@@ -13,6 +13,7 @@
#include <linux/pm_runtime.h>
#include <linux/regmap.h>
#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
#include <linux/slab.h>
#include <linux/soundwire/sdw.h>
#include <linux/soundwire/sdw_registers.h>
@@ -699,6 +700,7 @@ struct wsa884x_priv {
struct sdw_stream_runtime *sruntime;
struct sdw_port_config port_config[WSA884X_MAX_SWR_PORTS];
struct gpio_desc *sd_n;
+ struct reset_control *sd_reset;
bool port_prepared[WSA884X_MAX_SWR_PORTS];
bool port_enable[WSA884X_MAX_SWR_PORTS];
unsigned int variant;
@@ -1799,9 +1801,22 @@ static struct snd_soc_dai_driver wsa884x_dais[] = {
},
};
-static void wsa884x_gpio_powerdown(void *data)
+static void wsa884x_reset_powerdown(void *data)
{
- gpiod_direction_output(data, 1);
+ struct wsa884x_priv *wsa884x = data;
+
+ if (wsa884x->sd_reset)
+ reset_control_assert(wsa884x->sd_reset);
+ else
+ gpiod_direction_output(wsa884x->sd_n, 1);
+}
+
+static void wsa884x_reset_deassert(struct wsa884x_priv *wsa884x)
+{
+ if (wsa884x->sd_reset)
+ reset_control_deassert(wsa884x->sd_reset);
+ else
+ gpiod_direction_output(wsa884x->sd_n, 0);
}
static void wsa884x_regulator_disable(void *data)
@@ -1809,6 +1824,26 @@ static void wsa884x_regulator_disable(void *data)
regulator_bulk_disable(WSA884X_SUPPLIES_NUM, data);
}
+static int wsa884x_get_reset(struct device *dev, struct wsa884x_priv *wsa884x)
+{
+ wsa884x->sd_reset = devm_reset_control_get_optional_shared(dev, NULL);
+ if (IS_ERR(wsa884x->sd_reset))
+ return dev_err_probe(dev, PTR_ERR(wsa884x->sd_reset),
+ "Failed to get reset\n");
+
+ /*
+ * Backwards compatible way for powerdown-gpios, does not handle
+ * sharing GPIO properly.
+ */
+ wsa884x->sd_n = devm_gpiod_get_optional(dev, "powerdown",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(wsa884x->sd_n))
+ return dev_err_probe(dev, PTR_ERR(wsa884x->sd_n),
+ "Shutdown Control GPIO not found\n");
+
+ return 0;
+}
+
static int wsa884x_probe(struct sdw_slave *pdev,
const struct sdw_device_id *id)
{
@@ -1838,11 +1873,9 @@ static int wsa884x_probe(struct sdw_slave *pdev,
if (ret)
return ret;
- wsa884x->sd_n = devm_gpiod_get_optional(dev, "powerdown",
- GPIOD_OUT_HIGH);
- if (IS_ERR(wsa884x->sd_n))
- return dev_err_probe(dev, PTR_ERR(wsa884x->sd_n),
- "Shutdown Control GPIO not found\n");
+ ret = wsa884x_get_reset(dev, wsa884x);
+ if (ret)
+ return ret;
dev_set_drvdata(dev, wsa884x);
wsa884x->slave = pdev;
@@ -1858,9 +1891,8 @@ static int wsa884x_probe(struct sdw_slave *pdev,
pdev->prop.sink_dpn_prop = wsa884x_sink_dpn_prop;
pdev->prop.scp_int1_mask = SDW_SCP_INT1_BUS_CLASH | SDW_SCP_INT1_PARITY;
- /* Bring out of reset */
- gpiod_direction_output(wsa884x->sd_n, 0);
- ret = devm_add_action_or_reset(dev, wsa884x_gpio_powerdown, wsa884x->sd_n);
+ wsa884x_reset_deassert(wsa884x);
+ ret = devm_add_action_or_reset(dev, wsa884x_reset_powerdown, wsa884x);
if (ret)
return ret;
On some boards with multiple WSA8840/WSA8845 speakers, the reset (shutdown) GPIO is shared between two speakers. Use the reset controller framework and its "reset-gpio" driver to handle this case. This allows bring-up and proper handling of all WSA884x speakers on X1E80100-CRD board. Cc: Bartosz Golaszewski <brgl@bgdev.pl> Cc: Sean Anderson <sean.anderson@seco.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> --- If previous patches are fine, then this commit is independent and could be taken via ASoC. --- sound/soc/codecs/wsa884x.c | 52 ++++++++++++++++++++++++++++++-------- 1 file changed, 42 insertions(+), 10 deletions(-)