diff mbox series

[v3,7/7] arm64: dts: exynos: Add Exynos850 SoC support

Message ID 20210811114827.27322-8-semen.protsenko@linaro.org
State New
Headers show
Series [v3,1/7] dt-bindings: pinctrl: samsung: Add Exynos850 doc | expand

Commit Message

Sam Protsenko Aug. 11, 2021, 11:48 a.m. UTC
Samsung Exynos850 is ARMv8-based mobile-oriented SoC.

This patch adds minimal SoC support by including next Device Tree nodes:

1. Octa cores (Cortex-A55), supporting PSCI v1.0
2. ARM architecture timer (armv8-timer)
3. Interrupt controller (GIC-400)
4. Pinctrl nodes for GPIO
5. Serial node

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
---
Changes in v3:
 - Used generic fixed clock for serial

Changes in v2:
 * Commit message:
   - Documented added dts features instead of CPU features

 * exynos850-usi.dtsi:
   - Removed, moved everything to exynos850.dtsi

 * exynos850.dtsi:
   - Root node:
     - Added comment about engineering name (Exynos3830)
     - Renamed pinctrl nodes, adding domain names
     - Used hard coded IRQ numbers instead of named constants everywhere
     - Added soc node, moved next nodes there: gic, clock, pinctrls and
       serial
     - Used address-cells=1 for soc node and removed unneeded 0x0 from
       reg properties
     - Moved exynos850-pinctrl.dtsi include line to the end of
       exynos850.dtsi
     - Coding style fixes
   - cpus:
     - Used address-cells=1 for cpus node
     - Renamed cpu@0001 to cpu@1, and so on
     - Left only "arm,cortex-a55" for cpus compatible
     - Renamed reg = <0x0001> to <0x1> for cpus
   - armv8 timer:
     - Add comment about missing HV timer IRQ to armv8 timer node
     - Removed not existing properties from armv8 timer node
     - Fixed cpu number in CPU_MASK()
     - Removed obsolete clock-frequency property
   - GIC:
     - Fixed GIC type to be GIC-400
     - Fixed size of GIC's 2nd region to be 0x2000
   - serial node:
     - Hard coded clock number for serial_0 for now; will replace with
       named const once proper clock driver is implemented
     - Removed gate_uart_clk0 clock from serial_0, as that clock is not
       supported in serial driver anyway (yet)
   - clock node:
     - Fixed clock controller node name (@0x12.. -> @12..)

 * exynos850-pinctrl.dtsi:
   - Referenced pinctrl nodes instead of defining those again in root node
   - Fixed interrupt-cells (3 -> 2)
   - Fixed USI related comments for pin config nodes
   - Removed decon_f_te_* and fm_lna_en nodes (won't be used)
   - Reordered pin config nodes by pin numbers
   - Improved all comments
   - Used existing named constants for pin-function and pin-pud
   - Fixed node names (used hyphens instead of underscore)
   - Fixed warnings found in W=1 build

 .../boot/dts/exynos/exynos850-pinctrl.dtsi    | 748 ++++++++++++++++++
 arch/arm64/boot/dts/exynos/exynos850.dtsi     | 261 ++++++
 2 files changed, 1009 insertions(+)
 create mode 100644 arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
 create mode 100644 arch/arm64/boot/dts/exynos/exynos850.dtsi

Comments

Krzysztof Kozlowski Aug. 12, 2021, 8:17 a.m. UTC | #1
On 11/08/2021 13:48, Sam Protsenko wrote:
> Samsung Exynos850 is ARMv8-based mobile-oriented SoC.
> 
> This patch adds minimal SoC support by including next Device Tree nodes:
> 
> 1. Octa cores (Cortex-A55), supporting PSCI v1.0
> 2. ARM architecture timer (armv8-timer)
> 3. Interrupt controller (GIC-400)
> 4. Pinctrl nodes for GPIO
> 5. Serial node
> 
> Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
> ---
> Changes in v3:
>  - Used generic fixed clock for serial
> 
> Changes in v2:
>  * Commit message:
>    - Documented added dts features instead of CPU features
> 
>  * exynos850-usi.dtsi:
>    - Removed, moved everything to exynos850.dtsi
> 
>  * exynos850.dtsi:
>    - Root node:
>      - Added comment about engineering name (Exynos3830)
>      - Renamed pinctrl nodes, adding domain names
>      - Used hard coded IRQ numbers instead of named constants everywhere
>      - Added soc node, moved next nodes there: gic, clock, pinctrls and
>        serial
>      - Used address-cells=1 for soc node and removed unneeded 0x0 from
>        reg properties
>      - Moved exynos850-pinctrl.dtsi include line to the end of
>        exynos850.dtsi
>      - Coding style fixes
>    - cpus:
>      - Used address-cells=1 for cpus node
>      - Renamed cpu@0001 to cpu@1, and so on
>      - Left only "arm,cortex-a55" for cpus compatible
>      - Renamed reg = <0x0001> to <0x1> for cpus
>    - armv8 timer:
>      - Add comment about missing HV timer IRQ to armv8 timer node
>      - Removed not existing properties from armv8 timer node
>      - Fixed cpu number in CPU_MASK()
>      - Removed obsolete clock-frequency property
>    - GIC:
>      - Fixed GIC type to be GIC-400
>      - Fixed size of GIC's 2nd region to be 0x2000
>    - serial node:
>      - Hard coded clock number for serial_0 for now; will replace with
>        named const once proper clock driver is implemented
>      - Removed gate_uart_clk0 clock from serial_0, as that clock is not
>        supported in serial driver anyway (yet)
>    - clock node:
>      - Fixed clock controller node name (@0x12.. -> @12..)
> 
>  * exynos850-pinctrl.dtsi:
>    - Referenced pinctrl nodes instead of defining those again in root node
>    - Fixed interrupt-cells (3 -> 2)
>    - Fixed USI related comments for pin config nodes
>    - Removed decon_f_te_* and fm_lna_en nodes (won't be used)
>    - Reordered pin config nodes by pin numbers
>    - Improved all comments
>    - Used existing named constants for pin-function and pin-pud
>    - Fixed node names (used hyphens instead of underscore)
>    - Fixed warnings found in W=1 build
> 
>  .../boot/dts/exynos/exynos850-pinctrl.dtsi    | 748 ++++++++++++++++++
>  arch/arm64/boot/dts/exynos/exynos850.dtsi     | 261 ++++++
>  2 files changed, 1009 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
>  create mode 100644 arch/arm64/boot/dts/exynos/exynos850.dtsi
> 
> diff --git a/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> new file mode 100644
> index 000000000000..ba5d5f33e2f6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> @@ -0,0 +1,748 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung's Exynos850 SoC pin-mux and pin-config device tree source
> + *
> + * Copyright (C) 2017 Samsung Electronics Co., Ltd.
> + * Copyright (C) 2021 Linaro Ltd.
> + *
> + * Samsung's Exynos850 SoC pin-mux and pin-config options are listed as device
> + * tree nodes in this file.
> + */
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/pinctrl/samsung.h>
> +
> +&pinctrl_alive {
> +	gpa0: gpa0 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	gpa1: gpa1 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	gpa2: gpa2 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	gpa3: gpa3 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	gpa4: gpa4 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	gpq0: gpq0 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	/* I2C5 (also called CAM_PMIC_I2C in TRM) */
> +	i2c5_bus: i2c5-bus {
> +		samsung,pins = "gpa3-5", "gpa3-6";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	/* I2C6 (also called MOTOR_I2C in TRM) */
> +	i2c6_bus: i2c6-bus {
> +		samsung,pins = "gpa3-7", "gpa4-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	/* USI: UART */
> +	uart0_bus: uart0-bus {
> +		samsung,pins = "gpq0-0", "gpq0-1";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +};
> +
> +&pinctrl_cmgp {
> +	gpm0: gpm0 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	gpm1: gpm1 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	gpm2: gpm2 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	gpm3: gpm3 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	gpm4: gpm4 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	gpm5: gpm5 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		interrupt-parent = <&gic>;
> +		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	/* USI_CMGP0: HSI2C function */
> +	hsi2c3_bus: hsi2c3-bus {
> +		samsung,pins = "gpm0-0", "gpm1-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <0>;

