From patchwork Fri Sep 30 18:52:34 2022 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Dmitry Baryshkov X-Patchwork-Id: 611842 Return-Path: X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on aws-us-west-2-korg-lkml-1.web.codeaurora.org Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by smtp.lore.kernel.org (Postfix) with ESMTP id DBA90C32771 for ; Fri, 30 Sep 2022 18:53:05 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S232338AbiI3SxE (ORCPT ); Fri, 30 Sep 2022 14:53:04 -0400 Received: from lindbergh.monkeyblade.net ([23.128.96.19]:38794 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S232454AbiI3SxA (ORCPT ); Fri, 30 Sep 2022 14:53:00 -0400 Received: from mail-lj1-x236.google.com (mail-lj1-x236.google.com [IPv6:2a00:1450:4864:20::236]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id 4D72F1664BC for ; Fri, 30 Sep 2022 11:52:55 -0700 (PDT) Received: by mail-lj1-x236.google.com with SMTP id b24so5719346ljk.6 for ; Fri, 30 Sep 2022 11:52:54 -0700 (PDT) DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=linaro.org; s=google; h=content-transfer-encoding:mime-version:references:in-reply-to :message-id:date:subject:cc:to:from:from:to:cc:subject:date; bh=jrts8SArb2L0T/Qvk02DOv2eN6AIQ1KP08ybqYsrYRw=; b=YAjNXdUDjvTMOaZnvKZsUIa8Z83yTzUj1vUEbO5kNOCB0xYndllm6MaevdldZCStR7 gG2ayyZKsLMnSZ1RouD9ESiencMNUo0xoDd3VodmrBiP2W9eRbMKFe85ypBpX0nRooa/ IwObYo5VRdpAqFADPPvMVg8zFNUnDnzxQwNqwaVS6QLM0HtSeoRUYv67Y1M7x+k2xhNx iV7QpLRsq1CGrTuFs+6JDLrB5aZ5Y5hl+MN/DYYS0dLIq7MSRDkpROfBqr/NtlNOFvSl r+vq+dtW9q+0vm8fo9Qzw1hkYGnq5hVrKeQXlE3EidZFUD/TGV60vMnvBgti4GzmLfuV dxbQ== X-Google-DKIM-Signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=1e100.net; s=20210112; h=content-transfer-encoding:mime-version:references:in-reply-to :message-id:date:subject:cc:to:from:x-gm-message-state:from:to:cc :subject:date; bh=jrts8SArb2L0T/Qvk02DOv2eN6AIQ1KP08ybqYsrYRw=; b=ADQvbq0wv+UV4HDDmWwWIeKc5XS26Zql7rMWEWmHx91mrybkuyO7AmmQvSmKsCV6vs LAgBzVQpDpzYey12/hNdI+tYYbFxN6gIL7BO5OgPCe7W+JDax0NBwVSscxpYaq5OBL49 VKse/ggRFWn8rRrmXxv2vX7RKmCo5zHy+pYXRiUdd9wDAufpe8UTjIjzzSK777XlpDUD RVx8FQOVVC2AysZMLrYzkwvuH/5M6+7BertSNYOAYAs3rPgaq8K7MCkF5YdZlJNkfDaO ElVdHqfPt/GUL+EJsiMMcMexZ/uuNe9aOeeXt3xzE1ffj0uM0sSQxcDvnltohSPo4bcd heFA== X-Gm-Message-State: ACrzQf3pAjzg9Mv5n6dkuxxn3KvEnle764CtT+I3m1f+o2nL+Q5w00b1 OA9hdinatu8Rchtm5VWdH2nS5w== X-Google-Smtp-Source: AMsMyM40lncExQd3g2FxoQJRC6aGk+TZvkU0K5VtfhRvkcvCoASDU0HnTSM+zuXJ8EoZew9gy2QtXQ== X-Received: by 2002:a2e:910c:0:b0:26d:b452:44ed with SMTP id m12-20020a2e910c000000b0026db45244edmr2986901ljg.188.1664563972741; Fri, 30 Sep 2022 11:52:52 -0700 (PDT) Received: from eriador.lan ([37.153.55.125]) by smtp.gmail.com with ESMTPSA id i8-20020a056512006800b00492cfecf1c0sm374703lfo.245.2022.09.30.11.52.52 (version=TLS1_3 cipher=TLS_AES_256_GCM_SHA384 bits=256/256); Fri, 30 Sep 2022 11:52:52 -0700 (PDT) From: Dmitry Baryshkov To: Andy Gross , Bjorn Andersson , Konrad Dybcio , Rob Herring , Krzysztof Kozlowski Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org Subject: [PATCH 21/23] ARM: dts: qcom: apq8060-dragonboard: use labels to patch device tree Date: Fri, 30 Sep 2022 21:52:34 +0300 Message-Id: <20220930185236.867655-22-dmitry.baryshkov@linaro.org> X-Mailer: git-send-email 2.35.1 In-Reply-To: <20220930185236.867655-1-dmitry.baryshkov@linaro.org> References: <20220930185236.867655-1-dmitry.baryshkov@linaro.org> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: linux-arm-msm@vger.kernel.org Use labels to add device-specific properties to DT nodes rather than duplicating SoC DT structure in the device DT. Signed-off-by: Dmitry Baryshkov Reviewed-by: Neil Armstrong --- .../arm/boot/dts/qcom-apq8060-dragonboard.dts | 1774 ++++++++--------- arch/arm/boot/dts/qcom-msm8660.dtsi | 51 +- 2 files changed, 911 insertions(+), 914 deletions(-) diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts index dd409ff31e21..0baf202a82ba 100644 --- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts +++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts @@ -81,927 +81,923 @@ cm3605 { pinctrl-names = "default"; pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>; }; +}; - soc { - pinctrl@800000 { - /* eMMC pins, all 8 data lines connected */ - dragon_sdcc1_pins: sdcc1 { - mux { - pins = "gpio159", "gpio160", "gpio161", - "gpio162", "gpio163", "gpio164", - "gpio165", "gpio166", "gpio167", - "gpio168"; - function = "sdc1"; - }; - clk { - pins = "gpio167"; /* SDC1 CLK */ - drive-strength = <16>; - bias-disable; - }; - cmd { - pins = "gpio168"; /* SDC1 CMD */ - drive-strength = <10>; - bias-pull-up; - }; - data { - /* SDC1 D0 to D7 */ - pins = "gpio159", "gpio160", "gpio161", "gpio162", - "gpio163", "gpio164", "gpio165", "gpio166"; - drive-strength = <10>; - bias-pull-up; - }; - }; +&ebi2 { + /* The EBI2 will instantiate first, then populate its children */ + pinctrl-names = "default"; + pinctrl-0 = <&dragon_ebi2_pins>; + status = "okay"; - /* - * The SDCC3 pins are hardcoded (non-muxable) but need some pin - * configuration. - */ - dragon_sdcc3_pins: sdcc3 { - clk { - pins = "sdc3_clk"; - drive-strength = <8>; - bias-disable; - }; - cmd { - pins = "sdc3_cmd"; - drive-strength = <8>; - bias-pull-up; - }; - data { - pins = "sdc3_data"; - drive-strength = <8>; - bias-pull-up; - }; - }; + /* + * An on-board SMSC LAN9221 chip for "debug ethernet", + * which is actually just an ordinary ethernet on the + * EBI2. This has a 25MHz chrystal next to it, so no + * clocking is needed. + */ + ethernet@2,0 { + compatible = "smsc,lan9221", "smsc,lan9115"; + reg = <2 0x0 0x100>; + /* + * The second interrupt is the PME interrupt + * for network wakeup, connected to the TLMM. + */ + interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>, + <&tlmm 29 IRQ_TYPE_EDGE_RISING>; + reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>; + vdd33a-supply = <&dragon_veth>; + vddvario-supply = <&dragon_vario>; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_ethernet_gpios>; + phy-mode = "mii"; + reg-io-width = <2>; + smsc,force-external-phy; + smsc,irq-push-pull; + + /* + * SLOW chipselect config + * Delay 9 cycles (140ns@64MHz) between SMSC + * LAN9221 Ethernet controller reads and writes + * on CS2. + */ + qcom,xmem-recovery-cycles = <0>; + qcom,xmem-write-hold-cycles = <3>; + qcom,xmem-write-delta-cycles = <31>; + qcom,xmem-read-delta-cycles = <28>; + qcom,xmem-write-wait-cycles = <9>; + qcom,xmem-read-wait-cycles = <9>; + }; +}; - /* Second SD card slot pins */ - dragon_sdcc5_pins: sdcc5 { - mux { - pins = "gpio95", "gpio96", "gpio97", - "gpio98", "gpio99", "gpio100"; - function = "sdc5"; - }; - clk { - pins = "gpio97"; /* SDC5 CLK */ - drive-strength = <16>; - bias-disable; - }; - cmd { - pins = "gpio95"; /* SDC5 CMD */ - drive-strength = <10>; - bias-pull-up; - }; - data { - /* SDC5 D0 to D3 */ - pins = "gpio96", "gpio98", "gpio99", "gpio100"; - drive-strength = <10>; - bias-pull-up; - }; - }; +&gsbi3 { + qcom,mode = ; + status = "okay"; +}; - dragon_gsbi3_i2c_pins: gsbi3_i2c { - mux { - pins = "gpio43", "gpio44"; - function = "gsbi3"; - }; - pinconf { - pins = "gpio43", "gpio44"; - drive-strength = <8>; - /* These have external pull-up 2.2kOhm to 1.8V */ - bias-disable; - }; - }; +&gsbi3_i2c { + pinctrl-names = "default"; + pinctrl-0 = <&dragon_gsbi3_i2c_pins>; + status = "okay"; + + touchscreen@24 { + compatible = "cypress,cy8ctma340"; + reg = <0x24>; + /* Certainly we can do at least 400 kHz */ + clock-frequency = <400000>; + /* IRQ on GPIO61 called /CTP_INT */ + interrupt-parent = <&tlmm>; + interrupts = <61 IRQ_TYPE_EDGE_FALLING>; + /* + * The I2C bus is using a PCA9306 level translator from L16A + * to L2B so these two voltages are needed and L16A is + * kind of the IO voltage, however L16Aisn't really fed to + * the TMA340, which relies entirely on L2B (PM8901 L2). + */ + vcpin-supply = <&pm8058_l16>; + vdd-supply = <&pm8901_l2>; + /* GPIO58, called WAKE_CTP */ + reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>; + touchscreen-size-x = <480>; + touchscreen-size-y = <800>; + active-interval-ms = <0>; + touch-timeout-ms = <255>; + lowpower-interval-ms = <10>; + bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_tma340_gpios>; + }; +}; - dragon_gsbi8_i2c_pins: gsbi8_i2c { - mux { - pins = "gpio64", "gpio65"; - function = "gsbi8"; - }; - pinconf { - pins = "gpio64", "gpio65"; - drive-strength = <16>; - /* These have external pull-up 2.2kOhm to 1.8V */ - bias-disable; - }; - }; +&gsbi8 { + qcom,mode = ; + status = "okay"; +}; - dragon_gsbi12_i2c_pins: gsbi12_i2c { - mux { - pins = "gpio115", "gpio116"; - function = "gsbi12"; - }; - pinconf { - pins = "gpio115", "gpio116"; - drive-strength = <16>; - /* These have external pull-up 4.7kOhm to 1.8V */ - bias-disable; - }; - }; +&gsbi8_i2c { + pinctrl-names = "default"; + pinctrl-0 = <&dragon_gsbi8_i2c_pins>; + status = "okay"; + + eeprom@52 { + /* A 16KiB Platform ID EEPROM on the CPU carrier board */ + compatible = "atmel,24c128"; + reg = <0x52>; + vcc-supply = <&pm8058_s3>; + pagesize = <64>; + }; + wm8903: wm8903@1a { + /* This Woolfson Micro device has an unrouted interrupt line */ + compatible = "wlf,wm8903"; + reg = <0x1a>; + + AVDD-supply = <&pm8058_l16>; + CPVDD-supply = <&pm8058_l16>; + DBVDD-supply = <&pm8058_s3>; + DCVDD-supply = <&pm8058_l0>; + + gpio-controller; + #gpio-cells = <2>; + + micdet-cfg = <0>; + micdet-delay = <100>; + gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>; + }; +}; - /* Primary serial port uart 0 pins */ - dragon_gsbi12_serial_pins: gsbi12_serial { - mux { - pins = "gpio117", "gpio118"; - function = "gsbi12"; - }; - tx { - pins = "gpio117"; - drive-strength = <8>; - bias-disable; - }; - rx { - pins = "gpio118"; - drive-strength = <2>; - bias-pull-up; - }; - }; +&gsbi12 { + qcom,mode = ; + status = "okay"; +}; - dragon_ebi2_pins: ebi2 { - /* - * Pins used by EBI2 on the Dragonboard, actually only - * CS2 is used by a real peripheral. CS0 is just - * routed to a test point. - */ - mux0 { - pins = - /* "gpio39", CS1A_N this is not good to mux */ - "gpio40", /* CS2A_N */ - "gpio134"; /* CS0_N testpoint TP29 */ - function = "ebi2cs"; - }; - mux1 { - pins = - /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */ - "gpio123", "gpio124", "gpio125", "gpio126", - "gpio127", "gpio128", "gpio129", "gpio130", - /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */ - "gpio135", "gpio136", "gpio137", "gpio138", - "gpio139", "gpio140", "gpio141", "gpio142", - "gpio143", "gpio144", "gpio145", "gpio146", - "gpio147", "gpio148", "gpio149", "gpio150", - "gpio151", /* EBI2_OE_N */ - "gpio153", /* EBI2_ADV */ - "gpio157"; /* EBI2_WE_N */ - function = "ebi2"; - }; - }; +&gsbi12_serial { + pinctrl-names = "default"; + pinctrl-0 = <&dragon_gsbi12_serial_pins>; + status = "okay"; +}; - /* Interrupt line for the KXSD9 accelerometer */ - dragon_kxsd9_gpios: kxsd9 { - irq { - pins = "gpio57"; /* IRQ line */ - bias-pull-up; - }; - }; +&gsbi12_i2c { + pinctrl-names = "default"; + pinctrl-0 = <&dragon_gsbi12_i2c_pins>; + status = "okay"; + + ak8975@c { + compatible = "asahi-kasei,ak8975"; + reg = <0x0c>; + interrupt-parent = <&pm8058_gpio>; + interrupts = <33 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_ak8975_gpios>; + vid-supply = <&pm8058_lvs0>; // 1.8V + vdd-supply = <&pm8058_l14>; // 2.85V + }; + bmp085@77 { + compatible = "bosch,bmp085"; + reg = <0x77>; + interrupt-parent = <&pm8058_gpio>; + interrupts = <16 IRQ_TYPE_EDGE_RISING>; + reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_bmp085_gpios>; + vddd-supply = <&pm8058_lvs0>; // 1.8V + vdda-supply = <&pm8058_l14>; // 2.85V + }; + mpu3050@68 { + compatible = "invensense,mpu3050"; + reg = <0x68>; + /* + * GPIO17 is pulled high by a 10k + * resistor to VLOGIC so needs to be + * active low/falling edge. + */ + interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_mpu3050_gpios>; + vlogic-supply = <&pm8058_lvs0>; // 1.8V + vdd-supply = <&pm8058_l14>; // 2.85V - dragon_tma340_gpios: tma340 { - reset { - /* RESET line, TS_ATTN, WAKE_CTP */ - pins = "gpio58"; - function = "gpio"; - drive-strength = <6>; - bias-disable; - }; - irq { - pins = "gpio61"; /* IRQ line */ - function = "gpio"; - drive-strength = <2>; - bias-pull-up; - }; + /* + * The MPU-3050 acts as a hub for the + * accelerometer. + */ + i2c-gate { + #address-cells = <1>; + #size-cells = <0>; + + kxsd9@18 { + compatible = "kionix,kxsd9"; + reg = <0x18>; + interrupt-parent = <&tlmm>; + interrupts = <57 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_kxsd9_gpios>; + iovdd-supply = <&pm8058_lvs0>; // 1.8V + vdd-supply = <&pm8058_l14>; // 2.85V }; }; + }; +}; - qcom,ssbi@500000 { - pmic@0 { - keypad@148 { - linux,keymap = < - MATRIX_KEY(0, 0, KEY_MENU) - MATRIX_KEY(0, 2, KEY_1) - MATRIX_KEY(0, 3, KEY_4) - MATRIX_KEY(0, 4, KEY_7) - MATRIX_KEY(1, 0, KEY_UP) - MATRIX_KEY(1, 1, KEY_LEFT) - MATRIX_KEY(1, 2, KEY_DOWN) - MATRIX_KEY(1, 3, KEY_5) - MATRIX_KEY(1, 3, KEY_8) - MATRIX_KEY(2, 0, KEY_HOME) - MATRIX_KEY(2, 1, KEY_REPLY) - MATRIX_KEY(2, 2, KEY_2) - MATRIX_KEY(2, 3, KEY_6) - MATRIX_KEY(3, 0, KEY_VOLUMEUP) - MATRIX_KEY(3, 1, KEY_RIGHT) - MATRIX_KEY(3, 2, KEY_3) - MATRIX_KEY(3, 3, KEY_9) - MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE) - MATRIX_KEY(4, 0, KEY_VOLUMEDOWN) - MATRIX_KEY(4, 1, KEY_BACK) - MATRIX_KEY(4, 2, KEY_CAMERA) - MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE) - >; - keypad,num-rows = <6>; - keypad,num-columns = <5>; - }; - - gpio@150 { - dragon_ethernet_gpios: ethernet-state { - pinconf { - pins = "gpio7"; - function = "normal"; - input-enable; - bias-disable; - power-source = ; - }; - }; - dragon_bmp085_gpios: bmp085-state { - pinconf { - pins = "gpio16"; - function = "normal"; - input-enable; - bias-disable; - power-source = ; - }; - }; - dragon_mpu3050_gpios: mpu3050-state { - pinconf { - pins = "gpio17"; - function = "normal"; - input-enable; - bias-disable; - power-source = ; - }; - }; - dragon_sdcc3_gpios: sdcc3-state { - pinconf { - pins = "gpio22"; - function = "normal"; - input-enable; - bias-disable; - power-source = ; - }; - }; - dragon_sdcc5_gpios: sdcc5-state { - pinconf { - pins = "gpio26"; - function = "normal"; - input-enable; - bias-pull-up; - qcom,pull-up-strength = ; - power-source = ; - }; - }; - dragon_ak8975_gpios: ak8975-state { - pinconf { - pins = "gpio33"; - function = "normal"; - input-enable; - bias-disable; - power-source = ; - }; - }; - dragon_cm3605_gpios: cm3605-state { - /* Pin 34 connected to the proxy IRQ */ - gpio34-pins { - pins = "gpio34"; - function = "normal"; - input-enable; - bias-disable; - power-source = ; - }; - /* Pin 35 connected to ASET */ - gpio35-pins { - pins = "gpio35"; - function = "normal"; - output-high; - bias-disable; - power-source = ; - }; - }; - dragon_veth_gpios: veth-state { - pinconf { - pins = "gpio40"; - function = "normal"; - bias-disable; - drive-push-pull; - }; - }; - }; - - mpps@50 { - dragon_cm3605_mpps: cm3605-mpps-state { - mpp5 { - pins = "mpp5"; - function = "analog"; - input-enable; - bias-high-impedance; - /* Let's use channel 5 */ - qcom,amux-route = ; - power-source = ; - }; - }; - }; - - xoadc@197 { - /* Reference voltage 2.2 V */ - xoadc-ref-supply = <&pm8058_l18>; - - /* Board-specific channels */ - mpp5@5 { - /* Connected to AOUT of ALS sensor */ - reg = <0x00 0x05>; - }; - mpp6@6 { - /* Connected to test point TP43 */ - reg = <0x00 0x06>; - }; - mpp7@7 { - /* Connected to battery thermistor */ - reg = <0x00 0x07>; - }; - mpp8@8 { - /* Connected to battery ID detector */ - reg = <0x00 0x08>; - }; - mpp9@9 { - /* Connected to XO thermistor */ - reg = <0x00 0x09>; - }; - }; - - led@48 { - /* - * The keypad LED @0x48 is routed to - * the sensor board where it is - * connected to an infrared LED - * SFH4650 (60mW, @850nm) next to the - * ambient light and proximity sensor - * Capella Microsystems CM3605. - */ - label = "pm8058:infrared:proximitysensor"; - default-state = "off"; - linux,default-trigger = "cm3605"; - status = "okay"; - }; - led@131 { - label = "pm8058:red"; - color = ; - default-state = "off"; - status = "okay"; - }; - led@132 { - /* - * This is actually green too on my - * board, but documented as yellow. - */ - label = "pm8058:yellow"; - color = ; - default-state = "off"; - linux,default-trigger = "mmc0"; - status = "okay"; - }; - led@133 { - label = "pm8058:green"; - function = LED_FUNCTION_HEARTBEAT; - color = ; - default-state = "on"; - linux,default-trigger = "heartbeat"; - status = "okay"; - }; - }; +&pm8058_gpio { + dragon_ethernet_gpios: ethernet-state { + pinconf { + pins = "gpio7"; + function = "normal"; + input-enable; + bias-disable; + power-source = ; + }; + }; + dragon_bmp085_gpios: