diff mbox series

[3/7] board: ti: am571x-idk: Support 6 port Ethernet or 4 port Ethernet with LCD

Message ID 1485436049-19754-4-git-send-email-rogerq@ti.com
State Superseded
Headers show
Series am57xx-idk LCD and am571x-idk 6 port ethernet pinmux | expand

Commit Message

Roger Quadros Jan. 26, 2017, 1:07 p.m. UTC 
The board can support either ICSS1 Ethernet ports or LCD
based on J51 jumper. Factory default is ICSS1 Ethernet ports
(i.e. Jumper not populated).

Use the GPIO to detect the jumper setting and configure the
pinmux accordingly. Also select the right DT blob based on
the chosen configuration.

J51 absent -> ICSS1 Ethernet, no LCD on VOUT -> am571x-idk.dtb
J51 present -> LCD on VOUT, no ICSS1 Ethernet -> am571x-idk-lcd-osd.dtb

At present we only support the assume it is the Legacy LCD.
LCD detection mechanism needs to be added later to differentiate
between legacy vs new LCD.

For ICSS1 Ethernet pins use the following convention to set the pinmux
as PMT data is not yet finalized.

- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
- Do not use SLEW_CONTROLon any pin.

[nm@ti.com] Fix wrong dtb selection caused by a typo ';'

Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>

---
 board/ti/am57xx/board.c           |  40 +++++++++++++++
 board/ti/am57xx/mux_data.h        | 104 +++++++++++++++++++++++++-------------
 include/configs/ti_omap5_common.h |   4 +-
 3 files changed, 112 insertions(+), 36 deletions(-)

-- 
2.7.4

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Comments

Tom Rini Jan. 26, 2017, 5:41 p.m. UTC | #1 
On Thu, Jan 26, 2017 at 03:07:25PM +0200, Roger Quadros wrote:

> The board can support either ICSS1 Ethernet ports or LCD

> based on J51 jumper. Factory default is ICSS1 Ethernet ports

> (i.e. Jumper not populated).

> 

> Use the GPIO to detect the jumper setting and configure the

> pinmux accordingly. Also select the right DT blob based on

> the chosen configuration.

> 

> J51 absent -> ICSS1 Ethernet, no LCD on VOUT -> am571x-idk.dtb

> J51 present -> LCD on VOUT, no ICSS1 Ethernet -> am571x-idk-lcd-osd.dtb

> 

> At present we only support the assume it is the Legacy LCD.

> LCD detection mechanism needs to be added later to differentiate

> between legacy vs new LCD.

> 

> For ICSS1 Ethernet pins use the following convention to set the pinmux

> as PMT data is not yet finalized.

> 

> - If pin is output, set as PIN_OUTPUT

> - If pin is input and external pull resistor present set as PIN_INPUT

> - If pin is input and external pull resistor absent, set pull to same

> as that of the external PHY's internall pull.

> - Do not use SLEW_CONTROLon any pin.

> 

> [nm@ti.com] Fix wrong dtb selection caused by a typo ';'

> 

> Cc: Nishanth Menon <nm@ti.com>

> Signed-off-by: Roger Quadros <rogerq@ti.com>


Reviewed-by: Tom Rini <trini@konsulko.com>


-- 
Tom
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
diff mbox series

Patch

diff --git a/board/ti/am57xx/board.c b/board/ti/am57xx/board.c
index 5f2d4df..81ad86c 100644
--- a/board/ti/am57xx/board.c
+++ b/board/ti/am57xx/board.c
@@ -50,6 +50,7 @@ 
 
 DECLARE_GLOBAL_DATA_PTR;
 
+#define GPIO_ETH_LCD		GPIO_TO_PIN(2, 22)
 /* GPIO 7_11 */
 #define GPIO_DDR_VTT_EN 203
 
@@ -449,6 +450,21 @@  void hw_data_init(void)
 	*ctrl = &dra7xx_ctrl;
 }
 
+bool am571x_idk_needs_lcd(void)
+{
+	bool needs_lcd;
+
+	gpio_request(GPIO_ETH_LCD, "nLCD_Detect");
+	if (gpio_get_value(GPIO_ETH_LCD))
+		needs_lcd = false;
+	else
+		needs_lcd = true;
+
+	gpio_free(GPIO_ETH_LCD);
+
+	return needs_lcd;
+}
+
 int board_init(void)
 {
 	gpmc_init();
@@ -459,6 +475,8 @@  int board_init(void)
 
 int board_late_init(void)
 {
+	char *idk_lcd;
+
 	setup_board_eeprom_env();
 	u8 val;
 
