| Message ID | 20200524021416.17049-1-jonathan@marek.ca |
|---|---|
| Headers | show |
| Series | phy: qcom-qmp: add V4 USB PHYs | expand |
On 24/05/2020 05:14, Jonathan Marek wrote: > The primary USB PHY on sm8250 sets some values differently for the second > lane. This makes it possible to represent that. > > Signed-off-by: Jonathan Marek <jonathan@marek.ca> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> -- With best wishes Dmitry
On 24/05/2020 05:14, Jonathan Marek wrote: > Add both the DP and UNI PHY for primary/secondary usb controllers. > > The tables are very similar to sm8150 (serdes_tbl is identical), but there > are some differences. > > Signed-off-by: Jonathan Marek <jonathan@marek.ca> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> -- With best wishes Dmitry
On Sat 23 May 19:14 PDT 2020, Jonathan Marek wrote: > The primary USB PHY on sm8250 sets some values differently for the second > lane. This makes it possible to represent that. > > Signed-off-by: Jonathan Marek <jonathan@marek.ca> > --- > drivers/phy/qualcomm/phy-qcom-qmp.c | 52 ++++++++++++++++++++++------- > 1 file changed, 40 insertions(+), 12 deletions(-) > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c > index e91040af3394..b3e07afca3ca 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c > @@ -82,20 +82,34 @@ struct qmp_phy_init_tbl { > * register part of layout ? > * if yes, then offset gives index in the reg-layout > */ > - int in_layout; > + bool in_layout; > + /* > + * mask of lanes for which this register is written > + * for cases when second lane needs different values > + */ > + u8 lane_mask; > }; > > #define QMP_PHY_INIT_CFG(o, v) \ > { \ > .offset = o, \ > .val = v, \ > + .lane_mask = 0xff, \ > } > > #define QMP_PHY_INIT_CFG_L(o, v) \ > { \ > .offset = o, \ > .val = v, \ > - .in_layout = 1, \ > + .in_layout = true, \ > + .lane_mask = 0xff, \ > + } > + > +#define QMP_PHY_INIT_CFG_LANE(o, v, l) \ > + { \ > + .offset = o, \ > + .val = v, \ > + .lane_mask = l, \ > } > > /* set of registers with offsets different per-PHY */ > @@ -1986,10 +2000,11 @@ static const struct qmp_phy_cfg sm8150_usb3phy_cfg = { > .is_dual_lane_phy = true, > }; > > -static void qcom_qmp_phy_configure(void __iomem *base, > - const unsigned int *regs, > - const struct qmp_phy_init_tbl tbl[], > - int num) > +static void qcom_qmp_phy_configure_lane(void __iomem *base, > + const unsigned int *regs, > + const struct qmp_phy_init_tbl tbl[], > + int num, > + u8 lane_mask) > { > int i; > const struct qmp_phy_init_tbl *t = tbl; > @@ -1998,6 +2013,9 @@ static void qcom_qmp_phy_configure(void __iomem *base, > return; > > for (i = 0; i < num; i++, t++) { > + if (!(t->lane_mask & lane_mask)) > + continue; > + > if (t->in_layout) > writel(t->val, base + regs[t->offset]); > else > @@ -2005,6 +2023,14 @@ static void qcom_qmp_phy_configure(void __iomem *base, > } > } > > +static void qcom_qmp_phy_configure(void __iomem *base, > + const unsigned int *regs, > + const struct qmp_phy_init_tbl tbl[], > + int num) > +{ > + qcom_qmp_phy_configure_lane(base, regs, tbl, num, 0xff); > +} > + > static int qcom_qmp_phy_com_init(struct qmp_phy *qphy) > { > struct qcom_qmp *qmp = qphy->qmp; > @@ -2219,16 +2245,18 @@ static int qcom_qmp_phy_enable(struct phy *phy) > } > > /* Tx, Rx, and PCS configurations */ > - qcom_qmp_phy_configure(tx, cfg->regs, cfg->tx_tbl, cfg->tx_tbl_num); > + qcom_qmp_phy_configure_lane(tx, cfg->regs, > + cfg->tx_tbl, cfg->tx_tbl_num, 1); Please ignore the 80-char suggestion and keep this on one line. With that... Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Regards, Bjorn > /* Configuration for other LANE for USB-DP combo PHY */ > if (cfg->is_dual_lane_phy) > - qcom_qmp_phy_configure(qphy->tx2, cfg->regs, > - cfg->tx_tbl, cfg->tx_tbl_num); > + qcom_qmp_phy_configure_lane(qphy->tx2, cfg->regs, > + cfg->tx_tbl, cfg->tx_tbl_num, 2); > > - qcom_qmp_phy_configure(rx, cfg->regs, cfg->rx_tbl, cfg->rx_tbl_num); > + qcom_qmp_phy_configure_lane(rx, cfg->regs, > + cfg->rx_tbl, cfg->rx_tbl_num, 1); > if (cfg->is_dual_lane_phy) > - qcom_qmp_phy_configure(qphy->rx2, cfg->regs, > - cfg->rx_tbl, cfg->rx_tbl_num); > + qcom_qmp_phy_configure_lane(qphy->rx2, cfg->regs, > + cfg->rx_tbl, cfg->rx_tbl_num, 2); > > qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num); > ret = reset_control_deassert(qmp->ufs_reset); > -- > 2.26.1 >
