diff mbox

[v5] PCI: qcom: add support to msm8996 PCIe controller

Message ID 1479381146-12908-1-git-send-email-srinivas.kandagatla@linaro.org
State Superseded
Headers show

Commit Message

Srinivas Kandagatla Nov. 17, 2016, 11:12 a.m. UTC
This patch adds support to msm8996/apq8096 PCIe, MSM8996 supports
Gen 1/2, One lane, 3 PCIe root-complex with support to MSI and
legacy interrupts and it conforms to PCI Express Base 2.1 specification.

This patch adds post_init callback to qcom_pcie_ops, as this is PCIe
pipe clocks are only setup after the phy is powered on.
It also adds ltssm_enable callback as it is very much different to other
supported SOCs in the driver.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>

Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>

---
 Changes since v5:
 	- No code changes.
	- s/pcie/PCIe in change log based on Rob's comments.

 .../devicetree/bindings/pci/qcom,pcie.txt          |  67 +++++++-
 drivers/pci/host/pcie-qcom.c                       | 175 ++++++++++++++++++++-
 2 files changed, 236 insertions(+), 6 deletions(-)

-- 
2.10.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
index 4059a6f..141d8c3 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
@@ -7,6 +7,7 @@ 
 			- "qcom,pcie-ipq8064" for ipq8064
 			- "qcom,pcie-apq8064" for apq8064
 			- "qcom,pcie-apq8084" for apq8084
+			- "qcom,pcie-msm8996" for msm8996 or apq8096
 
 - reg:
 	Usage: required
@@ -92,6 +93,17 @@ 
 			- "aux"		Auxiliary (AUX) clock
 			- "bus_master"	Master AXI clock
 			- "bus_slave"	Slave AXI clock
+
+- clock-names:
+	Usage: required for msm8996/apq8096
+	Value type: <stringlist>
+	Definition: Should contain the following entries
+			- "pipe"	Pipe Clock driving internal logic.
+			- "aux"		Auxiliary (AUX) clock.
+			- "cfg"		Configuration clk.
+			- "bus_master"	Master AXI clock.
+			- "bus_slave"	Slave AXI clock.
+
 - resets:
 	Usage: required
 	Value type: <prop-encoded-array>
@@ -115,7 +127,7 @@ 
 			- "core" Core reset
 
 - power-domains:
-	Usage: required for apq8084
+	Usage: required for apq8084 and msm8996/apq8096
 	Value type: <prop-encoded-array>
 	Definition: A phandle and power domain specifier pair to the
 		    power domain which is responsible for collapsing
@@ -231,3 +243,56 @@ 
 		pinctrl-0 = <&pcie0_pins_default>;
 		pinctrl-names = "default";
 	};
+
+* Example for apq8096:
+
+	pcie@608000{
+		compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
+		power-domains = <&gcc PCIE1_GDSC>;
+		bus-range = <0x00 0xff>;
+		num-lanes = <1>;
+
+		reg = <0x00608000 0x2000>,
+		      <0x0d000000 0xf1d>,
+		      <0x0d000f20 0xa8>,
+		      <0x0d100000 0x100000>;
+
+		reg-names = "parf", "dbi", "elbi", "config";
+
+		phys = <&pcie_phy 1>;
+		phy-names = "pciephy";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>,
+			<0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>;
+
+		interrupts = <GIC_SPI 413 IRQ_TYPE_NONE>;
+		interrupt-names = "msi";
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0x7>;
+		interrupt-map = <0 0 0 1 &intc 0 272 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+				<0 0 0 2 &intc 0 273 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+				<0 0 0 3 &intc 0 274 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+				<0 0 0 4 &intc 0 275 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pcie1_clkreq_default &pcie1_perst_default &pcie1_wake_default>;
+		pinctrl-1 = <&pcie1_clkreq_sleep &pcie1_perst_default &pcie1_wake_sleep>;
+
+		vdda-1p8-supply = <&pm8994_l12>;
+		vdda-supply = <&pm8994_l28>;
+		linux,pci-domain = <1>;
+
+		clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
+			<&gcc GCC_PCIE_1_AUX_CLK>,
+			<&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+			<&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+			<&gcc GCC_PCIE_1_SLV_AXI_CLK>;
+
+		clock-names =  "pipe",
+				"aux",
+				"cfg",
+				"bus_master",
+				"bus_slave";
+	};
diff --git a/drivers/pci/host/pcie-qcom.c b/drivers/pci/host/pcie-qcom.c
index 3593640..25c5556 100644
--- a/drivers/pci/host/pcie-qcom.c
+++ b/drivers/pci/host/pcie-qcom.c
@@ -36,11 +36,17 @@ 
 
 #include "pcie-designware.h"
 