@@ -487,6 +505,17 @@  int board_late_init(void)
 	palmas_i2c_write_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2,
 			    val);
 
+	/* TBD: Add LCD panel detection once information is available */
+	if (am571x_idk_needs_lcd())
+		idk_lcd = "osd101t2045"; /* Default to legacy LCD */
+	else
+		idk_lcd = "no";
+	setenv("idk_lcd", idk_lcd);
+
+#if !defined(CONFIG_SPL_BUILD)
+	board_ti_set_ethaddr(2);
+#endif
+
 	return 0;
 }
 
@@ -549,6 +578,17 @@  void recalibrate_iodelay(void)
 		do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz);
 	}
 
+	if (board_is_am571x_idk()) {
+		if (am571x_idk_needs_lcd()) {
+			pconf = core_padconf_array_vout_am571x_idk;
+			pconf_sz = ARRAY_SIZE(core_padconf_array_vout_am571x_idk);
+		} else {
+			pconf = core_padconf_array_icss1eth_am571x_idk;
+			pconf_sz = ARRAY_SIZE(core_padconf_array_icss1eth_am571x_idk);
+		}
+		do_set_mux32((*ctrl)->control_padconf_core_base, pconf, pconf_sz);
+	}
+
 	/* Setup IOdelay configuration */
 	ret = do_set_iodelay((*ctrl)->iodelay_config_base, iod, iod_sz);
 err:
diff --git a/board/ti/am57xx/mux_data.h b/board/ti/am57xx/mux_data.h
index 2f5243e..ff0e517 100644
--- a/board/ti/am57xx/mux_data.h
+++ b/board/ti/am57xx/mux_data.h
@@ -549,13 +549,6 @@  const struct pad_conf_entry core_padconf_array_essential_am571x_idk[] = {
 	{VIN2A_D0, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d0.pr1_uart0_rxd */
 	{VIN2A_D1, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d1.pr1_uart0_txd */
 	{VIN2A_D2, (M10 | PIN_INPUT_PULLDOWN)},	/* vin2a_d2.eCAP1_in_PWM1_out */
-	{VIN2A_D3, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d3.pr1_mi1_col */
-	{VIN2A_D4, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d4.pr1_mii1_txd1 */
-	{VIN2A_D5, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d5.pr1_mii1_txd0 */
-	{VIN2A_D6, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d6.pr1_mii_mt1_clk */
-	{VIN2A_D7, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d7.pr1_mii1_txen */
-	{VIN2A_D8, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d8.pr1_mii1_txd3 */
-	{VIN2A_D9, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d9.pr1_mii1_txd2 */
 	{VIN2A_D10, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d10.pr1_mdio_mdclk */
 	{VIN2A_D11, (M11 | PIN_INPUT_PULLUP)},	/* vin2a_d11.pr1_mdio_data */
 	{VIN2A_D12, (M3 | PIN_INPUT_PULLDOWN | MANUAL_MODE)},	/* vin2a_d12.rgmii1_txc */
@@ -570,35 +563,7 @@  const struct pad_conf_entry core_padconf_array_essential_am571x_idk[] = {
 	{VIN2A_D21, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* vin2a_d21.rgmii1_rxd2 */
 	{VIN2A_D22, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* vin2a_d22.rgmii1_rxd1 */
 	{VIN2A_D23, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)},	/* vin2a_d23.rgmii1_rxd0 */
-	{VOUT1_CLK, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_clk.vout1_clk */
-	{VOUT1_DE, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_de.vout1_de */
 	{VOUT1_FLD, (M14 | PIN_INPUT_PULLUP)},	/* vout1_fld.gpio4_21 */
-	{VOUT1_HSYNC, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_hsync.vout1_hsync */
-	{VOUT1_VSYNC, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_vsync.vout1_vsync */
-	{VOUT1_D0, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d0.vout1_d0 */
-	{VOUT1_D1, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d1.vout1_d1 */
-	{VOUT1_D2, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d2.vout1_d2 */
-	{VOUT1_D3, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d3.vout1_d3 */
-	{VOUT1_D4, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d4.vout1_d4 */
-	{VOUT1_D5, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d5.vout1_d5 */
-	{VOUT1_D6, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d6.vout1_d6 */
-	{VOUT1_D7, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d7.vout1_d7 */
-	{VOUT1_D8, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d8.vout1_d8 */
-	{VOUT1_D9, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d9.vout1_d9 */
-	{VOUT1_D10, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d10.vout1_d10 */
-	{VOUT1_D11, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d11.vout1_d11 */
-	{VOUT1_D12, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d12.vout1_d12 */
-	{VOUT1_D13, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d13.vout1_d13 */
-	{VOUT1_D14, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d14.vout1_d14 */
-	{VOUT1_D15, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d15.vout1_d15 */
-	{VOUT1_D16, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d16.vout1_d16 */
-	{VOUT1_D17, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d17.vout1_d17 */
-	{VOUT1_D18, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d18.vout1_d18 */
-	{VOUT1_D19, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d19.vout1_d19 */
-	{VOUT1_D20, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d20.vout1_d20 */
-	{VOUT1_D21, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d21.vout1_d21 */
-	{VOUT1_D22, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d22.vout1_d22 */
-	{VOUT1_D23, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d23.vout1_d23 */
 	{MDIO_MCLK, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)},	/* mdio_mclk.mdio_mclk */
 	{MDIO_D, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)},	/* mdio_d.mdio_d */
 	{RMII_MHZ_50_CLK, (M13 | PIN_INPUT_PULLDOWN)},	/* RMII_MHZ_50_CLK.pr2_pru1_gpo2 */
@@ -727,6 +692,75 @@  const struct pad_conf_entry core_padconf_array_essential_am571x_idk[] = {
 	{RSTOUTN, (M0 | PIN_OUTPUT_PULLDOWN)},	/* rstoutn.rstoutn */
 };
 