bmp085-state { + pinconf { + pins = "gpio16"; + function = "normal"; + input-enable; + bias-disable; + power-source = ; + }; + }; + dragon_mpu3050_gpios: mpu3050-state { + pinconf { + pins = "gpio17"; + function = "normal"; + input-enable; + bias-disable; + power-source = ; }; + }; + dragon_sdcc3_gpios: sdcc3-state { + pinconf { + pins = "gpio22"; + function = "normal"; + input-enable; + bias-disable; + power-source = ; + }; + }; + dragon_sdcc5_gpios: sdcc5-state { + pinconf { + pins = "gpio26"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,pull-up-strength = ; + power-source = ; + }; + }; + dragon_ak8975_gpios: ak8975-state { + pinconf { + pins = "gpio33"; + function = "normal"; + input-enable; + bias-disable; + power-source = ; + }; + }; + dragon_cm3605_gpios: cm3605-state { + /* Pin 34 connected to the proxy IRQ */ + gpio34-pins { + pins = "gpio34"; + function = "normal"; + input-enable; + bias-disable; + power-source = ; + }; + /* Pin 35 connected to ASET */ + gpio35-pins { + pins = "gpio35"; + function = "normal"; + output-high; + bias-disable; + power-source = ; + }; + }; + dragon_veth_gpios: veth-state { + pinconf { + pins = "gpio40"; + function = "normal"; + bias-disable; + drive-push-pull; + }; + }; +}; - gsbi@16200000 { - qcom,mode = ; - status = "okay"; +&pm8058_keypad { + linux,keymap = < + MATRIX_KEY(0, 0, KEY_MENU) + MATRIX_KEY(0, 2, KEY_1) + MATRIX_KEY(0, 3, KEY_4) + MATRIX_KEY(0, 4, KEY_7) + MATRIX_KEY(1, 0, KEY_UP) + MATRIX_KEY(1, 1, KEY_LEFT) + MATRIX_KEY(1, 2, KEY_DOWN) + MATRIX_KEY(1, 3, KEY_5) + MATRIX_KEY(1, 3, KEY_8) + MATRIX_KEY(2, 0, KEY_HOME) + MATRIX_KEY(2, 1, KEY_REPLY) + MATRIX_KEY(2, 2, KEY_2) + MATRIX_KEY(2, 3, KEY_6) + MATRIX_KEY(3, 0, KEY_VOLUMEUP) + MATRIX_KEY(3, 1, KEY_RIGHT) + MATRIX_KEY(3, 2, KEY_3) + MATRIX_KEY(3, 3, KEY_9) + MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE) + MATRIX_KEY(4, 0, KEY_VOLUMEDOWN) + MATRIX_KEY(4, 1, KEY_BACK) + MATRIX_KEY(4, 2, KEY_CAMERA) + MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE) + >; + keypad,num-rows = <6>; + keypad,num-columns = <5>; +}; - gsbi3_i2c: i2c@16280000 { - pinctrl-names = "default"; - pinctrl-0 = <&dragon_gsbi3_i2c_pins>; - status = "okay"; - - touchscreen@24 { - compatible = "cypress,cy8ctma340"; - reg = <0x24>; - /* Certainly we can do at least 400 kHz */ - clock-frequency = <400000>; - /* IRQ on GPIO61 called /CTP_INT */ - interrupt-parent = <&tlmm>; - interrupts = <61 IRQ_TYPE_EDGE_FALLING>; - /* - * The I2C bus is using a PCA9306 level translator from L16A - * to L2B so these two voltages are needed and L16A is - * kind of the IO voltage, however L16Aisn't really fed to - * the TMA340, which relies entirely on L2B (PM8901 L2). - */ - vcpin-supply = <&pm8058_l16>; - vdd-supply = <&pm8901_l2>; - /* GPIO58, called WAKE_CTP */ - reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>; - touchscreen-size-x = <480>; - touchscreen-size-y = <800>; - active-interval-ms = <0>; - touch-timeout-ms = <255>; - lowpower-interval-ms = <10>; - bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>; - pinctrl-names = "default"; - pinctrl-0 = <&dragon_tma340_gpios>; - }; - }; +&pm8058_led48 { + /* + * The keypad LED @0x48 is routed to + * the sensor board where it is + * connected to an infrared LED + * SFH4650 (60mW, @850nm) next to the + * ambient light and proximity sensor + * Capella Microsystems CM3605. + */ + label = "pm8058:infrared:proximitysensor"; + default-state = "off"; + linux,default-trigger = "cm3605"; + status = "okay"; +}; + +&pm8058_led131 { + label = "pm8058:red"; + color = ; + default-state = "off"; + status = "okay"; +}; + +&pm8058_led132 { + /* + * This is actually green too on my + * board, but documented as yellow. + */ + label = "pm8058:yellow"; + color = ; + default-state = "off"; + linux,default-trigger = "mmc0"; + status = "okay"; +}; + +&pm8058_led133 { + label = "pm8058:green"; + function = LED_FUNCTION_HEARTBEAT; + color = ; + default-state = "on"; + linux,default-trigger = "heartbeat"; + status = "okay"; +}; + +&pm8058_mpps { + dragon_cm3605_mpps: cm3605-mpps-state { + mpp5 { + pins = "mpp5"; + function = "analog"; + input-enable; + bias-high-impedance; + /* Let's use channel 5 */ + qcom,amux-route = ; + power-source = ; }; + }; +}; - gsbi@19800000 { - status = "okay"; - qcom,mode = ; +&rpm { + /* + * Set up of the PMIC RPM regulators for this board + * PM8901 supplies "preliminary regulators" whatever + * that means + */ + pm8901-regulators { + vdd_l0-supply = <&pm8901_s4>; + vdd_l1-supply = <&vph>; + vdd_l2-supply = <&vph>; + vdd_l3-supply = <&vph>; + vdd_l4-supply = <&vph>; + vdd_l5-supply = <&vph>; + vdd_l6-supply = <&vph>; + /* vdd_s0-supply, vdd_s1-supply: SAW regulators */ + vdd_s2-supply = <&vph>; + vdd_s3-supply = <&vph>; + vdd_s4-supply = <&vph>; + lvs0_in-supply = <&pm8058_s3>; + lvs1_in-supply = <&pm8901_s4>; + lvs2_in-supply = <&pm8058_l0>; + lvs3_in-supply = <&pm8058_s2>; + mvs_in-supply = <&pm8058_s3>; + + l0 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + l1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + bias-pull-down; + }; + l2 { + /* TMA340 requires strictly 3.3V */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + bias-pull-down; + }; + l3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + bias-pull-down; + }; + l4 { + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <2600000>; + bias-pull-down; + }; + l5 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + bias-pull-down; + }; + l6 { + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + bias-pull-down; + }; - i2c@19880000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&dragon_gsbi8_i2c_pins>; - - eeprom@52 { - /* A 16KiB Platform ID EEPROM on the CPU carrier board */ - compatible = "atmel,24c128"; - reg = <0x52>; - vcc-supply = <&pm8058_s3>; - pagesize = <64>; - }; - wm8903: wm8903@1a { - /* This Woolfson Micro device has an unrouted interrupt line */ - compatible = "wlf,wm8903"; - reg = <0x1a>; - - AVDD-supply = <&pm8058_l16>; - CPVDD-supply = <&pm8058_l16>; - DBVDD-supply = <&pm8058_s3>; - DCVDD-supply = <&pm8058_l0>; - - gpio-controller; - #gpio-cells = <2>; - - micdet-cfg = <0>; - micdet-delay = <100>; - gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>; - }; - }; + /* s0 and s1 are SAW regulators controlled over SPM */ + s2 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + s3 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + s4 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; }; - gsbi@19c00000 { - status = "okay"; - qcom,mode = ; + /* LVS0 thru 3 and mvs are just switches */ + lvs0 { + regulator-always-on; + }; + lvs1 { }; + lvs2 { }; + lvs3 { }; + mvs { }; - serial@19c40000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&dragon_gsbi12_serial_pins>; - }; + }; - i2c@19c80000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&dragon_gsbi12_i2c_pins>; - - ak8975@c { - compatible = "asahi-kasei,ak8975"; - reg = <0x0c>; - interrupt-parent = <&pm8058_gpio>; - interrupts = <33 IRQ_TYPE_EDGE_RISING>; - pinctrl-names = "default"; - pinctrl-0 = <&dragon_ak8975_gpios>; - vid-supply = <&pm8058_lvs0>; // 1.8V - vdd-supply = <&pm8058_l14>; // 2.85V - }; - bmp085@77 { - compatible = "bosch,bmp085"; - reg = <0x77>; - interrupt-parent = <&pm8058_gpio>; - interrupts = <16 IRQ_TYPE_EDGE_RISING>; - reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>; - pinctrl-names = "default"; - pinctrl-0 = <&dragon_bmp085_gpios>; - vddd-supply = <&pm8058_lvs0>; // 1.8V - vdda-supply = <&pm8058_l14>; // 2.85V - }; - mpu3050@68 { - compatible = "invensense,mpu3050"; - reg = <0x68>; - /* - * GPIO17 is pulled high by a 10k - * resistor to VLOGIC so needs to be - * active low/falling edge. - */ - interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>; - pinctrl-names = "default"; - pinctrl-0 = <&dragon_mpu3050_gpios>; - vlogic-supply = <&pm8058_lvs0>; // 1.8V - vdd-supply = <&pm8058_l14>; // 2.85V - - /* - * The MPU-3050 acts as a hub for the - * accelerometer. - */ - i2c-gate { - #address-cells = <1>; - #size-cells = <0>; - - kxsd9@18 { - compatible = "kionix,kxsd9"; - reg = <0x18>; - interrupt-parent = <&tlmm>; - interrupts = <57 IRQ_TYPE_EDGE_FALLING>; - pinctrl-names = "default"; - pinctrl-0 = <&dragon_kxsd9_gpios>; - iovdd-supply = <&pm8058_lvs0>; // 1.8V - vdd-supply = <&pm8058_l14>; // 2.85V - }; - }; - }; - }; + pm8058-regulators { + vdd_l0_l1_lvs-supply = <&pm8058_s3>; + vdd_l2_l11_l12-supply = <&vph>; + vdd_l3_l4_l5-supply = <&vph>; + vdd_l6_l7-supply = <&vph>; + vdd_l8-supply = <&vph>; + vdd_l9-supply = <&vph>; + vdd_l10-supply = <&vph>; + vdd_l13_l16-supply = <&pm8058_s4>; + vdd_l14_l15-supply = <&vph>; + vdd_l17_l18-supply = <&vph>; + vdd_l19_l20-supply = <&vph>; + vdd_l21-supply = <&pm8058_s3>; + vdd_l22-supply = <&pm8058_s3>; + vdd_l23_l24_l25-supply = <&pm8058_s3>; + vdd_s0-supply = <&vph>; + vdd_s1-supply = <&vph>; + vdd_s2-supply = <&vph>; + vdd_s3-supply = <&vph>; + vdd_s4-supply = <&vph>; + vdd_ncp-supply = <&vph>; + + l0 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + l1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + l2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2600000>; + bias-pull-down; + }; + l3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + l4 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + bias-pull-down; + }; + l5 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + bias-pull-down; + }; + l6 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3600000>; + bias-pull-down; + }; + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + l8 { + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <3050000>; + bias-pull-down; + }; + l9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + l10 { + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <2600000>; + bias-pull-down; + }; + l11 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + bias-pull-down; + }; + l12 { + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + bias-pull-down; + }; + l13 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + bias-pull-down; + }; + l14 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + l15 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + bias-pull-down; + }; + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + regulator-always-on; + }; + l17 { + // 1.5V according to schematic + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <2600000>; + bias-pull-down; + }; + l18 { + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + bias-pull-down; + }; + l19 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + bias-pull-down; + }; + l20 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + l21 { + // 1.1 V according to schematic + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + regulator-always-on; + }; + l22 { + // 1.2 V according to schematic + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1150000>; + bias-pull-down; + }; + l23 { + // Unused + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + l24 { + // Unused + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + l25 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; }; - external-bus@1a100000 { - /* The EBI2 will instantiate first, then populate its children */ - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&dragon_ebi2_pins>; - - /* - * An on-board SMSC LAN9221 chip for "debug ethernet", - * which is actually just an ordinary ethernet on the - * EBI2. This has a 25MHz chrystal next to it, so no - * clocking is needed. - */ - ethernet@2,0 { - compatible = "smsc,lan9221", "smsc,lan9115"; - reg = <2 0x0 0x100>; - /* - * The second interrupt is the PME interrupt - * for network wakeup, connected to the TLMM. - */ - interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>, - <&tlmm 29 IRQ_TYPE_EDGE_RISING>; - reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>; - vdd33a-supply = <&dragon_veth>; - vddvario-supply = <&dragon_vario>; - pinctrl-names = "default"; - pinctrl-0 = <&dragon_ethernet_gpios>; - phy-mode = "mii"; - reg-io-width = <2>; - smsc,force-external-phy; - smsc,irq-push-pull; - - /* - * SLOW chipselect config - * Delay 9 cycles (140ns@64MHz) between SMSC - * LAN9221 Ethernet controller reads and writes - * on CS2. - */ - qcom,xmem-recovery-cycles = <0>; - qcom,xmem-write-hold-cycles = <3>; - qcom,xmem-write-delta-cycles = <31>; - qcom,xmem-read-delta-cycles = <28>; - qcom,xmem-write-wait-cycles = <9>; - qcom,xmem-read-wait-cycles = <9>; - }; + s0 { + // regulator-min-microvolt = <500000>; + // regulator-max-microvolt = <1325000>; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + s1 { + // regulator-min-microvolt = <500000>; + // regulator-max-microvolt = <1250000>; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + s2 { + // 1.3 V according to schematic + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1400000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + s3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + qcom,switch-mode-frequency = <1600000>; + regulator-always-on; + bias-pull-down; + }; + s4 { + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + qcom,switch-mode-frequency = <1600000>; + regulator-always-on; + bias-pull-down; }; - rpm@104000 { - /* - * Set up of the PMIC RPM regulators for this board - * PM8901 supplies "preliminary regulators" whatever - * that means - */ - pm8901-regulators { - vdd_l0-supply = <&pm8901_s4>; - vdd_l1-supply = <&vph>; - vdd_l2-supply = <&vph>; - vdd_l3-supply = <&vph>; - vdd_l4-supply = <&vph>; - vdd_l5-supply = <&vph>; - vdd_l6-supply = <&vph>; - /* vdd_s0-supply, vdd_s1-supply: SAW regulators */ - vdd_s2-supply = <&vph>; - vdd_s3-supply = <&vph>; - vdd_s4-supply = <&vph>; - lvs0_in-supply = <&pm8058_s3>; - lvs1_in-supply = <&pm8901_s4>; - lvs2_in-supply = <&pm8058_l0>; - lvs3_in-supply = <&pm8058_s2>; - mvs_in-supply = <&pm8058_s3>; - - l0 { - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - bias-pull-down; - }; - l1 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - bias-pull-down; - }; - l2 { - /* TMA340 requires strictly 3.3V */ - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - bias-pull-down; - }; - l3 { - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - bias-pull-down; - }; - l4 { - regulator-min-microvolt = <2600000>; - regulator-max-microvolt = <2600000>; - bias-pull-down; - }; - l5 { - regulator-min-microvolt = <2850000>; - regulator-max-microvolt = <2850000>; - bias-pull-down; - }; - l6 { - regulator-min-microvolt = <2200000>; - regulator-max-microvolt = <2200000>; - bias-pull-down; - }; - - /* s0 and s1 are SAW regulators controlled over SPM */ - s2 { - regulator-min-microvolt = <1300000>; - regulator-max-microvolt = <1300000>; - qcom,switch-mode-frequency = <1600000>; - bias-pull-down; - }; - s3 { - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - qcom,switch-mode-frequency = <1600000>; - bias-pull-down; - }; - s4 { - regulator-min-microvolt = <1225000>; - regulator-max-microvolt = <1225000>; - qcom,switch-mode-frequency = <1600000>; - bias-pull-down; - }; - - /* LVS0 thru 3 and mvs are just switches */ - lvs0 { - regulator-always-on; - }; - lvs1 { }; - lvs2 { }; - lvs3 { }; - mvs { }; + /* LVS0 and LVS1 are just switches */ + lvs0 { + bias-pull-down; + }; + lvs1 { + bias-pull-down; + }; - }; + ncp { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + qcom,switch-mode-frequency = <1600000>; + }; + }; +}; - pm8058-regulators { - vdd_l0_l1_lvs-supply = <&pm8058_s3>; - vdd_l2_l11_l12-supply = <&vph>; - vdd_l3_l4_l5-supply = <&vph>; - vdd_l6_l7-supply = <&vph>; - vdd_l8-supply = <&vph>; - vdd_l9-supply = <&vph>; - vdd_l10-supply = <&vph>; - vdd_l13_l16-supply = <&pm8058_s4>; - vdd_l14_l15-supply = <&vph>; - vdd_l17_l18-supply = <&vph>; - vdd_l19_l20-supply = <&vph>; - vdd_l21-supply = <&pm8058_s3>; - vdd_l22-supply = <&pm8058_s3>; - vdd_l23_l24_l25-supply = <&pm8058_s3>; - vdd_s0-supply = <&vph>; - vdd_s1-supply = <&vph>; - vdd_s2-supply = <&vph>; - vdd_s3-supply = <&vph>; - vdd_s4-supply = <&vph>; - vdd_ncp-supply = <&vph>; - - l0 { - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - bias-pull-down; - }; - l1 { - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - bias-pull-down; - }; - l2 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2600000>; - bias-pull-down; - }; - l3 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - bias-pull-down; - }; - l4 { - regulator-min-microvolt = <2850000>; - regulator-max-microvolt = <2850000>; - bias-pull-down; - }; - l5 { - regulator-min-microvolt = <2850000>; - regulator-max-microvolt = <2850000>; - bias-pull-down; - }; - l6 { - regulator-min-microvolt = <3000000>; - regulator-max-microvolt = <3600000>; - bias-pull-down; - }; - l7 