| Message ID | 1486185234-23675-7-git-send-email-haojian.zhuang@linaro.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | enable Android Fastboot App on HiKey | expand |
On 02/03/2017 11:13 PM, Haojian Zhuang wrote: > Support Designware USB device controller on HiKey platform. Hi, Are there plans to support this controller as a USB host rather than just a fastboot device? Thanks, > > Contributed-under: TianoCore Contribution Agreement 1.0 > Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> > --- > .../Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.c | 266 +++++++++++++++++++++ > .../Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.inf | 46 ++++ > 2 files changed, 312 insertions(+) > create mode 100644 Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.c > create mode 100644 Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.inf > > diff --git a/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.c b/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.c > new file mode 100644 > index 0000000..60ad4d6 > --- /dev/null > +++ b/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.c > @@ -0,0 +1,266 @@ > +/** @file > +* > +* Copyright (c) 2015-2017, Linaro. All rights reserved. > +* > +* This program and the accompanying materials > +* are licensed and made available under the terms and conditions of the BSD License > +* which accompanies this distribution. The full text of the license may be found at > +* http://opensource.org/licenses/bsd-license.php > +* > +* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, > +* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. > +* > +**/ > + > +#include <Library/BaseMemoryLib.h> > +#include <Library/DebugLib.h> > +#include <Library/IoLib.h> > +#include <Library/TimerLib.h> > +#include <Library/UefiBootServicesTableLib.h> > +#include <Library/UefiLib.h> > +#include <Library/UefiRuntimeServicesTableLib.h> > + > +#include <Protocol/EmbeddedGpio.h> > +#include <Protocol/DwUsb.h> > + > +#include <Hi6220.h> > + > + > +#define USB_SEL_GPIO0_3 3 // GPIO 0_3 > +#define USB_5V_HUB_EN 7 // GPIO 0_7 > +#define USB_ID_DET_GPIO2_5 21 // GPIO 2_5 > +#define USB_VBUS_DET_GPIO2_6 22 // GPIO 2_6 > + > +// Jumper on pin5-6 of J15 determines whether boot to fastboot > +#define DETECT_J15_FASTBOOT 24 // GPIO 3_0 > + > +STATIC EMBEDDED_GPIO *mGpio; > + > +STATIC > +VOID > +HiKeyDetectUsbModeInit ( > + IN VOID > + ) > +{ > + EFI_STATUS Status; > + > + /* set pullup on both GPIO2_5 & GPIO2_6. It's required for inupt. */ > + MmioWrite32 (0xf8001864, 1); > + MmioWrite32 (0xf8001868, 1); > + > + Status = gBS->LocateProtocol (&gEmbeddedGpioProtocolGuid, NULL, (VOID **)&mGpio); > + ASSERT_EFI_ERROR (Status); > + Status = mGpio->Set (mGpio, USB_SEL_GPIO0_3, GPIO_MODE_OUTPUT_0); > + ASSERT_EFI_ERROR (Status); > + Status = mGpio->Set (mGpio, USB_5V_HUB_EN, GPIO_MODE_OUTPUT_0); > + ASSERT_EFI_ERROR (Status); > + MicroSecondDelay (1000); > + > + Status = mGpio->Set (mGpio, USB_ID_DET_GPIO2_5, GPIO_MODE_INPUT); > + ASSERT_EFI_ERROR (Status); > + Status = mGpio->Set (mGpio, USB_VBUS_DET_GPIO2_6, GPIO_MODE_INPUT); > + ASSERT_EFI_ERROR (Status); > +} > + > +UINTN > +HiKeyGetUsbMode ( > + IN VOID > + ) > +{ > +#if 0 > + EFI_STATUS Status; > + UINTN GpioId, GpioVbus; > + UINTN Value; > + > + Status = mGpio->Get (mGpio, USB_ID_DET_GPIO2_5, &Value); > + ASSERT_EFI_ERROR (Status); > + GpioId = Value; > + Status = mGpio->Get (mGpio, USB_VBUS_DET_GPIO2_6, &Value); > + ASSERT_EFI_ERROR (Status); > + GpioVbus = Value; > + > +DEBUG ((DEBUG_ERROR, "#%a, %d, GpioId:%d, GpioVbus:%d\n", __func__, __LINE__, GpioId, GpioVbus)); > + if ((GpioId == 1) && (GpioVbus == 0)) { > + return USB_DEVICE_MODE; > + } else if ((GpioId == 0) && (GpioVbus == 1)) { > + return USB_CABLE_NOT_ATTACHED; > + } > + return USB_HOST_MODE; > +#else > + return USB_DEVICE_MODE; > +#endif > +} > + > +EFI_STATUS > +HiKeyUsbPhyInit ( > + IN UINT8 Mode > + ) > +{ > + UINTN Value; > + UINT32 Data; > + > + HiKeyDetectUsbModeInit (); > + > + //setup clock > + MmioWrite32 (PERI_CTRL_BASE + SC_PERIPH_CLKEN0, BIT4); > + do { > + Value = MmioRead32 (PERI_CTRL_BASE + SC_PERIPH_CLKSTAT0); > + } while ((Value & BIT4) == 0); > + > + //setup phy > + Data = RST0_USBOTG_BUS | RST0_POR_PICOPHY | > + RST0_USBOTG | RST0_USBOTG_32K; > + MmioWrite32 (PERI_CTRL_BASE + SC_PERIPH_RSTDIS0, Data); > + do { > + Value = MmioRead32 (PERI_CTRL_BASE + SC_PERIPH_RSTSTAT0); > + Value &= Data; > + } while (Value); > + > + Value = MmioRead32 (PERI_CTRL_BASE + SC_PERIPH_CTRL4); > + Value &= ~(CTRL4_PICO_SIDDQ | CTRL4_FPGA_EXT_PHY_SEL | > + CTRL4_OTG_PHY_SEL); > + Value |= CTRL4_PICO_VBUSVLDEXT | CTRL4_PICO_VBUSVLDEXTSEL; > + MmioWrite32 (PERI_CTRL_BASE + SC_PERIPH_CTRL4, Value); > + MicroSecondDelay (1000); > + > + //If Mode = 1, USB in Device Mode > + //If Mode = 0, USB in Host Mode > + if (Mode == USB_DEVICE_MODE) { > + if (HiKeyGetUsbMode () == USB_DEVICE_MODE) { > + DEBUG ((DEBUG_ERROR, "usb work as device mode.\n")); > + } else { > + return EFI_INVALID_PARAMETER; > + } > + > + Value = MmioRead32 (PERI_CTRL_BASE + SC_PERIPH_CTRL5); > + Value &= ~CTRL5_PICOPHY_BC_MODE; > + MmioWrite32 (PERI_CTRL_BASE + SC_PERIPH_CTRL5, Value); > + MicroSecondDelay (20000); > + } else { > + if (HiKeyGetUsbMode () == USB_HOST_MODE) { > + DEBUG ((DEBUG_ERROR, "usb work as host mode.\n")); > + } else { > + return EFI_INVALID_PARAMETER; > + } > + > + /*CTRL5*/ > + Data = MmioRead32 (PERI_CTRL_BASE + SC_PERIPH_CTRL5); > + Data &= ~CTRL5_PICOPHY_BC_MODE; > + Data |= CTRL5_USBOTG_RES_SEL | CTRL5_PICOPHY_ACAENB | > + CTRL5_PICOPHY_VDATDETENB | CTRL5_PICOPHY_DCDENB; > + MmioWrite32 (PERI_CTRL_BASE + SC_PERIPH_CTRL5, Data); > + MicroSecondDelay (20000); > + MmioWrite32 (PERI_CTRL_BASE + 0x018, 0x70533483); //EYE_PATTERN > + > + MicroSecondDelay (5000); > + } > + > + return EFI_SUCCESS; > +} > + > +EFI_STATUS > +EFIAPI > +HiKeyUsbGetLang ( > + OUT CHAR16 *Lang, > + OUT UINT8 *Length > + ) > +{ > + if ((Lang == NULL) || (Length == NULL)) { > + return EFI_INVALID_PARAMETER; > + } > + Lang[0] = 0x409; > + *Length = sizeof (CHAR16); > + return EFI_SUCCESS; > +} > + > +EFI_STATUS > +EFIAPI > +HiKeyUsbGetManuFacturer ( > + OUT CHAR16 *ManuFacturer, > + OUT UINT8 *Length > + ) > +{ > + UINTN VariableSize; > + CHAR16 DataUnicode[MANU_FACTURER_STRING_LENGTH]; > + > + if ((ManuFacturer == NULL) || (Length == NULL)) { > + return EFI_INVALID_PARAMETER; > + } > + VariableSize = MANU_FACTURER_STRING_LENGTH * sizeof (CHAR16); > + ZeroMem (DataUnicode, MANU_FACTURER_STRING_LENGTH * sizeof(CHAR16)); > + StrCpy (DataUnicode, L"96Boards"); > + CopyMem (ManuFacturer, DataUnicode, VariableSize); > + *Length = VariableSize; > + return EFI_SUCCESS; > +} > + > +EFI_STATUS > +EFIAPI > +HiKeyUsbGetProduct ( > + OUT CHAR16 *Product, > + OUT UINT8 *Length > + ) > +{ > + UINTN VariableSize; > + CHAR16 DataUnicode[PRODUCT_STRING_LENGTH]; > + > + if ((Product == NULL) || (Length == NULL)) { > + return EFI_INVALID_PARAMETER; > + } > + VariableSize = PRODUCT_STRING_LENGTH * sizeof (CHAR16); > + ZeroMem (DataUnicode, PRODUCT_STRING_LENGTH * sizeof(CHAR16)); > + StrCpy (DataUnicode, L"HiKey"); > + CopyMem (Product, DataUnicode, VariableSize); > + *Length = VariableSize; > + return EFI_SUCCESS; > +} > + > +EFI_STATUS > +EFIAPI > +HiKeyUsbGetSerialNo ( > + OUT CHAR16 *SerialNo, > + OUT UINT8 *Length > + ) > +{ > + UINTN VariableSize; > + CHAR16 DataUnicode[SERIAL_STRING_LENGTH]; > + > + if ((SerialNo == NULL) || (Length == NULL)) { > + return EFI_INVALID_PARAMETER; > + } > + VariableSize = SERIAL_STRING_LENGTH * sizeof (CHAR16); > + ZeroMem (DataUnicode, SERIAL_STRING_LENGTH * sizeof(CHAR16)); > + StrCpy (DataUnicode, L"0123456789abcdef"); > + CopyMem (SerialNo, DataUnicode, VariableSize); > + *Length = VariableSize; > + return EFI_SUCCESS; > +} > + > +DW_USB_PROTOCOL mDwUsbDevice = { > + HiKeyUsbGetLang, > + HiKeyUsbGetManuFacturer, > + HiKeyUsbGetProduct, > + HiKeyUsbGetSerialNo, > + HiKeyUsbPhyInit > +}; > + > +EFI_STATUS > +EFIAPI > +HiKeyUsbEntryPoint ( > + IN EFI_HANDLE ImageHandle, > + IN EFI_SYSTEM_TABLE *SystemTable > + ) > +{ > + EFI_STATUS Status; > + > + Status = gBS->InstallProtocolInterface ( > + &ImageHandle, > + &gDwUsbProtocolGuid, > + EFI_NATIVE_INTERFACE, > + &mDwUsbDevice > + ); > + if (EFI_ERROR (Status)) { > + return Status; > + } > + return Status; > +} > diff --git a/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.inf b/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.inf > new file mode 100644 > index 0000000..75ff599 > --- /dev/null > +++ b/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.inf > @@ -0,0 +1,46 @@ > +#/** @file > +# > +# Copyright (c) 2015-2017, Linaro. All rights reserved. > +# > +# This program and the accompanying materials > +# are licensed and made available under the terms and conditions of the BSD License > +# which accompanies this distribution. The full text of the license may be found at > +# http://opensource.org/licenses/bsd-license.php > +# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, > +# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. > +# > +# > +#**/ > + > +[Defines] > + INF_VERSION = 0x00010019 > + BASE_NAME = HiKeyUsbDxe > + FILE_GUID = c5c7089e-9b00-448c-8b23-a552688e2833 > + MODULE_TYPE = UEFI_DRIVER > + VERSION_STRING = 1.0 > + ENTRY_POINT = HiKeyUsbEntryPoint > + > +[Sources.common] > + HiKeyUsbDxe.c > + > +[LibraryClasses] > + DebugLib > + IoLib > + TimerLib > + UefiBootServicesTableLib > + UefiDriverEntryPoint > + > +[Protocols] > + gDwUsbProtocolGuid > + gEfiDriverBindingProtocolGuid > + gEmbeddedGpioProtocolGuid > + > +[Packages] > + MdePkg/MdePkg.dec > + MdeModulePkg/MdeModulePkg.dec > + EmbeddedPkg/EmbeddedPkg.dec > + OpenPlatformPkg/Drivers/Usb/DwUsbDxe/DwUsbDxe.dec > + OpenPlatformPkg/Platforms/Hisilicon/HiKey/HiKey.dec > + > +[Depex] > + BEFORE gDwUsbDeviceGuid >