There are also macros for DRV.

I assume you checked whether the actual values of FUNC/PULL/DRV macros
match Exynos850 datasheet.

> +	};
> +
> +	/* USI_CMGP0: UART function (4 pins, Auto Flow Control) */
> +	uart1_bus_single: uart1-bus {
> +		samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0", "gpm3-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	/* USI_CMGP0: UART function (2 pins, Non-Auto Flow Control) */
> +	uart1_bus_dual: uart1-bus-dual {
> +		samsung,pins = "gpm0-0", "gpm1-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	/* USI_CMGP0: SPI function */
> +	spi1_bus: spi1-bus {
> +		samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	spi1_cs: spi1-cs {
> +		samsung,pins = "gpm3-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	spi1_cs_func: spi1-cs-func {
> +		samsung,pins = "gpm3-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	/* USI_CMGP1: HSI2C function */
> +	hsi2c4_bus: hsi2c4-bus {
> +		samsung,pins = "gpm4-0", "gpm5-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	/* USI_CMGP1: UART function (4 pins, Auto Flow Control) */
> +	uart2_bus_single: uart2-bus {
> +		samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0", "gpm7-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	/* USI_CMGP1: UART function (2 pins, Non-Auto Flow Control) */
> +	uart2_bus_dual: uart2-bus-dual {
> +		samsung,pins = "gpm4-0", "gpm5-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +	};
> +
> +	/* USI_CMGP1: SPI function */
> +	spi2_bus: spi2-bus {
> +		samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	spi2_cs: spi2-cs {
> +		samsung,pins = "gpm7-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	spi2_cs_func: spi2-cs-func {
> +		samsung,pins = "gpm7-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <0>;
> +	};
> +};
> +
> +&pinctrl_aud {
> +	gpb0: gpb0 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	gpb1: gpb1 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	aud_codec_mclk: aud-codec-mclk {
> +		samsung,pins = "gpb0-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> +	};
> +
> +	aud_codec_mclk_idle: aud-codec-mclk-idle {
> +		samsung,pins = "gpb0-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> +	};
> +
> +	aud_i2s0_bus: aud-i2s0-bus {
> +		samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> +	};
> +
> +	aud_i2s0_idle: aud-i2s0-idle {
> +		samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> +	};
> +
> +	aud_i2s1_bus: aud-i2s1-bus {
> +		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> +	};
> +
> +	aud_i2s1_idle: aud-i2s1-idle {
> +		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> +	};
> +
> +	aud_fm_bus: aud-fm-bus {
> +		samsung,pins = "gpb1-4";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> +	};
> +
> +	aud_fm_idle: aud-fm-idle {
> +		samsung,pins = "gpb1-4";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> +	};
> +};
> +
> +&pinctrl_hsi {
> +	gpf2: gpf2 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	sd2_clk: sd2-clk {
> +		samsung,pins = "gpf2-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <2>;
> +	};
> +
> +	sd2_clk_fast_slew_rate_1x: sd2-clk-fast-slew-rate-1x {
> +		samsung,pins = "gpf2-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	sd2_clk_fast_slew_rate_1_5x: sd2-clk-fast-slew-rate-1-5x {
> +		samsung,pins = "gpf2-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <1>;
> +	};
> +
> +	sd2_clk_fast_slew_rate_2x: sd2-clk-fast-slew-rate-2x {
> +		samsung,pins = "gpf2-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <2>;
> +	};
> +
> +	sd2_clk_fast_slew_rate_2_5x: sd2-clk-fast-slew-rate-2-5x {
> +		samsung,pins = "gpf2-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <3>;
> +	};
> +
> +	sd2_clk_fast_slew_rate_3x: sd2-clk-fast-slew-rate-3x {
> +		samsung,pins = "gpf2-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <4>;
> +	};
> +
> +	sd2_clk_fast_slew_rate_4x: sd2-clk-fast-slew-rate-4x {
> +		samsung,pins = "gpf2-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <5>;
> +	};
> +
> +	sd2_cmd: sd2-cmd {
> +		samsung,pins = "gpf2-1";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <2>;
> +	 };
> +
> +	sd2_bus1: sd2-bus-width1 {
> +		samsung,pins = "gpf2-2";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <2>;
> +	};
> +
> +	sd2_bus4: sd2-bus-width4 {
> +		samsung,pins = "gpf2-3", "gpf2-4", "gpf2-5";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <2>;
> +	};
> +
> +	sd2_pins_as_pdn: sd2-pins-as-pdn {
> +		samsung,pins = "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
> +			       "gpf2-4", "gpf2-5";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> +	};
> +};
> +
> +&pinctrl_core {
> +	gpf0: gpf0 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	gpf1: gpf1 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	sd0_clk: sd0-clk {
> +		samsung,pins = "gpf0-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <3>;
> +	};
> +
> +	sd0_clk_fast_slew_rate_1x: sd0-clk-fast-slew-rate-1x {
> +		samsung,pins = "gpf0-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <1>;
> +	};
> +
> +	sd0_clk_fast_slew_rate_2x: sd0-clk-fast-slew-rate-2x {
> +		samsung,pins = "gpf0-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <2>;
> +	};
> +
> +	sd0_clk_fast_slew_rate_3x: sd0-clk-fast-slew-rate-3x {
> +		samsung,pins = "gpf0-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <2>;
> +	};
> +
> +	sd0_clk_fast_slew_rate_4x: sd0-clk-fast-slew-rate-4x {
> +		samsung,pins = "gpf0-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <3>;
> +	};
> +
> +	sd0_cmd: sd0-cmd {
> +		samsung,pins = "gpf0-1";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <3>;
> +	};
> +
> +	sd0_rdqs: sd0-rdqs {
> +		samsung,pins = "gpf0-2";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> +		samsung,pin-drv = <3>;
> +	};
> +
> +	sd0_nreset: sd0-nreset {
> +		samsung,pins = "gpf0-3";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <3>;
> +	};
> +
> +	sd0_bus1: sd0-bus-width1 {
> +		samsung,pins = "gpf1-0";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <3>;
> +	};
> +
> +	sd0_bus4: sd0-bus-width4 {
> +		samsung,pins = "gpf1-1", "gpf1-2", "gpf1-3";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <3>;
> +	};
> +
> +	sd0_bus8: sd0-bus-width8 {
> +		samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <3>;
> +	};
> +};
> +
> +&pinctrl_peri {
> +	gpg0: gpg0 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	gpp0: gpp0 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +	gpp1: gpp1 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	gpp2: gpp2 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	gpg1: gpg1 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	gpg2: gpg2 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	gpg3: gpg3 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	gpc0: gpc0 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	gpc1: gpc1 {
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +	};
> +
> +	/* USI: HSI2C0 */
> +	hsi2c0_bus: hsi2c0-bus {
> +		samsung,pins = "gpc1-0", "gpc1-1";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	/* USI: HSI2C1 */
> +	hsi2c1_bus: hsi2c1-bus {
> +		samsung,pins = "gpc1-2", "gpc1-3";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	/* USI: HSI2C2 */
> +	hsi2c2_bus: hsi2c2-bus {
> +		samsung,pins = "gpc1-4", "gpc1-5";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	/* USI: SPI */
> +	spi0_bus: spi0-bus {
> +		samsung,pins = "gpp2-0", "gpp2-2", "gpp2-3";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	spi0_cs: spi0-cs {
> +		samsung,pins = "gpp2-1";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	spi0_cs_func: spi0-cs-func {
> +		samsung,pins = "gpp2-1";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	i2c0_bus: i2c0-bus {
> +		samsung,pins = "gpp0-0", "gpp0-1";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	i2c1_bus: i2c1-bus {
> +		samsung,pins = "gpp0-2", "gpp0-3";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	i2c2_bus: i2c2-bus {
> +		samsung,pins = "gpp0-4", "gpp0-5";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	i2c3_bus: i2c3-bus {
> +		samsung,pins = "gpp1-0", "gpp1-1";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	i2c4_bus: i2c4-bus {
> +		samsung,pins = "gpp1-2", "gpp1-3";
> +		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> +		samsung,pin-drv = <0>;
> +	};
> +
> +	sensor_mclk0_in: sensor-mclk0-in {
> +		samsung,pins = "gpc0-0";

