| Message ID | 20230325122444.249507-12-vkoul@kernel.org |
|---|---|
| State | New |
| Headers | show |
| Series | Introduce the SC8180x devices | expand |
On 25.03.2023 13:24, Vinod Koul wrote: > From: Bjorn Andersson <bjorn.andersson@linaro.org> > > Introduce support for the SC8180X reference device, aka Primus, with > debug UART, regulators, UFS and USB support. > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > --- Please introduce PMICs in a separate commit. On top of that, the previous patch (in a very slim and basic version) should have been combined with (a very slim and basic version) this patch so that we don't introduce code that never compiles. And the patches are missing your (as the sender) S-o-bs. Please run them through dtbs_check and checkpatch.pl --strict, I think it should have pointed some of that out. Konrad > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi | 326 +++++++++ > arch/arm64/boot/dts/qcom/sc8180x-primus.dts | 706 ++++++++++++++++++++ > 3 files changed, 1033 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi > create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-primus.dts > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 31aa54f0428c..fdce44a7a902 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -141,6 +141,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-zombie-nvme-lte.dtb > dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb > dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp2.dtb > dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb > +dtb-$(CONFIG_ARCH_QCOM) += sc8180x-primus.dtb > dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb > dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-lenovo-thinkpad-x13s.dtb > dtb-$(CONFIG_ARCH_QCOM) += sda660-inforce-ifc6560.dtb > diff --git a/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi b/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi > new file mode 100644 > index 000000000000..49c146b6f37f > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi > @@ -0,0 +1,326 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. > + * Copyright (c) 2021-2022, Linaro Limited > + */ > + > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/interrupt-controller/irq.h> > +#include <dt-bindings/spmi/spmi.h> > +#include <dt-bindings/iio/qcom,spmi-vadc.h> > + > +/ { > + thermal-zones { > + pmc8180-thermal { > + polling-delay-passive = <100>; > + polling-delay = <0>; > + > + thermal-sensors = <&pmc8180_temp>; > + > + trips { > + trip0 { > + temperature = <95000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + trip1 { > + temperature = <115000>; > + hysteresis = <0>; > + type = "hot"; > + }; > + > + trip2 { > + temperature = <145000>; > + hysteresis = <0>; > + type = "critical"; > + }; > + }; > + }; > + > + pmc8180c-thermal { > + polling-delay-passive = <100>; > + polling-delay = <0>; > + > + thermal-sensors = <&pmc8180c_temp>; > + > + trips { > + trip0 { > + temperature = <95000>; > + hysteresis = <0>; > + type = "passive"; > + }; > + > + trip1 { > + temperature = <115000>; > + hysteresis = <0>; > + type = "hot"; > + }; > + > + trip2 { > + temperature = <145000>; > + hysteresis = <0>; > + type = "critical"; > + }; > + }; > + }; > + }; > +}; > + > +&spmi_bus { > + pmc8180_0: pmic@0 { > + compatible = "qcom,pm8150", "qcom,spmi-pmic"; > + reg = <0x0 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pon: power-on@800 { > + compatible = "qcom,pm8916-pon"; > + reg = <0x0800>; > + pwrkey { > + compatible = "qcom,pm8941-pwrkey"; > + interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; > + debounce = <15625>; > + bias-pull-up; > + linux,code = <KEY_POWER>; > + > + status = "disabled"; > + }; > + }; > + > + pmc8180_temp: temp-alarm@2400 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0x2400>; > + interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; > + io-channels = <&pmc8180_adc ADC5_DIE_TEMP>; > + io-channel-names = "thermal"; > + #thermal-sensor-cells = <0>; > + }; > + > + pmc8180_adc: adc@3100 { > + compatible = "qcom,spmi-adc5"; > + reg = <0x3100>; > + #address-cells = <1>; > + #size-cells = <0>; > + #io-channel-cells = <1>; > + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; > + > + ref-gnd@0 { > + reg = <ADC5_REF_GND>; > + qcom,pre-scaling = <1 1>; > + label = "ref_gnd"; > + }; > + > + vref-1p25@1 { > + reg = <ADC5_1P25VREF>; > + qcom,pre-scaling = <1 1>; > + label = "vref_1p25"; > + }; > + > + die-temp@6 { > + reg = <ADC5_DIE_TEMP>; > + qcom,pre-scaling = <1 1>; > + label = "die_temp"; > + }; > + }; > + > + pmc8180_adc_tm: adc-tm@3500 { > + compatible = "qcom,spmi-adc-tm5"; > + reg = <0x3500>; > + interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; > + #thermal-sensor-cells = <1>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + rtc@6000 { > + compatible = "qcom,pm8941-rtc"; > + reg = <0x6000>; > + reg-names = "rtc", "alarm"; > + interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; > + }; > + > + pmc8180_gpios: gpio@c000 { > + compatible = "qcom,pmc8180-gpio"; > + reg = <0xc000>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + }; > + > + pmic@1 { > + compatible = "qcom,pmc8180", "qcom,spmi-pmic"; > + reg = <0x1 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + pmic@2 { > + compatible = "qcom,smb2351", "qcom,spmi-pmic"; > + reg = <0x2 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + adc@3100 { > + compatible = "qcom,spmi-adc-rev2"; > + reg = <0x3100>; > + #address-cells = <1>; > + #size-cells = <0>; > + #io-channel-cells = <1>; > + interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; > + > + ref-gnd@0 { > + reg = <ADC5_REF_GND>; > + qcom,pre-scaling = <1 1>; > + label = "ref_gnd"; > + }; > + > + vref-1p25@1 { > + reg = <ADC5_1P25VREF>; > + qcom,pre-scaling = <1 1>; > + label = "vref_1p25"; > + }; > + > + vcoin@85 { > + reg = <0x85>; > + qcom,pre-scaling = <1 1>; > + label = "vcoin2"; > + }; > + }; > + }; > + > + pmic@6 { > + compatible = "qcom,pm8150c", "qcom,spmi-pmic"; > + reg = <0x6 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + pmic@8 { > + compatible = "qcom,pm8150", "qcom,spmi-pmic"; > + reg = <0x8 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + }; > + > + pmic@a { > + compatible = "qcom,smb2351", "qcom,spmi-pmic"; > + reg = <0xa SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + adc@3100 { > + compatible = "qcom,spmi-adc-rev2"; > + reg = <0x3100>; > + #address-cells = <1>; > + #size-cells = <0>; > + #io-channel-cells = <1>; > + interrupts = <0xa 0x31 0x0 IRQ_TYPE_EDGE_RISING>; > + > + ref-gnd@0 { > + reg = <ADC5_REF_GND>; > + qcom,pre-scaling = <1 1>; > + label = "ref_gnd"; > + }; > + > + vref-1p25@1 { > + reg = <ADC5_1P25VREF>; > + qcom,pre-scaling = <1 1>; > + label = "vref_1p25"; > + }; > + > + vcoin@85 { > + reg = <0x85>; > + qcom,pre-scaling = <1 1>; > + label = "vcoin"; > + }; > + }; > + }; > + > + pmic@4 { > + compatible = "qcom,pm8150c", "qcom,spmi-pmic"; > + reg = <0x4 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + power-on@800 { > + compatible = "qcom,pm8916-pon"; > + reg = <0x0800>; > + > + status = "disabled"; > + }; > + > + pmc8180c_temp: temp-alarm@2400 { > + compatible = "qcom,spmi-temp-alarm"; > + reg = <0x2400>; > + interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; > + io-channels = <&pmc8180c_adc ADC5_DIE_TEMP>; > + io-channel-names = "thermal"; > + #thermal-sensor-cells = <0>; > + }; > + > + pmc8180c_adc: adc@3100 { > + compatible = "qcom,spmi-adc5"; > + reg = <0x3100>; > + #address-cells = <1>; > + #size-cells = <0>; > + #io-channel-cells = <1>; > + interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; > + > + ref-gnd@0 { > + reg = <ADC5_REF_GND>; > + qcom,pre-scaling = <1 1>; > + label = "ref_gnd"; > + }; > + > + vref-1p25@1 { > + reg = <ADC5_1P25VREF>; > + qcom,pre-scaling = <1 1>; > + label = "vref_1p25"; > + }; > + > + die-temp@6 { > + reg = <ADC5_DIE_TEMP>; > + qcom,pre-scaling = <1 1>; > + label = "die_temp"; > + }; > + }; > + > + pmc8180c_adc_tm: adc-tm@3500 { > + compatible = "qcom,spmi-adc-tm5"; > + reg = <0x3500>; > + interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; > + #thermal-sensor-cells = <1>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + pmc8180c_gpios: gpio@c000 { > + compatible = "qcom,pmc8180c-gpio"; > + reg = <0xc000>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + }; > + > + pmic@5 { > + compatible = "qcom,pmc8180c", "qcom,spmi-pmic"; > + reg = <0x5 SPMI_USID>; > + > + pmc8180c_lpg: lpg { > + compatible = "qcom,pmc8180c-lpg"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + #pwm-cells = <2>; > + > + status = "disabled"; > + }; > + }; > +}; > diff --git a/arch/arm64/boot/dts/qcom/sc8180x-primus.dts b/arch/arm64/boot/dts/qcom/sc8180x-primus.dts > new file mode 100644 > index 000000000000..9f365fccae78 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sc8180x-primus.dts > @@ -0,0 +1,706 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. > + * Copyright (c) 2020-2023, Linaro Limited > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/gpio-keys.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> > +#include "sc8180x.dtsi" > +#include "sc8180x-pmics.dtsi" > + > +/ { > + model = "Qualcomm SC8180x Primus"; > + compatible = "qcom,sc8180x-primus", "qcom,sc8180x"; > + > + aliases { > + serial0 = &uart12; > + serial1 = &uart13; > + }; > + > + backlight: backlight { > + compatible = "pwm-backlight"; > + pwms = <&pmc8180c_lpg 4 1000000>; > + enable-gpios = <&pmc8180c_gpios 8 GPIO_ACTIVE_HIGH>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&bl_pwm_default>; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&hall_int_active_state>; > + > + lid-switch { > + gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>; > + linux,input-type = <EV_SW>; > + linux,code = <SW_LID>; > + wakeup-source; > + wakeup-event-action = <EV_ACT_DEASSERTED>; > + }; > + }; > + > + reserved-memory { > + rmtfs_mem: rmtfs-region@85500000 { > + compatible = "qcom,rmtfs-mem"; > + reg = <0x0 0x85500000 0x0 0x200000>; > + no-map; > + > + qcom,client-id = <1>; > + qcom,vmid = <15>; > + }; > + > + wlan_mem: wlan-region@8bc00000 { > + reg = <0x0 0x8bc00000 0x0 0x180000>; > + no-map; > + }; > + > + adsp_mem: adsp-region@96e00000 { > + reg = <0x0 0x96e00000 0x0 0x1c00000>; > + no-map; > + }; > + > + mpss_mem: mpss-region@8d800000 { > + reg = <0x0 0x8d800000 0x0 0x9600000>; > + no-map; > + }; > + > + gpu_mem: gpu-region@98a00000 { > + reg = <0x0 0x98a00000 0x0 0x2000>; > + no-map; > + }; > + > + reserved-region@9a500000 { > + reg = <0x0 0x9a500000 0x0 0x600000>; > + no-map; > + }; > + }; > + > + vreg_nvme_0p9: nvme-0p9-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vreg_nvme_0p9"; > + > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <900000>; > + > + regulator-always-on; > + }; > + > + vreg_nvme_3p3: nvme-3p3-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vreg_nvme_3p3"; > + > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + > + gpio = <&pmc8180c_gpios 11 0>; > + enable-active-high; > + > + regulator-always-on; > + }; > + > + vdd_kb_tp_3v3: vdd-kb-tp-3v3-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vdd_kb_tp_3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + > + gpio = <&tlmm 4 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + > + regulator-always-on; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&kb_tp_3v3_en_active_state>; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vph_pwr"; > + regulator-min-microvolt = <3700000>; > + regulator-max-microvolt = <3700000>; > + }; > + > + vreg_s4a_1p8: pm8150-s4 { > + compatible = "regulator-fixed"; > + regulator-name = "vreg_s4a_1p8"; > + > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + > + regulator-always-on; > + regulator-boot-on; > + > + vin-supply = <&vph_pwr>; > + }; > +}; > + > +&apps_rsc { > + pmc8180-a-rpmh-regulators { > + compatible = "qcom,pmc8180-rpmh-regulators"; > + qcom,pmic-id = "a"; > + > + vdd-s5-supply = <&vph_pwr>; > + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>; > + > + vreg_s5a_2p0: smps5 { > + regulator-min-microvolt = <2040000>; > + regulator-max-microvolt = <2100000>; > + }; > + > + vreg_l7a_1p8: ldo7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9a_1p3: ldo9 { > + regulator-min-microvolt = <1296000>; > + regulator-max-microvolt = <1304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l12a_1p8: ldo12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + pmc8180c-rpmh-regulators { > + compatible = "qcom,pmc8180c-rpmh-regulators"; > + qcom,pmic-id = "c"; > + > + vdd-s6-supply = <&vph_pwr>; > + vdd-s8-supply = <&vph_pwr>; > + vdd-l2-l3-supply = <&vreg_s6c_1p35>; > + vdd-bob-supply = <&vph_pwr>; > + > + vreg_s6c_1p35: smps6 { > + regulator-min-microvolt = <1350000>; > + regulator-max-microvolt = <1372000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s8c_1p8: smps8 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-always-on; > + }; > + > + vreg_l3c_1p2: ldo3 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l4c_3p3: ldo4 { > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l10c_3p3: ldo10 { > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3312000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l11c_3p3: ldo11 { > + regulator-min-microvolt = <3296000>; > + regulator-max-microvolt = <3304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_bob: bob { > + regulator-min-microvolt = <3296000>; > + regulator-max-microvolt = <3350000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + pmc8180-e-rpmh-regulators { > + compatible = "qcom,pmc8180-rpmh-regulators"; > + qcom,pmic-id = "e"; > + > + vdd-s4-supply = <&vph_pwr>; > + vdd-s5-supply = <&vph_pwr>; > + vdd-l2-l10-supply = <&vreg_bob>; > + vdd-l3-l4-l5-l18-supply = <&vreg_s4e_0p98>; > + vdd-l7-l12-l14-l15-supply = <&vreg_s5e_2p05>; > + vdd-l13-l16-l17-supply = <&vreg_bob>; > + > + vreg_s4e_0p98: smps4 { > + regulator-min-microvolt = <992000>; > + regulator-max-microvolt = <992000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s5e_2p05: smps5 { > + regulator-min-microvolt = <2040000>; > + regulator-max-microvolt = <2040000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l1e_0p75: ldo1 { > + regulator-min-microvolt = <752000>; > + regulator-max-microvolt = <752000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l5e_0p88: ldo5 { > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <880000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7e_1p8: ldo7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l10e_2p9: ldo10 { > + regulator-min-microvolt = <2904000>; > + regulator-max-microvolt = <2904000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l12e: ldo12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l16e_3p0: ldo16 { > + regulator-min-microvolt = <3072000>; > + regulator-max-microvolt = <3072000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > +}; > + > +&dispcc { > + status = "okay"; > +}; > + > +&gpu { > + status = "okay"; > + > + zap-shader { > + memory-region = <&gpu_mem>; > + firmware-name = "qcom/sc8180x/qcdxkmsuc8180.mbn"; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <100000>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&ts_i2c_active_state>; > + > + status = "okay"; > + > + touchscreen@10 { > + compatible = "hid-over-i2c"; > + reg = <0x10>; > + hid-descr-addr = <0x1>; > + > + vdd-supply = <&vreg_l4c_3p3>; > + vddl-supply = <&vreg_l12e>; > + > + post-power-on-delay-ms = <20>; > + > + interrupts-extended = <&tlmm 122 IRQ_TYPE_LEVEL_LOW>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&ts_active_state>; > + }; > +}; > + > +&i2c7 { > + clock-frequency = <100000>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&aux_i2c_active_state>; > + > + status = "okay"; > + > + touchpad@15 { > + compatible = "hid-over-i2c"; > + reg = <0x15>; > + hid-descr-addr = <0x1>; > + > + interrupts-extended = <&tlmm 24 IRQ_TYPE_LEVEL_LOW>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&tp_int_active_state>; > + > + vdd-supply = <&vdd_kb_tp_3v3>; > + }; > + > + keyboard@3a { > + compatible = "hid-over-i2c"; > + reg = <0x3a>; > + hid-descr-addr = <0x1>; > + interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_LOW>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&kb_int_active_state>; > + > + vdd-supply = <&vdd_kb_tp_3v3>; > + }; > +}; > + > +&mdss { > + status = "okay"; > +}; > + > +&mdss_edp { > + data-lanes = <0 1 2 3>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&edp_hpd_active>; > + > + status = "okay"; > + > + aux-bus { > + panel { > + compatible = "edp-panel"; > + > + backlight = <&backlight>; > + > + ports { > + port { > + auo_b133han05_in: endpoint { > + remote-endpoint = <&mdss_edp_out>; > + }; > + }; > + }; > + }; > + }; > + > + ports { > + port@1 { > + reg = <1>; > + mdss_edp_out: endpoint { > + remote-endpoint = <&auo_b133han05_in>; > + }; > + }; > + }; > +}; > + > +&pcie1 { > + perst-gpio = <&tlmm 175 GPIO_ACTIVE_LOW>; > + wake-gpio = <&tlmm 177 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pcie2_default_state>; > + > + status = "okay"; > +}; > + > +&pcie1_phy { > + vdda-phy-supply = <&vreg_l5e_0p88>; > + vdda-pll-supply = <&vreg_l3c_1p2>; > + > + status = "okay"; > +}; > + > +&pmc8180c_lpg { > + status = "okay"; > +}; > + > +&qupv3_id_0 { > + status = "okay"; > +}; > + > +&qupv3_id_1 { > + status = "okay"; > +}; > + > +&qupv3_id_2 { > + status = "okay"; > +}; > + > +&remoteproc_adsp { > + memory-region = <&adsp_mem>; > + firmware-name = "qcom/sc8180x/qcadsp8180.mbn"; > + > + status = "okay"; > +}; > + > +&remoteproc_mpss { > + memory-region = <&mpss_mem>; > + firmware-name = "qcom/sc8180x/qcmpss8180.mbn"; > + > + status = "okay"; > +}; > + > +&uart12 { > + compatible = "qcom,geni-debug-uart"; > + status = "okay"; > +}; > + > +&uart13 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart13_state>; > + > + status = "okay"; > + > + bluetooth { > + compatible = "qcom,wcn3998-bt"; > + > + vddio-supply = <&vreg_s4a_1p8>; > + vddxo-supply = <&vreg_l7a_1p8>; > + vddrf-supply = <&vreg_l9a_1p3>; > + vddch0-supply = <&vreg_l11c_3p3>; > + max-speed = <3200000>; > + }; > +}; > + > +&ufs_mem_hc { > + reset-gpios = <&tlmm 190 GPIO_ACTIVE_LOW>; > + > + vcc-supply = <&vreg_l10e_2p9>; > + vcc-max-microamp = <155000>; > + > + vccq2-supply = <&vreg_l7e_1p8>; > + vccq2-max-microamp = <425000>; > + > + status = "okay"; > +}; > + > +&ufs_mem_phy { > + vdda-phy-supply = <&vreg_l5e_0p88>; > + vdda-pll-supply = <&vreg_l3c_1p2>; > + > + status = "okay"; > +}; > + > +&usb_prim_hsphy { > + vdda-pll-supply = <&vreg_l5e_0p88>; > + vdda18-supply = <&vreg_l12a_1p8>; > + vdda33-supply = <&vreg_l16e_3p0>; > + > + status = "okay"; > +}; > + > +&usb_prim_qmpphy { > + vdda-phy-supply = <&vreg_l3c_1p2>; > + vdda-pll-supply = <&vreg_l5e_0p88>; > + > + status = "okay"; > +}; > + > +&usb_prim { > + status = "okay"; > +}; > + > +&usb_prim_dwc3 { > + dr_mode = "host"; > +}; > + > +&usb_sec_hsphy { > + vdda-pll-supply = <&vreg_l5e_0p88>; > + vdda18-supply = <&vreg_l12a_1p8>; > + vdda33-supply = <&vreg_l16e_3p0>; > + > + status = "okay"; > +}; > + > +&usb_sec_qmpphy { > + vdda-phy-supply = <&vreg_l3c_1p2>; > + vdda-pll-supply = <&vreg_l5e_0p88>; > + > + status = "okay"; > +}; > + > +&usb_sec { > + status = "okay"; > +}; > + > +&usb_sec_dwc3 { > + dr_mode = "host"; > +}; > + > +&wifi { > + memory-region = <&wlan_mem>; > + > + vdd-0.8-cx-mx-supply = <&vreg_l1e_0p75>; > + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; > + vdd-1.3-rfa-supply = <&vreg_l9a_1p3>; > + vdd-3.3-ch0-supply = <&vreg_l11c_3p3>; > + vdd-3.3-ch1-supply = <&vreg_l10c_3p3>; > + > + status = "okay"; > +}; > + > +&xo_board_clk { > + clock-frequency = <38400000>; > +}; > + > +/* PINCTRL */ > + > +&pmc8180c_gpios { > + bl_pwm_default: bl-pwm-default-state { > + en-pins { > + pins = "gpio8"; > + function = "normal"; > + }; > + > + pwm-pins { > + pins = "gpio10"; > + function = "func1"; > + }; > + }; > +}; > + > +&tlmm { > + gpio-reserved-ranges = <0 4>, <47 4>, <126 4>; > + > + aux_i2c_active_state: aux-i2c-active-state { > + pins = "gpio98", "gpio99"; > + function = "qup7"; > + > + bias-disable; > + drive-strength = <16>; > + }; > + > + edp_hpd_active: epd-hpd-active-state { > + pins = "gpio10"; > + function = "edp_hot"; > + }; > + > + hall_int_active_state: hall-int-active-state { > + pins = "gpio121"; > + function = "gpio"; > + > + input-enable; > + bias-disable; > + }; > + > + kb_int_active_state: kb-int-active-state { > + int-n-pins { > + pins = "gpio37"; > + function = "gpio"; > + > + bias-pull-up; > + intput-enable; > + }; > + > + kp-disable-pins { > + pins = "gpio135"; > + function = "gpio"; > + > + output-high; > + }; > + }; > + > + kb_tp_3v3_en_active_state: kb-tp-3v3-en-active-state { > + pins = "gpio4"; > + functino = "gpio"; > + > + bias-disable; > + }; > + > + pcie2_default_state: pcie2-default-state { > + clkreq-pins { > + pins = "gpio176"; > + function = "pci_e2"; > + bias-pull-up; > + }; > + > + reset-n-pins { > + pins = "gpio175"; > + function = "gpio"; > + > + drive-strength = <2>; > + output-low; > + bias-pull-down; > + }; > + > + wake-n-pins { > + pins = "gpio177"; > + function = "gpio"; > + > + drive-strength = <2>; > + bias-pull-up; > + }; > + }; > + > + tp_int_active_state: tp-int-active-state { > + tp-int-pins { > + pins = "gpio24"; > + function = "gpio"; > + > + bias-disable; > + input-enable; > + }; > + > + tp-close-n-pins { > + pins = "gpio116"; > + function = "gpio"; > + > + bias-disable; > + input-enable; > + }; > + }; > + > + ts_active_state: ts-active-state { > + int-n-pins { > + pins = "gpio122"; > + function = "gpio"; > + > + input-enable; > + bias-disable; > + }; > + > + reset-n-pins { > + pins = "gpio54"; > + function = "gpio"; > + > + output-high; > + }; > + }; > + > + ts_i2c_active_state: ts-i2c-active-state { > + pins = "gpio114", "gpio115"; > + function = "qup1"; > + > + /* External pull up */ > + bias-disable; > + drive-strength = <2>; > + }; > + > + uart13_state: uart13-state { > + cts-pins { > + pins = "gpio43"; > + function = "qup13"; > + bias-pull-down; > + }; > + > + rts-tx-pins { > + pins = "gpio44", "gpio45"; > + function = "qup13"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + rx-pins { > + pins = "gpio46"; > + function = "qup13"; > + bias-pull-up; > + }; > + }; > +};
On 25-03-23, 13:36, Konrad Dybcio wrote: > > > On 25.03.2023 13:24, Vinod Koul wrote: > > From: Bjorn Andersson <bjorn.andersson@linaro.org> > > > > Introduce support for the SC8180X reference device, aka Primus, with > > debug UART, regulators, UFS and USB support. > > > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > > --- > Please introduce PMICs in a separate commit. On top of that, > the previous patch (in a very slim and basic version) should > have been combined with (a very slim and basic version) this > patch so that we don't introduce code that never compiles. > > And the patches are missing your (as the sender) S-o-bs. Yeah not sure how that got missed, thanks for checking
On 25/03/2023 13:24, Vinod Koul wrote: > From: Bjorn Andersson <bjorn.andersson@linaro.org> > > Introduce support for the SC8180X reference device, aka Primus, with > debug UART, regulators, UFS and USB support. > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi | 326 +++++++++ > arch/arm64/boot/dts/qcom/sc8180x-primus.dts | 706 ++++++++++++++++++++ > 3 files changed, 1033 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi > create mode 100644 arch/arm64/boot/dts/qcom/sc8180x-primus.dts > (...) > diff --git a/arch/arm64/boot/dts/qcom/sc8180x-primus.dts b/arch/arm64/boot/dts/qcom/sc8180x-primus.dts > new file mode 100644 > index 000000000000..9f365fccae78 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/sc8180x-primus.dts > @@ -0,0 +1,706 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. > + * Copyright (c) 2020-2023, Linaro Limited > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/gpio-keys.