diff mbox series

[v4,3/3] misc: uwb: nxp: sr1xx: UWB driver support for sr1xx series chip

Message ID 20220527184351.3829543-4-manjunatha.venkatesh@nxp.com
State New
Headers show
Series [v4,1/3] dt-bindings: uwb: Device tree information for Nxp SR1XX SOCs | expand

Commit Message

Manjunatha Venkatesh May 27, 2022, 6:43 p.m. UTC
Ultra-wideband (UWB) is a short-range wireless communication protocol.

NXP has SR1XX family of UWB Subsystems (UWBS) devices. SR1XX SOCs
are FiRa Compliant. SR1XX SOCs are flash less devices and they need
Firmware Download on every device boot. More details on the SR1XX Family
can be found at https://www.nxp.com/products/:UWB-TRIMENSION

The sr1xx driver work the SR1XX Family of UWBS, and uses UWB Controller
Interface (UCI).  The corresponding details are available in the FiRa
Consortium Website (https://www.firaconsortium.org/).

Internally driver will handle two modes of operation.
1.HBCI mode (sr1xx BootROM Code Interface)
Firmware download uses HBCI ptotocol packet structure which is
Nxp proprietary,Firmware File(.bin) stored in user space context
and during device init sequence pick the firmware packet in chunk
and send it to the driver with write() api call.

After the firmware download sequence at the end UWBS will
send device status notification and its indication of device entered
UCI mode.
Here after any command/response/notification will follow
UCI packet structure.

2.UCI mode (UWB Command interface)
Once Firmware download finishes sr1xx will switch to UCI mode.
Then driver exchange command/response/notification as per the FIRA UCI
standard format between user space and sr1xx device.
Any response or notification received from sr1xx through SPI line
will convey to user space.

Its Interrupt based driver and IO Handshake needed with SR1XX Family of
SOCs.
This driver needs dts config update as per the sr1xx data sheet.
Corresponding document available in Documentation/devicetree/bindings/uwb

Message-ID: <20220504171337.3416983-1-manjunatha.venkatesh@nxp.com>
Signed-off-by: Manjunatha Venkatesh <manjunatha.venkatesh@nxp.com>
---
Changes since v3:
  - Commit Message Description updated
  - Renamed file from sr1xx.c to nxp-sr1xx.c
  - Removed unwanted header files
  - Removed sr1xx.h file since its not required for single source file

 drivers/misc/Kconfig     |  12 +
 drivers/misc/Makefile    |   1 +
 drivers/misc/nxp-sr1xx.c | 834 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 847 insertions(+)
 create mode 100644 drivers/misc/nxp-sr1xx.c

Comments

kernel test robot May 28, 2022, 1:23 a.m. UTC | #1
Hi Manjunatha,

I love your patch! Perhaps something to improve:

[auto build test WARNING on char-misc/char-misc-testing]
[also build test WARNING on robh/for-next linus/master v5.18 next-20220527]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/intel-lab-lkp/linux/commits/Manjunatha-Venkatesh/dt-bindings-uwb-Device-tree-information-for-Nxp-SR1XX-SOCs/20220528-034415
base:   https://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc.git 90de6805267f8c79cd2b1a36805071e257c39b5c
config: sh-allmodconfig (https://download.01.org/0day-ci/archive/20220528/202205280934.M6HHdGSK-lkp@intel.com/config)
compiler: sh4-linux-gcc (GCC) 11.3.0
reproduce (this is a W=1 build):
        wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
        chmod +x ~/bin/make.cross
        # https://github.com/intel-lab-lkp/linux/commit/948442a0588504d3fecae99073e785e5af6346bc
        git remote add linux-review https://github.com/intel-lab-lkp/linux
        git fetch --no-tags linux-review Manjunatha-Venkatesh/dt-bindings-uwb-Device-tree-information-for-Nxp-SR1XX-SOCs/20220528-034415
        git checkout 948442a0588504d3fecae99073e785e5af6346bc
        # save the config file
        mkdir build_dir && cp config build_dir/.config
        COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.3.0 make.cross W=1 O=build_dir ARCH=sh SHELL=/bin/bash drivers/

If you fix the issue, kindly add following tag where applicable
Reported-by: kernel test robot <lkp@intel.com>

All warnings (new ones prefixed by >>):

>> drivers/misc/nxp-sr1xx.c:175:6: warning: no previous prototype for 'sr1xx_wait_for_irq_gpio_low' [-Wmissing-prototypes]
     175 | void sr1xx_wait_for_irq_gpio_low(struct sr1xx_dev *sr1xx_dev)
         |      ^~~~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/misc/nxp-sr1xx.c:770:5: warning: no previous prototype for 'sr1xx_dev_suspend' [-Wmissing-prototypes]
     770 | int sr1xx_dev_suspend(struct device *dev)
         |     ^~~~~~~~~~~~~~~~~
>> drivers/misc/nxp-sr1xx.c:786:5: warning: no previous prototype for 'sr1xx_dev_resume' [-Wmissing-prototypes]
     786 | int sr1xx_dev_resume(struct device *dev)
         |     ^~~~~~~~~~~~~~~~


vim +/sr1xx_wait_for_irq_gpio_low +175 drivers/misc/nxp-sr1xx.c

   168	
   169	/**
   170	 * sr1xx_wait_for_irq_gpio_low
   171	 *
   172	 * Function to wait till irq gpio goes low state
   173	 *
   174	 */
 > 175	void sr1xx_wait_for_irq_gpio_low(struct sr1xx_dev *sr1xx_dev)
   176	{
   177		int retry_count = 0;
   178	
   179		do {
   180			udelay(10);
   181			retry_count++;
   182			if (retry_count == MAX_RETRY_COUNT_FOR_HANDSHAKE) {
   183				dev_info(&sr1xx_dev->spi->dev,
   184					 "Slave not released the IRQ even after 10ms");
   185				break;
   186			}
   187		} while (gpio_get_value(sr1xx_dev->irq_gpio));
   188	}
   189
Krzysztof Kozlowski May 29, 2022, 11:42 a.m. UTC | #2
On 27/05/2022 20:43, Manjunatha Venkatesh wrote:
> Ultra-wideband (UWB) is a short-range wireless communication protocol.
> 
> NXP has SR1XX family of UWB Subsystems (UWBS) devices. SR1XX SOCs
> are FiRa Compliant. SR1XX SOCs are flash less devices and they need
> Firmware Download on every device boot. More details on the SR1XX Family
> can be found at https://www.nxp.com/products/:UWB-TRIMENSION
> 
> The sr1xx driver work the SR1XX Family of UWBS, and uses UWB Controller
> Interface (UCI).  The corresponding details are available in the FiRa
> Consortium Website (https://www.firaconsortium.org/).
> 
> Internally driver will handle two modes of operation.
> 1.HBCI mode (sr1xx BootROM Code Interface)
> Firmware download uses HBCI ptotocol packet structure which is
> Nxp proprietary,Firmware File(.bin) stored in user space context
> and during device init sequence pick the firmware packet in chunk
> and send it to the driver with write() api call.
> 
> After the firmware download sequence at the end UWBS will
> send device status notification and its indication of device entered
> UCI mode.
> Here after any command/response/notification will follow
> UCI packet structure.
> 
> 2.UCI mode (UWB Command interface)
> Once Firmware download finishes sr1xx will switch to UCI mode.
> Then driver exchange command/response/notification as per the FIRA UCI
> standard format between user space and sr1xx device.
> Any response or notification received from sr1xx through SPI line
> will convey to user space.
> 
> Its Interrupt based driver and IO Handshake needed with SR1XX Family of
> SOCs.
> This driver needs dts config update as per the sr1xx data sheet.
> Corresponding document available in Documentation/devicetree/bindings/uwb
> 
> Message-ID: <20220504171337.3416983-1-manjunatha.venkatesh@nxp.com>

Same comment.


> Signed-off-by: Manjunatha Venkatesh <manjunatha.venkatesh@nxp.com>
> ---
> Changes since v3:
>   - Commit Message Description updated
>   - Renamed file from sr1xx.c to nxp-sr1xx.c
>   - Removed unwanted header files
>   - Removed sr1xx.h file since its not required for single source file
> 

Thank you for your patch. There is something to discuss/improve.

>  drivers/misc/Kconfig     |  12 +
>  drivers/misc/Makefile    |   1 +
>  drivers/misc/nxp-sr1xx.c | 834 +++++++++++++++++++++++++++++++++++++++
>  3 files changed, 847 insertions(+)
>  create mode 100644 drivers/misc/nxp-sr1xx.c
> 
> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
> index 41d2bb0ae23a..4f81d5758940 100644
> --- a/drivers/misc/Kconfig
> +++ b/drivers/misc/Kconfig
> @@ -483,6 +483,18 @@ config OPEN_DICE
>  
>  	  If unsure, say N.
>  
> +config NXP_UWB

It is not a misc driver. It is communication driver, so closer to
network. Please find appropriate subsystem.

> +        tristate "Nxp UCI(Uwb Command Interface) protocol driver support"

Isn't the name of company NXP?

> +        depends on SPI
> +        help
> +        This option enables the UWB driver for Nxp sr1xx

The same...

> +        device. Such device supports UCI packet structure,
> +        FiRa compliant.
> +
> +        Say Y here to compile support for sr1xx into the kernel or
> +        say M to compile it as a module. The module will be called
> +        sr1xx.ko
> +
>  source "drivers/misc/c2port/Kconfig"
>  source "drivers/misc/eeprom/Kconfig"
>  source "drivers/misc/cb710/Kconfig"
> diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
> index 70e800e9127f..d4e6e4f1ec29 100644
> --- a/drivers/misc/Makefile
> +++ b/drivers/misc/Makefile
> @@ -60,3 +60,4 @@ obj-$(CONFIG_XILINX_SDFEC)	+= xilinx_sdfec.o
>  obj-$(CONFIG_HISI_HIKEY_USB)	+= hisi_hikey_usb.o
>  obj-$(CONFIG_HI6421V600_IRQ)	+= hi6421v600-irq.o
>  obj-$(CONFIG_OPEN_DICE)		+= open-dice.o
> +obj-$(CONFIG_NXP_UWB) 		+= nxp-sr1xx.o

Looks like wrong order.

> diff --git a/drivers/misc/nxp-sr1xx.c b/drivers/misc/nxp-sr1xx.c
> new file mode 100644
> index 000000000000..25648712a61b
> --- /dev/null
> +++ b/drivers/misc/nxp-sr1xx.c
> @@ -0,0 +1,834 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * SPI driver for UWB SR1xx
> + * Copyright (C) 2018-2022 NXP.
> + *
> + * Author: Manjunatha Venkatesh <manjunatha.venkatesh@nxp.com>
> + */
> +#include <linux/miscdevice.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/of_gpio.h>
> +#include <linux/spi/spi.h>
> +
> +#define SR1XX_MAGIC 0xEA
> +#define SR1XX_SET_PWR _IOW(SR1XX_MAGIC, 0x01, long)
> +#define SR1XX_SET_FWD _IOW(SR1XX_MAGIC, 0x02, long)
> +
> +#define UCI_HEADER_LEN 4
> +#define HBCI_HEADER_LEN 4
> +#define UCI_PAYLOAD_LEN_OFFSET 3
> +
> +#define UCI_EXT_PAYLOAD_LEN_IND_OFFSET 1
> +#define UCI_EXT_PAYLOAD_LEN_IND_OFFSET_MASK 0x80
> +#define UCI_EXT_PAYLOAD_LEN_OFFSET 2
> +
> +#define SR1XX_TXBUF_SIZE 4200
> +#define SR1XX_RXBUF_SIZE 4200
> +#define SR1XX_MAX_TX_BUF_SIZE 4200
> +
> +#define MAX_RETRY_COUNT_FOR_IRQ_CHECK 100
> +#define MAX_RETRY_COUNT_FOR_HANDSHAKE 1000
> +

(...)