On Sat 23 May 19:14 PDT 2020, Jonathan Marek wrote: > Add both the DP and UNI PHY for primary/secondary usb controllers. > > The tables are very similar to sm8150 (serdes_tbl is identical), but there > are some differences. > > Signed-off-by: Jonathan Marek <jonathan@marek.ca> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Regards, Bjorn > --- > drivers/phy/qualcomm/phy-qcom-qmp.c | 206 ++++++++++++++++++++++++++++ > drivers/phy/qualcomm/phy-qcom-qmp.h | 2 + > 2 files changed, 208 insertions(+) > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c > index 9367f8f793b5..8a597cedfebe 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c > @@ -1532,6 +1532,142 @@ static const struct qmp_phy_init_tbl sm8150_usb3_uniphy_pcs_tbl[] = { > QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c), > }; > > +static const struct qmp_phy_init_tbl sm8250_usb3_tx_tbl[] = { > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_TX, 0x60), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_RX, 0x60), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x11), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX, 0x02), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0xd5), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12), > + QMP_PHY_INIT_CFG_LANE(QSERDES_V4_TX_PI_QEC_CTRL, 0x40, 1), > + QMP_PHY_INIT_CFG_LANE(QSERDES_V4_TX_PI_QEC_CTRL, 0x54, 2), > +}; > + > +static const struct qmp_phy_init_tbl sm8250_usb3_rx_tbl[] = { > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x06), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e), > + QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_LOW, 0xff, 1), > + QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_LOW, 0x7f, 2), > + QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x7f, 1), > + QMP_PHY_INIT_CFG_LANE(QSERDES_V4_RX_RX_MODE_00_HIGH, 0xff, 2), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0x7f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x97), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x7b), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb4), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_AUX_DATA_TCOARSE_TFINE, 0xa0), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_VTH_CODE, 0x10), > +}; > + > +static const struct qmp_phy_init_tbl sm8250_usb3_pcs_tbl[] = { > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xa9), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0a), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_LFPS_DET_HIGH_COUNT_VAL, 0xf8), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_RXEQTRAINING_DFE_TIME_S2, 0x07), > +}; > + > +static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_tx_tbl[] = { > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0xd5), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_2, 0x82), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PI_QEC_CTRL, 0x40), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x11), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX, 0x02), > +}; > + > +static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_rx_tbl[] = { > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0xb8), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0xff), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xbf), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x7f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x7f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb4), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x7b), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0x5c), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xdc), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xdc), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x99), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH1, 0x04), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_THRESH2, 0x08), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN1, 0x05), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SB2_GAIN2, 0x05), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x2f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0xff), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x0f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0a), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x54), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x0c), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0a), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x47), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x04), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x0e), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x06), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1f), > +}; > + > +static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_pcs_tbl[] = { > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG1, 0xd0), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG2, 0x07), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG3, 0x20), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_LOCK_DETECT_CONFIG6, 0x13), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0xa9), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCS_TX_RX_CONFIG, 