@@ -90,6 +90,15 @@ config MSM_GCC_8660
Say Y if you want to use peripheral devices such as UART, SPI,
i2c, USB, SD/eMMC, etc.
+config MSM_LCC_8660
+ tristate "MSM8660 LPASS Clock Controller"
+ select MSM_GCC_8660
+ depends on COMMON_CLK_QCOM
+ help
+ Support for the Low-power Audio Subsystem (LPASS) clock controller
+ on MSM8660 devices.
+ Say Y if you want to use audio devices such as I2S and PCM.
+
config MSM_GCC_8916
tristate "MSM8916 Global Clock Controller"
select QCOM_GDSC
@@ -21,6 +21,7 @@ obj-$(CONFIG_IPQ_LCC_806X) += lcc-ipq806x.o
obj-$(CONFIG_MDM_GCC_9615) += gcc-mdm9615.o
obj-$(CONFIG_MDM_LCC_9615) += lcc-mdm9615.o
obj-$(CONFIG_MSM_GCC_8660) += gcc-msm8660.o
+obj-$(CONFIG_MSM_LCC_8660) += lcc-msm8660.o
obj-$(CONFIG_MSM_GCC_8916) += gcc-msm8916.o
obj-$(CONFIG_MSM_GCC_8960) += gcc-msm8960.o
obj-$(CONFIG_MSM_GCC_8974) += gcc-msm8974.o
new file mode 100644
@@ -0,0 +1,418 @@
+/*
+ * Qualcomm MSM8660/APQ8060 Low-power Audio Subsystem (LPASS) Clock Controller
+ * Copyright (c) 2017 Linus Walleij <linus.walleij@linaro.org>
+ *
+ * Based on a copy of the IPQ806x driver
+ * (C) 2014 Rajendra Nayak
+ * and portions of the MDM9615 driver
+ * (C) 2014 Neil Armstrong.
+ */
+
+#include <linux/kernel.h>
+#include <linux/bitops.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/clk-provider.h>
+#include <linux/regmap.h>
+
+#include <dt-bindings/clock/qcom,lcc-msm8660.h>
+
+#include "common.h"
+#include "clk-regmap.h"
+#include "clk-pll.h"
+#include "clk-rcg.h"
+#include "clk-branch.h"
+#include "clk-regmap-divider.h"
+#include "clk-regmap-mux.h"
+
+/*
+ * The vendor tree calls this "PLL0" but we are going to refer to it as
+ * LPA_PLL0 so as not to confuse it with the PLL0 on the GCC.
+ */
+static struct clk_pll lpa_pll0 = {
+ .l_reg = 0x4,
+ .m_reg = 0x8,
+ .n_reg = 0xc,
+ .config_reg = 0x14,
+ .mode_reg = 0x0,
+ .status_reg = 0x18,
+ .status_bit = 16,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "lpa_pll0",
+ .parent_names = (const char *[]){ "pxo" },
+ .num_parents = 1,
+ .ops = &clk_pll_ops,
+ },
+};
+
+/*
+ * The l/m/n values were read out of the registers after a cold boot.
+ * The config register read 00c22080 and the mode register 0x00000007.