> +
> +static const struct dev_pm_ops sr1xx_dev_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(
> +	sr1xx_dev_suspend, sr1xx_dev_resume) };
> +
> +static struct spi_driver sr1xx_driver = {
> +	.driver = {
> +		   .name = "sr1xx",
> +		   .pm = &sr1xx_dev_pm_ops,
> +		   .bus = &spi_bus_type,
> +		   .owner = THIS_MODULE,

No, this was removed some years ago... Please run all regular static
tools on your code sparse, smatch and coccinelle.

There is no need for us to do the review of things pointed out by tools.


> +		   .of_match_table = sr1xx_dt_match,
> +		    },
> +	.probe = sr1xx_probe,
> +	.remove = sr1xx_remove,
> +};
> +
> +static int __init sr1xx_dev_init(void)
> +{
> +	return spi_register_driver(&sr1xx_driver);
> +}
> +
> +module_init(sr1xx_dev_init);
> +
> +static void __exit sr1xx_dev_exit(void)
> +{
> +	spi_unregister_driver(&sr1xx_driver);
> +}

Why this isn't a module_spi_driver?

> +
> +module_exit(sr1xx_dev_exit);
> +
> +MODULE_AUTHOR("Manjunatha Venkatesh <manjunatha.venkatesh@nxp.com>");
> +MODULE_DESCRIPTION("NXP SR1XX SPI driver");
> +MODULE_LICENSE("GPL");


Best regards,
Krzysztof
Christophe JAILLET May 29, 2022, 1:28 p.m. UTC | #3
Le 27/05/2022 à 20:43, Manjunatha Venkatesh a écrit :
> Ultra-wideband (UWB) is a short-range wireless communication protocol.
> 

Hi,

below a few comments, mainly around the probe function.
Maybe using devm_gpio_request() and devm_kzalloc() could help and 
simplify the error handling path/.remove function.

Just my 2c if it helps.

