diff mbox series

[v1,4/7] bus: mhi: core: Add support for Flash Programmer execution environment

Message ID 1617067704-28850-5-git-send-email-bbhatt@codeaurora.org
State New
Headers show
Series MHI Emergency download and flash programmer support | expand

Commit Message

Bhaumik Bhatt March 30, 2021, 1:28 a.m. UTC
From: Carl Yin <carl.yin@quectel.com>


MHI WWAN modems support downloading firmware to NAND or eMMC
using Firehose protocol with process as follows:
1. Modem boots up, enters AMSS execution environment and the
device later enters EDL (Emergency Download) mode through any
mechanism host can use such as a diag command.
2. Modem enters SYS_ERROR, MHI host handles SYS_ERROR transition.
3. EDL image for device to enter 'Flash Programmer' execution
environment is then flashed via BHI interface from host.
4. Modem enters MHI READY -> M0 and sends the Flash Programmer
execution environment change to host.
5. Following that, EDL/FIREHOSE channels (34, 35) are made
available from the host.
6. User space tool for downloading firmware image to modem over
the EDL channels using Firehose protocol. Link to USB flashing
tool: https://git.linaro.org/landing-teams/working/qualcomm/qdl.git/

Make the necessary changes to allow for this sequence to occur and
allow using the Flash Programmer execution environment.

Signed-off-by: Carl Yin <carl.yin@quectel.com>

Co-developed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>

---
 drivers/bus/mhi/core/init.c     | 2 ++
 drivers/bus/mhi/core/internal.h | 1 +
 drivers/bus/mhi/core/main.c     | 3 +++
 drivers/bus/mhi/core/pm.c       | 6 ++++++
 include/linux/mhi.h             | 4 +++-
 5 files changed, 15 insertions(+), 1 deletion(-)

-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

Comments

Loic Poulain March 30, 2021, 8:02 a.m. UTC | #1
On Tue, 30 Mar 2021 at 03:28, Bhaumik Bhatt <bbhatt@codeaurora.org> wrote:
>

> From: Carl Yin <carl.yin@quectel.com>

>

> MHI WWAN modems support downloading firmware to NAND or eMMC

> using Firehose protocol with process as follows:

> 1. Modem boots up, enters AMSS execution environment and the

> device later enters EDL (Emergency Download) mode through any

> mechanism host can use such as a diag command.

> 2. Modem enters SYS_ERROR, MHI host handles SYS_ERROR transition.

> 3. EDL image for device to enter 'Flash Programmer' execution

> environment is then flashed via BHI interface from host.

> 4. Modem enters MHI READY -> M0 and sends the Flash Programmer

> execution environment change to host.

> 5. Following that, EDL/FIREHOSE channels (34, 35) are made

> available from the host.

> 6. User space tool for downloading firmware image to modem over

> the EDL channels using Firehose protocol. Link to USB flashing

> tool: https://git.linaro.org/landing-teams/working/qualcomm/qdl.git/

>

> Make the necessary changes to allow for this sequence to occur and

> allow using the Flash Programmer execution environment.

>

> Signed-off-by: Carl Yin <carl.yin@quectel.com>

> Co-developed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>

> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>


Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Manivannan Sadhasivam March 31, 2021, 11:11 a.m. UTC | #2
On Mon, Mar 29, 2021 at 06:28:21PM -0700, Bhaumik Bhatt wrote:
> From: Carl Yin <carl.yin@quectel.com>

> 

> MHI WWAN modems support downloading firmware to NAND or eMMC

> using Firehose protocol with process as follows:

> 1. Modem boots up, enters AMSS execution environment and the

> device later enters EDL (Emergency Download) mode through any

> mechanism host can use such as a diag command.

> 2. Modem enters SYS_ERROR, MHI host handles SYS_ERROR transition.

> 3. EDL image for device to enter 'Flash Programmer' execution

> environment is then flashed via BHI interface from host.

> 4. Modem enters MHI READY -> M0 and sends the Flash Programmer

> execution environment change to host.

> 5. Following that, EDL/FIREHOSE channels (34, 35) are made

> available from the host.

> 6. User space tool for downloading firmware image to modem over

> the EDL channels using Firehose protocol. Link to USB flashing

> tool: https://git.linaro.org/landing-teams/working/qualcomm/qdl.git/

> 

> Make the necessary changes to allow for this sequence to occur and

> allow using the Flash Programmer execution environment.