+ */
+static const struct pll_config lpa_pll0_config = {
+ .l = 0xf,
+ .m = 0x1c,
+ .n = 0x465,
+ .vco_val = BIT(17),
+ .vco_mask = BIT(17) | BIT(16),
+ .pre_div_val = 0x0,
+ .pre_div_mask = BIT(19),
+ .post_div_val = 0x0,
+ .post_div_mask = BIT(21) | BIT(20),
+ .mn_ena_mask = BIT(22),
+ .main_output_mask = BIT(23),
+};
+
+enum {
+ P_PXO,
+ P_CXO,
+ P_PLL4_LPA_PLL0,
+ P_GND,
+};
+
+/* The vendor code uses PLL4 as parent everywhere */
+static const struct parent_map lcc_parent_map[] = {
+ { P_PXO, 0 },
+ { P_CXO, 1 },
+ /* Select RPM PLL4, but also used for selecting LPA PLL0 */
+ { P_PLL4_LPA_PLL0, 2 },
+ /* Will just ground the line */
+ { P_GND, 6 },
+};
+
+static const char * const lcc_parent_tbl[] = {
+ "pxo",
+ "cxo",
+ /*
+ * PLL4 is an RPM clock on MSM8660/APQ8060, set to "pll4" for this
+ * If we enable and mux in the LPA_PLL0 on this platform, we can
+ * set this to "lpa_pll0" instead
+ */
+ "pll4_clk",
+ "gnd", /* This is a very inactive parent */
+};
+
+/*
+ * This table is evidently for using PLL4 as parent, if we start using
+ * LPA_PLL0 we need to provide a second table.
+ */
+static struct freq_tbl clk_tbl_aif_osr_pll4[] = {
+ { 768000, P_PLL4_LPA_PLL0, 4, 1, 176 },
+ { 1024000, P_PLL4_LPA_PLL0, 4, 1, 132 },
+ { 1536000, P_PLL4_LPA_PLL0, 4, 1, 88 },
+ { 2048000, P_PLL4_LPA_PLL0, 4, 1, 66 },
+ { 3072000, P_PLL4_LPA_PLL0, 4, 1, 44 },
+ { 4096000, P_PLL4_LPA_PLL0, 4, 1, 33 },
+ { 6144000, P_PLL4_LPA_PLL0, 4, 1, 22 },
+ { 8192000, P_PLL4_LPA_PLL0, 2, 1, 33 },
+ { 12288000, P_PLL4_LPA_PLL0, 4, 1, 11 },
+ { 24576000, P_PLL4_LPA_PLL0, 2, 1, 11 },
+ { 27000000, P_PXO, 1, 0, 0 },
+ { }
+};
+
+/*
+ * This macro is modified from lcc-mdm9516.c, it's used for all the
+ * AIF clocks, all of them have an OSR clock and a bit clock derived
+ * from the OSR clock.
+ *
+ * These clocks differ from many other platforms by using
+ * BRANCH_HALT_DELAY for the *_bit_div_clk
+ */
+#define CLK_AIF_OSR_DIV(prefix, _ns, _md, _hr) \
+static struct clk_rcg prefix##_osr_src = { \
+ .ns_reg = _ns, \
+ .md_reg = _md, \
+ .mn = { \
+ .mnctr_en_bit = 8, \
+ .mnctr_reset_bit = 7, \
+ .mnctr_mode_shift = 5, \
+ .n_val_shift = 24, \
+ .m_val_shift = 8, \
+ .width = 8, \
+ }, \
+ .p = { \
+ .pre_div_shift = 3, \
+ .pre_div_width = 2, \
+ }, \
+ .s = { \
+ .src_sel_shift = 0, \
+ .parent_map = lcc_parent_map, \
+ }, \