CJ


[...]
> 
> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
> index 41d2bb0ae23a..4f81d5758940 100644
> --- a/drivers/misc/Kconfig
> +++ b/drivers/misc/Kconfig
> @@ -483,6 +483,18 @@ config OPEN_DICE
>   
>   	  If unsure, say N.
>   
> +config NXP_UWB
> +        tristate "Nxp UCI(Uwb Command Interface) protocol driver support"
> +        depends on SPI
> +        help
> +        This option enables the UWB driver for Nxp sr1xx
> +        device. Such device supports UCI packet structure,
> +        FiRa compliant.
> +
> +        Say Y here to compile support for sr1xx into the kernel or
> +        say M to compile it as a module. The module will be called
> +        sr1xx.ko
> +
>   source "drivers/misc/c2port/Kconfig"
>   source "drivers/misc/eeprom/Kconfig"
>   source "drivers/misc/cb710/Kconfig"
> diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
> index 70e800e9127f..d4e6e4f1ec29 100644
> --- a/drivers/misc/Makefile
> +++ b/drivers/misc/Makefile
> @@ -60,3 +60,4 @@ obj-$(CONFIG_XILINX_SDFEC)	+= xilinx_sdfec.o
>   obj-$(CONFIG_HISI_HIKEY_USB)	+= hisi_hikey_usb.o
>   obj-$(CONFIG_HI6421V600_IRQ)	+= hi6421v600-irq.o
>   obj-$(CONFIG_OPEN_DICE)		+= open-dice.o
> +obj-$(CONFIG_NXP_UWB) 		+= nxp-sr1xx.o
> diff --git a/drivers/misc/nxp-sr1xx.c b/drivers/misc/nxp-sr1xx.c
> new file mode 100644
> index 000000000000..25648712a61b
> --- /dev/null
> +++ b/drivers/misc/nxp-sr1xx.c
> @@ -0,0 +1,834 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * SPI driver for UWB SR1xx
> + * Copyright (C) 2018-2022 NXP.
> + *
> + * Author: Manjunatha Venkatesh <manjunatha.venkatesh-3arQi8VN3Tc@public.gmane.org>
> + */
> +#include <linux/miscdevice.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/of_gpio.h>
> +#include <linux/spi/spi.h>
> +
> +#define SR1XX_MAGIC 0xEA
> +#define SR1XX_SET_PWR _IOW(SR1XX_MAGIC, 0x01, long)
> +#define SR1XX_SET_FWD _IOW(SR1XX_MAGIC, 0x02, long)
> +
> +#define UCI_HEADER_LEN 4
> +#define HBCI_HEADER_LEN 4
> +#define UCI_PAYLOAD_LEN_OFFSET 3
> +
> +#define UCI_EXT_PAYLOAD_LEN_IND_OFFSET 1
> +#define UCI_EXT_PAYLOAD_LEN_IND_OFFSET_MASK 0x80
> +#define UCI_EXT_PAYLOAD_LEN_OFFSET 2
> +
> +#define SR1XX_TXBUF_SIZE 4200
> +#define SR1XX_RXBUF_SIZE 4200
> +#define SR1XX_MAX_TX_BUF_SIZE 4200
> +
> +#define MAX_RETRY_COUNT_FOR_IRQ_CHECK 100
> +#define MAX_RETRY_COUNT_FOR_HANDSHAKE 1000
> +
> +/* Macro to define SPI clock frequency */
> +#define SR1XX_SPI_CLOCK 16000000L
> +#define WAKEUP_SRC_TIMEOUT (2000)
> +
> +/* Maximum UCI packet size supported from the driver */
> +#define MAX_UCI_PKT_SIZE 4200
> +
> +struct sr1xx_spi_platform_data {
> +	unsigned int irq_gpio; /* SR1XX will interrupt host for any ntf */
> +	unsigned int ce_gpio; /* SW reset gpio */
> +	unsigned int spi_handshake_gpio; /* Host ready to read data */
> +};
> +
> +/* Device specific macro and structure */
> +struct sr1xx_dev {
> +	wait_queue_head_t read_wq; /* Wait queue for read interrupt */
> +	struct spi_device *spi; /* Spi device structure */
> +	struct miscdevice sr1xx_device; /* Char device as misc driver */
> +	unsigned int ce_gpio; /* SW reset gpio */
> +	unsigned int irq_gpio; /* SR1XX will interrupt host for any ntf */
> +	unsigned int spi_handshake_gpio; /* Host ready to read data */
> +	bool irq_enabled; /* Flag to indicate disable/enable irq sequence */
> +	bool irq_received; /* Flag to indicate that irq is received */
> +	spinlock_t irq_enabled_lock; /* Spin lock for read irq */
> +	unsigned char *tx_buffer; /* Transmit buffer */
> +	unsigned char *rx_buffer; /* Receive buffer */
> +	unsigned int write_count; /* Holds nubers of byte written */
> +	unsigned int read_count; /* Hold nubers of byte read */
> +	struct mutex
> +		sr1xx_access_lock; /* Lock used to synchronize read and write */
> +	size_t total_bytes_to_read; /* Total bytes read from the device */
> +	bool is_extended_len_bit_set; /* Variable to check ext payload Len */
> +	bool read_abort_requested; /* Used to indicate read abort request */
> +	bool is_fw_dwnld_enabled; /* Used to indicate fw download mode */
> +	int mode; /* Indicate write or read mode */
> +	long timeout_in_ms; /* Wait event interrupt timeout in ms */
> +};
> +
> +/* Power enable/disable and read abort ioctl arguments */
> +enum { PWR_DISABLE = 0, PWR_ENABLE, ABORT_READ_PENDING };
> +
> +enum spi_status_codes {
> +	TRANSCEIVE_SUCCESS,
> +	TRANSCEIVE_FAIL,
> +	IRQ_WAIT_REQUEST,
> +	IRQ_WAIT_TIMEOUT
> +};
> +
> +/* Spi write/read operation mode */
> +enum spi_operation_modes { SR1XX_WRITE_MODE, SR1XX_READ_MODE };
> +static int sr1xx_dev_open(struct inode *inode, struct file *filp)
> +{
> +	struct sr1xx_dev *sr1xx_dev = container_of(
> +		filp->private_data, struct sr1xx_dev, sr1xx_device);
> +
> +	filp->private_data = sr1xx_dev;
> +	return 0;
> +}
> +
> +static void sr1xx_disable_irq(struct sr1xx_dev *sr1xx_dev)
> +{
> +	unsigned long flags;
> +
> +	spin_lock_irqsave(&sr1xx_dev->irq_enabled_lock, flags);
> +	if ((sr1xx_dev->irq_enabled)) {
> +		disable_irq_nosync(sr1xx_dev->spi->irq);
> +		sr1xx_dev->irq_received = true;
> +		sr1xx_dev->irq_enabled = false;
> +	}
> +	spin_unlock_irqrestore(&sr1xx_dev->irq_enabled_lock, flags);
> +}
> +
> +static void sr1xx_enable_irq(struct sr1xx_dev *sr1xx_dev)
> +{
> +	unsigned long flags;
> +
> +	spin_lock_irqsave(&sr1xx_dev->irq_enabled_lock, flags);
> +	if (!sr1xx_dev->irq_enabled) {
> +		enable_irq(sr1xx_dev->spi->irq);
> +		sr1xx_dev->irq_enabled = true;
> +		sr1xx_dev->irq_received = false;
> +	}
> +	spin_unlock_irqrestore(&sr1xx_dev->irq_enabled_lock, flags);
> +}
> +
> +static irqreturn_t sr1xx_dev_irq_handler(int irq, void *dev_id)
> +{
> +	struct sr1xx_dev *sr1xx_dev = dev_id;
> +
> +	sr1xx_disable_irq(sr1xx_dev);
> +	/* Wake up waiting readers */
> +	wake_up(&sr1xx_dev->read_wq);
> +	if (device_may_wakeup(&sr1xx_dev->spi->dev))
> +		pm_wakeup_event(&sr1xx_dev->spi->dev, WAKEUP_SRC_TIMEOUT);
> +	return IRQ_HANDLED;
> +}
> +
> +static long sr1xx_dev_ioctl(struct file *filp, unsigned int cmd,
> +			    unsigned long arg)
> +{
> +	int ret = 0;
> +	struct sr1xx_dev *sr1xx_dev = NULL;
> +
> +	sr1xx_dev = filp->private_data;
> +
> +	switch (cmd) {
> +	case SR1XX_SET_PWR:
> +		if (arg == PWR_ENABLE) {
> +			gpio_set_value(sr1xx_dev->ce_gpio, 1);
> +			usleep_range(10000, 12000);
> +		} else if (arg == PWR_DISABLE) {
> +			gpio_set_value(sr1xx_dev->ce_gpio, 0);
> +			sr1xx_disable_irq(sr1xx_dev);
> +			usleep_range(10000, 12000);
> +		} else if (arg == ABORT_READ_PENDING) {
> +			sr1xx_dev->read_abort_requested = true;
> +			sr1xx_disable_irq(sr1xx_dev);
> +			/* Wake up waiting readers */
> +			wake_up(&sr1xx_dev->read_wq);
> +		}
> +		break;
> +	case SR1XX_SET_FWD:
> +		if (arg == 1) {
> +			sr1xx_dev->is_fw_dwnld_enabled = true;
> +			sr1xx_dev->read_abort_requested = false;
> +		} else if (arg == 0) {
> +			sr1xx_dev->is_fw_dwnld_enabled = false;
> +		}
> +		break;
> +	default:
> +		dev_err(&sr1xx_dev->spi->dev, " Error case");
> +		ret = -EINVAL;
> +	}
> +	return ret;
> +}
> +
> +/**
> + * sr1xx_wait_for_irq_gpio_low
> + *
> + * Function to wait till irq gpio goes low state
> + *
> + */
> +void sr1xx_wait_for_irq_gpio_low(struct sr1xx_dev *sr1xx_dev)
> +{
> +	int retry_count = 0;
> +
> +	do {
> +		udelay(10);
> +		retry_count++;
> +		if (retry_count == MAX_RETRY_COUNT_FOR_HANDSHAKE) {
> +			dev_info(&sr1xx_dev->spi->dev,
> +				 "Slave not released the IRQ even after 10ms");
> +			break;
> +		}
> +	} while (gpio_get_value(sr1xx_dev->irq_gpio));
> +}
> +
> +/**
> + * sr1xx_dev_transceive
> + * @op_mode indicates write/read operation
> + *
> + * Write and Read logic implemented under same api with
> + * mutex lock protection so write and read synchronized
> + *
> + * During Uwb ranging sequence(read) need to block write sequence
> + * in order to avoid some race condition scenarios.
> + *
> + * Returns     : Number of bytes write/read if read is success else (-1)
> + *               otherwise indicate each error code
> + */
> +static int sr1xx_dev_transceive(struct sr1xx_dev *sr1xx_dev, int op_mode,
> +				int count)
> +{
> +	int ret, retry_count;
> +
> +	mutex_lock(&sr1xx_dev->sr1xx_access_lock);
> +	sr1xx_dev->mode = op_mode;
> +	sr1xx_dev->total_bytes_to_read = 0;
> +	sr1xx_dev->is_extended_len_bit_set = 0;
> +	ret = -1;
> +	retry_count = 0;
> +
> +	switch (sr1xx_dev->mode) {
> +	case SR1XX_WRITE_MODE: {
> +		sr1xx_dev->write_count = 0;
> +		/* UCI Header write */
> +		ret = spi_write(sr1xx_dev->spi, sr1xx_dev->tx_buffer,
> +				UCI_HEADER_LEN);
> +		if (ret < 0) {
> +			ret = -EIO;
> +			dev_err(&sr1xx_dev->spi->dev,
> +				"spi_write header : Failed.\n");
> +			goto transceive_end;
> +		} else {
> +			count -= UCI_HEADER_LEN;
> +		}
> +		if (count > 0) {
> +			/* In between header write and payload write slave need some time */
> +			usleep_range(30, 50);
> +			/* UCI Payload write */
> +			ret = spi_write(sr1xx_dev->spi,
> +					sr1xx_dev->tx_buffer + UCI_HEADER_LEN,
> +					count);
> +			if (ret < 0) {
> +				ret = -EIO;
> +				dev_err(&sr1xx_dev->spi->dev,
> +					"spi_write payload : Failed.\n");
> +				goto transceive_end;
> +			}
> +		}
> +		sr1xx_dev->write_count = count + UCI_HEADER_LEN;
> +		ret = TRANSCEIVE_SUCCESS;
> +	} break;
> +	case SR1XX_READ_MODE: {