All these gpc0 go before hsi2c0_bus node (to have them ordered by
datasheet pin name).

> +		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> +		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> +		samsung,pin-drv = <2>;
> +	};
> +

Rest looks good but anyway will wait for the board DTS. :)

Best regards,
Krzysztof
Sam Protsenko Aug. 12, 2021, 5:42 p.m. UTC | #2
On Thu, 12 Aug 2021 at 11:17, Krzysztof Kozlowski
<krzysztof.kozlowski@canonical.com> wrote:
>
> On 11/08/2021 13:48, Sam Protsenko wrote:
> > Samsung Exynos850 is ARMv8-based mobile-oriented SoC.
> >
> > This patch adds minimal SoC support by including next Device Tree nodes:
> >
> > 1. Octa cores (Cortex-A55), supporting PSCI v1.0
> > 2. ARM architecture timer (armv8-timer)
> > 3. Interrupt controller (GIC-400)
> > 4. Pinctrl nodes for GPIO
> > 5. Serial node
> >
> > Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
> > ---
> > Changes in v3:
> >  - Used generic fixed clock for serial
> >
> > Changes in v2:
> >  * Commit message:
> >    - Documented added dts features instead of CPU features
> >
> >  * exynos850-usi.dtsi:
> >    - Removed, moved everything to exynos850.dtsi
> >
> >  * exynos850.dtsi:
> >    - Root node:
> >      - Added comment about engineering name (Exynos3830)
> >      - Renamed pinctrl nodes, adding domain names
> >      - Used hard coded IRQ numbers instead of named constants everywhere
> >      - Added soc node, moved next nodes there: gic, clock, pinctrls and
> >        serial
> >      - Used address-cells=1 for soc node and removed unneeded 0x0 from
> >        reg properties
> >      - Moved exynos850-pinctrl.dtsi include line to the end of
> >        exynos850.dtsi
> >      - Coding style fixes
> >    - cpus:
> >      - Used address-cells=1 for cpus node
> >      - Renamed cpu@0001 to cpu@1, and so on
> >      - Left only "arm,cortex-a55" for cpus compatible
> >      - Renamed reg = <0x0001> to <0x1> for cpus
> >    - armv8 timer:
> >      - Add comment about missing HV timer IRQ to armv8 timer node
> >      - Removed not existing properties from armv8 timer node
> >      - Fixed cpu number in CPU_MASK()
> >      - Removed obsolete clock-frequency property
> >    - GIC:
> >      - Fixed GIC type to be GIC-400
> >      - Fixed size of GIC's 2nd region to be 0x2000
> >    - serial node:
> >      - Hard coded clock number for serial_0 for now; will replace with
> >        named const once proper clock driver is implemented
> >      - Removed gate_uart_clk0 clock from serial_0, as that clock is not
> >        supported in serial driver anyway (yet)
> >    - clock node:
> >      - Fixed clock controller node name (@0x12.. -> @12..)
> >
> >  * exynos850-pinctrl.dtsi:
> >    - Referenced pinctrl nodes instead of defining those again in root node
> >    - Fixed interrupt-cells (3 -> 2)
> >    - Fixed USI related comments for pin config nodes
> >    - Removed decon_f_te_* and fm_lna_en nodes (won't be used)
> >    - Reordered pin config nodes by pin numbers
> >    - Improved all comments
> >    - Used existing named constants for pin-function and pin-pud
> >    - Fixed node names (used hyphens instead of underscore)
> >    - Fixed warnings found in W=1 build
> >
> >  .../boot/dts/exynos/exynos850-pinctrl.dtsi    | 748 ++++++++++++++++++
> >  arch/arm64/boot/dts/exynos/exynos850.dtsi     | 261 ++++++
> >  2 files changed, 1009 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> >  create mode 100644 arch/arm64/boot/dts/exynos/exynos850.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> > new file mode 100644
> > index 000000000000..ba5d5f33e2f6
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> > @@ -0,0 +1,748 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Samsung's Exynos850 SoC pin-mux and pin-config device tree source
> > + *
> > + * Copyright (C) 2017 Samsung Electronics Co., Ltd.
> > + * Copyright (C) 2021 Linaro Ltd.
> > + *
> > + * Samsung's Exynos850 SoC pin-mux and pin-config options are listed as device
> > + * tree nodes in this file.
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include <dt-bindings/pinctrl/samsung.h>
> > +
> > +&pinctrl_alive {
> > +     gpa0: gpa0 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +             interrupt-parent = <&gic>;
> > +             interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> > +     };
> > +
> > +     gpa1: gpa1 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +             interrupt-parent = <&gic>;
> > +             interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> > +     };
> > +
> > +     gpa2: gpa2 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +             interrupt-parent = <&gic>;
> > +             interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> > +     };
> > +
> > +     gpa3: gpa3 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +             interrupt-parent = <&gic>;
> > +             interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
> > +     };
> > +
> > +     gpa4: gpa4 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +             interrupt-parent = <&gic>;
> > +             interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
> > +                          <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> > +     };
> > +
> > +     gpq0: gpq0 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     /* I2C5 (also called CAM_PMIC_I2C in TRM) */
> > +     i2c5_bus: i2c5-bus {
> > +             samsung,pins = "gpa3-5", "gpa3-6";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     /* I2C6 (also called MOTOR_I2C in TRM) */
> > +     i2c6_bus: i2c6-bus {
> > +             samsung,pins = "gpa3-7", "gpa4-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     /* USI: UART */
> > +     uart0_bus: uart0-bus {
> > +             samsung,pins = "gpq0-0", "gpq0-1";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +     };
> > +};
> > +
> > +&pinctrl_cmgp {
> > +     gpm0: gpm0 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +             interrupt-parent = <&gic>;
> > +             interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
> > +     };
> > +
> > +     gpm1: gpm1 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +             interrupt-parent = <&gic>;
> > +             interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
> > +     };
> > +
> > +     gpm2: gpm2 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +             interrupt-parent = <&gic>;
> > +             interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
> > +     };
> > +
> > +     gpm3: gpm3 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +             interrupt-parent = <&gic>;
> > +             interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
> > +     };
> > +
> > +     gpm4: gpm4 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +             interrupt-parent = <&gic>;
> > +             interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
> > +     };
> > +
> > +     gpm5: gpm5 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +             interrupt-parent = <&gic>;
> > +             interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
> > +     };
> > +
> > +     /* USI_CMGP0: HSI2C function */
> > +     hsi2c3_bus: hsi2c3-bus {
> > +             samsung,pins = "gpm0-0", "gpm1-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <0>;
>
> There are also macros for DRV.
>

Unfortunately, existing DRV macros won't work for Exynos850. DRV
constants have different meaning for different GPIO domains in
Exynos850, so I thought introducing several groups of DRV constants
might be confusing. But please let me know if you still want me do
that.

> I assume you checked whether the actual values of FUNC/PULL/DRV macros
> match Exynos850 datasheet.
>

Yep, they are good.

