mbox series

[net-next,v6,0/9,RFT] net: dpaa: Convert to phylink

Message ID 20220930200933.4111249-1-sean.anderson@seco.com
Headers show
Series net: dpaa: Convert to phylink | expand

Message

Sean Anderson Sept. 30, 2022, 8:09 p.m. UTC
This series converts the DPAA driver to phylink.

I have tried to maintain backwards compatibility with existing device
trees whereever possible. However, one area where I was unable to
achieve this was with QSGMII. Please refer to patch 2 for details.

All mac drivers have now been converted. I would greatly appreciate if
anyone has T-series or P-series boards they can test/debug this series
on. I only have an LS1046ARDB. Everything but QSGMII should work without
breakage; QSGMII needs patches 7 and 8. For this reason, the last 4
patches in this series should be applied together (and should not go
through separate trees).

Changes in v6:
- Remove unnecessary $ref from renesas,rzn1-a5psw
- Remove unnecessary type from pcs-handle-names
- Add maxItems to pcs-handle
- Fix 81-character line
- Fix uninitialized variable in dtsec_mac_config

Changes in v5:
- Add Lynx PCS binding

Changes in v4:
- Use pcs-handle-names instead of pcs-names, as discussed
- Don't fail if phy support was not compiled in
- Split off rate adaptation series
- Split off DPAA "preparation" series
- Split off Lynx 10G support
- t208x: Mark MAC1 and MAC2 as 10G
- Add XFI PCS for t208x MAC1/MAC2

Changes in v3:
- Expand pcs-handle to an array
- Add vendor prefix 'fsl,' to rgmii and mii properties.
- Set maxItems for pcs-names
- Remove phy-* properties from example because dt-schema complains and I
  can't be bothered to figure out how to make it work.
- Add pcs-handle as a preferred version of pcsphy-handle
- Deprecate pcsphy-handle
- Remove mii/rmii properties
- Put the PCS mdiodev only after we are done with it (since the PCS
  does not perform a get itself).
- Remove _return label from memac_initialization in favor of returning
  directly
- Fix grabbing the default PCS not checking for -ENODATA from
  of_property_match_string
- Set DTSEC_ECNTRL_R100M in dtsec_link_up instead of dtsec_mac_config
- Remove rmii/mii properties
- Replace 1000Base... with 1000BASE... to match IEEE capitalization
- Add compatibles for QSGMII PCSs
- Split arm and powerpcs dts updates

Changes in v2:
- Better document how we select which PCS to use in the default case
- Move PCS_LYNX dependency to fman Kconfig
- Remove unused variable slow_10g_if
- Restrict valid link modes based on the phy interface. This is easier
  to set up, and mostly captures what I intended to do the first time.
  We now have a custom validate which restricts half-duplex for some SoCs
  for RGMII, but generally just uses the default phylink validate.
- Configure the SerDes in enable/disable
- Properly implement all ethtool ops and ioctls. These were mostly
  stubbed out just enough to compile last time.
- Convert 10GEC and dTSEC as well
- Fix capitalization of mEMAC in commit messages
- Add nodes for QSGMII PCSs
- Add nodes for QSGMII PCSs

Sean Anderson (9):
  dt-bindings: net: Expand pcs-handle to an array
  dt-bindings: net: Add Lynx PCS binding
  dt-bindings: net: fman: Add additional interface properties
  net: fman: memac: Add serdes support
  net: fman: memac: Use lynx pcs driver
  net: dpaa: Convert to phylink
  powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G
  powerpc: dts: qoriq: Add nodes for QSGMII PCSs
  arm64: dts: layerscape: Add nodes for QSGMII PCSs

