- #address-cells = <3>;
- #size-cells = <2>;
- ranges;
-
- bus-range = <0x01 0xff>;
-
- wifi@0 {
- compatible = "pci17cb,1103";
- reg = <0x10000 0x0 0x0 0x0 0x0>;
+&pcie4_port0 {
+ wifi@0 {
+ compatible = "pci17cb,1103";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
- qcom,ath11k-calibration-variant = "LE_X13S";
- };
+ qcom,ath11k-calibration-variant = "LE_X13S";
};
};
@@ -1779,6 +1779,16 @@ pcie4: pcie@1c00000 {
phy-names = "pciephy";
status = "disabled";
+
+ pcie4_port0: pcie@0 {
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie4_phy: phy@1c06000 {
@@ -1877,6 +1887,16 @@ pcie3b: pcie@1c08000 {
phy-names = "pciephy";
status = "disabled";
+
+ pcie3b_port0: pcie@0 {
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie3b_phy: phy@1c0e000 {
@@ -1975,6 +1995,16 @@ pcie3a: pcie@1c10000 {
phy-names = "pciephy";
status = "disabled";
+
+ pcie3a_port0: pcie@0 {
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie3a_phy: phy@1c14000 {
@@ -2076,6 +2106,16 @@ pcie2b: pcie@1c18000 {
phy-names = "pciephy";
status = "disabled";
+
+ pcie2b_port0: pcie@0 {
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie2b_phy: phy@1c1e000 {
@@ -2174,6 +2214,16 @@ pcie2a: pcie@1c20000 {
phy-names = "pciephy";
status = "disabled";
+
+ pcie2a_port0: pcie@0 {
+ device_type = "pci";
+ reg = <0x0 0x0 0x0 0x0 0x0>;
+ bus-range = <0x01 0xff>;
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+ };
};
pcie2a_phy: phy@1c24000 {
On Qcom SoCs, the PCIe host bridge is connected to a single PCIe bridge for each controller instance. Hence, add a node to represent the bridge. While at it, let's remove the bridge properties from board dts as they are now redundant. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> --- .../dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 20 +++------ arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 50 ++++++++++++++++++++++ 2 files changed, 56 insertions(+), 14 deletions(-)