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - bias-pull-down; - }; - l8 { - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <3050000>; - bias-pull-down; - }; - l9 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - bias-pull-down; - }; - l10 { - regulator-min-microvolt = <2600000>; - regulator-max-microvolt = <2600000>; - bias-pull-down; - }; - l11 { - regulator-min-microvolt = <1500000>; - regulator-max-microvolt = <1500000>; - bias-pull-down; - }; - l12 { - regulator-min-microvolt = <2900000>; - regulator-max-microvolt = <2900000>; - bias-pull-down; - }; - l13 { - regulator-min-microvolt = <2050000>; - regulator-max-microvolt = <2050000>; - bias-pull-down; - }; - l14 { - regulator-min-microvolt = <2850000>; - regulator-max-microvolt = <2850000>; - }; - l15 { - regulator-min-microvolt = <2850000>; - regulator-max-microvolt = <2850000>; - bias-pull-down; - }; - l16 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - bias-pull-down; - regulator-always-on; - }; - l17 { - // 1.5V according to schematic - regulator-min-microvolt = <2600000>; - regulator-max-microvolt = <2600000>; - bias-pull-down; - }; - l18 { - regulator-min-microvolt = <2200000>; - regulator-max-microvolt = <2200000>; - bias-pull-down; - }; - l19 { - regulator-min-microvolt = <2500000>; - regulator-max-microvolt = <2500000>; - bias-pull-down; - }; - l20 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - bias-pull-down; - }; - l21 { - // 1.1 V according to schematic - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - bias-pull-down; - regulator-always-on; - }; - l22 { - // 1.2 V according to schematic - regulator-min-microvolt = <1150000>; - regulator-max-microvolt = <1150000>; - bias-pull-down; - }; - l23 { - // Unused - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - bias-pull-down; - }; - l24 { - // Unused - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - bias-pull-down; - }; - l25 { - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - bias-pull-down; - }; - - s0 { - // regulator-min-microvolt = <500000>; - // regulator-max-microvolt = <1325000>; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - qcom,switch-mode-frequency = <1600000>; - bias-pull-down; - }; - s1 { - // regulator-min-microvolt = <500000>; - // regulator-max-microvolt = <1250000>; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - qcom,switch-mode-frequency = <1600000>; - bias-pull-down; - }; - s2 { - // 1.3 V according to schematic - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1400000>; - qcom,switch-mode-frequency = <1600000>; - bias-pull-down; - }; - s3 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - qcom,switch-mode-frequency = <1600000>; - regulator-always-on; - bias-pull-down; - }; - s4 { - regulator-min-microvolt = <2200000>; - regulator-max-microvolt = <2200000>; - qcom,switch-mode-frequency = <1600000>; - regulator-always-on; - bias-pull-down; - }; - - /* LVS0 and LVS1 are just switches */ - lvs0 { - bias-pull-down; - }; - lvs1 { - bias-pull-down; - }; - - ncp { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - qcom,switch-mode-frequency = <1600000>; - }; - }; +/* Internal 3.69 GiB eMMC */ +&sdcc1 { + pinctrl-names = "default"; + pinctrl-0 = <&dragon_sdcc1_pins>; + vmmc-supply = <&pm8901_l5>; + vqmmc-supply = <&pm8901_lvs0>; + status = "okay"; +}; + +/* External micro SD card, directly connected, pulled up to 2.85 V */ +&sdcc3 { + /* Enable SSBI GPIO 22 as input, use for card detect */ + pinctrl-names = "default"; + pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>; + cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>; + wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; + vmmc-supply = <&pm8058_l14>; + status = "okay"; +}; + +/* + * Second external micro SD card, using two TXB104RGYR levelshifters + * to lift from 1.8 V to 2.85 V + */ +&sdcc5 { + /* Enable SSBI GPIO 26 as input, use for card detect */ + pinctrl-names = "default"; + pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>; + cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>; + wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>; + vmmc-supply = <&pm8058_l14>; + vqmmc-supply = <&dragon_vio_txb>; + status = "okay"; +}; + +&tlmm { + /* eMMC pins, all 8 data lines connected */ + dragon_sdcc1_pins: sdcc1 { + mux { + pins = "gpio159", "gpio160", "gpio161", + "gpio162", "gpio163", "gpio164", + "gpio165", "gpio166", "gpio167", + "gpio168"; + function = "sdc1"; }; - amba { - /* Internal 3.69 GiB eMMC */ - mmc@12400000 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&dragon_sdcc1_pins>; - vmmc-supply = <&pm8901_l5>; - vqmmc-supply = <&pm8901_lvs0>; - }; + clk { + pins = "gpio167"; /* SDC1 CLK */ + drive-strength = <16>; + bias-disable; + }; + cmd { + pins = "gpio168"; /* SDC1 CMD */ + drive-strength = <10>; + bias-pull-up; + }; + data { + /* SDC1 D0 to D7 */ + pins = "gpio159", "gpio160", "gpio161", "gpio162", + "gpio163", "gpio164", "gpio165", "gpio166"; + drive-strength = <10>; + bias-pull-up; + }; + }; - /* External micro SD card, directly connected, pulled up to 2.85 V */ - mmc@12180000 { - status = "okay"; - /* Enable SSBI GPIO 22 as input, use for card detect */ - pinctrl-names = "default"; - pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>; - cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>; - wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; - vmmc-supply = <&pm8058_l14>; - }; + /* + * The SDCC3 pins are hardcoded (non-muxable) but need some pin + * configuration. + */ + dragon_sdcc3_pins: sdcc3 { + clk { + pins = "sdc3_clk"; + drive-strength = <8>; + bias-disable; + }; + cmd { + pins = "sdc3_cmd"; + drive-strength = <8>; + bias-pull-up; + }; + data { + pins = "sdc3_data"; + drive-strength = <8>; + bias-pull-up; + }; + }; - /* - * Second external micro SD card, using two TXB104RGYR levelshifters - * to lift from 1.8 V to 2.85 V - */ - mmc@12200000 { - status = "okay"; - /* Enable SSBI GPIO 26 as input, use for card detect */ - pinctrl-names = "default"; - pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>; - cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>; - wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>; - vmmc-supply = <&pm8058_l14>; - vqmmc-supply = <&dragon_vio_txb>; - }; + /* Second SD card slot pins */ + dragon_sdcc5_pins: sdcc5 { + mux { + pins = "gpio95", "gpio96", "gpio97", + "gpio98", "gpio99", "gpio100"; + function = "sdc5"; + }; + clk { + pins = "gpio97"; /* SDC5 CLK */ + drive-strength = <16>; + bias-disable; + }; + cmd { + pins = "gpio95"; /* SDC5 CMD */ + drive-strength = <10>; + bias-pull-up; + }; + data { + /* SDC5 D0 to D3 */ + pins = "gpio96", "gpio98", "gpio99", "gpio100"; + drive-strength = <10>; + bias-pull-up; + }; + }; + + dragon_gsbi3_i2c_pins: gsbi3_i2c { + mux { + pins = "gpio43", "gpio44"; + function = "gsbi3"; + }; + pinconf { + pins = "gpio43", "gpio44"; + drive-strength = <8>; + /* These have external pull-up 2.2kOhm to 1.8V */ + bias-disable; + }; + }; + + dragon_gsbi8_i2c_pins: gsbi8_i2c { + mux { + pins = "gpio64", "gpio65"; + function = "gsbi8"; + }; + pinconf { + pins = "gpio64", "gpio65"; + drive-strength = <16>; + /* These have external pull-up 2.2kOhm to 1.8V */ + bias-disable; + }; + }; + + dragon_gsbi12_i2c_pins: gsbi12_i2c { + mux { + pins = "gpio115", "gpio116"; + function = "gsbi12"; + }; + pinconf { + pins = "gpio115", "gpio116"; + drive-strength = <16>; + /* These have external pull-up 4.7kOhm to 1.8V */ + bias-disable; + }; + }; + + /* Primary serial port uart 0 pins */ + dragon_gsbi12_serial_pins: gsbi12_serial { + mux { + pins = "gpio117", "gpio118"; + function = "gsbi12"; + }; + tx { + pins = "gpio117"; + drive-strength = <8>; + bias-disable; }; + rx { + pins = "gpio118"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + dragon_ebi2_pins: ebi2 { + /* + * Pins used by EBI2 on the Dragonboard, actually only + * CS2 is used by a real peripheral. CS0 is just + * routed to a test point. + */ + mux0 { + pins = + /* "gpio39", CS1A_N this is not good to mux */ + "gpio40", /* CS2A_N */ + "gpio134"; /* CS0_N testpoint TP29 */ + function = "ebi2cs"; + }; + mux1 { + pins = + /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */ + "gpio123", "gpio124", "gpio125", "gpio126", + "gpio127", "gpio128", "gpio129", "gpio130", + /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */ + "gpio135", "gpio136", "gpio137", "gpio138", + "gpio139", "gpio140", "gpio141", "gpio142", + "gpio143", "gpio144", "gpio145", "gpio146", + "gpio147", "gpio148", "gpio149", "gpio150", + "gpio151", /* EBI2_OE_N */ + "gpio153", /* EBI2_ADV */ + "gpio157"; /* EBI2_WE_N */ + function = "ebi2"; + }; + }; + + /* Interrupt line for the KXSD9 accelerometer */ + dragon_kxsd9_gpios: kxsd9 { + irq { + pins = "gpio57"; /* IRQ line */ + bias-pull-up; + }; + }; + + dragon_tma340_gpios: tma340 { + reset { + /* RESET line, TS_ATTN, WAKE_CTP */ + pins = "gpio58"; + function = "gpio"; + drive-strength = <6>; + bias-disable; + }; + irq { + pins = "gpio61"; /* IRQ line */ + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; +}; + +&xoadc { + /* Reference voltage 2.2 V */ + xoadc-ref-supply = <&pm8058_l18>; + + /* Board-specific channels */ + mpp5@5 { + /* Connected to AOUT of ALS sensor */ + reg = <0x00 0x05>; + }; + mpp6@6 { + /* Connected to test point TP43 */ + reg = <0x00 0x06>; + }; + mpp7@7 { + /* Connected to battery thermistor */ + reg = <0x00 0x07>; + }; + mpp8@8 { + /* Connected to battery ID detector */ + reg = <0x00 0x08>; + }; + mpp9@9 { + /* Connected to XO thermistor */ + reg = <0x00 0x09>; }; }; diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi index 35e90d188e05..4b0f58c417d5 100644 --- a/arch/arm/boot/dts/qcom-msm8660.dtsi +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi @@ -316,7 +316,7 @@ gsbi12_i2c: i2c@19c80000 { }; }; - external-bus@1a100000 { + ebi2: external-bus@1a100000 { compatible = "qcom,msm8660-ebi2"; #address-cells = <2>; #size-cells = <1>; @@ -359,12 +359,6 @@ pm8058_gpio: gpio@150 { }; - pm8058_led48: led@48 { - compatible = "qcom,pm8058-keypad-led"; - reg = <0x48>; - status = "disabled"; - }; - pm8058_mpps: mpps@50 { compatible = "qcom,pm8058-mpp", "qcom,ssbi-mpp"; @@ -385,24 +379,6 @@ pwrkey@1c { pull-up; }; - pm8058_led131: led@131 { - compatible = "qcom,pm8058-led"; - reg = <0x131>; - status = "disabled"; - }; - - pm8058_led132: led@132 { - compatible = "qcom,pm8058-led"; - reg = <0x132>; - status = "disabled"; - }; - - pm8058_led133: led@133 { - compatible = "qcom,pm8058-led"; - reg = <0x133>; - status = "disabled"; - }; - pm8058_keypad: keypad@148 { compatible = "qcom,pm8058-keypad"; reg = <0x148>; @@ -468,6 +444,31 @@ vibrator@4a { compatible = "qcom,pm8058-vib"; reg = <0x4a>; }; + + pm8058_led48: led@48 { + compatible = "qcom,pm8058-keypad-led"; + reg = <0x48>; + status = "disabled"; + }; + + pm8058_led131: led@131 { + compatible = "qcom,pm8058-led"; + reg = <0x131>; + status = "disabled"; + }; + + pm8058_led132: led@132 { + compatible = "qcom,pm8058-led"; + reg = <0x132>; + status = "disabled"; + }; + + pm8058_led133: led@133 { + compatible = "qcom,pm8058-led"; + reg = <0x133>; + status = "disabled"; + }; + }; };