> 

> Signed-off-by: Carl Yin <carl.yin@quectel.com>

> Co-developed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>

> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>


Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>


Thanks,
Mani

> ---

>  drivers/bus/mhi/core/init.c     | 2 ++

>  drivers/bus/mhi/core/internal.h | 1 +

>  drivers/bus/mhi/core/main.c     | 3 +++

>  drivers/bus/mhi/core/pm.c       | 6 ++++++

>  include/linux/mhi.h             | 4 +++-

>  5 files changed, 15 insertions(+), 1 deletion(-)

> 

> diff --git a/drivers/bus/mhi/core/init.c b/drivers/bus/mhi/core/init.c

> index 706484f..ee67712 100644

> --- a/drivers/bus/mhi/core/init.c

> +++ b/drivers/bus/mhi/core/init.c

> @@ -29,6 +29,7 @@ const char * const mhi_ee_str[MHI_EE_MAX] = {

>  	[MHI_EE_WFW] = "WFW",

>  	[MHI_EE_PTHRU] = "PASS THRU",

>  	[MHI_EE_EDL] = "EDL",

> +	[MHI_EE_FP] = "FLASH PROGRAMMER",

>  	[MHI_EE_DISABLE_TRANSITION] = "DISABLE",

>  	[MHI_EE_NOT_SUPPORTED] = "NOT SUPPORTED",

>  };

> @@ -38,6 +39,7 @@ const char * const dev_state_tran_str[DEV_ST_TRANSITION_MAX] = {

>  	[DEV_ST_TRANSITION_READY] = "READY",

>  	[DEV_ST_TRANSITION_SBL] = "SBL",

>  	[DEV_ST_TRANSITION_MISSION_MODE] = "MISSION_MODE",

> +	[DEV_ST_TRANSITION_FP] = "FLASH_PROGRAMMER",

>  	[DEV_ST_TRANSITION_SYS_ERR] = "SYS_ERR",

>  	[DEV_ST_TRANSITION_DISABLE] = "DISABLE",

>  };

> diff --git a/drivers/bus/mhi/core/internal.h b/drivers/bus/mhi/core/internal.h

> index 6f37439..b1b5f2b 100644

> --- a/drivers/bus/mhi/core/internal.h

> +++ b/drivers/bus/mhi/core/internal.h

> @@ -386,6 +386,7 @@ enum dev_st_transition {

>  	DEV_ST_TRANSITION_READY,

>  	DEV_ST_TRANSITION_SBL,

>  	DEV_ST_TRANSITION_MISSION_MODE,

> +	DEV_ST_TRANSITION_FP,

>  	DEV_ST_TRANSITION_SYS_ERR,

>  	DEV_ST_TRANSITION_DISABLE,

>  	DEV_ST_TRANSITION_MAX,

> diff --git a/drivers/bus/mhi/core/main.c b/drivers/bus/mhi/core/main.c

> index d377d07..8b68657 100644

> --- a/drivers/bus/mhi/core/main.c

> +++ b/drivers/bus/mhi/core/main.c

> @@ -831,6 +831,9 @@ int mhi_process_ctrl_ev_ring(struct mhi_controller *mhi_cntrl,

>  			case MHI_EE_AMSS:

>  				st = DEV_ST_TRANSITION_MISSION_MODE;

>  				break;

> +			case MHI_EE_FP:

> +				st = DEV_ST_TRANSITION_FP;

> +				break;

>  			case MHI_EE_RDDM:

>  				mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_EE_RDDM);

>  				write_lock_irq(&mhi_cntrl->pm_lock);

> diff --git a/drivers/bus/mhi/core/pm.c b/drivers/bus/mhi/core/pm.c

> index b65222e..7ac9dfe 100644

> --- a/drivers/bus/mhi/core/pm.c

> +++ b/drivers/bus/mhi/core/pm.c

> @@ -782,6 +782,12 @@ void mhi_pm_st_worker(struct work_struct *work)

>  		case DEV_ST_TRANSITION_MISSION_MODE:

>  			mhi_pm_mission_mode_transition(mhi_cntrl);

>  			break;

> +		case DEV_ST_TRANSITION_FP:

> +			write_lock_irq(&mhi_cntrl->pm_lock);

> +			mhi_cntrl->ee = MHI_EE_FP;

> +			write_unlock_irq(&mhi_cntrl->pm_lock);

> +			mhi_create_devices(mhi_cntrl);

> +			break;

>  		case DEV_ST_TRANSITION_READY:

>  			mhi_ready_state_transition(mhi_cntrl);

>  			break;