> +		if (!gpio_get_value(sr1xx_dev->irq_gpio)) {
> +			dev_err(&sr1xx_dev->spi->dev,
> +				"IRQ might have gone low due to write ");
> +			ret = IRQ_WAIT_REQUEST;
> +			goto transceive_end;
> +		}
> +		retry_count = 0;
> +		gpio_set_value(sr1xx_dev->spi_handshake_gpio, 1);
> +		while (gpio_get_value(sr1xx_dev->irq_gpio)) {
> +			if (retry_count == MAX_RETRY_COUNT_FOR_IRQ_CHECK)
> +				break;
> +			udelay(10);
> +			retry_count++;
> +		}
> +		sr1xx_enable_irq(sr1xx_dev);
> +		sr1xx_dev->read_count = 0;
> +		retry_count = 0;
> +		/* Wait for inetrrupt upto 500ms */
> +		ret = wait_event_interruptible_timeout(
> +			sr1xx_dev->read_wq, sr1xx_dev->irq_received,
> +			sr1xx_dev->timeout_in_ms);
> +		if (ret == 0) {
> +			dev_err(&sr1xx_dev->spi->dev,
> +				"wait_event_interruptible timeout() : Failed.\n");
> +			ret = IRQ_WAIT_TIMEOUT;
> +			goto transceive_end;
> +		}
> +		if (!gpio_get_value(sr1xx_dev->irq_gpio)) {
> +			dev_err(&sr1xx_dev->spi->dev, "Second IRQ is Low");
> +			ret = -1;
> +			goto transceive_end;
> +		}
> +		ret = spi_read(sr1xx_dev->spi, (void *)sr1xx_dev->rx_buffer,
> +			       UCI_HEADER_LEN);
> +		if (ret < 0) {
> +			dev_err(&sr1xx_dev->spi->dev,
> +				"sr1xx_dev_read: spi read error %d\n ", ret);
> +			goto transceive_end;
> +		}
> +		sr1xx_dev->is_extended_len_bit_set =
> +			(sr1xx_dev->rx_buffer[UCI_EXT_PAYLOAD_LEN_IND_OFFSET] &
> +			 UCI_EXT_PAYLOAD_LEN_IND_OFFSET_MASK);
> +		sr1xx_dev->total_bytes_to_read =
> +			sr1xx_dev->rx_buffer[UCI_PAYLOAD_LEN_OFFSET];
> +		if (sr1xx_dev->is_extended_len_bit_set) {
> +			sr1xx_dev->total_bytes_to_read =
> +				((sr1xx_dev->total_bytes_to_read << 8) |
> +				 sr1xx_dev
> +					 ->rx_buffer[UCI_EXT_PAYLOAD_LEN_OFFSET]);
> +		}
> +		if (sr1xx_dev->total_bytes_to_read >
> +		    (MAX_UCI_PKT_SIZE - UCI_HEADER_LEN)) {
> +			dev_err(&sr1xx_dev->spi->dev,
> +				"Length %d  exceeds the max limit %d....",
> +				(int)sr1xx_dev->total_bytes_to_read,
> +				(int)MAX_UCI_PKT_SIZE);
> +			ret = -1;
> +			goto transceive_end;
> +		}
> +		if (sr1xx_dev->total_bytes_to_read > 0) {
> +			ret = spi_read(
> +				sr1xx_dev->spi,
> +				(void *)(sr1xx_dev->rx_buffer + UCI_HEADER_LEN),
> +				sr1xx_dev->total_bytes_to_read);
> +			if (ret < 0) {
> +				dev_err(&sr1xx_dev->spi->dev,
> +					"sr1xx_dev_read: spi read error.. %d\n ",
> +					ret);
> +				goto transceive_end;
> +			}
> +		}
> +		sr1xx_dev->read_count =
> +			(unsigned int)(sr1xx_dev->total_bytes_to_read +
> +				       UCI_HEADER_LEN);
> +		sr1xx_wait_for_irq_gpio_low(sr1xx_dev);
> +		ret = TRANSCEIVE_SUCCESS;
> +		gpio_set_value(sr1xx_dev->spi_handshake_gpio, 0);
> +	} break;
> +	default:
> +		dev_err(&sr1xx_dev->spi->dev, "invalid operation .....");
> +		break;
> +	}
> +transceive_end:
> +	if (sr1xx_dev->mode == SR1XX_READ_MODE)
> +		gpio_set_value(sr1xx_dev->spi_handshake_gpio, 0);
> +
> +	mutex_unlock(&sr1xx_dev->sr1xx_access_lock);
> +	return ret;
> +}
> +
> +/**
> + * sr1xx_hbci_write
> + *
> + * Used to write hbci(SR1xx BootROM Command Interface) packets
> + * during firmware download sequence.
> + *
> + * Returns: TRANSCEIVE_SUCCESS on success or -1 on fail
> + */
> +static int sr1xx_hbci_write(struct sr1xx_dev *sr1xx_dev, int count)
> +{
> +	int ret;
> +
> +	sr1xx_dev->write_count = 0;
> +	/* HBCI write */
> +	ret = spi_write(sr1xx_dev->spi, sr1xx_dev->tx_buffer, count);
> +	if (ret < 0) {
> +		ret = -EIO;
> +		dev_err(&sr1xx_dev->spi->dev,
> +			"spi_write fw download : Failed.\n");
> +		goto hbci_write_fail;
> +	}
> +	sr1xx_dev->write_count = count;
> +	sr1xx_enable_irq(sr1xx_dev);
> +	ret = TRANSCEIVE_SUCCESS;
> +	return ret;
> +hbci_write_fail:
> +	dev_err(&sr1xx_dev->spi->dev, "%s failed...%d", __func__, ret);
> +	return ret;
> +}
> +
> +static ssize_t sr1xx_dev_write(struct file *filp, const char *buf, size_t count,
> +			       loff_t *offset)
> +{
> +	int ret;
> +	struct sr1xx_dev *sr1xx_dev;
> +
> +	sr1xx_dev = filp->private_data;
> +	if (count > SR1XX_MAX_TX_BUF_SIZE || count > SR1XX_TXBUF_SIZE) {
> +		dev_err(&sr1xx_dev->spi->dev, "%s : Write Size Exceeds\n",
> +			__func__);
> +		ret = -ENOBUFS;
> +		goto write_end;
> +	}
> +	if (copy_from_user(sr1xx_dev->tx_buffer, buf, count)) {
> +		dev_err(&sr1xx_dev->spi->dev,
> +			"%s : failed to copy from user space\n", __func__);
> +		return -EFAULT;
> +	}
> +	if (sr1xx_dev->is_fw_dwnld_enabled)
> +		ret = sr1xx_hbci_write(sr1xx_dev, count);
> +	else
> +		ret = sr1xx_dev_transceive(sr1xx_dev, SR1XX_WRITE_MODE, count);
> +	if (ret == TRANSCEIVE_SUCCESS)
> +		ret = sr1xx_dev->write_count;
> +	else
> +		dev_err(&sr1xx_dev->spi->dev, "write failed......");
> +write_end:
> +	return ret;
> +}
> +
> +/**
> + * sr1xx_hbci_read
> + *
> + * Function used to read data from sr1xx on SPI line
> + * as part of firmware download sequence.
> + *
> + * Returns: Number of bytes read if read is success else (-1)
> + *               otherwise indicate each error code
> + */
> +static ssize_t sr1xx_hbci_read(struct sr1xx_dev *sr1xx_dev, char *buf,
> +			       size_t count)
> +{
> +	int ret = -EIO;
> +
> +	if (count > SR1XX_RXBUF_SIZE) {
> +		dev_err(&sr1xx_dev->spi->dev, "count(%zu) out of range(0-%d)\n",
> +			count, SR1XX_RXBUF_SIZE);
> +		ret = -EINVAL;
> +		goto hbci_fail;
> +	}
> +	/* Wait for inetrrupt upto 500ms */
> +	ret = wait_event_interruptible_timeout(sr1xx_dev->read_wq,
> +					       sr1xx_dev->irq_received,
> +					       sr1xx_dev->timeout_in_ms);
> +	if (ret == 0) {
> +		dev_err(&sr1xx_dev->spi->dev,
> +			"hbci wait_event_interruptible timeout() : Failed.\n");
> +		ret = -1;
> +		goto hbci_fail;
> +	}
> +	if (sr1xx_dev->read_abort_requested) {
> +		sr1xx_dev->read_abort_requested = false;
> +		dev_err(&sr1xx_dev->spi->dev, "HBCI Abort Read pending......");
> +		return ret;
> +	}
> +	if (!gpio_get_value(sr1xx_dev->irq_gpio)) {
> +		dev_err(&sr1xx_dev->spi->dev,
> +			"IRQ is low during firmware download");
> +		goto hbci_fail;
> +	}
> +	ret = spi_read(sr1xx_dev->spi, (void *)sr1xx_dev->rx_buffer, count);
> +	if (ret < 0) {
> +		dev_err(&sr1xx_dev->spi->dev,
> +			"sr1xx_dev_read: spi read error %d\n ", ret);
> +		goto hbci_fail;
> +	}
> +	ret = count;
> +	if (copy_to_user(buf, sr1xx_dev->rx_buffer, count)) {
> +		dev_err(&sr1xx_dev->spi->dev,
> +			"sr1xx_dev_read: copy to user failed\n");
> +		ret = -EFAULT;
> +	}
> +	return ret;
> +hbci_fail:
> +	dev_err(&sr1xx_dev->spi->dev, "Error sr1xx_fw_download ret %d Exit\n",
> +		ret);
> +	return ret;
> +}
> +
> +static ssize_t sr1xx_dev_read(struct file *filp, char *buf, size_t count,
> +			      loff_t *offset)
> +{
> +	struct sr1xx_dev *sr1xx_dev = filp->private_data;
> +	int ret = -EIO;
> +
> +	/* 500ms timeout in jiffies */
> +	sr1xx_dev->timeout_in_ms = ((500 * HZ) / 1000);
> +	memset(sr1xx_dev->rx_buffer, 0x00, SR1XX_RXBUF_SIZE);
> +	if (!gpio_get_value(sr1xx_dev->irq_gpio)) {
> +		if (filp->f_flags & O_NONBLOCK) {
> +			ret = -EAGAIN;
> +			goto read_end;
> +		}
> +	}
> +	/* HBCI packet read */
> +	if (sr1xx_dev->is_fw_dwnld_enabled)
> +		return sr1xx_hbci_read(sr1xx_dev, buf, count);
> +	/* UCI packet read */
> +first_irq_wait:
> +	sr1xx_enable_irq(sr1xx_dev);
> +	if (!sr1xx_dev->read_abort_requested) {
> +		ret = wait_event_interruptible(sr1xx_dev->read_wq,
> +					       sr1xx_dev->irq_received);
> +		if (ret) {
> +			dev_err(&sr1xx_dev->spi->dev,
> +				"wait_event_interruptible() : Failed.\n");
> +			goto read_end;
> +		}
> +	}
> +	if (sr1xx_dev->read_abort_requested) {
> +		sr1xx_dev->read_abort_requested = false;
> +		dev_err(&sr1xx_dev->spi->dev, "Abort Read pending......");
> +		return ret;
> +	}
> +	ret = sr1xx_dev_transceive(sr1xx_dev, SR1XX_READ_MODE, count);
> +	if (ret == TRANSCEIVE_SUCCESS) {
> +		if (copy_to_user(buf, sr1xx_dev->rx_buffer,
> +				 sr1xx_dev->read_count)) {
> +			dev_err(&sr1xx_dev->spi->dev,
> +				"%s: copy to user failed\n", __func__);
> +			ret = -EFAULT;
> +			goto read_end;
> +		}
> +		ret = sr1xx_dev->read_count;
> +	} else if (ret == IRQ_WAIT_REQUEST) {
> +		dev_err(&sr1xx_dev->spi->dev,
> +			"Irg is low due to write hence irq is requested again...");
> +		goto first_irq_wait;
> +	} else if (ret == IRQ_WAIT_TIMEOUT) {
> +		dev_err(&sr1xx_dev->spi->dev,
> +			"Second irq is not received..Time out...");
> +		ret = -1;
> +	} else {
> +		dev_err(&sr1xx_dev->spi->dev, "spi read failed...%d", ret);
> +		ret = -1;
> +	}
> +read_end:
> +	return ret;
> +}
> +
> +static int sr1xx_hw_setup(struct device *dev,
> +			  struct sr1xx_spi_platform_data *platform_data)
> +{
> +	int ret;
> +
> +	ret = gpio_request(platform_data->irq_gpio, "sr1xx irq");
> +	if (ret < 0) {
> +		dev_err(dev, "gpio request failed gpio = 0x%x\n",
> +			platform_data->irq_gpio);
> +		goto fail;
> +	}
> +
> +	ret = gpio_direction_input(platform_data->irq_gpio);
> +	if (ret < 0) {
> +		dev_err(dev, "gpio request failed gpio = 0x%x\n",
> +			platform_data->irq_gpio);
> +		goto fail_irq;
> +	}
> +
> +	ret = gpio_request(platform_data->ce_gpio, "sr1xx ce");
> +	if (ret < 0) {
> +		dev_err(dev, "gpio request failed gpio = 0x%x\n",
> +			platform_data->ce_gpio);
> +		goto fail_gpio;
> +	}
> +
> +	ret = gpio_direction_output(platform_data->ce_gpio, 0);
> +	if (ret < 0) {
> +		dev_err(dev, "sr1xx - Failed setting ce gpio - %d\n",

