[2/2] ARM: dts: add core I2C devices to the APQ8060 Dragonboard

Message ID 20170515075034.3753-1-linus.walleij@linaro.org
State New
Headers show
Series
  • Untitled series #1417
Related show

Commit Message

Linus Walleij May 15, 2017, 7:50 a.m.
The APQ8060 Dragonboard has an Atmel AT24c128 EEPROM and a
Wolfson Micro WM8903 codec connected to its GSBI8 I2C bus.
Add entries for these to the device tree. The interrupt line
from the WM8903 chip is not routed anywhere on this design
so it can not be used.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

---
 arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 49 ++++++++++++++++++++++++++
 1 file changed, 49 insertions(+)

-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Comments

Bjorn Andersson May 24, 2017, 10:18 p.m. | #1
On Mon 15 May 00:50 PDT 2017, Linus Walleij wrote:

> The APQ8060 Dragonboard has an Atmel AT24c128 EEPROM and a

> Wolfson Micro WM8903 codec connected to its GSBI8 I2C bus.

> Add entries for these to the device tree. The interrupt line

> from the WM8903 chip is not routed anywhere on this design

> so it can not be used.

> 


Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>


Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Patch hide | download patch | download mbox

diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
index 2da1413f5720..32730c4742f6 100644
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -160,6 +160,19 @@ 
 				};
 			};
 
+			dragon_gsbi8_i2c_pins: gsbi8_i2c {
+				mux {
+					pins = "gpio64", "gpio65";
+					function = "gsbi8";
+				};
+				pinconf {
+					pins = "gpio64", "gpio65";
+					drive-strength = <16>;
+					/* These have external pull-up 2.2kOhm to 1.8V */
+					bias-disable;
+				};
+			};
+
 			dragon_gsbi12_i2c_pins: gsbi12_i2c {
 				mux {
 					pins = "gpio115", "gpio116";
@@ -368,6 +381,42 @@ 
 			};
 		};
 
+		gsbi@19800000 {
+			status = "ok";
+			qcom,mode = <GSBI_PROT_I2C>;
+
+			i2c@19880000 {
+				status = "ok";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
+
+				eeprom@52 {
+					/* A 16KiB Platform ID EEPROM on the CPU carrier board */
+					compatible = "atmel,24c128";
+					reg = <0x52>;
+					vcc-supply = <&pm8058_s3>;
+					pagesize = <64>;
+				};
+				wm8903: wm8903@1a {
+					/* This Woolfson Micro device has an unrouted interrupt line */
+					compatible = "wlf,wm8903";
+					reg = <0x1a>;
+
+					AVDD-supply = <&pm8058_l16>;
+					CPVDD-supply = <&pm8058_l16>;
+					DBVDD-supply = <&pm8058_s3>;
+					DCVDD-supply = <&pm8058_l0>;
+
+					gpio-controller;
+					#gpio-cells = <2>;
+
+					micdet-cfg = <0>;
+					micdet-delay = <100>;
+					gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+				};
+			};
+		};
+
 		gsbi@19c00000 {
 			status = "ok";
 			qcom,mode = <GSBI_PROT_I2C_UART>;