> > +     };
> > +
> > +     /* USI_CMGP0: UART function (4 pins, Auto Flow Control) */
> > +     uart1_bus_single: uart1-bus {
> > +             samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0", "gpm3-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +     };
> > +
> > +     /* USI_CMGP0: UART function (2 pins, Non-Auto Flow Control) */
> > +     uart1_bus_dual: uart1-bus-dual {
> > +             samsung,pins = "gpm0-0", "gpm1-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +     };
> > +
> > +     /* USI_CMGP0: SPI function */
> > +     spi1_bus: spi1-bus {
> > +             samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     spi1_cs: spi1-cs {
> > +             samsung,pins = "gpm3-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     spi1_cs_func: spi1-cs-func {
> > +             samsung,pins = "gpm3-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     /* USI_CMGP1: HSI2C function */
> > +     hsi2c4_bus: hsi2c4-bus {
> > +             samsung,pins = "gpm4-0", "gpm5-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     /* USI_CMGP1: UART function (4 pins, Auto Flow Control) */
> > +     uart2_bus_single: uart2-bus {
> > +             samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0", "gpm7-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +     };
> > +
> > +     /* USI_CMGP1: UART function (2 pins, Non-Auto Flow Control) */
> > +     uart2_bus_dual: uart2-bus-dual {
> > +             samsung,pins = "gpm4-0", "gpm5-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +     };
> > +
> > +     /* USI_CMGP1: SPI function */
> > +     spi2_bus: spi2-bus {
> > +             samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     spi2_cs: spi2-cs {
> > +             samsung,pins = "gpm7-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     spi2_cs_func: spi2-cs-func {
> > +             samsung,pins = "gpm7-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +};
> > +
> > +&pinctrl_aud {
> > +     gpb0: gpb0 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     gpb1: gpb1 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     aud_codec_mclk: aud-codec-mclk {
> > +             samsung,pins = "gpb0-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > +     };
> > +
> > +     aud_codec_mclk_idle: aud-codec-mclk-idle {
> > +             samsung,pins = "gpb0-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > +     };
> > +
> > +     aud_i2s0_bus: aud-i2s0-bus {
> > +             samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > +     };
> > +
> > +     aud_i2s0_idle: aud-i2s0-idle {
> > +             samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > +     };
> > +
> > +     aud_i2s1_bus: aud-i2s1-bus {
> > +             samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > +     };
> > +
> > +     aud_i2s1_idle: aud-i2s1-idle {
> > +             samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > +     };
> > +
> > +     aud_fm_bus: aud-fm-bus {
> > +             samsung,pins = "gpb1-4";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > +     };
> > +
> > +     aud_fm_idle: aud-fm-idle {
> > +             samsung,pins = "gpb1-4";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > +     };
> > +};
> > +
> > +&pinctrl_hsi {
> > +     gpf2: gpf2 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     sd2_clk: sd2-clk {
> > +             samsung,pins = "gpf2-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <2>;
> > +     };
> > +
> > +     sd2_clk_fast_slew_rate_1x: sd2-clk-fast-slew-rate-1x {
> > +             samsung,pins = "gpf2-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     sd2_clk_fast_slew_rate_1_5x: sd2-clk-fast-slew-rate-1-5x {
> > +             samsung,pins = "gpf2-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <1>;
> > +     };
> > +
> > +     sd2_clk_fast_slew_rate_2x: sd2-clk-fast-slew-rate-2x {
> > +             samsung,pins = "gpf2-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <2>;
> > +     };
> > +
> > +     sd2_clk_fast_slew_rate_2_5x: sd2-clk-fast-slew-rate-2-5x {
> > +             samsung,pins = "gpf2-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <3>;
> > +     };
> > +
> > +     sd2_clk_fast_slew_rate_3x: sd2-clk-fast-slew-rate-3x {
> > +             samsung,pins = "gpf2-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <4>;
> > +     };
> > +
> > +     sd2_clk_fast_slew_rate_4x: sd2-clk-fast-slew-rate-4x {
> > +             samsung,pins = "gpf2-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <5>;
> > +     };
> > +
> > +     sd2_cmd: sd2-cmd {
> > +             samsung,pins = "gpf2-1";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <2>;
> > +      };
> > +
> > +     sd2_bus1: sd2-bus-width1 {
> > +             samsung,pins = "gpf2-2";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <2>;
> > +     };
> > +
> > +     sd2_bus4: sd2-bus-width4 {
