diff mbox series

[v9,05/10] dt-bindings: sc16is7xx: Add property to change GPIO function

Message ID 20230725142343.1724130-6-hugo@hugovil.com
State Superseded
Headers show
Series None | expand

Commit Message

Hugo Villeneuve July 25, 2023, 2:23 p.m. UTC
From: Hugo Villeneuve <hvilleneuve@dimonoff.com>

Some variants in this series of UART controllers have GPIO pins that
are shared between GPIO and modem control lines.

The pin mux mode (GPIO or modem control lines) can be set for each
ports (channels) supported by the variant.

This adds a property to the device tree to set the GPIO pin mux to
modem control lines on selected ports if needed.

Cc: <stable@vger.kernel.org> # 6.1.x
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
---
 .../bindings/serial/nxp,sc16is7xx.txt         | 46 +++++++++++++++++++
 1 file changed, 46 insertions(+)
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
index 0fa8e3e43bf8..1a7e4bff0456 100644
--- a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
+++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.txt
@@ -23,6 +23,9 @@  Optional properties:
     1 = active low.
 - irda-mode-ports: An array that lists the indices of the port that
 		   should operate in IrDA mode.
+- nxp,modem-control-line-ports: An array that lists the indices of the port that
+				should have shared GPIO lines configured as
+				modem control lines.
 
 Example:
         sc16is750: sc16is750@51 {
@@ -35,6 +38,26 @@  Example:
                 #gpio-cells = <2>;
         };
 
+	sc16is752: sc16is752@53 {
+		compatible = "nxp,sc16is752";
+		reg = <0x53>;
+		clocks = <&clk20m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */
+		gpio-controller; /* Port 0 as GPIOs */
+		#gpio-cells = <2>;
+	};
+
+	sc16is752: sc16is752@54 {
+		compatible = "nxp,sc16is752";
+		reg = <0x54>;
+		clocks = <&clk20m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */
+	};
+
 * spi as bus
 
 Required properties:
@@ -59,6 +82,9 @@  Optional properties:
     1 = active low.
 - irda-mode-ports: An array that lists the indices of the port that
 		   should operate in IrDA mode.
+- nxp,modem-control-line-ports: An array that lists the indices of the port that
+				should have shared GPIO lines configured as
+				modem control lines.
 
 Example:
 	sc16is750: sc16is750@0 {
@@ -70,3 +96,23 @@  Example:
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
+
+	sc16is752: sc16is752@1 {
+		compatible = "nxp,sc16is752";
+		reg = <1>;
+		clocks = <&clk20m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		nxp,modem-control-line-ports = <1>; /* Port 1 as modem control lines */
+		gpio-controller; /* Port 0 as GPIOs */
+		#gpio-cells = <2>;
+	};
+
+	sc16is752: sc16is752@2 {
+		compatible = "nxp,sc16is752";
+		reg = <2>;
+		clocks = <&clk20m>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		nxp,modem-control-line-ports = <0 1>; /* Ports 0 and 1 as modem control lines */
+	};