+ .freq_tbl = clk_tbl_aif_osr_pll4, \
+ .clkr = { \
+ .enable_reg = _ns, \
+ .enable_mask = BIT(9), \
+ .hw.init = &(struct clk_init_data){ \
+ .name = #prefix "_osr_src", \
+ .parent_names = lcc_parent_tbl, \
+ .num_parents = 4, \
+ .ops = &clk_rcg_ops, \
+ .flags = CLK_SET_RATE_GATE, \
+ }, \
+ }, \
+}; \
+ \
+static const char * const lcc_##prefix##_parents[] = { \
+ #prefix "_osr_src", \
+}; \
+ \
+static struct clk_branch prefix##_osr_clk = { \
+ .halt_reg = _hr, \
+ .halt_bit = 1, \
+ .halt_check = BRANCH_HALT_ENABLE, \
+ .clkr = { \
+ .enable_reg = _ns, \
+ .enable_mask = BIT(17), \
+ .hw.init = &(struct clk_init_data){ \
+ .name = #prefix "_osr_clk", \
+ .parent_names = lcc_##prefix##_parents, \
+ .num_parents = 1, \
+ .ops = &clk_branch_ops, \
+ .flags = CLK_SET_RATE_PARENT, \
+ }, \
+ }, \
+}; \
+ \
+static struct clk_regmap_div prefix##_div_clk = { \
+ .reg = _ns, \
+ .shift = 10, \
+ .width = 4, \
+ .clkr = { \
+ .hw.init = &(struct clk_init_data){ \
+ .name = #prefix "_div_clk", \
+ .parent_names = lcc_##prefix##_parents, \
+ .num_parents = 1, \
+ .ops = &clk_regmap_div_ops, \
+ }, \
+ }, \
+}; \
+ \
+static struct clk_branch prefix##_bit_div_clk = { \
+ .halt_reg = _hr, \
+ .halt_bit = 0, \
+ .halt_check = BRANCH_HALT_DELAY, \
+ .clkr = { \
+ .enable_reg = _ns, \
+ .enable_mask = BIT(15), \
+ .hw.init = &(struct clk_init_data){ \
+ .name = #prefix "_bit_div_clk", \
+ .parent_names = (const char *[]){ \
+ #prefix "_div_clk" \
+ }, \
+ .num_parents = 1, \
+ .ops = &clk_branch_ops, \
+ .flags = CLK_SET_RATE_PARENT, \
+ }, \
+ }, \
+}; \
+ \
+static struct clk_regmap_mux prefix##_bit_clk = { \
+ .reg = _ns, \
+ .shift = 14, \
+ .width = 1, \
+ .clkr = { \
+ .hw.init = &(struct clk_init_data){ \
+ .name = #prefix "_bit_clk", \
+ .parent_names = (const char *[]){ \
+ #prefix "_bit_div_clk", \
+ #prefix "_codec_clk", \
+ }, \
+ .num_parents = 2, \
+ .ops = &clk_regmap_mux_closest_ops, \
+ .flags = CLK_SET_RATE_PARENT, \
+ }, \
+ }, \
+}
+
+CLK_AIF_OSR_DIV(mi2s, 0x48, 0x4c, 0x50);
+CLK_AIF_OSR_DIV(codec_i2s_mic, 0x60, 0x64, 0x68);
+CLK_AIF_OSR_DIV(spare_i2s_mic, 0x78, 0x7c, 0x80);
+CLK_AIF_OSR_DIV(codec_i2s_spkr, 0x6c, 0x70, 0x74);
+CLK_AIF_OSR_DIV(spare_i2s_spkr, 0x84, 0x88, 0x8c);
+
+/*
+ * PCM clock
+ * This table is evidently for using PLL4 as parent, if we start using
+ * LPA_PLL0 we need to provide a second table.
