diff mbox series

[2/2] arm64: dts: qcom: qcm6490-fairphone-fp5: Configure PM8008 regulators

Message ID 20240621-fp4-fp5-pm8008-v1-2-dbedcd6f00f1@fairphone.com
State Accepted
Commit 2cf5ec58e87bf4df1b360ab45c047d2b311930c8
Headers show
Series [1/2] arm64: dts: qcom: sm7225-fairphone-fp4: Configure PM8008 regulators | expand

Commit Message

Luca Weiss June 21, 2024, 8:42 a.m. UTC
PM8008 regulators are used for the cameras found on FP5. Configure the
chip and its voltages.

Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
---
 arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts | 105 ++++++++++++++++++++-
 1 file changed, 104 insertions(+), 1 deletion(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts b/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts
index 25ed74d4ebd2..765585b0d09e 100644
--- a/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts
+++ b/arch/arm64/boot/dts/qcom/qcm6490-fairphone-fp5.dts
@@ -207,6 +207,25 @@  active-config0 {
 			};
 		};
 
+		pm8008-thermal {
+			polling-delay-passive = <100>;
+			thermal-sensors = <&pm8008>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
 		quiet-thermal {
 			polling-delay-passive = <0>;
 
@@ -522,7 +541,76 @@  &gpi_dma1 {
 &i2c1 {
 	status = "okay";
 
-	/* PM8008 PMIC @ 8 and 9 */
+	pm8008: pmic@8 {
+		compatible = "qcom,pm8008";
+		reg = <0x8>;
+
+		interrupts-extended = <&tlmm 25 IRQ_TYPE_EDGE_RISING>;
+		reset-gpios = <&pm8350c_gpios 3 GPIO_ACTIVE_LOW>;
+
+		vdd-l1-l2-supply = <&vreg_s8b>;
+		vdd-l3-l4-supply = <&vreg_bob>;
+		vdd-l5-supply = <&vreg_bob>;
+		vdd-l6-supply = <&vreg_s1b>;
+		vdd-l7-supply = <&vreg_bob>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pm8008_int_default>, <&pm8008_reset_n_default>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-ranges = <&pm8008 0 0 2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		#thermal-sensor-cells = <0>;
+
+		regulators {
+			vreg_l1p: ldo1 {
+				regulator-name = "vreg_l1p";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			vreg_l2p: ldo2 {
+				regulator-name = "vreg_l2p";
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <1152000>;
+			};
+
+			vreg_l3p: ldo3 {
+				regulator-name = "vreg_l3p";
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			vreg_l4p: ldo4 {
+				regulator-name = "vreg_l4p";
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <2900000>;
+			};
+
+			vreg_l5p: ldo5 {
+				regulator-name = "vreg_l5p";
+				regulator-min-microvolt = <2704000>;
+				regulator-max-microvolt = <2900000>;
+			};
+
+			vreg_l6p: ldo6 {
+				regulator-name = "vreg_l6p";
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1904000>;
+			};
+
+			vreg_l7p: ldo7 {
+				regulator-name = "vreg_l7p";
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <3000000>;
+			};
+		};
+	};
+
 	/* Pixelworks @ 26 */
 	/* FSA4480 USB audio switch @ 42 */
 	/* AW86927FCR haptics @ 5a */
@@ -653,6 +741,14 @@  wide-rfc-therm@4 {
 	};
 };
 
+&pm8350c_gpios {
+	pm8008_reset_n_default: pm8008-reset-n-default-state {
+		pins = "gpio3";
+		function = PMIC_GPIO_FUNC_NORMAL;
+		bias-pull-down;
+	};
+};
+
 &pmk8350_rtc {
 	status = "okay";
 };
@@ -810,6 +906,13 @@  hall_sensor_default: hall-sensor-default-state {
 		bias-pull-up;
 	};
 
+	pm8008_int_default: pm8008-int-default-state {
+		pins = "gpio25";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	qup_uart7_sleep_cts: qup-uart7-sleep-cts-state {
 		pins = "gpio28";
 		function = "gpio";