diff mbox series

[v4,1/2] dt-bindings: backlight: Add MPS MP3309C

Message ID 20231010121621.3009154-1-f.suligoi@asem.it
State New
Headers show
Series [v4,1/2] dt-bindings: backlight: Add MPS MP3309C | expand

Commit Message

Flavio Suligoi Oct. 10, 2023, 12:16 p.m. UTC
The Monolithic Power (MPS) MP3309C is a WLED step-up converter, featuring a
programmable switching frequency to optimize efficiency.
The brightness can be controlled either by I2C commands (called "analog"
mode) or by a PWM input signal (PWM mode).
This driver supports both modes.

For device driver details, please refer to:
- drivers/video/backlight/mp3309c_bl.c

The datasheet is available at:
- https://www.monolithicpower.com/en/mp3309c.html

Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
---

v4:
 - remove not more used allOf keyword
 - add brightness-levels and default-brightness properties
 - remove max-brightness and default-brightness from required properties
 - update example, adding brightness-levels and default-brightness properties
v3:
 - add default value for mps,overvoltage-protection-microvolt property
 - fix the example, changing from "mps,mp3309c-backlight" to "mps,mp3309c" in
   compatible property
v2:
 - remove useless properties (dimming-mode, pinctrl-names, pinctrl-0,
   switch-on-delay-ms, switch-off-delay-ms, reset-gpios, reset-on-delay-ms,
   reset-on-length-ms)
 - add common.yaml#
 - remove already included properties (default-brightness, max-brightness)
 - substitute three boolean properties, used for the overvoltage-protection
   values, with a single enum property
 - remove some conditional definitions
 - remove the 2nd example
v1:
 - first version

 .../bindings/leds/backlight/mps,mp3309c.yaml  | 82 +++++++++++++++++++
 1 file changed, 82 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml

Comments

Rob Herring (Arm) Oct. 10, 2023, 4:15 p.m. UTC | #1
On Tue, Oct 10, 2023 at 02:16:21PM +0200, Flavio Suligoi wrote:
> The Monolithic Power (MPS) MP3309C is a WLED step-up converter, featuring a
> programmable switching frequency to optimize efficiency.
> The brightness can be controlled either by I2C commands (called "analog"
> mode) or by a PWM input signal (PWM mode).
> This driver supports both modes.
> 
> For device driver details, please refer to:
> - drivers/video/backlight/mp3309c_bl.c
> 
> The datasheet is available at:
> - https://www.monolithicpower.com/en/mp3309c.html
> 
> Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
> ---
> 
> v4:
>  - remove not more used allOf keyword
>  - add brightness-levels and default-brightness properties
>  - remove max-brightness and default-brightness from required properties
>  - update example, adding brightness-levels and default-brightness properties
> v3:
>  - add default value for mps,overvoltage-protection-microvolt property
>  - fix the example, changing from "mps,mp3309c-backlight" to "mps,mp3309c" in
>    compatible property
> v2:
>  - remove useless properties (dimming-mode, pinctrl-names, pinctrl-0,
>    switch-on-delay-ms, switch-off-delay-ms, reset-gpios, reset-on-delay-ms,
>    reset-on-length-ms)
>  - add common.yaml#
>  - remove already included properties (default-brightness, max-brightness)
>  - substitute three boolean properties, used for the overvoltage-protection
>    values, with a single enum property
>  - remove some conditional definitions
>  - remove the 2nd example
> v1:
>  - first version
> 
>  .../bindings/leds/backlight/mps,mp3309c.yaml  | 82 +++++++++++++++++++
>  1 file changed, 82 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
> 
> diff --git a/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml b/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
> new file mode 100644
> index 000000000000..e2f9ae2b3fb4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
> @@ -0,0 +1,82 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/leds/backlight/mps,mp3309c.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: MPS MP3309C backlight
> +
> +maintainers:
> +  - Flavio Suligoi <f.suligoi@asem.it>
> +
> +description: |
> +  The Monolithic Power (MPS) MP3309C is a WLED step-up converter, featuring a
> +  programmable switching frequency to optimize efficiency.
> +  It supports two different dimming modes:
> +
> +  - analog mode, via I2C commands, as default mode (32 dimming levels)
> +  - PWM controlled mode (optional)
> +
> +  The datasheet is available at:
> +  https://www.monolithicpower.com/en/mp3309c.html
> +
> +properties:
> +  compatible:
> +    const: mps,mp3309c
> +
> +  reg:
> +    maxItems: 1
> +
> +  pwms:
> +    description: if present, the backlight is controlled in PWM mode.
> +    maxItems: 1
> +
> +  enable-gpios:
> +    description: GPIO used to enable the backlight in "analog-i2c" dimming mode.
> +    maxItems: 1
> +
> +  brightness-levels:
> +    description:
> +      Array of distinct brightness levels, in PWM dimming mode.
> +      Typically these are in the range from 0 to 255, but any range starting
> +      at 0 will do.
> +      The 0 value means a 0% duty cycle (darkest/off), while the last value in
> +      the array represents a 100% duty cycle (brightest).
> +    $ref: /schemas/types.yaml#/definitions/uint32-array