 .../bindings/net/dsa/renesas,rzn1-a5psw.yaml  |   2 +-
 .../bindings/net/ethernet-controller.yaml     |  11 +-
 .../bindings/net/fsl,fman-dtsec.yaml          |  53 +-
 .../bindings/net/fsl,qoriq-mc-dpmac.yaml      |   2 +-
 .../devicetree/bindings/net/fsl-fman.txt      |   5 +-
 .../bindings/net/pcs/fsl,lynx-pcs.yaml        |  40 +
 .../boot/dts/freescale/fsl-ls1043-post.dtsi   |  24 +
 .../boot/dts/freescale/fsl-ls1046-post.dtsi   |  25 +
 .../fsl/qoriq-fman3-0-10g-0-best-effort.dtsi  |   3 +-
 .../boot/dts/fsl/qoriq-fman3-0-10g-0.dtsi     |  10 +-
 .../fsl/qoriq-fman3-0-10g-1-best-effort.dtsi  |  10 +-
 .../boot/dts/fsl/qoriq-fman3-0-10g-1.dtsi     |  10 +-
 .../boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi     |  45 ++
 .../boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi     |  45 ++
 .../boot/dts/fsl/qoriq-fman3-0-1g-0.dtsi      |   3 +-
 .../boot/dts/fsl/qoriq-fman3-0-1g-1.dtsi      |  10 +-
 .../boot/dts/fsl/qoriq-fman3-0-1g-2.dtsi      |  10 +-
 .../boot/dts/fsl/qoriq-fman3-0-1g-3.dtsi      |  10 +-
 .../boot/dts/fsl/qoriq-fman3-0-1g-4.dtsi      |   3 +-
 .../boot/dts/fsl/qoriq-fman3-0-1g-5.dtsi      |  10 +-
 .../boot/dts/fsl/qoriq-fman3-1-10g-0.dtsi     |  10 +-
 .../boot/dts/fsl/qoriq-fman3-1-10g-1.dtsi     |  10 +-
 .../boot/dts/fsl/qoriq-fman3-1-1g-0.dtsi      |   3 +-
 .../boot/dts/fsl/qoriq-fman3-1-1g-1.dtsi      |  10 +-
 .../boot/dts/fsl/qoriq-fman3-1-1g-2.dtsi      |  10 +-
 .../boot/dts/fsl/qoriq-fman3-1-1g-3.dtsi      |  10 +-
 .../boot/dts/fsl/qoriq-fman3-1-1g-4.dtsi      |   3 +-
 .../boot/dts/fsl/qoriq-fman3-1-1g-5.dtsi      |  10 +-
 arch/powerpc/boot/dts/fsl/t2081si-post.dtsi   |   4 +-
 drivers/net/ethernet/freescale/dpaa/Kconfig   |   4 +-
 .../net/ethernet/freescale/dpaa/dpaa_eth.c    |  89 +--
 .../ethernet/freescale/dpaa/dpaa_ethtool.c    |  90 +--
 drivers/net/ethernet/freescale/fman/Kconfig   |   4 +-
 .../net/ethernet/freescale/fman/fman_dtsec.c  | 460 +++++------
 .../net/ethernet/freescale/fman/fman_mac.h    |  10 -
 .../net/ethernet/freescale/fman/fman_memac.c  | 747 +++++++++---------
 .../net/ethernet/freescale/fman/fman_tgec.c   | 131 ++-
 drivers/net/ethernet/freescale/fman/mac.c     | 168 +---
 drivers/net/ethernet/freescale/fman/mac.h     |  23 +-
 39 files changed, 1076 insertions(+), 1051 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/net/pcs/fsl,lynx-pcs.yaml
 create mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi
 create mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi

Comments

Sean Anderson Oct. 4, 2022, 5:26 p.m. UTC | #1
On 10/4/22 12:52 PM, Jakub Kicinski wrote:
> On Tue, 4 Oct 2022 11:28:19 -0400 Sean Anderson wrote:
>> I noticed that this series was marked "RFC" in patchwork.
> 
> Because the cover letter has RTF in the subject, presumably.
> 
>> I consider this series ready to apply. I am requesting *testing*, in
>> particular on 10gec/dtsec boards (P-series). Since no one seems to
>> have tried that over the past 4 months that I've been working on this
>> series, perhaps the best way for it to get tested is to apply it...
> 
> You know the situation the best as the author, you should make 
> a clear call on the nature of the posting. It's either RFC/RFT 
> or a ready-to-go-in posting.

Well, I consider the memac stuff to be well tested, but I don't
have 10gec/dtsec hardware. I was hoping that someone with the hardware
might look at this series if I stuck RFT in the subject. I suspect
there are still some bugs in those drivers.

> Maybe in smaller subsystems you can post an RFC/RTF and then it 
> gets applied after some time without a repost but we don't do that.
> The normal processing time for a patch is 1-3 days while we like
> to give people a week to test. So the patches would have to rot in 
> the review queue for extra half a week. At our patch rate this is
> unsustainable.
> 

Well, I have gotten reviews for the device tree stuff, but the core
changes (what I consider to be the actual content of the series) is
missing Reviewed-bys. I don't anticipate making any major changes to
the series unless I get some feedback one way or another. If having
RFT in the subject is preventing that review, I will remove it.

--Sean