Here and below. Is "sr1xx -" needed in this dev_err()?
The messages in this function don't have consistent wording.

> +			platform_data->ce_gpio);
> +		goto fail_ce_gpio;
> +	}
> +
> +	ret = gpio_request(platform_data->spi_handshake_gpio, "sr1xx ri");
> +	if (ret < 0) {
> +		dev_err(dev, "sr1xx - Failed requesting ri gpio - %d\n",

'ri'?

> +			platform_data->spi_handshake_gpio);
> +		goto fail_gpio;
> +	}
> +
> +	ret = gpio_direction_output(platform_data->spi_handshake_gpio, 0);
> +	if (ret < 0) {
> +		dev_err(dev,
> +			"sr1xx - Failed setting spi handeshake gpio - %d\n",
> +			platform_data->spi_handshake_gpio);
> +		goto fail_handshake_gpio;
> +	}
> +
> +	ret = 0;

No need for this line. 'ret' is kown to be 0 here.
'return 0;' would be even more explicit.

> +	return ret;
> +
> +fail_gpio:
> +fail_handshake_gpio:
> +	gpio_free(platform_data->spi_handshake_gpio);
> +fail_ce_gpio:
> +	gpio_free(platform_data->ce_gpio);
> +fail_irq:
> +	gpio_free(platform_data->irq_gpio);

These gpio_free() are also called in sr1xx_gpio_cleanup() that will be 
called if sr1xx_hw_setup() fails.

> +fail:
> +	dev_err(dev, "%s failed\n", __func__);
> +	return ret;
> +}
> +
> +static inline void sr1xx_set_data(struct spi_device *spi, void *data)
> +{
> +	dev_set_drvdata(&spi->dev, data);
> +}
> +
> +static inline void *sr1xx_get_data(const struct spi_device *spi)
> +{
> +	return dev_get_drvdata(&spi->dev);
> +}
> +
> +/* Possible fops on the sr1xx device */
> +static const struct file_operations sr1xx_dev_fops = {
> +	.owner = THIS_MODULE,
> +	.read = sr1xx_dev_read,
> +	.write = sr1xx_dev_write,
> +	.open = sr1xx_dev_open,
> +	.unlocked_ioctl = sr1xx_dev_ioctl,
> +};
> +
> +static int sr1xx_parse_dt(struct device *dev,
> +			  struct sr1xx_spi_platform_data *pdata)
> +{
> +	struct device_node *np = dev->of_node;
> +
> +	pdata->irq_gpio = of_get_named_gpio(np, "nxp,sr1xx-irq", 0);
> +	if (!gpio_is_valid(pdata->irq_gpio))
> +		return -EINVAL;
> +	pdata->ce_gpio = of_get_named_gpio(np, "nxp,sr1xx-ce", 0);
> +	if (!gpio_is_valid(pdata->ce_gpio))
> +		return -EINVAL;
> +	pdata->spi_handshake_gpio = of_get_named_gpio(np, "nxp,sr1xx-ri", 0);
> +	if (!gpio_is_valid(pdata->spi_handshake_gpio))
> +		return -EINVAL;

Maybe the 3 !gpio_is_valid() should be performed all at one, to make 
sure that the 3 gpio have correct or error values. Otherwise the error 
handling path looks odd.
See comment below.

> +	dev_info(
> +		dev,
You an easily save 1 LoC here :)

> +		"sr1xx : irq_gpio = %d, ce_gpio = %d, spi_handshake_gpio = %d\n",

Is 'sr1xx' needed here. Should'nt dev_info() already prefix with 
something useful?

> +		pdata->irq_gpio, pdata->ce_gpio, pdata->spi_handshake_gpio);
> +	return 0;
> +}
> +
> +/**
> + * sr1xx_gpio_cleanup
> + *
> + * Release requested gpios
> + *
> + */
> +static void sr1xx_gpio_cleanup(struct sr1xx_spi_platform_data *pdata)
> +{
> +	if (gpio_is_valid(pdata->spi_handshake_gpio))
> +		gpio_free(pdata->spi_handshake_gpio);
> +	if (gpio_is_valid(pdata->ce_gpio))
> +		gpio_free(pdata->ce_gpio);
> +	if (gpio_is_valid(pdata->irq_gpio))
> +		gpio_free(pdata->irq_gpio);
> +}
> +
> +static int sr1xx_probe(struct spi_device *spi)
> +{
> +	int ret;
> +	struct sr1xx_spi_platform_data *platform_data = NULL;

Do you really need these 2 variables?
Looks correct to me, but
	struct sr1xx_spi_platform_data platform_data;
and '&platform_data' in the code blow would be enough?
(No strong opinion about it)

> +	struct sr1xx_spi_platform_data platform_data1;

'platform_data1' is not initialized here, so...

> +	struct sr1xx_dev *sr1xx_dev = NULL;
> +	unsigned int irq_flags;
> +
> +	dev_info(&spi->dev, "%s chip select : %d , bus number = %d\n", __func__,
> +		 spi->chip_select, spi->master->bus_num);
> +
> +	ret = sr1xx_parse_dt(&spi->dev, &platform_data1);
> +	if (ret) {
> +		dev_err(&spi->dev, "%s - Failed to parse DT\n", __func__);

... if sr1xx_parse_dt() fails, the gpio values can be anything when 
sr1xx_gpio_cleanup() is called in the error handling path.
Zeroing the structure is maybe not enough. 0 looks to be a valid value 
that will no be matched by the gpio_is_valid() calls in 
sr1xx_gpio_cleanup().

> +		goto err_exit;
> +	}
> +	platform_data = &platform_data1;
> +
> +	sr1xx_dev = kzalloc(sizeof(*sr1xx_dev), GFP_KERNEL);
> +	if (sr1xx_dev == NULL) {

!sr1xx_dev is less verbose.