> > +             samsung,pins = "gpf2-3", "gpf2-4", "gpf2-5";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <2>;
> > +     };
> > +
> > +     sd2_pins_as_pdn: sd2-pins-as-pdn {
> > +             samsung,pins = "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
> > +                            "gpf2-4", "gpf2-5";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > +     };
> > +};
> > +
> > +&pinctrl_core {
> > +     gpf0: gpf0 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     gpf1: gpf1 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     sd0_clk: sd0-clk {
> > +             samsung,pins = "gpf0-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <3>;
> > +     };
> > +
> > +     sd0_clk_fast_slew_rate_1x: sd0-clk-fast-slew-rate-1x {
> > +             samsung,pins = "gpf0-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <1>;
> > +     };
> > +
> > +     sd0_clk_fast_slew_rate_2x: sd0-clk-fast-slew-rate-2x {
> > +             samsung,pins = "gpf0-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <2>;
> > +     };
> > +
> > +     sd0_clk_fast_slew_rate_3x: sd0-clk-fast-slew-rate-3x {
> > +             samsung,pins = "gpf0-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <2>;
> > +     };
> > +
> > +     sd0_clk_fast_slew_rate_4x: sd0-clk-fast-slew-rate-4x {
> > +             samsung,pins = "gpf0-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <3>;
> > +     };
> > +
> > +     sd0_cmd: sd0-cmd {
> > +             samsung,pins = "gpf0-1";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <3>;
> > +     };
> > +
> > +     sd0_rdqs: sd0-rdqs {
> > +             samsung,pins = "gpf0-2";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> > +             samsung,pin-drv = <3>;
> > +     };
> > +
> > +     sd0_nreset: sd0-nreset {
> > +             samsung,pins = "gpf0-3";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <3>;
> > +     };
> > +
> > +     sd0_bus1: sd0-bus-width1 {
> > +             samsung,pins = "gpf1-0";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <3>;
> > +     };
> > +
> > +     sd0_bus4: sd0-bus-width4 {
> > +             samsung,pins = "gpf1-1", "gpf1-2", "gpf1-3";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <3>;
> > +     };
> > +
> > +     sd0_bus8: sd0-bus-width8 {
> > +             samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <3>;
> > +     };
> > +};
> > +
> > +&pinctrl_peri {
> > +     gpg0: gpg0 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     gpp0: gpp0 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +     gpp1: gpp1 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     gpp2: gpp2 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     gpg1: gpg1 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     gpg2: gpg2 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     gpg3: gpg3 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     gpc0: gpc0 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     gpc1: gpc1 {
> > +             gpio-controller;
> > +             #gpio-cells = <2>;
> > +
> > +             interrupt-controller;
> > +             #interrupt-cells = <2>;
> > +     };
> > +
> > +     /* USI: HSI2C0 */
> > +     hsi2c0_bus: hsi2c0-bus {
> > +             samsung,pins = "gpc1-0", "gpc1-1";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     /* USI: HSI2C1 */
> > +     hsi2c1_bus: hsi2c1-bus {
> > +             samsung,pins = "gpc1-2", "gpc1-3";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     /* USI: HSI2C2 */
> > +     hsi2c2_bus: hsi2c2-bus {
> > +             samsung,pins = "gpc1-4", "gpc1-5";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     /* USI: SPI */
> > +     spi0_bus: spi0-bus {
> > +             samsung,pins = "gpp2-0", "gpp2-2", "gpp2-3";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     spi0_cs: spi0-cs {
> > +             samsung,pins = "gpp2-1";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     spi0_cs_func: spi0-cs-func {
> > +             samsung,pins = "gpp2-1";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     i2c0_bus: i2c0-bus {
> > +             samsung,pins = "gpp0-0", "gpp0-1";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     i2c1_bus: i2c1-bus {
> > +             samsung,pins = "gpp0-2", "gpp0-3";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     i2c2_bus: i2c2-bus {
> > +             samsung,pins = "gpp0-4", "gpp0-5";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     i2c3_bus: i2c3-bus {
> > +             samsung,pins = "gpp1-0", "gpp1-1";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     i2c4_bus: i2c4-bus {
> > +             samsung,pins = "gpp1-2", "gpp1-3";
> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> > +             samsung,pin-drv = <0>;
> > +     };
> > +
> > +     sensor_mclk0_in: sensor-mclk0-in {
> > +             samsung,pins = "gpc0-0";
>
> All these gpc0 go before hsi2c0_bus node (to have them ordered by
> datasheet pin name).
>

Done.