On 6 February 2017 at 17:43, Jeremy Linton <jeremy.linton@arm.com> wrote: > On 02/03/2017 11:13 PM, Haojian Zhuang wrote: >> >> Support Designware USB device controller on HiKey platform. > > > Hi, > > Are there plans to support this controller as a USB host rather than just a > fastboot device? > There is a separate host mode driver for it, which they disabled on HiKey (I think) because it broke something else, presumably fastboot. It is the same IP as Raspberry Pi 3, and I spent some time porting that a couple of months ago (without any result so far)
diff --git a/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.c b/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.c new file mode 100644 index 0000000..60ad4d6 --- /dev/null +++ b/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.c @@ -0,0 +1,266 @@ +/** @file +* +* Copyright (c) 2015-2017, Linaro. All rights reserved. +* +* This program and the accompanying materials +* are licensed and made available under the terms and conditions of the BSD License +* which accompanies this distribution. The full text of the license may be found at +* http://opensource.org/licenses/bsd-license.php +* +* THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, +* WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. +* +**/ + +#include <Library/BaseMemoryLib.h> +#include <Library/DebugLib.h> +#include <Library/IoLib.h> +#include <Library/TimerLib.h> +#include <Library/UefiBootServicesTableLib.h> +#include <Library/UefiLib.h> +#include <Library/UefiRuntimeServicesTableLib.h> + +#include <Protocol/EmbeddedGpio.h> +#include <Protocol/DwUsb.h> + +#include <Hi6220.h> + + +#define USB_SEL_GPIO0_3 3 // GPIO 0_3 +#define USB_5V_HUB_EN 7 // GPIO 0_7 +#define USB_ID_DET_GPIO2_5 21 // GPIO 2_5 +#define USB_VBUS_DET_GPIO2_6 22 // GPIO 2_6 + +// Jumper on pin5-6 of J15 determines whether boot to fastboot +#define DETECT_J15_FASTBOOT 24 // GPIO 3_0 + +STATIC EMBEDDED_GPIO *mGpio; + +STATIC +VOID +HiKeyDetectUsbModeInit ( + IN VOID + ) +{ + EFI_STATUS Status; + + /* set pullup on both GPIO2_5 & GPIO2_6. It's required for inupt. */ + MmioWrite32 (0xf8001864, 1); + MmioWrite32 (0xf8001868, 1); + + Status = gBS->LocateProtocol (&gEmbeddedGpioProtocolGuid, NULL, (VOID **)&mGpio); + ASSERT_EFI_ERROR (Status); + Status = mGpio->Set (mGpio, USB_SEL_GPIO0_3, GPIO_MODE_OUTPUT_0); + ASSERT_EFI_ERROR (Status); + Status = mGpio->Set (mGpio, USB_5V_HUB_EN, GPIO_MODE_OUTPUT_0); + ASSERT_EFI_ERROR (Status); + MicroSecondDelay (1000); + + Status = mGpio->Set (mGpio, USB_ID_DET_GPIO2_5, GPIO_MODE_INPUT); + ASSERT_EFI_ERROR (Status); + Status = mGpio->Set (mGpio, USB_VBUS_DET_GPIO2_6, GPIO_MODE_INPUT); + ASSERT_EFI_ERROR (Status); +} + +UINTN +HiKeyGetUsbMode ( + IN VOID + ) +{ +#if 0 + EFI_STATUS Status; + UINTN GpioId, GpioVbus; + UINTN Value; + + Status = mGpio->Get (mGpio, USB_ID_DET_GPIO2_5, &Value); + ASSERT_EFI_ERROR (Status); + GpioId = Value; + Status = mGpio->Get (mGpio, USB_VBUS_DET_GPIO2_6, &Value); + ASSERT_EFI_ERROR (Status); + GpioVbus = Value; + +DEBUG ((DEBUG_ERROR, "#%a, %d, GpioId:%d, GpioVbus:%d\n", __func__, __LINE__, GpioId, GpioVbus)); + if ((GpioId == 1) && (GpioVbus == 0)) { + return USB_DEVICE_MODE; + } else if ((GpioId == 0) && (GpioVbus == 1)) { + return USB_CABLE_NOT_ATTACHED; + } + return USB_HOST_MODE; +#else + return USB_DEVICE_MODE; +#endif +} + +EFI_STATUS +HiKeyUsbPhyInit ( + IN UINT8 Mode + ) +{ + UINTN Value; + UINT32 Data; + + HiKeyDetectUsbModeInit (); + + //setup clock + MmioWrite32 (PERI_CTRL_BASE + SC_PERIPH_CLKEN0, BIT4); + do { + Value = MmioRead32 (PERI_CTRL_BASE + SC_PERIPH_CLKSTAT0); + } while ((Value & BIT4) == 0); + + //setup phy + Data = RST0_USBOTG_BUS | RST0_POR_PICOPHY | + RST0_USBOTG | RST0_USBOTG_32K; + MmioWrite32 (PERI_CTRL_BASE + SC_PERIPH_RSTDIS0, Data); + do { + Value = MmioRead32 (PERI_CTRL_BASE + SC_PERIPH_RSTSTAT0); + Value &= Data; + } while (Value); + + Value = MmioRead32 (PERI_CTRL_BASE + SC_PERIPH_CTRL4); + Value &= ~(CTRL4_PICO_SIDDQ | CTRL4_FPGA_EXT_PHY_SEL | + CTRL4_OTG_PHY_SEL); + Value |= CTRL4_PICO_VBUSVLDEXT | CTRL4_PICO_VBUSVLDEXTSEL; + MmioWrite32 (PERI_CTRL_BASE + SC_PERIPH_CTRL4, Value); + MicroSecondDelay (1000); + + //If Mode = 1, USB in Device Mode + //If Mode = 0, USB in Host Mode + if (Mode == USB_DEVICE_MODE) { + if (HiKeyGetUsbMode () == USB_DEVICE_MODE) { + DEBUG ((DEBUG_ERROR, "usb work as device mode.\n")); + } else { + return EFI_INVALID_PARAMETER; + } + + Value = MmioRead32 (PERI_CTRL_BASE + SC_PERIPH_CTRL5); + Value &= ~CTRL5_PICOPHY_BC_MODE; + MmioWrite32 (PERI_CTRL_BASE + SC_PERIPH_CTRL5, Value); + MicroSecondDelay (20000); + } else { + if (HiKeyGetUsbMode () == USB_HOST_MODE) { + DEBUG ((DEBUG_ERROR, "usb work as host mode.\n")); + } else { + return EFI_INVALID_PARAMETER; + } + + /*CTRL5*/ + Data = MmioRead32 (PERI_CTRL_BASE + SC_PERIPH_CTRL5); + Data &= ~CTRL5_PICOPHY_BC_MODE; + Data |= CTRL5_USBOTG_RES_SEL | CTRL5_PICOPHY_ACAENB | + CTRL5_PICOPHY_VDATDETENB | CTRL5_PICOPHY_DCDENB; + MmioWrite32 (PERI_CTRL_BASE + SC_PERIPH_CTRL5, Data); + MicroSecondDelay (20000); + MmioWrite32 (PERI_CTRL_BASE + 0x018, 0x70533483); //EYE_PATTERN + + MicroSecondDelay (5000); + } + + return EFI_SUCCESS; +} + +EFI_STATUS +EFIAPI +HiKeyUsbGetLang ( + OUT CHAR16 *Lang, + OUT UINT8 *Length + ) +{ + if ((Lang == NULL) || (Length == NULL)) { + return EFI_INVALID_PARAMETER; + } + Lang[0] = 0x409; + *Length = sizeof (CHAR16); + return EFI_SUCCESS; +} + +EFI_STATUS +EFIAPI +HiKeyUsbGetManuFacturer ( + OUT CHAR16 *ManuFacturer, + OUT UINT8 *Length + ) +{ + UINTN VariableSize; + CHAR16 DataUnicode[MANU_FACTURER_STRING_LENGTH]; + + if ((ManuFacturer == NULL) || (Length == NULL)) { + return EFI_INVALID_PARAMETER; + } + VariableSize = MANU_FACTURER_STRING_LENGTH * sizeof (CHAR16); + ZeroMem (DataUnicode, MANU_FACTURER_STRING_LENGTH * sizeof(CHAR16)); + StrCpy (DataUnicode, L"96Boards"); + CopyMem (ManuFacturer, DataUnicode, VariableSize); + *Length = VariableSize; + return EFI_SUCCESS; +} + +EFI_STATUS +EFIAPI +HiKeyUsbGetProduct ( + OUT CHAR16 *Product, + OUT UINT8 *Length + ) +{ + UINTN VariableSize; + CHAR16 DataUnicode[PRODUCT_STRING_LENGTH]; + + if ((Product == NULL) || (Length == NULL)) { + return