0x0c), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_RXEQTRAINING_DFE_TIME_S2, 0x07), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_USB3_UNI_LFPS_DET_HIGH_COUNT_VAL, 0xf8), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_CDR_RESET_TIME, 0x0a), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG1, 0x88), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_ALIGN_DETECT_CONFIG2, 0x13), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG1, 0x4b), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x10), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21), > +}; > + > /* struct qmp_phy_cfg - per-PHY initialization config */ > struct qmp_phy_cfg { > /* phy-type - PCIE/UFS/USB */ > @@ -1700,6 +1836,11 @@ static const char * const qmp_v4_phy_clk_l[] = { > "aux", "ref_clk_src", "ref", "com_aux", > }; > > +/* the primary usb3 phy on sm8250 doesn't have a ref clock */ > +static const char * const qmp_v4_sm8250_usbphy_clk_l[] = { > + "aux", "ref_clk_src", "com_aux" > +}; > + > static const char * const sdm845_ufs_phy_clk_l[] = { > "ref", "ref_aux", > }; > @@ -2147,6 +2288,65 @@ static const struct qmp_phy_cfg sm8150_usb3_uniphy_cfg = { > .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX, > }; > > +static const struct qmp_phy_cfg sm8250_usb3phy_cfg = { > + .type = PHY_TYPE_USB3, > + .nlanes = 1, > + > + .serdes_tbl = sm8150_usb3_serdes_tbl, > + .serdes_tbl_num = ARRAY_SIZE(sm8150_usb3_serdes_tbl), > + .tx_tbl = sm8250_usb3_tx_tbl, > + .tx_tbl_num = ARRAY_SIZE(sm8250_usb3_tx_tbl), > + .rx_tbl = sm8250_usb3_rx_tbl, > + .rx_tbl_num = ARRAY_SIZE(sm8250_usb3_rx_tbl), > + .pcs_tbl = sm8250_usb3_pcs_tbl, > + .pcs_tbl_num = ARRAY_SIZE(sm8250_usb3_pcs_tbl), > + .clk_list = qmp_v4_sm8250_usbphy_clk_l, > + .num_clks = ARRAY_SIZE(qmp_v4_sm8250_usbphy_clk_l), > + .reset_list = msm8996_usb3phy_reset_l, > + .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), > + .vreg_list = qmp_phy_vreg_l, > + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), > + .regs = qmp_v4_usb3phy_regs_layout, > + > + .start_ctrl = SERDES_START | PCS_START, > + .pwrdn_ctrl = SW_PWRDN, > + > + .has_pwrdn_delay = true, > + .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN, > + .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX, > + > + .has_phy_dp_com_ctrl = true, > + .is_dual_lane_phy = true, > +}; > + > +static const struct qmp_phy_cfg sm8250_usb3_uniphy_cfg = { > + .type = PHY_TYPE_USB3, > + .nlanes = 1, > + > + .serdes_tbl = sm8150_usb3_uniphy_serdes_tbl, > + .serdes_tbl_num = ARRAY_SIZE(sm8150_usb3_uniphy_serdes_tbl), > + .tx_tbl = sm8250_usb3_uniphy_tx_tbl, > + .tx_tbl_num = ARRAY_SIZE(sm8250_usb3_uniphy_tx_tbl), > + .rx_tbl = sm8250_usb3_uniphy_rx_tbl, > + .rx_tbl_num = ARRAY_SIZE(sm8250_usb3_uniphy_rx_tbl), > + .pcs_tbl = sm8250_usb3_uniphy_pcs_tbl, > + .pcs_tbl_num = ARRAY_SIZE(sm8250_usb3_uniphy_pcs_tbl), > + .clk_list = qmp_v4_phy_clk_l, > + .num_clks = ARRAY_SIZE(qmp_v4_phy_clk_l), > + .reset_list = msm8996_usb3phy_reset_l, > + .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), > + .vreg_list = qmp_phy_vreg_l, > + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), > + .regs = qmp_v4_usb3_uniphy_regs_layout, > + > + .start_ctrl = SERDES_START | PCS_START, > + .pwrdn_ctrl = SW_PWRDN, > + > + .has_pwrdn_delay = true, > + .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN, > + .pwrdn_delay_max = POWER_DOWN_DELAY_US_MAX, > +}; > + > static void qcom_qmp_phy_configure_lane(void __iomem *base, > const unsigned int *regs, > const struct qmp_phy_init_tbl tbl[], > @@ -2924,6 +3124,12 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = { > }, { > .compatible = "qcom,sm8150-qmp-usb3-uni-phy", > .data = &sm8150_usb3_uniphy_cfg, > + }, { > + .compatible = "qcom,sm8250-qmp-usb3-phy", > + .data = &sm8250_usb3phy_cfg, > + }, { > + .compatible = "qcom,sm8250-qmp-usb3-uni-phy", > + .data = &sm8250_usb3_uniphy_cfg, > }, > { }, > }; > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h > index f39f7a968228..4277f592684b 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp.h > +++ b/drivers/phy/qualcomm/phy-qcom-qmp.h > @@ -364,7 +364,9 @@ > #define QSERDES_V4_TX_RES_CODE_LANE_TX 0x34 > #define QSERDES_V4_TX_RES_CODE_LANE_RX 0x38 > #define QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX 0x3c > +#define QSERDES_V4_TX_RES_CODE_LANE_OFFSET_RX 0x40 > #define QSERDES_V4_TX_LANE_MODE_1 0x84 > +#define QSERDES_V4_TX_LANE_MODE_2 0x88 > #define QSERDES_V4_TX_RCV_DETECT_LVL_2 0x9c > #define QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1 0xd8 > #define QSERDES_V4_TX_PWM_GEAR_2_DIVIDER_BAND0_1 0xdC > -- > 2.26.1 >
On 23-05-20, 22:14, Jonathan Marek wrote:
> Add support for sm8150 secondary USB PHY and both sm8250 USB PHYs.
Applied all, thanks
--
~Vinod