> diff --git a/include/linux/mhi.h b/include/linux/mhi.h

> index 8f5bf40..b16afd3 100644

> --- a/include/linux/mhi.h

> +++ b/include/linux/mhi.h

> @@ -117,6 +117,7 @@ struct mhi_link_info {

>   * @MHI_EE_WFW: WLAN firmware mode

>   * @MHI_EE_PTHRU: Passthrough

>   * @MHI_EE_EDL: Embedded downloader

> + * @MHI_EE_FP: Flash Programmer Environment

>   */

>  enum mhi_ee_type {

>  	MHI_EE_PBL,

> @@ -126,7 +127,8 @@ enum mhi_ee_type {

>  	MHI_EE_WFW,

>  	MHI_EE_PTHRU,

>  	MHI_EE_EDL,

> -	MHI_EE_MAX_SUPPORTED = MHI_EE_EDL,

> +	MHI_EE_FP,

> +	MHI_EE_MAX_SUPPORTED = MHI_EE_FP,

>  	MHI_EE_DISABLE_TRANSITION, /* local EE, not related to mhi spec */

>  	MHI_EE_NOT_SUPPORTED,

>  	MHI_EE_MAX,

> -- 

> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,

> a Linux Foundation Collaborative Project

>
diff mbox series

Patch

diff --git a/drivers/bus/mhi/core/init.c b/drivers/bus/mhi/core/init.c
index 706484f..ee67712 100644
--- a/drivers/bus/mhi/core/init.c
+++ b/drivers/bus/mhi/core/init.c
@@ -29,6 +29,7 @@  const char * const mhi_ee_str[MHI_EE_MAX] = {
 	[MHI_EE_WFW] = "WFW",
 	[MHI_EE_PTHRU] = "PASS THRU",
 	[MHI_EE_EDL] = "EDL",
+	[MHI_EE_FP] = "FLASH PROGRAMMER",
 	[MHI_EE_DISABLE_TRANSITION] = "DISABLE",
 	[MHI_EE_NOT_SUPPORTED] = "NOT SUPPORTED",
 };
@@ -38,6 +39,7 @@  const char * const dev_state_tran_str[DEV_ST_TRANSITION_MAX] = {
 	[DEV_ST_TRANSITION_READY] = "READY",
 	[DEV_ST_TRANSITION_SBL] = "SBL",
 	[DEV_ST_TRANSITION_MISSION_MODE] = "MISSION_MODE",
+	[DEV_ST_TRANSITION_FP] = "FLASH_PROGRAMMER",
 	[DEV_ST_TRANSITION_SYS_ERR] = "SYS_ERR",
 	[DEV_ST_TRANSITION_DISABLE] = "DISABLE",
 };
diff --git a/drivers/bus/mhi/core/internal.h b/drivers/bus/mhi/core/internal.h
index 6f37439..b1b5f2b 100644
--- a/drivers/bus/mhi/core/internal.h
+++ b/drivers/bus/mhi/core/internal.h
@@ -386,6 +386,7 @@  enum dev_st_transition {
 	DEV_ST_TRANSITION_READY,
 	DEV_ST_TRANSITION_SBL,
 	DEV_ST_TRANSITION_MISSION_MODE,
+	DEV_ST_TRANSITION_FP,
 	DEV_ST_TRANSITION_SYS_ERR,
 	DEV_ST_TRANSITION_DISABLE,
 	DEV_ST_TRANSITION_MAX,
diff --git a/drivers/bus/mhi/core/main.c b/drivers/bus/mhi/core/main.c
index d377d07..8b68657 100644
--- a/drivers/bus/mhi/core/main.c
+++ b/drivers/bus/mhi/core/main.c
@@ -831,6 +831,9 @@  int mhi_process_ctrl_ev_ring(struct mhi_controller *mhi_cntrl,
 			case MHI_EE_AMSS:
 				st = DEV_ST_TRANSITION_MISSION_MODE;
 				break;
+			case MHI_EE_FP:
+				st = DEV_ST_TRANSITION_FP;
+				break;
 			case MHI_EE_RDDM:
 				mhi_cntrl->status_cb(mhi_cntrl, MHI_CB_EE_RDDM);
 				write_lock_irq(&mhi_cntrl->pm_lock);
diff --git a/drivers/bus/mhi/core/pm.c b/drivers/bus/mhi/core/pm.c
index b65222e..7ac9dfe 100644
--- a/drivers/bus/mhi/core/pm.c
+++ b/drivers/bus/mhi/core/pm.c
@@ -782,6 +782,12 @@  void mhi_pm_st_worker(struct work_struct *work)
 		case DEV_ST_TRANSITION_MISSION_MODE:
 			mhi_pm_mission_mode_transition(mhi_cntrl);
 			break;
+		case DEV_ST_TRANSITION_FP:
+			write_lock_irq(&mhi_cntrl->pm_lock);
+			mhi_cntrl->ee = MHI_EE_FP;
+			write_unlock_irq(&mhi_cntrl->pm_lock);
+			mhi_create_devices(mhi_cntrl);
+			break;
 		case DEV_ST_TRANSITION_READY:
 			mhi_ready_state_transition(mhi_cntrl);
 			break;
diff --git a/include/linux/mhi.h b/include/linux/mhi.h
index 8f5bf40..b16afd3 100644
--- a/include/linux/mhi.h
+++ b/include/linux/mhi.h
@@ -117,6 +117,7 @@  struct mhi_link_info {
  * @MHI_EE_WFW: WLAN firmware mode
  * @MHI_EE_PTHRU: Passthrough
  * @MHI_EE_EDL: Embedded downloader
+ * @MHI_EE_FP: Flash Programmer Environment
  */
 enum mhi_ee_type {
 	MHI_EE_PBL,
@@ -126,7 +127,8 @@  enum mhi_ee_type {
 	MHI_EE_WFW,
 	MHI_EE_PTHRU,
 	MHI_EE_EDL,
-	MHI_EE_MAX_SUPPORTED = MHI_EE_EDL,
+	MHI_EE_FP,
+	MHI_EE_MAX_SUPPORTED = MHI_EE_FP,
 	MHI_EE_DISABLE_TRANSITION, /* local EE, not related to mhi spec */
 	MHI_EE_NOT_SUPPORTED,
 	MHI_EE_MAX,