diff mbox series

[V5,5/7] tty: serial: qcom_geni_serial: Add interconnect support

Message ID 1588919619-21355-6-git-send-email-akashast@codeaurora.org
State Superseded
Headers show
Series None | expand

Commit Message

Akash Asthana May 8, 2020, 6:33 a.m. UTC
Get the interconnect paths for Uart based Serial Engine device
and vote according to the baud rate requirement of the driver.

Signed-off-by: Akash Asthana <akashast@codeaurora.org>
---
Changes in V2:
 - As per Bjorn's comment, removed se == NULL check from geni_serial_icc_get
 - As per Bjorn's comment, removed code to set se->icc_path* to NULL in failure
 - As per Bjorn's comment, introduced and using devm_of_icc_get API for getting
   path handle
 - As per Matthias comment, added error handling for icc_set_bw call

Changes in V3:
 - As per Matthias comment, use common library APIs defined in geni-se
   driver for ICC functionality.

Changes in V4:
 - As per Mark's comment move peak_bw guess as twice of avg_bw if
   nothing mentioned explicitly to ICC core.
 - As per Matthias's comment select core clock BW based on baud rate.
   If it's less than 115200 go for GENI_DEFAULT_BW else CORE_2X_50_MHZ

Changes in V5:
 - Add icc_enable/disable to power on/off call.
 - Save some non-zero avg/peak value to ICC core by calling geni_icc_set_bw
   from probe so that when resume/icc_enable is called NOC are running at
   some non-zero value. No need to call icc_disable after BW vote because
   console devices are expected to be in active state from the probe itself
   and qcom_geni_serial_pm(STATE_OFF) will be called for non-console ones.

 drivers/tty/serial/qcom_geni_serial.c | 31 ++++++++++++++++++++++++++++---
 1 file changed, 28 insertions(+), 3 deletions(-)
diff mbox series

Patch

diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c
index 8c5d97c..2a1da36 100644
--- a/drivers/tty/serial/qcom_geni_serial.c
+++ b/drivers/tty/serial/qcom_geni_serial.c
@@ -944,6 +944,7 @@  static void qcom_geni_serial_set_termios(struct uart_port *uport,
 	struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
 	unsigned long clk_rate;
 	u32 ver, sampling_rate;
+	unsigned int avg_bw_core;
 
 	qcom_geni_serial_stop_rx(uport);
 	/* baud rate */
@@ -965,6 +966,16 @@  static void qcom_geni_serial_set_termios(struct uart_port *uport,
 	ser_clk_cfg = SER_CLK_EN;
 	ser_clk_cfg |= clk_div << CLK_DIV_SHFT;
 
+	/*
+	 * Bump up BW vote on CPU and CORE path as driver supports FIFO mode
+	 * only.
+	 */
+	avg_bw_core = (baud > 115200) ? Bps_to_icc(CORE_2X_50_MHZ)
+						: GENI_DEFAULT_BW;
+	geni_icc_bw_init(&port->se.icc_paths[GENI_TO_CORE], avg_bw_core, 0);
+	geni_icc_bw_init(&port->se.icc_paths[CPU_TO_GENI], Bps_to_icc(baud), 0);
+	geni_icc_set_bw(&port->se);
+
 	/* parity */
 	tx_trans_cfg = readl(uport->membase + SE_UART_TX_TRANS_CFG);
 	tx_parity_cfg = readl(uport->membase + SE_UART_TX_PARITY_CFG);
@@ -1202,11 +1213,14 @@  static void qcom_geni_serial_pm(struct uart_port *uport,
 	if (old_state == UART_PM_STATE_UNDEFINED)
 		old_state = UART_PM_STATE_OFF;
 
-	if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF)
+	if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF) {
+		geni_icc_enable(&port->se);
 		geni_se_resources_on(&port->se);
-	else if (new_state == UART_PM_STATE_OFF &&
-			old_state == UART_PM_STATE_ON)
+	} else if (new_state == UART_PM_STATE_OFF &&
+			old_state == UART_PM_STATE_ON) {
 		geni_se_resources_off(&port->se);
+		geni_icc_disable(&port->se);
+	}
 }
 
 static const struct uart_ops qcom_geni_console_pops = {
@@ -1304,6 +1318,17 @@  static int qcom_geni_serial_probe(struct platform_device *pdev)
 			return -ENOMEM;
 	}
 
+	ret = geni_icc_get(&port->se, NULL);
+	if (ret)
+		return ret;
+	geni_icc_bw_init(&port->se.icc_paths[GENI_TO_CORE], GENI_DEFAULT_BW, 0);
+	geni_icc_bw_init(&port->se.icc_paths[CPU_TO_GENI], GENI_DEFAULT_BW, 0);
+
+	/* Set BW for register access */
+	ret = geni_icc_set_bw(&port->se);
+	if (ret)
+		return ret;
+
 	port->name = devm_kasprintf(uport->dev, GFP_KERNEL,
 			"qcom_geni_serial_%s%d",
 			uart_console(uport) ? "console" : "uart", uport->line);