+const struct pad_conf_entry core_padconf_array_icss1eth_am571x_idk[] = {
+	/* PR1 MII0 */
+	{VOUT1_D8, (M12 | PIN_INPUT_PULLDOWN)},	/* vout1_d8.pr1_mii_mt0_clk */
+	{VOUT1_D9, (M13 | PIN_OUTPUT)},		/* vout1_d9.pr1_mii0_txd3 */
+	{VOUT1_D10, (M13 | PIN_OUTPUT)},	/* vout1_d10.pr1_mii0_txd2 */
+	{VOUT1_D11, (M13 | PIN_OUTPUT)},	/* vout1_d11.pr1_mii0_txen */
+	{VOUT1_D12, (M13 | PIN_OUTPUT)},	/* vout1_d12.pr1_mii0_txd1 */
+	{VOUT1_D13, (M13 | PIN_OUTPUT)},	/* vout1_d13.pr1_mii0_txd0 */
+	{VOUT1_D14, (M12 | PIN_INPUT_PULLDOWN)},	/* vout1_d14.pr1_mii_mr0_clk */
+	{VOUT1_D15, (M12 | PIN_INPUT_PULLDOWN)},	/* vout1_d15.pr1_mii0_rxdv */
+	{VOUT1_D16, (M12 | PIN_INPUT)},	/* vout1_d16.pr1_mii0_rxd3 */
+	{VOUT1_D17, (M12 | PIN_INPUT)},	/* vout1_d17.pr1_mii0_rxd2 */
+	{VOUT1_D18, (M12 | PIN_INPUT)},	/* vout1_d18.pr1_mii0_rxd1 */
+	{VOUT1_D19, (M12 | PIN_INPUT)},	/* vout1_d19.pr1_mii0_rxd0 */
+	{VOUT1_D20, (M12 | PIN_INPUT_PULLUP)},	/* vout1_d20.pr1_mii0_rxer */
+	{VOUT1_D21, (M12 | PIN_INPUT)},	/* vout1_d21.pr1_mii0_rxlink */
+	{VOUT1_D22, (M12 | PIN_INPUT)},	/* vout1_d22.pr1_mii0_col */
+	{VOUT1_D23, (M12 | PIN_INPUT_PULLUP)},	/* vout1_d23.pr1_mii0_crs */
+
+	/* PR1 MII1 */
+	{VIN2A_D3, (M12 | PIN_INPUT)},	/* vin2a_d3.pr1_mi1_col */
+	{VIN2A_D4, (M13 | PIN_OUTPUT)},	/* vin2a_d4.pr1_mii1_txd1 */
+	{VIN2A_D5, (M13 | PIN_OUTPUT)},	/* vin2a_d5.pr1_mii1_txd0 */
+	{VIN2A_D6, (M11 | PIN_INPUT_PULLDOWN)},	/* vin2a_d6.pr1_mii_mt1_clk */
+	{VIN2A_D7, (M11 | PIN_OUTPUT)},	/* vin2a_d7.pr1_mii1_txen */
+	{VIN2A_D8, (M11 | PIN_OUTPUT)},	/* vin2a_d8.pr1_mii1_txd3 */
+	{VIN2A_D9, (M11 | PIN_OUTPUT)},	/* vin2a_d9.pr1_mii1_txd2 */
+	{VOUT1_VSYNC, (M12 | PIN_INPUT_PULLUP)},	/* vout1_vsync.pr1_mii1_rxer */
+	{VOUT1_D0, (M12 | PIN_INPUT)},	/* vout1_d0.pr1_mii1_rxlink */
+	{VOUT1_D1, (M12 | PIN_INPUT_PULLUP)},	/* vout1_d1.pr1_mii1_crs */
+	{VOUT1_D2, (M12 | PIN_INPUT_PULLDOWN)},	/* vout1_d2.pr1_mii_mr1_clk */
+	{VOUT1_D3, (M12 | PIN_INPUT_PULLDOWN)},	/* vout1_d3.pr1_mii1_rxdv */
+	{VOUT1_D4, (M12 | PIN_INPUT)},	/* vout1_d4.pr1_mii1_rxd3 */
+	{VOUT1_D5, (M12 | PIN_INPUT)},	/* vout1_d5.pr1_mii1_rxd2 */
+	{VOUT1_D6, (M12 | PIN_INPUT)},	/* vout1_d6.pr1_mii1_rxd1 */
+	{VOUT1_D7, (M12 | PIN_INPUT)},	/* vout1_d7.pr1_mii1_rxd0 */
+};
+
+const struct pad_conf_entry core_padconf_array_vout_am571x_idk[] = {
+	{VOUT1_CLK, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_clk.vout1_clk */
+	{VOUT1_DE, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_de.vout1_de */
+	{VOUT1_HSYNC, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_hsync.vout1_hsync */
+	{VOUT1_VSYNC, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_vsync.vout1_vsync */
+	{VOUT1_D0, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d0.vout1_d0 */
+	{VOUT1_D1, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d1.vout1_d1 */