+ */
+static struct freq_tbl clk_tbl_pcm_pll4[] = {
+ { 512000, P_PLL4_LPA_PLL0, 4, 1, 264 },
+ { 768000, P_PLL4_LPA_PLL0, 4, 1, 176 },
+ { 1024000, P_PLL4_LPA_PLL0, 4, 1, 132 },
+ { 1536000, P_PLL4_LPA_PLL0, 4, 1, 88 },
+ { 2048000, P_PLL4_LPA_PLL0, 4, 1, 66 },
+ { 3072000, P_PLL4_LPA_PLL0, 4, 1, 44 },
+ { 4096000, P_PLL4_LPA_PLL0, 4, 1, 33 },
+ { 6144000, P_PLL4_LPA_PLL0, 4, 1, 22 },
+ { 8192000, P_PLL4_LPA_PLL0, 2, 1, 33 },
+ { 12288000, P_PLL4_LPA_PLL0, 4, 1, 11 },
+ { 24580000, P_PLL4_LPA_PLL0, 2, 1, 11 },
+ { 27000000, P_PXO, 1, 0, 0 },
+ { },
+};
+
+static struct clk_rcg pcm_src = {
+ .ns_reg = 0x54,
+ .md_reg = 0x58,
+ .mn = {
+ .mnctr_en_bit = 8,
+ .mnctr_reset_bit = 7,
+ .mnctr_mode_shift = 5,
+ .n_val_shift = 16,
+ .m_val_shift = 16,
+ .width = 16,
+ },
+ .p = {
+ .pre_div_shift = 3,
+ .pre_div_width = 2,
+ },
+ .s = {
+ .src_sel_shift = 0,
+ .parent_map = lcc_parent_map,
+ },
+ .freq_tbl = clk_tbl_pcm_pll4,
+ .clkr = {
+ .enable_reg = 0x54,
+ .enable_mask = BIT(9),
+ .hw.init = &(struct clk_init_data){
+ .name = "pcm_src",
+ .parent_names = lcc_parent_tbl,
+ .num_parents = 4,
+ .ops = &clk_rcg_ops,
+ .flags = CLK_SET_RATE_GATE,
+ },
+ },
+};
+
+static struct clk_branch pcm_clk_out = {
+ .halt_reg = 0x5c,
+ .halt_bit = 0,
+ .halt_check = BRANCH_HALT_ENABLE,
+ .clkr = {
+ .enable_reg = 0x54,
+ .enable_mask = BIT(11),
+ .hw.init = &(struct clk_init_data){
+ .name = "pcm_clk_out",
+ .parent_names = (const char *[]){ "pcm_src" },
+ .num_parents = 1,
+ .ops = &clk_branch_ops,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+ },
+};
+
+static struct clk_regmap_mux pcm_clk = {
+ .reg = 0x54,
+ .shift = 10,
+ .width = 1,
+ .clkr = {
+ .hw.init = &(struct clk_init_data){
+ .name = "pcm_clk",
+ .parent_names = (const char *[]){
+ "pcm_clk_out",
+ "pcm_codec_clk",
+ },
+ .num_parents = 2,
+ .ops = &clk_regmap_mux_closest_ops,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+ },
+};
+
+static struct clk_regmap *lcc_msm8660_clks[] = {
+ [LPA_PLL0] = &lpa_pll0.clkr,
+ [MI2S_OSR_SRC] = &mi2s_osr_src.clkr,
+ [MI2S_OSR_CLK] = &mi2s_osr_clk.clkr,
+ [MI2S_DIV_CLK] = &mi2s_div_clk.clkr,
+ [MI2S_BIT_DIV_CLK] = &mi2s_bit_div_clk.clkr,
+ [MI2S_BIT_CLK] = &mi2s_bit_clk.clkr,
+ [CODEC_I2S_MIC_OSR_SRC] = &codec_i2s_mic_osr_src.clkr,
+ [CODEC_I2S_MIC_OSR_CLK] = &codec_i2s_mic_osr_clk.clkr,
+ [CODEC_I2S_MIC_DIV_CLK] = &codec_i2s_mic_div_clk.clkr,
+ [CODEC_I2S_MIC_BIT_DIV_CLK] = &codec_i2s_mic_bit_div_clk.clkr,
+ [CODEC_I2S_MIC_BIT_CLK] = &codec_i2s_mic_bit_clk.clkr,
+ [SPARE_I2S_MIC_OSR_SRC] = &spare_i2s_mic_osr_src.clkr,
+ [SPARE_I2S_MIC_OSR_CLK] = &spare_i2s_mic_osr_clk.clkr,
+ [SPARE_I2S_MIC_DIV_CLK] = &spare_i2s_mic_div_clk.clkr,
+ [SPARE_I2S_MIC_BIT_DIV_CLK] = &spare_i2s_mic_bit_div_clk.clkr,
+ [SPARE_I2S_MIC_BIT_CLK] = &spare_i2s_mic_bit_clk.clkr,
+ [CODEC_I2S_SPKR_OSR_SRC] = &codec_i2s_spkr_osr_src.clkr,
+ [CODEC_I2S_SPKR_OSR_CLK] = &codec_i2s_spkr_osr_clk.clkr,