> > +             samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> > +             samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> > +             samsung,pin-drv = <2>;
> > +     };
> > +
>
> Rest looks good but anyway will wait for the board DTS. :)
>

Sure. I'll probably send next patch series only when the board gets
announced, and will include board's dts of course.

> Best regards,
> Krzysztof
Rob Herring (Arm) Aug. 17, 2021, 6:42 p.m. UTC | #3
On Wed, Aug 11, 2021 at 02:48:27PM +0300, Sam Protsenko wrote:
> Samsung Exynos850 is ARMv8-based mobile-oriented SoC.

> 

> This patch adds minimal SoC support by including next Device Tree nodes:

> 

> 1. Octa cores (Cortex-A55), supporting PSCI v1.0

> 2. ARM architecture timer (armv8-timer)

> 3. Interrupt controller (GIC-400)

> 4. Pinctrl nodes for GPIO

> 5. Serial node

> 

> Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>

> ---

> Changes in v3:

>  - Used generic fixed clock for serial

> 

> Changes in v2:

>  * Commit message:

>    - Documented added dts features instead of CPU features

> 

>  * exynos850-usi.dtsi:

>    - Removed, moved everything to exynos850.dtsi

> 

>  * exynos850.dtsi:

>    - Root node:

>      - Added comment about engineering name (Exynos3830)

>      - Renamed pinctrl nodes, adding domain names

>      - Used hard coded IRQ numbers instead of named constants everywhere

>      - Added soc node, moved next nodes there: gic, clock, pinctrls and

>        serial

>      - Used address-cells=1 for soc node and removed unneeded 0x0 from

>        reg properties

>      - Moved exynos850-pinctrl.dtsi include line to the end of

>        exynos850.dtsi

>      - Coding style fixes

>    - cpus:

>      - Used address-cells=1 for cpus node

>      - Renamed cpu@0001 to cpu@1, and so on

>      - Left only "arm,cortex-a55" for cpus compatible

>      - Renamed reg = <0x0001> to <0x1> for cpus

>    - armv8 timer:

>      - Add comment about missing HV timer IRQ to armv8 timer node

>      - Removed not existing properties from armv8 timer node

>      - Fixed cpu number in CPU_MASK()

>      - Removed obsolete clock-frequency property

>    - GIC:

>      - Fixed GIC type to be GIC-400

>      - Fixed size of GIC's 2nd region to be 0x2000

>    - serial node:

>      - Hard coded clock number for serial_0 for now; will replace with

>        named const once proper clock driver is implemented

>      - Removed gate_uart_clk0 clock from serial_0, as that clock is not

>        supported in serial driver anyway (yet)

>    - clock node:

>      - Fixed clock controller node name (@0x12.. -> @12..)

> 

>  * exynos850-pinctrl.dtsi:

>    - Referenced pinctrl nodes instead of defining those again in root node

>    - Fixed interrupt-cells (3 -> 2)

>    - Fixed USI related comments for pin config nodes

>    - Removed decon_f_te_* and fm_lna_en nodes (won't be used)

>    - Reordered pin config nodes by pin numbers

>    - Improved all comments

>    - Used existing named constants for pin-function and pin-pud

>    - Fixed node names (used hyphens instead of underscore)

>    - Fixed warnings found in W=1 build

> 

>  .../boot/dts/exynos/exynos850-pinctrl.dtsi    | 748 ++++++++++++++++++

>  arch/arm64/boot/dts/exynos/exynos850.dtsi     | 261 ++++++

>  2 files changed, 1009 insertions(+)

>  create mode 100644 arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi

>  create mode 100644 arch/arm64/boot/dts/exynos/exynos850.dtsi

> 

> diff --git a/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi

> new file mode 100644

> index 000000000000..ba5d5f33e2f6

> --- /dev/null

> +++ b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi

> @@ -0,0 +1,748 @@

> +// SPDX-License-Identifier: GPL-2.0

> +/*

> + * Samsung's Exynos850 SoC pin-mux and pin-config device tree source

> + *

> + * Copyright (C) 2017 Samsung Electronics Co., Ltd.

> + * Copyright (C) 2021 Linaro Ltd.

> + *

> + * Samsung's Exynos850 SoC pin-mux and pin-config options are listed as device

> + * tree nodes in this file.

> + */

> +

> +#include <dt-bindings/interrupt-controller/arm-gic.h>

> +#include <dt-bindings/pinctrl/samsung.h>

> +

> +&pinctrl_alive {

> +	gpa0: gpa0 {

> +		gpio-controller;

> +		#gpio-cells = <2>;

> +

> +		interrupt-controller;

> +		#interrupt-cells = <2>;

> +		interrupt-parent = <&gic>;

> +		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;

> +	};

> +

> +	gpa1: gpa1 {

> +		gpio-controller;

> +		#gpio-cells = <2>;

> +

> +		interrupt-controller;

> +		#interrupt-cells = <2>;

> +		interrupt-parent = <&gic>;

> +		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;

> +	};

> +

> +	gpa2: gpa2 {

> +		gpio-controller;

> +		#gpio-cells = <2>;

> +

> +		interrupt-controller;

> +		#interrupt-cells = <2>;

> +		interrupt-parent = <&gic>;

> +		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;

> +	};

> +

> +	gpa3: gpa3 {

> +		gpio-controller;

> +		#gpio-cells = <2>;

> +

> +		interrupt-controller;

> +		#interrupt-cells = <2>;

> +		interrupt-parent = <&gic>;

> +		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;

> +	};

> +

> +	gpa4: gpa4 {

> +		gpio-controller;

> +		#gpio-cells = <2>;

> +

> +		interrupt-controller;

> +		#interrupt-cells = <2>;

> +		interrupt-parent = <&gic>;

> +		interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,

> +			     <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;

> +	};

> +

> +	gpq0: gpq0 {

> +		gpio-controller;

> +		#gpio-cells = <2>;

> +

> +		interrupt-controller;

> +		#interrupt-cells = <2>;

> +	};

> +

> +	/* I2C5 (also called CAM_PMIC_I2C in TRM) */

> +	i2c5_bus: i2c5-bus {


Please name all the pinctrl nodes with some pattern you can match on 
once there is a schema. '-pins$' is my suggestion.