+	{VOUT1_D2, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d2.vout1_d2 */
+	{VOUT1_D3, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d3.vout1_d3 */
+	{VOUT1_D4, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d4.vout1_d4 */
+	{VOUT1_D5, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d5.vout1_d5 */
+	{VOUT1_D6, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d6.vout1_d6 */
+	{VOUT1_D7, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d7.vout1_d7 */
+	{VOUT1_D8, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d8.vout1_d8 */
+	{VOUT1_D9, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d9.vout1_d9 */
+	{VOUT1_D10, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d10.vout1_d10 */
+	{VOUT1_D11, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d11.vout1_d11 */
+	{VOUT1_D12, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d12.vout1_d12 */
+	{VOUT1_D13, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d13.vout1_d13 */
+	{VOUT1_D14, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d14.vout1_d14 */
+	{VOUT1_D15, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d15.vout1_d15 */
+	{VOUT1_D16, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d16.vout1_d16 */
+	{VOUT1_D17, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d17.vout1_d17 */
+	{VOUT1_D18, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d18.vout1_d18 */
+	{VOUT1_D19, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d19.vout1_d19 */
+	{VOUT1_D20, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d20.vout1_d20 */
+	{VOUT1_D21, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d21.vout1_d21 */
+	{VOUT1_D22, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d22.vout1_d22 */
+	{VOUT1_D23, (M0 | PIN_INPUT_PULLDOWN)},	/* vout1_d23.vout1_d23 */
+};
+
 const struct pad_conf_entry early_padconf[] = {
 	{UART2_CTSN, (M2 | PIN_INPUT_SLEW)},	/* uart2_ctsn.uart3_rxd */
 	{UART2_RTSN, (M1 | PIN_INPUT_SLEW)},	/* uart2_rtsn.uart3_txd */
diff --git a/include/configs/ti_omap5_common.h b/include/configs/ti_omap5_common.h
index 37d6565..6de19c2 100644
--- a/include/configs/ti_omap5_common.h
+++ b/include/configs/ti_omap5_common.h
@@ -97,8 +97,10 @@ 
 			"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
 		"if test $board_name = am57xx_evm_reva3; then " \
 			"setenv fdtfile am57xx-beagle-x15.dtb; fi;" \
-		"if test $board_name = am571x_idk; then " \
+		"if test $board_name = am571x_idk && test $idk_lcd = no; then " \
 			"setenv fdtfile am571x-idk.dtb; fi;" \
+		"if test $board_name = am571x_idk && test $idk_lcd = osd101t2045; then " \
+			"setenv fdtfile am571x-idk-lcd-osd.dtb; fi;" \
 		"if test $fdtfile = undefined; then " \
 			"echo WARNING: Could not determine device tree to use; fi; \0" \
 	DFUARGS \