+#define PCIE20_PARF_SYS_CTRL			0x00
 #define PCIE20_PARF_PHY_CTRL			0x40
 #define PCIE20_PARF_PHY_REFCLK			0x4C
 #define PCIE20_PARF_DBI_BASE_ADDR		0x168
 #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE		0x16c
+#define PCIE20_PARF_MHI_CLOCK_RESET_CTRL	0x174
 #define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT	0x178
+#define PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2	0x1A8
+#define PCIE20_PARF_LTSSM			0x1B0
+#define PCIE20_PARF_SID_OFFSET			0x234
+#define PCIE20_PARF_BDF_TRANSLATE_CFG		0x24C
 
 #define PCIE20_ELBI_SYS_CTRL			0x04
 #define PCIE20_ELBI_SYS_CTRL_LT_ENABLE		BIT(0)
@@ -72,9 +78,18 @@  struct qcom_pcie_resources_v1 {
 	struct regulator *vdda;
 };
 
+struct qcom_pcie_resources_v2 {
+	struct clk *aux_clk;
+	struct clk *master_clk;
+	struct clk *slave_clk;
+	struct clk *cfg_clk;
+	struct clk *pipe_clk;
+};
+
 union qcom_pcie_resources {
 	struct qcom_pcie_resources_v0 v0;
 	struct qcom_pcie_resources_v1 v1;
+	struct qcom_pcie_resources_v2 v2;
 };
 
 struct qcom_pcie;
@@ -82,7 +97,9 @@  struct qcom_pcie;
 struct qcom_pcie_ops {
 	int (*get_resources)(struct qcom_pcie *pcie);
 	int (*init)(struct qcom_pcie *pcie);
+	int (*post_init)(struct qcom_pcie *pcie);
 	void (*deinit)(struct qcom_pcie *pcie);
+	void (*ltssm_enable)(struct qcom_pcie *pcie);
 };
 
 struct qcom_pcie {
@@ -116,17 +133,33 @@  static irqreturn_t qcom_pcie_msi_irq_handler(int irq, void *arg)
 	return dw_handle_msi_irq(pp);
 }
 
-static int qcom_pcie_establish_link(struct qcom_pcie *pcie)
+static void qcom_pcie_v0_v1_ltssm_enable(struct qcom_pcie *pcie)
 {
 	u32 val;
-
-	if (dw_pcie_link_up(&pcie->pp))
-		return 0;
-
 	/* enable link training */
 	val = readl(pcie->elbi + PCIE20_ELBI_SYS_CTRL);
 	val |= PCIE20_ELBI_SYS_CTRL_LT_ENABLE;
 	writel(val, pcie->elbi + PCIE20_ELBI_SYS_CTRL);
+}
+
+static void qcom_pcie_v2_ltssm_enable(struct qcom_pcie *pcie)
+{
+	u32 val;
+	/* enable link training */
+	val = readl(pcie->parf + PCIE20_PARF_LTSSM);
+	val |= BIT(8);
+	writel(val, pcie->parf + PCIE20_PARF_LTSSM);
+}
+
+static int qcom_pcie_establish_link(struct qcom_pcie *pcie)
+{
+
+	if (dw_pcie_link_up(&pcie->pp))
+		return 0;
+
+	/* Enable Link Training state machine */
+	if (pcie->ops->ltssm_enable)
+		pcie->ops->ltssm_enable(pcie);
 
 	return dw_pcie_wait_for_link(&pcie->pp);
 }
@@ -421,6 +454,113 @@  static int qcom_pcie_init_v1(struct qcom_pcie *pcie)
 	return ret;
 }
 
