diff mbox series

[05/14] phy: qcom-qmp-combo: register clocks sooner

Message ID 20221111092457.10546-6-johan+linaro@kernel.org
State New
Headers show
Series phy: qcom-qmp-combo: fix sc8280xp binding (set 3/3) | expand

Commit Message

Johan Hovold Nov. 11, 2022, 9:24 a.m. UTC
Runtime PM should be enabled before registering the PHYs, but there is
no reason that the clocks can not be registered before enabling runtime
PM.

Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

Comments

Dmitry Baryshkov Nov. 12, 2022, 11:15 a.m. UTC | #1
On 11/11/2022 12:24, Johan Hovold wrote:
> Runtime PM should be enabled before registering the PHYs, but there is
> no reason that the clocks can not be registered before enabling runtime
> PM.

This will have a side effect of DP and pipe clocks not using runtime PM 
during the clocks operations (see the code handling rpm_enabled in 
drivers/clk/clk.c). If this is an intended change, it should be 
described in the commit message.

> 
> Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
> ---
>   drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 16 ++++++++--------
>   1 file changed, 8 insertions(+), 8 deletions(-)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> index 1bc8567a8605..1a6aa61a12c5 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> @@ -2642,6 +2642,14 @@ static int qmp_combo_probe(struct platform_device *pdev)
>   	if (ret)
>   		goto err_node_put;
>   
> +	ret = phy_pipe_clk_register(qmp, usb_np);
> +	if (ret)
> +		goto err_node_put;
> +
> +	ret = phy_dp_clks_register(qmp, dp_np);
> +	if (ret)
> +		goto err_node_put;
> +
>   	pm_runtime_set_active(dev);
>   	ret = devm_pm_runtime_enable(dev);
>   	if (ret)
> @@ -2652,14 +2660,6 @@ static int qmp_combo_probe(struct platform_device *pdev)
>   	 */
>   	pm_runtime_forbid(dev);
>   
> -	ret = phy_pipe_clk_register(qmp, usb_np);
> -	if (ret)
> -		goto err_node_put;
> -
> -	ret = phy_dp_clks_register(qmp, dp_np);
> -	if (ret)
> -		goto err_node_put;
> -
>   	qmp->usb_phy = devm_phy_create(dev, usb_np, &qmp_combo_usb_phy_ops);
>   	if (IS_ERR(qmp->usb_phy)) {
>   		ret = PTR_ERR(qmp->usb_phy);
Johan Hovold Nov. 14, 2022, 1:42 p.m. UTC | #2
On Sat, Nov 12, 2022 at 02:15:04PM +0300, Dmitry Baryshkov wrote:
> On 11/11/2022 12:24, Johan Hovold wrote:
> > Runtime PM should be enabled before registering the PHYs, but there is
> > no reason that the clocks can not be registered before enabling runtime
> > PM.
> 
> This will have a side effect of DP and pipe clocks not using runtime PM 
> during the clocks operations (see the code handling rpm_enabled in 
> drivers/clk/clk.c). If this is an intended change, it should be 
> described in the commit message.

Good catch. I'll drop this one.

Johan
diff mbox series

Patch

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
index 1bc8567a8605..1a6aa61a12c5 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
@@ -2642,6 +2642,14 @@  static int qmp_combo_probe(struct platform_device *pdev)
 	if (ret)
 		goto err_node_put;
 
+	ret = phy_pipe_clk_register(qmp, usb_np);
+	if (ret)
+		goto err_node_put;
+
+	ret = phy_dp_clks_register(qmp, dp_np);
+	if (ret)
+		goto err_node_put;
+
 	pm_runtime_set_active(dev);
 	ret = devm_pm_runtime_enable(dev);
 	if (ret)
@@ -2652,14 +2660,6 @@  static int qmp_combo_probe(struct platform_device *pdev)
 	 */
 	pm_runtime_forbid(dev);
 
-	ret = phy_pipe_clk_register(qmp, usb_np);
-	if (ret)
-		goto err_node_put;
-
-	ret = phy_dp_clks_register(qmp, dp_np);
-	if (ret)
-		goto err_node_put;
-
 	qmp->usb_phy = devm_phy_create(dev, usb_np, &qmp_combo_usb_phy_ops);
 	if (IS_ERR(qmp->usb_phy)) {
 		ret = PTR_ERR(qmp->usb_phy);