+ [CODEC_I2S_SPKR_DIV_CLK] = &codec_i2s_spkr_div_clk.clkr,
+ [CODEC_I2S_SPKR_BIT_DIV_CLK] = &codec_i2s_spkr_bit_div_clk.clkr,
+ [CODEC_I2S_SPKR_BIT_CLK] = &codec_i2s_spkr_bit_clk.clkr,
+ [SPARE_I2S_SPKR_OSR_SRC] = &spare_i2s_spkr_osr_src.clkr,
+ [SPARE_I2S_SPKR_OSR_CLK] = &spare_i2s_spkr_osr_clk.clkr,
+ [SPARE_I2S_SPKR_DIV_CLK] = &spare_i2s_spkr_div_clk.clkr,
+ [SPARE_I2S_SPKR_BIT_DIV_CLK] = &spare_i2s_spkr_bit_div_clk.clkr,
+ [SPARE_I2S_SPKR_BIT_CLK] = &spare_i2s_spkr_bit_clk.clkr,
+ [PCM_SRC] = &pcm_src.clkr,
+ [PCM_CLK_OUT] = &pcm_clk_out.clkr,
+ [PCM_CLK] = &pcm_clk.clkr,
+};
+
+static const struct regmap_config lcc_msm8660_regmap_config = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = 0xfc,
+ .fast_io = true,
+};
+
+static const struct qcom_cc_desc lcc_msm8660_desc = {
+ .config = &lcc_msm8660_regmap_config,
+ .clks = lcc_msm8660_clks,
+ .num_clks = ARRAY_SIZE(lcc_msm8660_clks),
+};
+
+static const struct of_device_id lcc_msm8660_match_table[] = {
+ { .compatible = "qcom,lcc-msm8660" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, lcc_msm8660_match_table);
+
+static int lcc_msm8660_probe(struct platform_device *pdev)
+{
+ u32 val;
+ struct regmap *regmap;
+
+ regmap = qcom_cc_map(pdev, &lcc_msm8660_desc);
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ /* Configure the rate of LPA_PLL0 if the bootloader hasn't already */
+ regmap_read(regmap, 0x0, &val);
+ if (!val) {
+ dev_info(&pdev->dev, "configuring LPA_PLL0\n");
+ clk_pll_configure_sr(&lpa_pll0, regmap, &lpa_pll0_config, true);
+ } else {
+ dev_info(&pdev->dev,
+ "LPA_PLL0 already configured\n");
+ }
+
+ /*
+ * Enable LPA_PLL0 source on the LPASS Primary PLL Mux. Incidentally
+ * this is set to 0x00000001 at boot.
+ * 0x01 = LPA_PLL0
+ */
+ regmap_write(regmap, 0xc4, 0x1);
+
+ return qcom_cc_really_probe(pdev, &lcc_msm8660_desc, regmap);
+}
+
+static struct platform_driver lcc_msm8660_driver = {
+ .probe = lcc_msm8660_probe,
+ .driver = {
+ .name = "lcc-msm8660",
+ .of_match_table = lcc_msm8660_match_table,
+ },
+};
+module_platform_driver(lcc_msm8660_driver);
+
+MODULE_DESCRIPTION("QCOM LCC MSM8660 Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:lcc-msm8660");
This adds support for the MSM8660 Low-power audio subsystem (LPASS) clock controller (LCC). This is nice when you want to have audio from the system. We currently only support using the PLL4 (which is an RPM clock) as the parent, however the LPASS has its own PLL named LPA_PLL0 that we can experiment with enabling later on, so for this reason the code contains a few hints on how to enable the LPA_PLL0. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- drivers/clk/qcom/Kconfig | 9 + drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/lcc-msm8660.c | 418 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 428 insertions(+) create mode 100644 drivers/clk/qcom/lcc-msm8660.c -- 2.9.3 -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html