> +		samsung,pins = "gpa3-5", "gpa3-6";

> +		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;

> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;

> +		samsung,pin-drv = <0>;

> +	};

> +

> +	/* I2C6 (also called MOTOR_I2C in TRM) */

> +	i2c6_bus: i2c6-bus {

> +		samsung,pins = "gpa3-7", "gpa4-0";

> +		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;

> +		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;

> +		samsung,pin-drv = <0>;

> +	};
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
new file mode 100644
index 000000000000..ba5d5f33e2f6
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
@@ -0,0 +1,748 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos850 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (C) 2017 Samsung Electronics Co., Ltd.
+ * Copyright (C) 2021 Linaro Ltd.
+ *
+ * Samsung's Exynos850 SoC pin-mux and pin-config options are listed as device
+ * tree nodes in this file.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/samsung.h>
+
+&pinctrl_alive {
+	gpa0: gpa0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpa1: gpa1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpa2: gpa2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpa3: gpa3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpa4: gpa4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpq0: gpq0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	/* I2C5 (also called CAM_PMIC_I2C in TRM) */
+	i2c5_bus: i2c5-bus {
+		samsung,pins = "gpa3-5", "gpa3-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	/* I2C6 (also called MOTOR_I2C in TRM) */
+	i2c6_bus: i2c6-bus {
+		samsung,pins = "gpa3-7", "gpa4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	/* USI: UART */
+	uart0_bus: uart0-bus {
+		samsung,pins = "gpq0-0", "gpq0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+};
+
+&pinctrl_cmgp {
+	gpm0: gpm0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm1: gpm1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm2: gpm2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm3: gpm3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm4: gpm4 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm5: gpm5 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	/* USI_CMGP0: HSI2C function */
+	hsi2c3_bus: hsi2c3-bus {
+		samsung,pins = "gpm0-0", "gpm1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	/* USI_CMGP0: UART function (4 pins, Auto Flow Control) */
+	uart1_bus_single: uart1-bus {
+		samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0", "gpm3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_CMGP0: UART function (2 pins, Non-Auto Flow Control) */
+	uart1_bus_dual: uart1-bus-dual {
+		samsung,pins = "gpm0-0", "gpm1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_CMGP0: SPI function */
+	spi1_bus: spi1-bus {
+		samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi1_cs: spi1-cs {
+		samsung,pins = "gpm3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi1_cs_func: spi1-cs-func {
+		samsung,pins = "gpm3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	/* USI_CMGP1: HSI2C function */
+	hsi2c4_bus: hsi2c4-bus {
+		samsung,pins = "gpm4-0", "gpm5-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	/* USI_CMGP1: UART function (4 pins, Auto Flow Control) */
+	uart2_bus_single: uart2-bus {
+		samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0", "gpm7-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_CMGP1: UART function (2 pins, Non-Auto Flow Control) */
+	uart2_bus_dual: uart2-bus-dual {
+		samsung,pins = "gpm4-0", "gpm5-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_CMGP1: SPI function */
+	spi2_bus: spi2-bus {
+		samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi2_cs: spi2-cs {
+		samsung,pins = "gpm7-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi2_cs_func: spi2-cs-func {
+		samsung,pins = "gpm7-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&pinctrl_aud {
+	gpb0: gpb0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb1: gpb1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	aud_codec_mclk: aud-codec-mclk {
+		samsung,pins = "gpb0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_codec_mclk_idle: aud-codec-mclk-idle {
+		samsung,pins = "gpb0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s0_bus: aud-i2s0-bus {
+		samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s0_idle: aud-i2s0-idle {
+		samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s1_bus: aud-i2s1-bus {
+		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s1_idle: aud-i2s1-idle {
+		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_fm_bus: aud-fm-bus {
+		samsung,pins = "gpb1-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_fm_idle: aud-fm-idle {
+		samsung,pins = "gpb1-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+};
+
+&pinctrl_hsi {
+	gpf2: gpf2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sd2_clk: sd2-clk {
+		samsung,pins = "gpf2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <2>;
+	};
+
+	sd2_clk_fast_slew_rate_1x: sd2-clk-fast-slew-rate-1x {
+		samsung,pins = "gpf2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	sd2_clk_fast_slew_rate_1_5x: sd2-clk-fast-slew-rate-1-5x {
+		samsung,pins = "gpf2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <1>;
+	};
+
+	sd2_clk_fast_slew_rate_2x: sd2-clk-fast-slew-rate-2x {
+		samsung,pins = "gpf2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <2>;
+	};
+
+	sd2_clk_fast_slew_rate_2_5x: sd2-clk-fast-slew-rate-2-5x {
+		samsung,pins = "gpf2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd2_clk_fast_slew_rate_3x: sd2-clk-fast-slew-rate-3x {
+		samsung,pins = "gpf2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <4>;
+	};
+
+	sd2_clk_fast_slew_rate_4x: sd2-clk-fast-slew-rate-4x {
+		samsung,pins = "gpf2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <5>;
+	};
+
+	sd2_cmd: sd2-cmd {
+		samsung,pins = "gpf2-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <2>;
+	 };
+
+	sd2_bus1: sd2-bus-width1 {
+		samsung,pins = "gpf2-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <2>;
+	};
+
+	sd2_bus4: sd2-bus-width4 {
+		samsung,pins = "gpf2-3", "gpf2-4", "gpf2-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <2>;
+	};
+
+	sd2_pins_as_pdn: sd2-pins-as-pdn {
+		samsung,pins = "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
+			       "gpf2-4", "gpf2-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+};
+
+&pinctrl_core {
+	gpf0: gpf0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf1: gpf1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sd0_clk: sd0-clk {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_clk_fast_slew_rate_1x: sd0-clk-fast-slew-rate-1x {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <1>;
+	};
+
+	sd0_clk_fast_slew_rate_2x: sd0-clk-fast-slew-rate-2x {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <2>;
+	};
+
+	sd0_clk_fast_slew_rate_3x: sd0-clk-fast-slew-rate-3x {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <2>;
+	};
+
+	sd0_clk_fast_slew_rate_4x: sd0-clk-fast-slew-rate-4x {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_cmd: sd0-cmd {
+		samsung,pins = "gpf0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_rdqs: sd0-rdqs {
+		samsung,pins = "gpf0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_nreset: sd0-nreset {
+		samsung,pins = "gpf0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus1: sd0-bus-width1 {
+		samsung,pins = "gpf1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus4: sd0-bus-width4 {