EFI_INVALID_PARAMETER; + } + VariableSize = PRODUCT_STRING_LENGTH * sizeof (CHAR16); + ZeroMem (DataUnicode, PRODUCT_STRING_LENGTH * sizeof(CHAR16)); + StrCpy (DataUnicode, L"HiKey"); + CopyMem (Product, DataUnicode, VariableSize); + *Length = VariableSize; + return EFI_SUCCESS; +} + +EFI_STATUS +EFIAPI +HiKeyUsbGetSerialNo ( + OUT CHAR16 *SerialNo, + OUT UINT8 *Length + ) +{ + UINTN VariableSize; + CHAR16 DataUnicode[SERIAL_STRING_LENGTH]; + + if ((SerialNo == NULL) || (Length == NULL)) { + return EFI_INVALID_PARAMETER; + } + VariableSize = SERIAL_STRING_LENGTH * sizeof (CHAR16); + ZeroMem (DataUnicode, SERIAL_STRING_LENGTH * sizeof(CHAR16)); + StrCpy (DataUnicode, L"0123456789abcdef"); + CopyMem (SerialNo, DataUnicode, VariableSize); + *Length = VariableSize; + return EFI_SUCCESS; +} + +DW_USB_PROTOCOL mDwUsbDevice = { + HiKeyUsbGetLang, + HiKeyUsbGetManuFacturer, + HiKeyUsbGetProduct, + HiKeyUsbGetSerialNo, + HiKeyUsbPhyInit +}; + +EFI_STATUS +EFIAPI +HiKeyUsbEntryPoint ( + IN EFI_HANDLE ImageHandle, + IN EFI_SYSTEM_TABLE *SystemTable + ) +{ + EFI_STATUS Status; + + Status = gBS->InstallProtocolInterface ( + &ImageHandle, + &gDwUsbProtocolGuid, + EFI_NATIVE_INTERFACE, + &mDwUsbDevice + ); + if (EFI_ERROR (Status)) { + return Status; + } + return Status; +} diff --git a/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.inf b/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.inf new file mode 100644 index 0000000..75ff599 --- /dev/null +++ b/Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.inf @@ -0,0 +1,46 @@ +#/** @file +# +# Copyright (c) 2015-2017, Linaro. All rights reserved. +# +# This program and the accompanying materials +# are licensed and made available under the terms and conditions of the BSD License +# which accompanies this distribution. The full text of the license may be found at +# http://opensource.org/licenses/bsd-license.php +# THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, +# WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. +# +# +#**/ + +[Defines] + INF_VERSION = 0x00010019 + BASE_NAME = HiKeyUsbDxe + FILE_GUID = c5c7089e-9b00-448c-8b23-a552688e2833 + MODULE_TYPE = UEFI_DRIVER + VERSION_STRING = 1.0 + ENTRY_POINT = HiKeyUsbEntryPoint + +[Sources.common] + HiKeyUsbDxe.c + +[LibraryClasses] + DebugLib + IoLib + TimerLib + UefiBootServicesTableLib + UefiDriverEntryPoint + +[Protocols] + gDwUsbProtocolGuid + gEfiDriverBindingProtocolGuid + gEmbeddedGpioProtocolGuid + +[Packages] + MdePkg/MdePkg.dec + MdeModulePkg/MdeModulePkg.dec + EmbeddedPkg/EmbeddedPkg.dec + OpenPlatformPkg/Drivers/Usb/DwUsbDxe/DwUsbDxe.dec + OpenPlatformPkg/Platforms/Hisilicon/HiKey/HiKey.dec + +[Depex] + BEFORE gDwUsbDeviceGuid
Support Designware USB device controller on HiKey platform. Contributed-under: TianoCore Contribution Agreement 1.0 Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org> --- .../Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.c | 266 +++++++++++++++++++++ .../Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.inf | 46 ++++ 2 files changed, 312 insertions(+) create mode 100644 Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.c create mode 100644 Platforms/Hisilicon/HiKey/HiKeyUsbDxe/HiKeyUsbDxe.inf