+static int qcom_pcie_get_resources_v2(struct qcom_pcie *pcie)
+{
+	struct qcom_pcie_resources_v2 *res = &pcie->res.v2;
+	struct device *dev = pcie->pp.dev;
+
+	res->aux_clk = devm_clk_get(dev, "aux");
+	if (IS_ERR(res->aux_clk))
+		return PTR_ERR(res->aux_clk);
+
+	res->cfg_clk = devm_clk_get(dev, "cfg");
+	if (IS_ERR(res->cfg_clk))
+		return PTR_ERR(res->cfg_clk);
+
+	res->master_clk = devm_clk_get(dev, "bus_master");
+	if (IS_ERR(res->master_clk))
+		return PTR_ERR(res->master_clk);
+
+	res->slave_clk = devm_clk_get(dev, "bus_slave");
+	if (IS_ERR(res->slave_clk))
+		return PTR_ERR(res->slave_clk);
+
+	res->pipe_clk = devm_clk_get(dev, "pipe");
+	if (IS_ERR(res->pipe_clk))
+		return PTR_ERR(res->pipe_clk);
+
+	return 0;
+}
+
+static int qcom_pcie_init_v2(struct qcom_pcie *pcie)
+{
+	struct qcom_pcie_resources_v2 *res = &pcie->res.v2;
+	struct device *dev = pcie->pp.dev;
+	u32 val;
+	int ret;
+
+	ret = clk_prepare_enable(res->aux_clk);
+	if (ret) {
+		dev_err(dev, "cannot prepare/enable aux clock\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(res->cfg_clk);
+	if (ret) {
+		dev_err(dev, "cannot prepare/enable cfg clock\n");
+		goto err_cfg_clk;
+	}
+
+	ret = clk_prepare_enable(res->master_clk);
+	if (ret) {
+		dev_err(dev, "cannot prepare/enable master clock\n");
+		goto err_master_clk;
+	}
+
+	ret = clk_prepare_enable(res->slave_clk);
+	if (ret) {
+		dev_err(dev, "cannot prepare/enable slave clock\n");
+		goto err_slave_clk;
+	}
+
+	/* enable PCIe clocks and resets */
+	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
+	val &= ~BIT(0);
+	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
+
+	/* change DBI base address */
+	writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
+
+	/* MAC PHY_POWERDOWN MUX DISABLE  */
+	val = readl(pcie->parf + PCIE20_PARF_SYS_CTRL);
+	val &= ~BIT(29);
+	writel(val, pcie->parf + PCIE20_PARF_SYS_CTRL);
+
+	val = readl(pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
+	val |= BIT(4);
+	writel(val, pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
+
+	val = readl(pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2);
+	val |= BIT(31);
+	writel(val, pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2);
+
+	return 0;
+
+err_slave_clk:
+	clk_disable_unprepare(res->master_clk);
+err_master_clk:
+	clk_disable_unprepare(res->cfg_clk);
+err_cfg_clk:
+	clk_disable_unprepare(res->aux_clk);
+
+	return ret;
+}
+
+static int qcom_pcie_post_init_v2(struct qcom_pcie *pcie)
+{
+	struct qcom_pcie_resources_v2 *res = &pcie->res.v2;
+	struct device *dev = pcie->pp.dev;
+	int ret;
+
+	ret = clk_prepare_enable(res->pipe_clk);
+	if (ret) {
+		dev_err(dev, "cannot prepare/enable pipe clock\n");
+		return ret;
+	}
+
+	return 0;
+}
+
 static int qcom_pcie_link_up(struct pcie_port *pp)
 {
 	struct qcom_pcie *pcie = to_qcom_pcie(pp);
@@ -429,6 +569,17 @@  static int qcom_pcie_link_up(struct pcie_port *pp)
 	return !!(val & PCI_EXP_LNKSTA_DLLLA);
 }
 
+static void qcom_pcie_deinit_v2(struct qcom_pcie *pcie)
+{
+	struct qcom_pcie_resources_v2 *res = &pcie->res.v2;
+
+	clk_disable_unprepare(res->pipe_clk);
+	clk_disable_unprepare(res->slave_clk);
+	clk_disable_unprepare(res->master_clk);
+	clk_disable_unprepare(res->cfg_clk);
+	clk_disable_unprepare(res->aux_clk);
+}
+
 static void qcom_pcie_host_init(struct pcie_port *pp)
 {
 	struct qcom_pcie *pcie = to_qcom_pcie(pp);
@@ -444,6 +595,9 @@  static void qcom_pcie_host_init(struct pcie_port *pp)
 	if (ret)
 		goto err_deinit;
 
+	if (pcie->ops->post_init)
+		pcie->ops->post_init(pcie);
+
 	dw_pcie_setup_rc(pp);
 
 	if (IS_ENABLED(CONFIG_PCI_MSI))
@@ -487,12 +641,22 @@  static const struct qcom_pcie_ops ops_v0 = {
 	.get_resources = qcom_pcie_get_resources_v0,
 	.init = qcom_pcie_init_v0,
 	.deinit = qcom_pcie_deinit_v0,
+	.ltssm_enable = qcom_pcie_v0_v1_ltssm_enable,
 };
 
 static const struct qcom_pcie_ops ops_v1 = {
 	.get_resources = qcom_pcie_get_resources_v1,
 	.init = qcom_pcie_init_v1,
 	.deinit = qcom_pcie_deinit_v1,
+	.ltssm_enable = qcom_pcie_v0_v1_ltssm_enable,
+};
+
+static const struct qcom_pcie_ops ops_v2 = {
+	.get_resources = qcom_pcie_get_resources_v2,
+	.init = qcom_pcie_init_v2,
+	.post_init = qcom_pcie_post_init_v2,
+	.deinit = qcom_pcie_deinit_v2,
+	.ltssm_enable = qcom_pcie_v2_ltssm_enable,
 };
 
 static int qcom_pcie_probe(struct platform_device *pdev)
@@ -572,6 +736,7 @@  static const struct of_device_id qcom_pcie_match[] = {
 	{ .compatible = "qcom,pcie-ipq8064", .data = &ops_v0 },
 	{ .compatible = "qcom,pcie-apq8064", .data = &ops_v0 },
 	{ .compatible = "qcom,pcie-apq8084", .data = &ops_v1 },
+	{ .compatible = "qcom,pcie-msm8996", .data = &ops_v2 },
 	{ }
 };