> +		ret = -ENOMEM;
> +		goto err_exit;
> +	}
> +	ret = sr1xx_hw_setup(&spi->dev, platform_data);
> +	if (ret < 0) {
> +		dev_err(&spi->dev, "Failed to sr1xx_enable_SR1XX_IRQ_ENABLE\n");
> +		goto err_setup;
> +	}
> +
> +	spi->bits_per_word = 8;
> +	spi->mode = SPI_MODE_0;
> +	spi->max_speed_hz = SR1XX_SPI_CLOCK;
> +	ret = spi_setup(spi);
> +	if (ret < 0) {
> +		dev_err(&spi->dev, "failed to do spi_setup()\n");
> +		goto err_setup;
> +	}
> +
> +	sr1xx_dev->spi = spi;
> +	sr1xx_dev->sr1xx_device.minor = MISC_DYNAMIC_MINOR;
> +	sr1xx_dev->sr1xx_device.name = "sr1xx";
> +	sr1xx_dev->sr1xx_device.fops = &sr1xx_dev_fops;
> +	sr1xx_dev->sr1xx_device.parent = &spi->dev;
> +	sr1xx_dev->irq_gpio = platform_data->irq_gpio;
> +	sr1xx_dev->ce_gpio = platform_data->ce_gpio;
> +	sr1xx_dev->spi_handshake_gpio = platform_data->spi_handshake_gpio;
> +
> +	dev_set_drvdata(&spi->dev, sr1xx_dev);
> +
> +	/* init mutex and queues */
> +	init_waitqueue_head(&sr1xx_dev->read_wq);
> +	mutex_init(&sr1xx_dev->sr1xx_access_lock);
> +
> +	spin_lock_init(&sr1xx_dev->irq_enabled_lock);
> +
> +	ret = misc_register(&sr1xx_dev->sr1xx_device);
> +	if (ret < 0) {
> +		dev_err(&spi->dev, "misc_register failed! %d\n", ret);
> +		goto err_setup;
> +	}
> +
> +	sr1xx_dev->tx_buffer = kzalloc(SR1XX_TXBUF_SIZE, GFP_KERNEL);
> +	sr1xx_dev->rx_buffer = kzalloc(SR1XX_RXBUF_SIZE, GFP_KERNEL);
> +	if (sr1xx_dev->tx_buffer == NULL) {

!sr1xx_dev->tx_buffer is less verbove.
This kzalloc() is not freed in the error handling path of the probe.

> +		ret = -ENOMEM;
> +		goto exit_free_dev;
> +	}
> +	if (sr1xx_dev->rx_buffer == NULL) {

!sr1xx_dev->rx_buffer is less verbove.
This kzalloc() is not freed in the error handling path of the probe.

> +		ret = -ENOMEM;
> +		goto exit_free_dev;
> +	}
> +
> +	sr1xx_dev->spi->irq = gpio_to_irq(platform_data->irq_gpio);
> +

This empty line is not needed.

> +	if (sr1xx_dev->spi->irq < 0) {
> +		dev_err(&spi->dev, "gpio_to_irq request failed gpio = 0x%x\n",
> +			platform_data->irq_gpio);
> +		goto err_irq_request;
> +	}
> +	/* request irq. The irq is set whenever the chip has data available
> +	 * for reading. It is cleared when all data has been read.
> +	 */
> +	irq_flags = IRQ_TYPE_LEVEL_HIGH;
> +	sr1xx_dev->irq_enabled = true;
> +	sr1xx_dev->irq_received = false;
> +
> +	ret = request_irq(sr1xx_dev->spi->irq, sr1xx_dev_irq_handler, irq_flags,
> +			  sr1xx_dev->sr1xx_device.name, sr1xx_dev);
> +	if (ret) {
> +		dev_err(&spi->dev, "request_irq failed\n");
> +		goto err_irq_request;
> +	}
> +	sr1xx_disable_irq(sr1xx_dev);
> +	return ret;

'return 0;' to make things mor explicit?

> +err_irq_request:
> +exit_free_dev:
> +	if (sr1xx_dev != NULL) {

can 'sr1xx_dev' be NULL here?

> +		kfree(sr1xx_dev->tx_buffer);
> +		kfree(sr1xx_dev->rx_buffer);
> +		misc_deregister(&sr1xx_dev->sr1xx_device);
> +	}
> +err_setup:
> +	if (sr1xx_dev != NULL)

can 'sr1xx_dev' be NULL here?

> +		mutex_destroy(&sr1xx_dev->sr1xx_access_lock);
> +err_exit:
> +	sr1xx_gpio_cleanup(platform_data);
> +	kfree(sr1xx_dev);
> +	dev_err(&spi->dev, "ERROR: Exit : %s ret %d\n", __func__, ret);
> +	return ret;
> +}
> +
> +static void sr1xx_remove(struct spi_device *spi)
> +{
> +	struct sr1xx_dev *sr1xx_dev = sr1xx_get_data(spi);
> +
> +	gpio_free(sr1xx_dev->ce_gpio);
> +	mutex_destroy(&sr1xx_dev->sr1xx_access_lock);
> +	free_irq(sr1xx_dev->spi->irq, sr1xx_dev);
> +	gpio_free(sr1xx_dev->irq_gpio);
> +	gpio_free(sr1xx_dev->spi_handshake_gpio);

sr1xx_gpio_cleanup() instead of the 3 gpio_free()?

> +	misc_deregister(&sr1xx_dev->sr1xx_device);
> +	if (sr1xx_dev != NULL) {

can 'sr1xx_dev' be NULL here?

> +		kfree(sr1xx_dev->tx_buffer);
> +		kfree(sr1xx_dev->rx_buffer);
> +		kfree(sr1xx_dev);
> +	}
> +}
> +
> +/**
> + * sr1xx_dev_suspend
> + *
> + * Executed before putting the system into a sleep state
> + *
> + */
> +int sr1xx_dev_suspend(struct device *dev)
> +{
> +	struct sr1xx_dev *sr1xx_dev = dev_get_drvdata(dev);
> +
> +	if (device_may_wakeup(dev))
> +		disable_irq_wake(sr1xx_dev->spi->irq);
> +	return 0;
> +}
> +
> +/**
> + * sr1xx_dev_resume
> + *
> + * Executed after waking the system up from a sleep state
> + *
> + */

No need for an empty line here.

> +
> +int sr1xx_dev_resume(struct device *dev)
> +{
> +	struct sr1xx_dev *sr1xx_dev = dev_get_drvdata(dev);
> +
> +	if (device_may_wakeup(dev))
> +		enable_irq_wake(sr1xx_dev->spi->irq);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id sr1xx_dt_match[] = {
> +	{
> +		.compatible = "nxp,sr1xx",
> +	},
> +	{}
> +};
> +
> +static const struct dev_pm_ops sr1xx_dev_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(
> +	sr1xx_dev_suspend, sr1xx_dev_resume) };
> +
> +static struct spi_driver sr1xx_driver = {
> +	.driver = {
> +		   .name = "sr1xx",
> +		   .pm = &sr1xx_dev_pm_ops,
> +		   .bus = &spi_bus_type,
> +		   .owner = THIS_MODULE,
> +		   .of_match_table = sr1xx_dt_match,
> +		    },
> +	.probe = sr1xx_probe,
> +	.remove = sr1xx_remove,
> +};
> +
> +static int __init sr1xx_dev_init(void)
> +{
> +	return spi_register_driver(&sr1xx_driver);
> +}
> +
> +module_init(sr1xx_dev_init);
> +
> +static void __exit sr1xx_dev_exit(void)
> +{
> +	spi_unregister_driver(&sr1xx_driver);
> +}
> +
> +module_exit(sr1xx_dev_exit);
> +
> +MODULE_AUTHOR("Manjunatha Venkatesh <manjunatha.venkatesh-3arQi8VN3Tc@public.gmane.org>");
> +MODULE_DESCRIPTION("NXP SR1XX SPI driver");
> +MODULE_LICENSE("GPL");
Greg Kroah-Hartman June 2, 2022, 8:24 a.m. UTC | #4
On Sat, May 28, 2022 at 12:13:51AM +0530, Manjunatha Venkatesh wrote:
> Ultra-wideband (UWB) is a short-range wireless communication protocol.
> 
> NXP has SR1XX family of UWB Subsystems (UWBS) devices. SR1XX SOCs
> are FiRa Compliant. SR1XX SOCs are flash less devices and they need
> Firmware Download on every device boot. More details on the SR1XX Family
> can be found at https://www.nxp.com/products/:UWB-TRIMENSION
> 
> The sr1xx driver work the SR1XX Family of UWBS, and uses UWB Controller
> Interface (UCI).  The corresponding details are available in the FiRa
> Consortium Website (https://www.firaconsortium.org/).
> 
> Internally driver will handle two modes of operation.
> 1.HBCI mode (sr1xx BootROM Code Interface)
> Firmware download uses HBCI ptotocol packet structure which is
> Nxp proprietary,Firmware File(.bin) stored in user space context
> and during device init sequence pick the firmware packet in chunk
> and send it to the driver with write() api call.
> 
> After the firmware download sequence at the end UWBS will
> send device status notification and its indication of device entered
> UCI mode.
> Here after any command/response/notification will follow
> UCI packet structure.
> 
> 2.UCI mode (UWB Command interface)
> Once Firmware download finishes sr1xx will switch to UCI mode.
> Then driver exchange command/response/notification as per the FIRA UCI
> standard format between user space and sr1xx device.
> Any response or notification received from sr1xx through SPI line
> will convey to user space.
> 
> Its Interrupt based driver and IO Handshake needed with SR1XX Family of
> SOCs.
> This driver needs dts config update as per the sr1xx data sheet.
> Corresponding document available in Documentation/devicetree/bindings/uwb
> 
> Message-ID: <20220504171337.3416983-1-manjunatha.venkatesh@nxp.com>
> Signed-off-by: Manjunatha Venkatesh <manjunatha.venkatesh@nxp.com>
> ---
> Changes since v3:
>   - Commit Message Description updated
>   - Renamed file from sr1xx.c to nxp-sr1xx.c
>   - Removed unwanted header files
>   - Removed sr1xx.h file since its not required for single source file

For some reason you seem to have ignored many of my review requests of
your previous submission.  Because of that, I'll just drop this series
and wait for a version that addresses those issues as they are still
present here, making this submission impossible to accept.

thanks,

greg k-h
diff mbox series

Patch

diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index 41d2bb0ae23a..4f81d5758940 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -483,6 +483,18 @@  config OPEN_DICE
 
 	  If unsure, say N.
 