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> > +#include "sc8180x.dtsi" > +#include "sc8180x-pmics.dtsi" > + > +/ { > + model = "Qualcomm SC8180x Primus"; > + compatible = "qcom,sc8180x-primus", "qcom,sc8180x"; Please run scripts/checkpatch.pl and fix reported warnings. > + > + aliases { > + serial0 = &uart12; > + serial1 = &uart13; > + }; > + > + backlight: backlight { > + compatible = "pwm-backlight"; > + pwms = <&pmc8180c_lpg 4 1000000>; > + enable-gpios = <&pmc8180c_gpios 8 GPIO_ACTIVE_HIGH>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&bl_pwm_default>; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&hall_int_active_state>; > + > + lid-switch { > + gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>; > + linux,input-type = <EV_SW>; > + linux,code = <SW_LID>; > + wakeup-source; > + wakeup-event-action = <EV_ACT_DEASSERTED>; > + }; > + }; > + > + reserved-memory { > + rmtfs_mem: rmtfs-region@85500000 { > + compatible = "qcom,rmtfs-mem"; > + reg = <0x0 0x85500000 0x0 0x200000>; > + no-map; > + > + qcom,client-id = <1>; > + qcom,vmid = <15>; > + }; > + > + wlan_mem: wlan-region@8bc00000 { > + reg = <0x0 0x8bc00000 0x0 0x180000>; > + no-map; > + }; > + > + adsp_mem: adsp-region@96e00000 { > + reg = <0x0 0x96e00000 0x0 0x1c00000>; > + no-map; > + }; > + > + mpss_mem: mpss-region@8d800000 { > + reg = <0x0 0x8d800000 0x0 0x9600000>; > + no-map; > + }; > + > + gpu_mem: gpu-region@98a00000 { > + reg = <0x0 0x98a00000 0x0 0x2000>; > + no-map; > + }; > + > + reserved-region@9a500000 { > + reg = <0x0 0x9a500000 0x0 0x600000>; > + no-map; > + }; > + }; > + > + vreg_nvme_0p9: nvme-0p9-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vreg_nvme_0p9"; > + > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <900000>; > + > + regulator-always-on; > + }; > + > + vreg_nvme_3p3: nvme-3p3-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vreg_nvme_3p3"; > + > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + > + gpio = <&pmc8180c_gpios 11 0>; > + enable-active-high; > + > + regulator-always-on; > + }; > + > + vdd_kb_tp_3v3: vdd-kb-tp-3v3-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vdd_kb_tp_3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + > + gpio = <&tlmm 4 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + > + regulator-always-on; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&kb_tp_3v3_en_active_state>; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vph_pwr"; > + regulator-min-microvolt = <3700000>; > + regulator-max-microvolt = <3700000>; > + }; > + > + vreg_s4a_1p8: pm8150-s4 { -regulator suffix > + compatible = "regulator-fixed"; > + regulator-name = "vreg_s4a_1p8"; > + > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + > + regulator-always-on; > + regulator-boot-on; > + > + vin-supply = <&vph_pwr>; > + }; > +}; > + > +&apps_rsc { > + pmc8180-a-rpmh-regulators { Does not look like you tested the DTS against bindings. Please run `make dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst for instructions). > + compatible = "qcom,pmc8180-rpmh-regulators"; > + qcom,pmic-id = "a"; > + > + vdd-s5-supply = <&vph_pwr>; > + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>; > + > + vreg_s5a_2p0: smps5 { > + regulator-min-microvolt = <2040000>; > + regulator-max-microvolt = <2100000>; > + }; > + > + vreg_l7a_1p8: ldo7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9a_1p3: ldo9 { > + regulator-min-microvolt = <1296000>; > + regulator-max-microvolt = <1304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l12a_1p8: ldo12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + pmc8180c-rpmh-regulators { > + compatible = "qcom,pmc8180c-rpmh-regulators"; > + qcom,pmic-id = "c"; > + > + vdd-s6-supply = <&vph_pwr>; > + vdd-s8-supply = <&vph_pwr>; > + vdd-l2-l3-supply = <&vreg_s6c_1p35>; > + vdd-bob-supply = <&vph_pwr>; > + > + vreg_s6c_1p35: smps6 { > + regulator-min-microvolt = <1350000>; > + regulator-max-microvolt = <1372000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s8c_1p8: smps8 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + regulator-always-on; > + }; > + > + vreg_l3c_1p2: ldo3 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l4c_3p3: ldo4 { > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3008000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l10c_3p3: ldo10 { > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3312000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l11c_3p3: ldo11 { > + regulator-min-microvolt = <3296000>; > + regulator-max-microvolt = <3304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_bob: bob { > + regulator-min-microvolt = <3296000>; > + regulator-max-microvolt = <3350000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + pmc8180-e-rpmh-regulators { > + compatible = "qcom,pmc8180-rpmh-regulators"; > + qcom,pmic-id = "e"; > + > + vdd-s4-supply = <&vph_pwr>; > + vdd-s5-supply = <&vph_pwr>; > + vdd-l2-l10-supply = <&vreg_bob>; > + vdd-l3-l4-l5-l18-supply = <&vreg_s4e_0p98>; > + vdd-l7-l12-l14-l15-supply = <&vreg_s5e_2p05>; > + vdd-l13-l16-l17-supply = <&vreg_bob>; > + > + vreg_s4e_0p98: smps4 { > + regulator-min-microvolt = <992000>; > + regulator-max-microvolt = <992000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s5e_2p05: smps5 { > + regulator-min-microvolt = <2040000>; > + regulator-max-microvolt = <2040000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l1e_0p75: ldo1 { > + regulator-min-microvolt = <752000>; > + regulator-max-microvolt = <752000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l5e_0p88: ldo5 { > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <880000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7e_1p8: ldo7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l10e_2p9: ldo10 { > + regulator-min-microvolt = <2904000>; > + regulator-max-microvolt = <2904000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l12e: ldo12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l16e_3p0: ldo16 { > + regulator-min-microvolt = <3072000>; > + regulator-max-microvolt = <3072000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > +}; > + > +&dispcc { > + status = "okay"; > +}; > + > +&gpu { > + status = "okay"; > + > + zap-shader { > + memory-region = <&gpu_mem>; > + firmware-name = "qcom/sc8180x/qcdxkmsuc8180.mbn"; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <100000>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&ts_i2c_active_state>; > + > + status = "okay"; > + > + touchscreen@10 { > + compatible = "hid-over-i2c"; > + reg = <0x10>; > + hid-descr-addr = <0x1>; > + > + vdd-supply = <&vreg_l4c_3p3>; > + vddl-supply = <&vreg_l12e>; > + > + post-power-on-delay-ms = <20>; > + > + interrupts-extended = <&tlmm 122 IRQ_TYPE_LEVEL_LOW>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&ts_active_state>; > + }; > +}; > + > +&i2c7 { > + clock-frequency = <100000>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&aux_i2c_active_state>; > + > + status = "okay"; > + > + touchpad@15 { > + compatible = "hid-over-i2c"; > + reg = <0x15>; > + hid-descr-addr = <0x1>; > + > + interrupts-extended = <&tlmm 24 IRQ_TYPE_LEVEL_LOW>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&tp_int_active_state>; > + > + vdd-supply = <&vdd_kb_tp_3v3>; > + }; > + > + keyboard@3a { > + compatible = "hid-over-i2c"; > + reg = <0x3a>; > + hid-descr-addr = <0x1>; > + interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_LOW>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&kb_int_active_state>; > + > + vdd-supply = <&vdd_kb_tp_3v3>; > + }; > +}; > + > +&mdss { > + status = "okay"; > +}; > + > +&mdss_edp { > + data-lanes = <0 1 2 3>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&edp_hpd_active>; > + > + status = "okay"; > + > + aux-bus { > + panel { > + compatible = "edp-panel"; > + > + backlight = <&backlight>; > + > + ports { Are you sure this passes dtbs checks? Best regards, Krzysztof
On 27/03/2023 10:12, Krzysztof Kozlowski wrote: >> + >> +/ { >> + model = "Qualcomm SC8180x Primus"; >> + compatible = "qcom,sc8180x-primus", "qcom,sc8180x"; > > Please run scripts/checkpatch.pl and fix reported warnings. It seems it is already documented. Confusing to document board compatibles in separate patchset one year before boards gets accepted... Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 31aa54f0428c..fdce44a7a902 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -141,6 +141,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-zombie-nvme-lte.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp2.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc8180x-primus.dtb dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-lenovo-thinkpad-x13s.dtb dtb-$(CONFIG_ARCH_QCOM) += sda660-inforce-ifc6560.dtb diff --git a/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi b/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi new file mode 100644 index 000000000000..49c146b6f37f --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi @@ -0,0 +1,326 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. + * Copyright (c) 2021-2022, Linaro Limited + */ + +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/spmi/spmi.h> +#include <dt-bindings/iio/qcom,spmi-vadc.h> + +/ { + thermal-zones { + pmc8180-thermal { + polling-delay-passive = <100>; + polling-delay = <0>; + + thermal-sensors = <&pmc8180_temp>; + + trips { + trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + + trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + + pmc8180c-thermal { + polling-delay-passive = <100>; + polling-delay = <0>; + + thermal-sensors = <&pmc8180c_temp>; + + trips { + trip0 { + temperature = <95000>; + hysteresis = <0>; + type = "passive"; + }; + + trip1 { + temperature = <115000>; + hysteresis = <0>; + type = "hot"; + }; + + trip2 { + temperature = <145000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + }; +}; + +&spmi_bus { + pmc8180_0: pmic@0 { + compatible = "qcom,pm8150", "qcom,spmi-pmic"; + reg = <0x0 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pon: power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + pwrkey { + compatible = "qcom,pm8941-pwrkey"; + interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_POWER>; + + status = "disabled"; + }; + }; + + pmc8180_temp: temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; + io-channels = <&pmc8180_adc ADC5_DIE_TEMP>; + io-channel-names = "thermal"; + #thermal-sensor-cells = <0>; + }; + + pmc8180_adc: adc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + die-temp@6 { + reg = <ADC5_DIE_TEMP>; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + }; + + pmc8180_adc_tm: adc-tm@3500 { + compatible = "qcom,spmi-adc-tm5"; + reg = <0x3500>; + interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; + #thermal-sensor-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + rtc@6000 { + compatible = "qcom,pm8941-rtc"; + reg = <0x6000>; + reg-names = "rtc", "alarm"; + interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; + }; + + pmc8180_gpios: gpio@c000 { + compatible = "qcom,pmc8180-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pmic@1 { + compatible = "qcom,pmc8180", "qcom,spmi-pmic"; + reg = <0x1 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; + + pmic@2 { + compatible = "qcom,smb2351", "qcom,spmi-pmic"; + reg = <0x2 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + adc@3100 { + compatible = "qcom,spmi-adc-rev2"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + vcoin@85 { + reg = <0x85>; + qcom,pre-scaling = <1 1>; + label = "vcoin2"; + }; + }; + }; + + pmic@6 { + compatible = "qcom,pm8150c", "qcom,spmi-pmic"; + reg = <0x6 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; + + pmic@8 { + compatible = "qcom,pm8150", "qcom,spmi-pmic"; + reg = <0x8 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; + + pmic@a { + compatible = "qcom,smb2351", "qcom,spmi-pmic"; + reg = <0xa SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + adc@3100 { + compatible = "qcom,spmi-adc-rev2"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0xa 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + vcoin@85 { + reg = <0x85>; + qcom,pre-scaling = <1 1>; + label = "vcoin"; + }; + }; + }; + + pmic@4 { + compatible = "qcom,pm8150c", "qcom,spmi-pmic"; + reg = <0x4 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + + status = "disabled"; + }; + + pmc8180c_temp: temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; + io-channels = <&pmc8180c_adc ADC5_DIE_TEMP>; + io-channel-names = "thermal"; + #thermal-sensor-cells = <0>; + }; + + pmc8180c_adc: adc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + ref-gnd@0 { + reg = <ADC5_REF_GND>; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = <ADC5_1P25VREF>; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + die-temp@6 { + reg = <ADC5_DIE_TEMP>; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + }; + + pmc8180c_adc_tm: adc-tm@3500 { + compatible = "qcom,spmi-adc-tm5"; + reg = <0x3500>; + interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; + #thermal-sensor-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + pmc8180c_gpios: gpio@c000 { + compatible = "qcom,pmc8180c-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pmic@5 { + compatible = "qcom,pmc8180c", "qcom,spmi-pmic"; + reg = <0x5 SPMI_USID>; + + pmc8180c_lpg: lpg { + compatible = "qcom,pmc8180c-lpg"; + + #address-cells = <1>; + #size-cells = <0>; + #pwm-cells = <2>; + + status = "disabled"; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/sc8180x-primus.dts b/arch/arm64/boot/dts/qcom/sc8180x-primus.dts new file mode 100644 index 000000000000..9f365fccae78 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc8180x-primus.dts @@ -0,0 +1,706 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. + * Copyright (c) 2020-2023, Linaro Limited + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/gpio-keys.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "sc8180x.dtsi" +#include "sc8180x-pmics.dtsi" + +/ { + model = "Qualcomm SC8180x Primus"; + compatible = "qcom,sc8180x-primus", "qcom,sc8180x"; + + aliases { + serial0 = &uart12; + serial1 = &uart13; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pmc8180c_lpg 4 1000000>; + enable-gpios = <&pmc8180c_gpios 8 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&bl_pwm_default>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&hall_int_active_state>; + + lid-switch { + gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + wakeup-source; + wakeup-event-action = <EV_ACT_DEASSERTED>; + }; + }; + + reserved-memory { + rmtfs_mem: rmtfs-region@85500000 { + compatible = "qcom,rmtfs-mem"; + reg = <0x0 0x85500000 0x0 0x200000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <15>; + }; + + wlan_mem: wlan-region@8bc00000 { + reg = <0x0 0x8bc00000 0x0 0x180000>; + no-map; + }; + + adsp_mem: adsp-region@96e00000 { + reg = <0x0 0x96e00000 0x0 0x1c00000>; + no-map; + }; + + mpss_mem: mpss-region@8d800000 { + reg = <0x0 0x8d800000 0x0 0x9600000>; + no-map; + }; + + gpu_mem: gpu-region@98a00000 { + reg = <0x0 0x98a00000 0x0 0x2000>; + no-map; + }; + + reserved-region@9a500000 { + reg = <0x0 0x9a500000 0x0 0x600000>; + no-map; + }; + }; + + vreg_nvme_0p9: nvme-0p9-regulator { + compatible = "regulator-fixed"; + regulator-name = "vreg_nvme_0p9"; + + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + + regulator-always-on; + }; + + vreg_nvme_3p3: nvme-3p3-regulator { + compatible = "regulator-fixed"; + regulator-name = "vreg_nvme_3p3"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&pmc8180c_gpios 11 0>; + enable-active-high; + + regulator-always-on; + }; + + vdd_kb_tp_3v3: vdd-kb-tp-3v3-regulator { + compatible = "regulator-fixed"; + regulator-name = "vdd_kb_tp_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + + regulator-always-on; + + pinctrl-names = "default"; + pinctrl-0 = <&kb_tp_3v3_en_active_state>; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + vreg_s4a_1p8: pm8150-s4 { + compatible = "regulator-fixed"; + regulator-name = "vreg_s4a_1p8"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; +}; + +&apps_rsc { + pmc8180-a-rpmh-regulators { + compatible = "qcom,pmc8180-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s5-supply = <&vph_pwr>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p0>; + + vreg_s5a_2p0: smps5 { + regulator-min-microvolt = <2040000>; + regulator-max-microvolt = <2100000>; + }; + + vreg_l7a_1p8: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9a_1p3: ldo9 { + regulator-min-microvolt = <1296000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12a_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pmc8180c-rpmh-regulators { + compatible = "qcom,pmc8180c-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s6-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-l2-l3-supply = <&vreg_s6c_1p35>; + vdd-bob-supply = <&vph_pwr>; + + vreg_s6c_1p35: smps6 { + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1372000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s8c_1p8: smps8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-always-on; + }; + + vreg_l3c_1p2: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4c_3p3: ldo4 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10c_3p3: ldo10 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11c_3p3: ldo11 { + regulator-min-microvolt = <3296000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob: bob { + regulator-min-microvolt = <3296000>; + regulator-max-microvolt = <3350000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pmc8180-e-rpmh-regulators { + compatible = "qcom,pmc8180-rpmh-regulators"; + qcom,pmic-id = "e"; + + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-l2-l10-supply = <&vreg_bob>; + vdd-l3-l4-l5-l18-supply = <&vreg_s4e_0p98>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5e_2p05>; + vdd-l13-l16-l17-supply = <&vreg_bob>; + + vreg_s4e_0p98: smps4 { + regulator-min-microvolt = <992000>; + regulator-max-microvolt = <992000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s5e_2p05: smps5 { + regulator-min-microvolt = <2040000>; + regulator-max-microvolt = <2040000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1e_0p75: ldo1 { + regulator-min-microvolt = <752000>; + regulator-max-microvolt = <752000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5e_0p88: ldo5 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7e_1p8: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10e_2p9: ldo10 { + regulator-min-microvolt = <2904000>; + regulator-max-microvolt = <2904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12e: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16e_3p0: ldo16 { + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; +}; + +&dispcc { + status = "okay"; +}; + +&gpu { + status = "okay"; + + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sc8180x/qcdxkmsuc8180.mbn"; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts_i2c_active_state>; + + status = "okay"; + + touchscreen@10 { + compatible = "hid-over-i2c"; + reg = <0x10>; + hid-descr-addr = <0x1>; + + vdd-supply = <&vreg_l4c_3p3>; + vddl-supply = <&vreg_l12e>; + + post-power-on-delay-ms = <20>; + + interrupts-extended = <&tlmm 122 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts_active_state>; + }; +}; + +&i2c7 { + clock-frequency = <100000>; + + pinctrl-names = "default"; + pinctrl-0 = <&aux_i2c_active_state>; + + status = "okay"; + + touchpad@15 { + compatible = "hid-over-i2c"; + reg = <0x15>; + hid-descr-addr = <0x1>; + + interrupts-extended = <&tlmm 24 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&tp_int_active_state>; + + vdd-supply = <&vdd_kb_tp_3v3>; + }; + + keyboard@3a { + compatible = "hid-over-i2c"; + reg = <0x3a>; + hid-descr-addr = <0x1>; + interrupts-extended = <&tlmm 37 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&kb_int_active_state>; + + vdd-supply = <&vdd_kb_tp_3v3>; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_edp { + data-lanes = <0 1 2 3>; + + pinctrl-names = "default"; + pinctrl-0 = <&edp_hpd_active>; + + status = "okay"; + + aux-bus { + panel { + compatible = "edp-panel"; + + backlight = <&backlight>; + + ports { + port { + auo_b133han05_in: endpoint { + remote-endpoint = <&mdss_edp_out>; + }; + }; + }; + }; + }; + + ports { + port@1 { + reg = <1>; + mdss_edp_out: endpoint { + remote-endpoint = <&auo_b133han05_in>; + }; + }; + }; +}; + +&pcie1 { + perst-gpio = <&tlmm 175 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 177 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie2_default_state>; + + status = "okay"; +}; + +&pcie1_phy { + vdda-phy-supply = <&vreg_l5e_0p88>; + vdda-pll-supply = <&vreg_l3c_1p2>; + + status = "okay"; +}; + +&pmc8180c_lpg { + status = "okay"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&qupv3_id_2 { + status = "okay"; +}; + +&remoteproc_adsp { + memory-region = <&adsp_mem>; + firmware-name = "qcom/sc8180x/qcadsp8180.mbn"; + + status = "okay"; +}; + +&remoteproc_mpss { + memory-region = <&mpss_mem>; + firmware-name = "qcom/sc8180x/qcmpss8180.mbn"; + + status = "okay"; +}; + +&uart12 { + compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; + +&uart13 { + pinctrl-names = "default"; + pinctrl-0 = <&uart13_state>; + + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3998-bt"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l9a_1p3>; + vddch0-supply = <&vreg_l11c_3p3>; + max-speed = <3200000>; + }; +}; + +&ufs_mem_hc { + reset-gpios = <&tlmm 190 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l10e_2p9>; + vcc-max-microamp = <155000>; + + vccq2-supply = <&vreg_l7e_1p8>; + vccq2-max-microamp = <425000>; + + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&vreg_l5e_0p88>; + vdda-pll-supply = <&vreg_l3c_1p2>; + + status = "okay"; +}; + +&usb_prim_hsphy { + vdda-pll-supply = <&vreg_l5e_0p88>; + vdda18-supply = <&vreg_l12a_1p8>; + vdda33-supply = <&vreg_l16e_3p0>; + + status = "okay"; +}; + +&usb_prim_qmpphy { + vdda-phy-supply = <&vreg_l3c_1p2>; + vdda-pll-supply = <&vreg_l5e_0p88>; + + status = "okay"; +}; + +&usb_prim { + status = "okay"; +}; + +&usb_prim_dwc3 { + dr_mode = "host"; +}; + +&usb_sec_hsphy { + vdda-pll-supply = <&vreg_l5e_0p88>; + vdda18-supply = <&vreg_l12a_1p8>; + vdda33-supply = <&vreg_l16e_3p0>; + + status = "okay"; +}; + +&usb_sec_qmpphy { + vdda-phy-supply = <&vreg_l3c_1p2>; + vdda-pll-supply = <&vreg_l5e_0p88>; + + status = "okay"; +}; + +&usb_sec { + status = "okay"; +}; + +&usb_sec_dwc3 { + dr_mode = "host"; +}; + +&wifi { + memory-region = <&wlan_mem>; + + vdd-0.8-cx-mx-supply = <&vreg_l1e_0p75>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l9a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l11c_3p3>; + vdd-3.3-ch1-supply = <&vreg_l10c_3p3>; + + status = "okay"; +}; + +&xo_board_clk { + clock-frequency = <38400000>; +}; + +/* PINCTRL */ + +&pmc8180c_gpios { + bl_pwm_default: bl-pwm-default-state { + en-pins { + pins = "gpio8"; + function = "normal"; + }; + + pwm-pins { + pins = "gpio10"; + function = "func1"; + }; + }; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <47 4>, <126 4>; + + aux_i2c_active_state: aux-i2c-active-state { + pins = "gpio98", "gpio99"; + function = "qup7"; + + bias-disable; + drive-strength = <16>; + }; + + edp_hpd_active: epd-hpd-active-state { + pins = "gpio10"; + function = "edp_hot"; + }; + + hall_int_active_state: hall-int-active-state { + pins = "gpio121"; + function = "gpio"; + + input-enable; + bias-disable; + }; + + kb_int_active_state: kb-int-active-state { + int-n-pins { + pins = "gpio37"; + function = "gpio"; + + bias-pull-up; + intput-enable; + }; + + kp-disable-pins { + pins = "gpio135"; + function = "gpio"; + + output-high; + }; + }; + + kb_tp_3v3_en_active_state: kb-tp-3v3-en-active-state { + pins = "gpio4"; + functino = "gpio"; + + bias-disable; + }; + + pcie2_default_state: pcie2-default-state { + clkreq-pins { + pins = "gpio176"; + function = "pci_e2"; + bias-pull-up; + }; + + reset-n-pins { + pins = "gpio175"; + function = "gpio"; + + drive-strength = <2>; + output-low; + bias-pull-down; + }; + + wake-n-pins { + pins = "gpio177"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + }; + + tp_int_active_state: tp-int-active-state { + tp-int-pins { + pins = "gpio24"; + function = "gpio"; + + bias-disable; + input-enable; + }; + + tp-close-n-pins { + pins = "gpio116"; + function = "gpio"; + + bias-disable; + input-enable; + }; + }; + + ts_active_state: ts-active-state { + int-n-pins { + pins = "gpio122"; + function = "gpio"; + + input-enable; + bias-disable; + }; + + reset-n-pins { + pins = "gpio54"; + function = "gpio"; + + output-high; + }; + }; + + ts_i2c_active_state: ts-i2c-active-state { + pins = "gpio114", "gpio115"; + function = "qup1"; + + /* External pull up */ + bias-disable; + drive-strength = <2>; + }; + + uart13_state: uart13-state { + cts-pins { + pins = "gpio43"; + function = "qup13"; + bias-pull-down; + }; + + rts-tx-pins { + pins = "gpio44", "gpio45"; + function = "qup13"; + drive-strength = <2>; + bias-disable; + }; + + rx-pins { + pins = "gpio46"; + function = "qup13"; + bias-pull-up; + }; + }; +};