+		samsung,pins = "gpf1-1", "gpf1-2", "gpf1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+
+	sd0_bus8: sd0-bus-width8 {
+		samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <3>;
+	};
+};
+
+&pinctrl_peri {
+	gpg0: gpg0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp0: gpp0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+	gpp1: gpp1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp2: gpp2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg1: gpg1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg2: gpg2 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg3: gpg3 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc0: gpc0 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc1: gpc1 {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	/* USI: HSI2C0 */
+	hsi2c0_bus: hsi2c0-bus {
+		samsung,pins = "gpc1-0", "gpc1-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	/* USI: HSI2C1 */
+	hsi2c1_bus: hsi2c1-bus {
+		samsung,pins = "gpc1-2", "gpc1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	/* USI: HSI2C2 */
+	hsi2c2_bus: hsi2c2-bus {
+		samsung,pins = "gpc1-4", "gpc1-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	/* USI: SPI */
+	spi0_bus: spi0-bus {
+		samsung,pins = "gpp2-0", "gpp2-2", "gpp2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi0_cs: spi0-cs {
+		samsung,pins = "gpp2-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	spi0_cs_func: spi0-cs-func {
+		samsung,pins = "gpp2-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c0_bus: i2c0-bus {
+		samsung,pins = "gpp0-0", "gpp0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c1_bus: i2c1-bus {
+		samsung,pins = "gpp0-2", "gpp0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c2_bus: i2c2-bus {
+		samsung,pins = "gpp0-4", "gpp0-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c3_bus: i2c3-bus {
+		samsung,pins = "gpp1-0", "gpp1-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	i2c4_bus: i2c4-bus {
+		samsung,pins = "gpp1-2", "gpp1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <0>;
+	};
+
+	sensor_mclk0_in: sensor-mclk0-in {
+		samsung,pins = "gpc0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <2>;
+	};
+
+	sensor_mclk0_out: sensor-mclk0-out {
+		samsung,pins = "gpc0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <2>;
+	};
+
+	sensor_mclk0_fn: sensor-mclk0-fn {
+		samsung,pins = "gpc0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <2>;
+	};
+
+	sensor_mclk1_in: sensor-mclk1-in {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <2>;
+	};
+
+	sensor_mclk1_out: sensor-mclk1-out {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <2>;
+	};
+
+	sensor_mclk1_fn: sensor-mclk1-fn {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <2>;
+	};
+
+	sensor_mclk2_in: sensor-mclk2-in {
+		samsung,pins = "gpc0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <2>;
+	};
+
+	sensor_mclk2_out: sensor-mclk2-out {
+		samsung,pins = "gpc0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <2>;
+	};
+
+	sensor_mclk2_fn: sensor-mclk2-fn {
+		samsung,pins = "gpc0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <2>;
+	};
+
+	xclkout: xclkout {
+		samsung,pins = "gpq0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos850.dtsi b/arch/arm64/boot/dts/exynos/exynos850.dtsi
new file mode 100644
index 000000000000..2360f142159f
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos850.dtsi
@@ -0,0 +1,261 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung Exynos850 SoC device tree source
+ *
+ * Copyright (C) 2018 Samsung Electronics Co., Ltd.
+ * Copyright (C) 2021 Linaro Ltd.
+ *
+ * Samsung Exynos850 SoC device nodes are listed in this file.
+ * Exynos based board files can include this file and provide
+ * values for board specific bindings.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	/* Also known under engineering name Exynos3830 */
+	compatible = "samsung,exynos850";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <1>;
+
+	aliases {
+		pinctrl0 = &pinctrl_alive;
+		pinctrl1 = &pinctrl_cmgp;
+		pinctrl2 = &pinctrl_aud;
+		pinctrl3 = &pinctrl_hsi;
+		pinctrl4 = &pinctrl_core;
+		pinctrl5 = &pinctrl_peri;
+		serial0 = &serial_0;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu4>;
+				};
+				core1 {
+					cpu = <&cpu5>;
+				};
+				core2 {
+					cpu = <&cpu6>;
+				};
+				core3 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0>;
+			enable-method = "psci";
+		};
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x1>;
+			enable-method = "psci";
+		};
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x2>;
+			enable-method = "psci";
+		};
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x3>;
+			enable-method = "psci";
+		};
+		cpu4: cpu@4 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x100>;
+			enable-method = "psci";
+		};
+		cpu5: cpu@5 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x101>;
+			enable-method = "psci";
+		};
+		cpu6: cpu@6 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x102>;
+			enable-method = "psci";
+		};
+		cpu7: cpu@7 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x103>;
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		/* Hypervisor Virtual Timer interrupt is not wired to GIC */
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) |
+					  IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) |
+					  IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	soc: soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x20000000>;
+
+		gic: interrupt-controller@12a01000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			reg = <0x12a01000 0x1000>,
+			      <0x12a02000 0x2000>,
+			      <0x12a04000 0x2000>,
+			      <0x12a06000 0x2000>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) |
+						 IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		/*
+		 * Keep the stub clock for serial driver, until proper clock
+		 * driver is implemented.
+		 */
+		uart_clock: uart-clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+			clock-output-names = "uart";
+		};
+
+		pinctrl_alive: pinctrl@11850000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x11850000 0x1000>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+
+			wakeup-interrupt-controller {
+				compatible = "samsung,exynos7-wakeup-eint";
+			};
+		};
+
+		pinctrl_cmgp: pinctrl@11c30000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x11c30000 0x1000>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+
+			wakeup-interrupt-controller {
+				compatible = "samsung,exynos7-wakeup-eint";
+			};
+		};
+
+		pinctrl_aud: pinctrl@14a60000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x14a60000 0x1000>;
+		};
+
+		pinctrl_hsi: pinctrl@13430000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x13430000 0x1000>;
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_core: pinctrl@12070000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x12070000 0x1000>;
+			interrupts = <GIC_SPI 451 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_peri: pinctrl@139b0000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x139b0000 0x1000>;
+			interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		/* USI: UART */
+		serial_0: uart@13820000 {
+			compatible = "samsung,exynos850-uart";
+			reg = <0x13820000 0x100>;
+			interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_bus>;
+			clocks = <&uart_clock>;
+			clock-names = "uart";
+			status = "disabled";
+		};
+	};
+};
+
+#include "exynos850-pinctrl.dtsi"