+config NXP_UWB
+        tristate "Nxp UCI(Uwb Command Interface) protocol driver support"
+        depends on SPI
+        help
+        This option enables the UWB driver for Nxp sr1xx
+        device. Such device supports UCI packet structure,
+        FiRa compliant.
+
+        Say Y here to compile support for sr1xx into the kernel or
+        say M to compile it as a module. The module will be called
+        sr1xx.ko
+
 source "drivers/misc/c2port/Kconfig"
 source "drivers/misc/eeprom/Kconfig"
 source "drivers/misc/cb710/Kconfig"
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index 70e800e9127f..d4e6e4f1ec29 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -60,3 +60,4 @@  obj-$(CONFIG_XILINX_SDFEC)	+= xilinx_sdfec.o
 obj-$(CONFIG_HISI_HIKEY_USB)	+= hisi_hikey_usb.o
 obj-$(CONFIG_HI6421V600_IRQ)	+= hi6421v600-irq.o
 obj-$(CONFIG_OPEN_DICE)		+= open-dice.o
+obj-$(CONFIG_NXP_UWB) 		+= nxp-sr1xx.o
diff --git a/drivers/misc/nxp-sr1xx.c b/drivers/misc/nxp-sr1xx.c
new file mode 100644
index 000000000000..25648712a61b
--- /dev/null
+++ b/drivers/misc/nxp-sr1xx.c
@@ -0,0 +1,834 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * SPI driver for UWB SR1xx
+ * Copyright (C) 2018-2022 NXP.
+ *
+ * Author: Manjunatha Venkatesh <manjunatha.venkatesh@nxp.com>
+ */
+#include <linux/miscdevice.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/of_gpio.h>
+#include <linux/spi/spi.h>
+
+#define SR1XX_MAGIC 0xEA
+#define SR1XX_SET_PWR _IOW(SR1XX_MAGIC, 0x01, long)
+#define SR1XX_SET_FWD _IOW(SR1XX_MAGIC, 0x02, long)
+
+#define UCI_HEADER_LEN 4
+#define HBCI_HEADER_LEN 4
+#define UCI_PAYLOAD_LEN_OFFSET 3
+
+#define UCI_EXT_PAYLOAD_LEN_IND_OFFSET 1
+#define UCI_EXT_PAYLOAD_LEN_IND_OFFSET_MASK 0x80
+#define UCI_EXT_PAYLOAD_LEN_OFFSET 2
+
+#define SR1XX_TXBUF_SIZE 4200
+#define SR1XX_RXBUF_SIZE 4200
+#define SR1XX_MAX_TX_BUF_SIZE 4200
+
+#define MAX_RETRY_COUNT_FOR_IRQ_CHECK 100
+#define MAX_RETRY_COUNT_FOR_HANDSHAKE 1000
+
+/* Macro to define SPI clock frequency */
+#define SR1XX_SPI_CLOCK 16000000L
+#define WAKEUP_SRC_TIMEOUT (2000)
+
+/* Maximum UCI packet size supported from the driver */
+#define MAX_UCI_PKT_SIZE 4200
+
+struct sr1xx_spi_platform_data {
+	unsigned int irq_gpio; /* SR1XX will interrupt host for any ntf */
+	unsigned int ce_gpio; /* SW reset gpio */
+	unsigned int spi_handshake_gpio; /* Host ready to read data */
+};
+
+/* Device specific macro and structure */
+struct sr1xx_dev {
+	wait_queue_head_t read_wq; /* Wait queue for read interrupt */
+	struct spi_device *spi; /* Spi device structure */
+	struct miscdevice sr1xx_device; /* Char device as misc driver */
+	unsigned int ce_gpio; /* SW reset gpio */
+	unsigned int irq_gpio; /* SR1XX will interrupt host for any ntf */
+	unsigned int spi_handshake_gpio; /* Host ready to read data */
+	bool irq_enabled; /* Flag to indicate disable/enable irq sequence */
+	bool irq_received; /* Flag to indicate that irq is received */
+	spinlock_t irq_enabled_lock; /* Spin lock for read irq */
+	unsigned char *tx_buffer; /* Transmit buffer */
+	unsigned char *rx_buffer; /* Receive buffer */
+	unsigned int write_count; /* Holds nubers of byte written */
+	unsigned int read_count; /* Hold nubers of byte read */
+	struct mutex
+		sr1xx_access_lock; /* Lock used to synchronize read and write */
+	size_t total_bytes_to_read; /* Total bytes read from the device */
+	bool is_extended_len_bit_set; /* Variable to check ext payload Len */
+	bool read_abort_requested; /* Used to indicate read abort request */
+	bool is_fw_dwnld_enabled; /* Used to indicate fw download mode */
+	int mode; /* Indicate write or read mode */
+	long timeout_in_ms; /* Wait event interrupt timeout in ms */
+};
+
+/* Power enable/disable and read abort ioctl arguments */
+enum { PWR_DISABLE = 0, PWR_ENABLE, ABORT_READ_PENDING };
+
+enum spi_status_codes {
+	TRANSCEIVE_SUCCESS,
+	TRANSCEIVE_FAIL,
+	IRQ_WAIT_REQUEST,
+	IRQ_WAIT_TIMEOUT
+};
+
+/* Spi write/read operation mode */
+enum spi_operation_modes { SR1XX_WRITE_MODE, SR1XX_READ_MODE };
+static int sr1xx_dev_open(struct inode *inode, struct file *filp)
+{
+	struct sr1xx_dev *sr1xx_dev = container_of(
+		filp->private_data, struct sr1xx_dev, sr1xx_device);
+
+	filp->private_data = sr1xx_dev;
+	return 0;
+}
+
+static void sr1xx_disable_irq(struct sr1xx_dev *sr1xx_dev)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&sr1xx_dev->irq_enabled_lock, flags);
+	if ((sr1xx_dev->irq_enabled)) {
+		disable_irq_nosync(sr1xx_dev->spi->irq);
+		sr1xx_dev->irq_received = true;
+		sr1xx_dev->irq_enabled = false;
+	}
+	spin_unlock_irqrestore(&sr1xx_dev->irq_enabled_lock, flags);
+}
+
+static void sr1xx_enable_irq(struct sr1xx_dev *sr1xx_dev)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&sr1xx_dev->irq_enabled_lock, flags);
+	if (!sr1xx_dev->irq_enabled) {
+		enable_irq(sr1xx_dev->spi->irq);
+		sr1xx_dev->irq_enabled = true;
+		sr1xx_dev->irq_received = false;
+	}
+	spin_unlock_irqrestore(&sr1xx_dev->irq_enabled_lock, flags);
+}
+
+static irqreturn_t sr1xx_dev_irq_handler(int irq, void *dev_id)
+{
+	struct sr1xx_dev *sr1xx_dev = dev_id;
+
+	sr1xx_disable_irq(sr1xx_dev);
+	/* Wake up waiting readers */
+	wake_up(&sr1xx_dev->read_wq);
+	if (device_may_wakeup(&sr1xx_dev->spi->dev))
+		pm_wakeup_event(&sr1xx_dev->spi->dev, WAKEUP_SRC_TIMEOUT);
+	return IRQ_HANDLED;
+}
+
+static long sr1xx_dev_ioctl(struct file *filp, unsigned int cmd,
+			    unsigned long arg)
+{
+	int ret = 0;
+	struct sr1xx_dev *sr1xx_dev = NULL;
+
+	sr1xx_dev = filp->private_data;
+
+	switch (cmd) {
+	case SR1XX_SET_PWR:
+		if (arg == PWR_ENABLE) {
+			gpio_set_value(sr1xx_dev->ce_gpio, 1);
+			usleep_range(10000, 12000);
+		} else if (arg == PWR_DISABLE) {
+			gpio_set_value(sr1xx_dev->ce_gpio, 0);
+			sr1xx_disable_irq(sr1xx_dev);
+			usleep_range(10000, 12000);
+		} else if (arg == ABORT_READ_PENDING) {
+			sr1xx_dev->read_abort_requested = true;
+			sr1xx_disable_irq(sr1xx_dev);
+			/* Wake up waiting readers */
+			wake_up(&sr1xx_dev->read_wq);
+		}
+		break;
+	case SR1XX_SET_FWD:
+		if (arg == 1) {
+			sr1xx_dev->is_fw_dwnld_enabled = true;
+			sr1xx_dev->read_abort_requested = false;
+		} else if (arg == 0) {
+			sr1xx_dev->is_fw_dwnld_enabled = false;
+		}
+		break;
+	default:
+		dev_err(&sr1xx_dev->spi->dev, " Error case");
+		ret = -EINVAL;
+	}
+	return ret;
+}
+
+/**
+ * sr1xx_wait_for_irq_gpio_low
+ *
+ * Function to wait till irq gpio goes low state
+ *
+ */
+void sr1xx_wait_for_irq_gpio_low(struct sr1xx_dev *sr1xx_dev)
+{
+	int retry_count = 0;
+
+	do {
+		udelay(10);
+		retry_count++;
+		if (retry_count == MAX_RETRY_COUNT_FOR_HANDSHAKE) {
+			dev_info(&sr1xx_dev->spi->dev,
+				 "Slave not released the IRQ even after 10ms");
+			break;
+		}
+	} while (gpio_get_value(sr1xx_dev->irq_gpio));
+}
+
+/**
+ * sr1xx_dev_transceive
+ * @op_mode indicates write/read operation
+ *
+ * Write and Read logic implemented under same api with
+ * mutex lock protection so write and read synchronized
+ *
+ * During Uwb ranging sequence(read) need to block write sequence
+ * in order to avoid some race condition scenarios.
+ *
+ * Returns     : Number of bytes write/read if read is success else (-1)
+ *               otherwise indicate each error code
+ */
+static int sr1xx_dev_transceive(struct sr1xx_dev *sr1xx_dev, int op_mode,
+				int count)
+{
+	int ret, retry_count;
+
+	mutex_lock(&sr1xx_dev->sr1xx_access_lock);
+	sr1xx_dev->mode = op_mode;
+	sr1xx_dev->total_bytes_to_read = 0;
+	sr1xx_dev->is_extended_len_bit_set = 0;
+	ret = -1;
+	retry_count = 0;
+
+	switch (sr1xx_dev->mode) {
+	case SR1XX_WRITE_MODE: {
+		sr1xx_dev->write_count = 0;
+		/* UCI Header write */
+		ret = spi_write(sr1xx_dev->spi, sr1xx_dev->tx_buffer,
+				UCI_HEADER_LEN);
+		if (ret < 0) {
+			ret = -EIO;
+			dev_err(&sr1xx_dev->spi->dev,
+				"spi_write header : Failed.\n");
+			goto transceive_end;
+		} else {
+			count -= UCI_HEADER_LEN;
+		}
+		if (count > 0) {
+			/* In between header write and payload write slave need some time */
+			usleep_range(30, 50);
+			/* UCI Payload write */
+			ret = spi_write(sr1xx_dev->spi,
+					sr1xx_dev->tx_buffer + UCI_HEADER_LEN,
+					count);
+			if (ret < 0) {
+				ret = -EIO;
+				dev_err(&sr1xx_dev->spi->dev,
+					"spi_write payload : Failed.\n");
+				goto transceive_end;
+			}
+		}
+		sr1xx_dev->write_count = count + UCI_HEADER_LEN;
+		ret = TRANSCEIVE_SUCCESS;
+	} break;
+	case SR1XX_READ_MODE: {
+		if (!gpio_get_value(sr1xx_dev->irq_gpio)) {
+			dev_err(&sr1xx_dev->spi->dev,
+				"IRQ might have gone low due to write ");
+			ret = IRQ_WAIT_REQUEST;
+			goto transceive_end;
+		}
+		retry_count = 0;
+		gpio_set_value(sr1xx_dev->spi_handshake_gpio, 1);
+		while (gpio_get_value(sr1xx_dev->irq_gpio)) {
+			if (retry_count == MAX_RETRY_COUNT_FOR_IRQ_CHECK)
+				break;
+			udelay(10);
+			retry_count++;
+		}
+		sr1xx_enable_irq(sr1xx_dev);
+		sr1xx_dev->read_count = 0;
+		retry_count = 0;
+		/* Wait for inetrrupt upto 500ms */
+		ret = wait_event_interruptible_timeout(
+			sr1xx_dev->read_wq, sr1xx_dev->irq_received,
+			sr1xx_dev->timeout_in_ms);
+		if (ret == 0) {
+			dev_err(&sr1xx_dev->spi->dev,
+				"wait_event_interruptible timeout() : Failed.\n");
+			ret = IRQ_WAIT_TIMEOUT;
+			goto transceive_end;
+		}
+		if (!gpio_get_value(sr1xx_dev->irq_gpio)) {
+			dev_err(&sr1xx_dev->spi->dev, "Second IRQ is Low");
+			ret = -1;
+			goto transceive_end;
+		}
+		ret = spi_read(sr1xx_dev->spi, (void *)sr1xx_dev->rx_buffer,
+			       UCI_HEADER_LEN);
+		if (ret < 0) {
+			dev_err(&sr1xx_dev->spi->dev,
+				"sr1xx_dev_read: spi read error %d\n ", ret);
+			goto transceive_end;
+		}
+		sr1xx_dev->is_extended_len_bit_set =
+			(sr1xx_dev->rx_buffer[UCI_EXT_PAYLOAD_LEN_IND_OFFSET] &
+			 UCI_EXT_PAYLOAD_LEN_IND_OFFSET_MASK);
+		sr1xx_dev->total_bytes_to_read =
+			sr1xx_dev->rx_buffer[UCI_PAYLOAD_LEN_OFFSET];
+		if (sr1xx_dev->is_extended_len_bit_set) {
+			sr1xx_dev->total_bytes_to_read =
+				((sr1xx_dev->total_bytes_to_read << 8) |
+				 sr1xx_dev
+					 ->rx_buffer[UCI_EXT_PAYLOAD_LEN_OFFSET]);
+		}
+		if (sr1xx_dev->total_bytes_to_read >
+		    (MAX_UCI_PKT_SIZE - UCI_HEADER_LEN)) {
+			dev_err(&sr1xx_dev->spi->dev,
+				"Length %d  exceeds the max limit %d....",
+				(int)sr1xx_dev->total_bytes_to_read,
+				(int)MAX_UCI_PKT_SIZE);
+			ret = -1;
+			goto transceive_end;
+		}
+		if (sr1xx_dev->total_bytes_to_read > 0) {
+			ret = spi_read(
+				sr1xx_dev->spi,
+				(void *)(sr1xx_dev->rx_buffer + UCI_HEADER_LEN),
+				sr1xx_dev->total_bytes_to_read);
+			if (ret < 0) {
+				dev_err(&sr1xx_dev->spi->dev,
+					"sr1xx_dev_read: spi read error.. %d\n ",
+					ret);
+				goto transceive_end;
+			}
+		}
+		sr1xx_dev->read_count =
+			(unsigned int)(sr1xx_dev->total_bytes_to_read +
+				       UCI_HEADER_LEN);
+		sr1xx_wait_for_irq_gpio_low(sr1xx_dev);
+		ret = TRANSCEIVE_SUCCESS;
+		gpio_set_value(sr1xx_dev->spi_handshake_gpio, 0);
+	} break;
+	default:
+		dev_err(&sr1xx_dev->spi->dev, "invalid operation .....");
+		break;
+	}
+transceive_end:
+	if (sr1xx_dev->mode == SR1XX_READ_MODE)
+		gpio_set_value(sr1xx_dev->spi_handshake_gpio, 0);
+
+	mutex_unlock(&sr1xx_dev->sr1xx_access_lock);
+	return ret;
+}
+
+/**
+ * sr1xx_hbci_write
+ *
+ * Used to write hbci(SR1xx BootROM Command Interface) packets
+ * during firmware download sequence.
+ *
+ * Returns: TRANSCEIVE_SUCCESS on success or -1 on fail
+ */
+static int sr1xx_hbci_write(struct sr1xx_dev *sr1xx_dev, int count)
+{
+	int ret;
+
+	sr1xx_dev->write_count = 0;
+	/* HBCI write */
+	ret = spi_write(sr1xx_dev->spi, sr1xx_dev->tx_buffer, count);
+	if (ret < 0) {
+		ret = -EIO;
+		dev_err(&sr1xx_dev->spi->dev,
+			"spi_write fw download : Failed.\n");
+		goto hbci_write_fail;
+	}
+	sr1xx_dev->write_count = count;
+	sr1xx_enable_irq(sr1xx_dev);
+	ret = TRANSCEIVE_SUCCESS;
+	return ret;
+hbci_write_fail:
+	dev_err(&sr1xx_dev->spi->dev, "%s failed...%d", __func__, ret);
+	return ret;
+}
+
+static ssize_t sr1xx_dev_write(struct file *filp, const char *buf, size_t count,
+			       loff_t *offset)
+{
+	int ret;
+	struct sr1xx_dev *sr1xx_dev;
+
+	sr1xx_dev = filp->private_data;
+	if (count > SR1XX_MAX_TX_BUF_SIZE || count > SR1XX_TXBUF_SIZE) {
+		dev_err(&sr1xx_dev->spi->dev, "%s : Write Size Exceeds\n",
+			__func__);
+		ret = -ENOBUFS;
+		goto write_end;
+	}
+	if (copy_from_user(sr1xx_dev->tx_buffer, buf, count)) {
+		dev_err(&sr1xx_dev->spi->dev,
+			"%s : failed to copy from user space\n", __func__);
+		return -EFAULT;
+	}
+	if (sr1xx_dev->is_fw_dwnld_enabled)
+		ret = sr1xx_hbci_write(sr1xx_dev, count);
+	else
+		ret = sr1xx_dev_transceive(sr1xx_dev, SR1XX_WRITE_MODE, count);
+	if (ret == TRANSCEIVE_SUCCESS)
+		ret = sr1xx_dev->write_count;
+	else
+		dev_err(&sr1xx_dev->spi->dev, "write failed......");
+write_end:
+	return ret;
+}
+
+/**
+ * sr1xx_hbci_read
+ *
+ * Function used to read data from sr1xx on SPI line
+ * as part of firmware download sequence.
+ *
+ * Returns: Number of bytes read if read is success else (-1)
+ *               otherwise indicate each error code
+ */
+static ssize_t sr1xx_hbci_read(struct sr1xx_dev *sr1xx_dev, char *buf,
+			       size_t count)
+{
+	int ret = -EIO;
+
+	if (count > SR1XX_RXBUF_SIZE) {
+		dev_err(&sr1xx_dev->spi->dev, "count(%zu) out of range(0-%d)\n",
+			count, SR1XX_RXBUF_SIZE);
+		ret = -EINVAL;
+		goto hbci_fail;
+	}
+	/* Wait for inetrrupt upto 500ms */
+	ret = wait_event_interruptible_timeout(sr1xx_dev->read_wq,
+					       sr1xx_dev->irq_received,
+					       sr1xx_dev->timeout_in_ms);
+	if (ret == 0) {
+		dev_err(&sr1xx_dev->spi->dev,
+			"hbci wait_event_interruptible timeout() : Failed.\n");
+		ret = -1;
+		goto hbci_fail;
+	}
+	if (sr1xx_dev->read_abort_requested) {
+		sr1xx_dev->read_abort_requested = false;
+		dev_err(&sr1xx_dev->spi->dev, "HBCI Abort Read pending......");
+		return ret;
+	}
+	if (!gpio_get_value(sr1xx_dev->irq_gpio)) {
+		dev_err(&sr1xx_dev->spi->dev,
+			"IRQ is low during firmware download");
+		goto hbci_fail;
+	}
+	ret = spi_read(sr1xx_dev->spi, (void *)sr1xx_dev->rx_buffer, count);
+	if (ret < 0) {
+		dev_err(&sr1xx_dev->spi->dev,
+			"sr1xx_dev_read: spi read error %d\n ", ret);
+		goto hbci_fail;
+	}
+	ret = count;
+	if (copy_to_user(buf, sr1xx_dev->rx_buffer, count)) {
+		dev_err(&sr1xx_dev->spi->dev,
+			"sr1xx_dev_read: copy to user failed\n");
+		ret = -EFAULT;
+	}
+	return ret;
+hbci_fail:
+	dev_err(&sr1xx_dev->spi->dev, "Error sr1xx_fw_download ret %d Exit\n",
+		ret);
+	return ret;
+}
+
+static ssize_t sr1xx_dev_read(struct file *filp, char *buf, size_t count,
+			      loff_t *offset)
+{
+	struct sr1xx_dev *sr1xx_dev = filp->private_data;
+	int ret = -EIO;
+
+	/* 500ms timeout in jiffies */
+	sr1xx_dev->timeout_in_ms = ((500 * HZ) / 1000);
+	memset(sr1xx_dev->rx_buffer, 0x00, SR1XX_RXBUF_SIZE);
+	if (!gpio_get_value(sr1xx_dev->irq_gpio)) {
+		if (filp->f_flags & O_NONBLOCK) {
+			ret = -EAGAIN;
+			goto read_end;
+		}
+	}
+	/* HBCI packet read */
+	if (sr1xx_dev->is_fw_dwnld_enabled)
+		return sr1xx_hbci_read(sr1xx_dev, buf, count);
+	/* UCI packet read */
+first_irq_wait:
+	sr1xx_enable_irq(sr1xx_dev);
+	if (!sr1xx_dev->read_abort_requested) {
+		ret = wait_event_interruptible(sr1xx_dev->read_wq,
+					       sr1xx_dev->irq_received);
+		if (ret) {
+			dev_err(&sr1xx_dev->spi->dev,
+				"wait_event_interruptible() : Failed.\n");
+			goto read_end;
+		}
+	}
+	if (sr1xx_dev->read_abort_requested) {
+		sr1xx_dev->read_abort_requested = false;
+		dev_err(&sr1xx_dev->spi->dev, "Abort Read pending......");
+		return ret;
+	}
+	ret = sr1xx_dev_transceive(sr1xx_dev, SR1XX_READ_MODE, count);
+	if (ret == TRANSCEIVE_SUCCESS) {
+		if (copy_to_user(buf, sr1xx_dev->rx_buffer,
+				 sr1xx_dev->read_count)) {
+			dev_err(&sr1xx_dev->spi->dev,
+				"%s: copy to user failed\n", __func__);
+			ret = -EFAULT;
+			goto read_end;
+		}
+		ret = sr1xx_dev->read_count;
+	} else if (ret == IRQ_WAIT_REQUEST) {
+		dev_err(&sr1xx_dev->spi->dev,
+			"Irg is low due to write hence irq is requested again...");
+		goto first_irq_wait;
+	} else if (ret == IRQ_WAIT_TIMEOUT) {
+		dev_err(&sr1xx_dev->spi->dev,
+			"Second irq is not received..Time out...");
+		ret = -1;
+	} else {
+		dev_err(&sr1xx_dev->spi->dev, "spi read failed...%d", ret);
+		ret = -1;
+	}
+read_end:
+	return ret;
+}
+
+static int sr1xx_hw_setup(struct device *dev,
+			  struct sr1xx_spi_platform_data *platform_data)
+{
+	int ret;
+
+	ret = gpio_request(platform_data->irq_gpio, "sr1xx irq");
+	if (ret < 0) {
+		dev_err(dev, "gpio request failed gpio = 0x%x\n",
+			platform_data->irq_gpio);
+		goto fail;
+	}
+
+	ret = gpio_direction_input(platform_data->irq_gpio);
+	if (ret < 0) {
+		dev_err(dev, "gpio request failed gpio = 0x%x\n",
+			platform_data->irq_gpio);
+		goto fail_irq;
+	}
+
+	ret = gpio_request(platform_data->ce_gpio, "sr1xx ce");
+	if (ret < 0) {
+		dev_err(dev, "gpio request failed gpio = 0x%x\n",
+			platform_data->ce_gpio);
+		goto fail_gpio;
+	}
+
+	ret = gpio_direction_output(platform_data->ce_gpio, 0);
+	if (ret < 0) {
+		dev_err(dev, "sr1xx - Failed setting ce gpio - %d\n",
+			platform_data->ce_gpio);
+		goto fail_ce_gpio;
+	}
+
+	ret = gpio_request(platform_data->spi_handshake_gpio, "sr1xx ri");
+	if (ret < 0) {
+		dev_err(dev, "sr1xx - Failed requesting ri gpio - %d\n",
+			platform_data->spi_handshake_gpio);
+		goto fail_gpio;
+	}
+
+	ret = gpio_direction_output(platform_data->spi_handshake_gpio, 0);
+	if (ret < 0) {
+		dev_err(dev,
+			"sr1xx - Failed setting spi handeshake gpio - %d\n",
+			platform_data->spi_handshake_gpio);
+		goto fail_handshake_gpio;
+	}
+
+	ret = 0;
+	return ret;
+
+fail_gpio:
+fail_handshake_gpio:
+	gpio_free(platform_data->spi_handshake_gpio);
+fail_ce_gpio:
+	gpio_free(platform_data->ce_gpio);
+fail_irq:
+	gpio_free(platform_data->irq_gpio);
+fail:
+	dev_err(dev, "%s failed\n", __func__);
+	return ret;
+}
+
+static inline void sr1xx_set_data(struct spi_device *spi, void *data)
+{
+	dev_set_drvdata(&spi->dev, data);
+}
+
+static inline void *sr1xx_get_data(const struct spi_device *spi)
+{
+	return dev_get_drvdata(&spi->dev);
+}
+
+/* Possible fops on the sr1xx device */
+static const struct file_operations sr1xx_dev_fops = {
+	.owner = THIS_MODULE,
+	.read = sr1xx_dev_read,
+	.write = sr1xx_dev_write,
+	.open = sr1xx_dev_open,
+	.unlocked_ioctl = sr1xx_dev_ioctl,
+};
+
+static int sr1xx_parse_dt(struct device *dev,
+			  struct sr1xx_spi_platform_data *pdata)
+{
+	struct device_node *np = dev->of_node;
+
+	pdata->irq_gpio = of_get_named_gpio(np, "nxp,sr1xx-irq", 0);
+	if (!gpio_is_valid(pdata->irq_gpio))
+		return -EINVAL;
+	pdata->ce_gpio = of_get_named_gpio(np, "nxp,sr1xx-ce", 0);
+	if (!gpio_is_valid(pdata->ce_gpio))
+		return -EINVAL;
+	pdata->spi_handshake_gpio = of_get_named_gpio(np, "nxp,sr1xx-ri", 0);
+	if (!gpio_is_valid(pdata->spi_handshake_gpio))
+		return -EINVAL;
+	dev_info(
+		dev,
+		"sr1xx : irq_gpio = %d, ce_gpio = %d, spi_handshake_gpio = %d\n",
+		pdata->irq_gpio, pdata->ce_gpio, pdata->spi_handshake_gpio);
+	return 0;
+}
+
+/**
+ * sr1xx_gpio_cleanup
+ *
+ * Release requested gpios
+ *
+ */
+static void sr1xx_gpio_cleanup(struct sr1xx_spi_platform_data *pdata)
+{
+	if (gpio_is_valid(pdata->spi_handshake_gpio))
+		gpio_free(pdata->spi_handshake_gpio);
+	if (gpio_is_valid(pdata->ce_gpio))
+		gpio_free(pdata->ce_gpio);
+	if (gpio_is_valid(pdata->irq_gpio))
+		gpio_free(pdata->irq_gpio);
+}
+
+static int sr1xx_probe(struct spi_device *spi)
+{
+	int ret;
+	struct sr1xx_spi_platform_data *platform_data = NULL;
+	struct sr1xx_spi_platform_data platform_data1;
+	struct sr1xx_dev *sr1xx_dev = NULL;
+	unsigned int irq_flags;
+
+	dev_info(&spi->dev, "%s chip select : %d , bus number = %d\n", __func__,
+		 spi->chip_select, spi->master->bus_num);
+
+	ret = sr1xx_parse_dt(&spi->dev, &platform_data1);
+	if (ret) {
+		dev_err(&spi->dev, "%s - Failed to parse DT\n", __func__);
+		goto err_exit;
+	}
+	platform_data = &platform_data1;
+
+	sr1xx_dev = kzalloc(sizeof(*sr1xx_dev), GFP_KERNEL);
+	if (sr1xx_dev == NULL) {
+		ret = -ENOMEM;
+		goto err_exit;
+	}
+	ret = sr1xx_hw_setup(&spi->dev, platform_data);
+	if (ret < 0) {
+		dev_err(&spi->dev, "Failed to sr1xx_enable_SR1XX_IRQ_ENABLE\n");
+		goto err_setup;
+	}
+
+	spi->bits_per_word = 8;
+	spi->mode = SPI_MODE_0;
+	spi->max_speed_hz = SR1XX_SPI_CLOCK;
+	ret = spi_setup(spi);
+	if (ret < 0) {
+		dev_err(&spi->dev, "failed to do spi_setup()\n");
+		goto err_setup;
+	}
+
+	sr1xx_dev->spi = spi;
+	sr1xx_dev->sr1xx_device.minor = MISC_DYNAMIC_MINOR;
+	sr1xx_dev->sr1xx_device.name = "sr1xx";
+	sr1xx_dev->sr1xx_device.fops = &sr1xx_dev_fops;
+	sr1xx_dev->sr1xx_device.parent = &spi->dev;
+	sr1xx_dev->irq_gpio = platform_data->irq_gpio;
+	sr1xx_dev->ce_gpio = platform_data->ce_gpio;
+	sr1xx_dev->spi_handshake_gpio = platform_data->spi_handshake_gpio;
+
+	dev_set_drvdata(&spi->dev, sr1xx_dev);
+
+	/* init mutex and queues */
+	init_waitqueue_head(&sr1xx_dev->read_wq);
+	mutex_init(&sr1xx_dev->sr1xx_access_lock);
+
+	spin_lock_init(&sr1xx_dev->irq_enabled_lock);
+
+	ret = misc_register(&sr1xx_dev->sr1xx_device);
+	if (ret < 0) {
+		dev_err(&spi->dev, "misc_register failed! %d\n", ret);
+		goto err_setup;
+	}
+
+	sr1xx_dev->tx_buffer = kzalloc(SR1XX_TXBUF_SIZE, GFP_KERNEL);
+	sr1xx_dev->rx_buffer = kzalloc(SR1XX_RXBUF_SIZE, GFP_KERNEL);
+	if (sr1xx_dev->tx_buffer == NULL) {
+		ret = -ENOMEM;
+		goto exit_free_dev;
+	}
+	if (sr1xx_dev->rx_buffer == NULL) {
+		ret = -ENOMEM;
+		goto exit_free_dev;
+	}
+
+	sr1xx_dev->spi->irq = gpio_to_irq(platform_data->irq_gpio);
+
+	if (sr1xx_dev->spi->irq < 0) {
+		dev_err(&spi->dev, "gpio_to_irq request failed gpio = 0x%x\n",
+			platform_data->irq_gpio);
+		goto err_irq_request;
+	}
+	/* request irq. The irq is set whenever the chip has data available
+	 * for reading. It is cleared when all data has been read.
+	 */
+	irq_flags = IRQ_TYPE_LEVEL_HIGH;
+	sr1xx_dev->irq_enabled = true;
+	sr1xx_dev->irq_received = false;
+
+	ret = request_irq(sr1xx_dev->spi->irq, sr1xx_dev_irq_handler, irq_flags,
+			  sr1xx_dev->sr1xx_device.name, sr1xx_dev);
+	if (ret) {
+		dev_err(&spi->dev, "request_irq failed\n");
+		goto err_irq_request;
+	}
+	sr1xx_disable_irq(sr1xx_dev);
+	return ret;
+err_irq_request:
+exit_free_dev:
+	if (sr1xx_dev != NULL) {
+		kfree(sr1xx_dev->tx_buffer);
+		kfree(sr1xx_dev->rx_buffer);
+		misc_deregister(&sr1xx_dev->sr1xx_device);
+	}
+err_setup:
+	if (sr1xx_dev != NULL)
+		mutex_destroy(&sr1xx_dev->sr1xx_access_lock);
+err_exit:
+	sr1xx_gpio_cleanup(platform_data);
+	kfree(sr1xx_dev);
+	dev_err(&spi->dev, "ERROR: Exit : %s ret %d\n", __func__, ret);
+	return ret;
+}
+
+static void sr1xx_remove(struct spi_device *spi)
+{
+	struct sr1xx_dev *sr1xx_dev = sr1xx_get_data(spi);
+
+	gpio_free(sr1xx_dev->ce_gpio);
+	mutex_destroy(&sr1xx_dev->sr1xx_access_lock);
+	free_irq(sr1xx_dev->spi->irq, sr1xx_dev);
+	gpio_free(sr1xx_dev->irq_gpio);
+	gpio_free(sr1xx_dev->spi_handshake_gpio);
+	misc_deregister(&sr1xx_dev->sr1xx_device);
+	if (sr1xx_dev != NULL) {
+		kfree(sr1xx_dev->tx_buffer);
+		kfree(sr1xx_dev->rx_buffer);
+		kfree(sr1xx_dev);
+	}
+}
+
+/**
+ * sr1xx_dev_suspend
+ *
+ * Executed before putting the system into a sleep state
+ *
+ */
+int sr1xx_dev_suspend(struct device *dev)
+{
+	struct sr1xx_dev *sr1xx_dev = dev_get_drvdata(dev);
+
+	if (device_may_wakeup(dev))
+		disable_irq_wake(sr1xx_dev->spi->irq);
+	return 0;
+}
+
+/**
+ * sr1xx_dev_resume
+ *
+ * Executed after waking the system up from a sleep state
+ *
+ */
+
+int sr1xx_dev_resume(struct device *dev)
+{
+	struct sr1xx_dev *sr1xx_dev = dev_get_drvdata(dev);
+
+	if (device_may_wakeup(dev))
+		enable_irq_wake(sr1xx_dev->spi->irq);
+
+	return 0;
+}
+
+static const struct of_device_id sr1xx_dt_match[] = {
+	{
+		.compatible = "nxp,sr1xx",
+	},
+	{}
+};
+
+static const struct dev_pm_ops sr1xx_dev_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(
+	sr1xx_dev_suspend, sr1xx_dev_resume) };
+
+static struct spi_driver sr1xx_driver = {
+	.driver = {
+		   .name = "sr1xx",
+		   .pm = &sr1xx_dev_pm_ops,
+		   .bus = &spi_bus_type,
+		   .owner = THIS_MODULE,
+		   .of_match_table = sr1xx_dt_match,
+		    },
+	.probe = sr1xx_probe,
+	.remove = sr1xx_remove,
+};
+
+static int __init sr1xx_dev_init(void)
+{
+	return spi_register_driver(&sr1xx_driver);
+}
+
+module_init(sr1xx_dev_init);
+
+static void __exit sr1xx_dev_exit(void)
+{
+	spi_unregister_driver(&sr1xx_driver);
+}
+
+module_exit(sr1xx_dev_exit);
+
+MODULE_AUTHOR("Manjunatha Venkatesh <manjunatha.venkatesh@nxp.com>");
+MODULE_DESCRIPTION("NXP SR1XX SPI driver");
+MODULE_LICENSE("GPL");