This already has a type defined. Please add it to backlight/common.yaml 
and remove from led-backlight.yaml and pwm-backlight.yaml.

You say 0-255 here, but your example is 0-10. One of those seems wrong. 
Anyways, don't define constraints in prose, use a schema:

items:
  maximum: 10 (or 255?)

> +
> +  default-brightness:
> +    description:
> +      The default brightness (index into the levels array).
> +    $ref: /schemas/types.yaml#/definitions/uint32

Already has a type. You need to reference backlight/common.yaml.

> +
> +  mps,overvoltage-protection-microvolt:
> +    description: Overvoltage protection (13.5V, 24V or 35.5V).
> +    enum: [ 13500000, 24000000, 35500000 ]
> +    default: 35500000
> +
> +  mps,no-sync-mode:
> +    description: disable synchronous rectification mode
> +    type: boolean
> +
> +required:
> +  - compatible
> +  - reg
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    i2c {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        /* Backlight with PWM control */
> +        backlight_pwm: backlight@17 {
> +            compatible = "mps,mp3309c";
> +            reg = <0x17>;
> +            pwms = <&pwm1 0 3333333 0>; /* 300 Hz --> (1/f) * 1*10^9 */
> +            brightness-levels = <0 1 2 3 4 5 6 7 8 9 10>;
> +            default-brightness = <8>;
> +            mps,overvoltage-protection-microvolt = <24000000>;
> +        };
> +    };
> -- 
> 2.34.1
>
Flavio Suligoi Oct. 11, 2023, 11:52 a.m. UTC | #2
Hi Rob,

... 
> >  .../bindings/leds/backlight/mps,mp3309c.yaml  | 82
> > +++++++++++++++++++
> >  1 file changed, 82 insertions(+)
> >  create mode 100644
> > Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
> >
> > diff --git
> > a/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
> > b/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
> > new file mode 100644
> > index 000000000000..e2f9ae2b3fb4
> > --- /dev/null
> > +++
> b/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yam
> > +++ l
> > @@ -0,0 +1,82 @@
> > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/leds/backlight/mps,mp3309c.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: MPS MP3309C backlight
> > +
> > +maintainers:
> > +  - Flavio Suligoi <f.suligoi@asem.it>
> > +
> > +description: |
> > +  The Monolithic Power (MPS) MP3309C is a WLED step-up converter,
> > +featuring a
> > +  programmable switching frequency to optimize efficiency.
> > +  It supports two different dimming modes:
> > +
> > +  - analog mode, via I2C commands, as default mode (32 dimming
> > + levels)
> > +  - PWM controlled mode (optional)
> > +
> > +  The datasheet is available at:
> > +  https://www.monolithicpower.com/en/mp3309c.html
> > +
> > +properties:
> > +  compatible:
> > +    const: mps,mp3309c
> > +
> > +  reg:
> > +    maxItems: 1
> > +
> > +  pwms:
> > +    description: if present, the backlight is controlled in PWM mode.
> > +    maxItems: 1
> > +
> > +  enable-gpios:
> > +    description: GPIO used to enable the backlight in "analog-i2c" dimming
> mode.
> > +    maxItems: 1
> > +
> > +  brightness-levels:
> > +    description:
> > +      Array of distinct brightness levels, in PWM dimming mode.
> > +      Typically these are in the range from 0 to 255, but any range starting
> > +      at 0 will do.
> > +      The 0 value means a 0% duty cycle (darkest/off), while the last value in
> > +      the array represents a 100% duty cycle (brightest).
> > +    $ref: /schemas/types.yaml#/definitions/uint32-array
> 
> This already has a type defined. Please add it to backlight/common.yaml and
> remove from led-backlight.yaml and pwm-backlight.yaml.

Ok, I'll add common.yaml and I'll prepare two other separate patches for these.

> 
> You say 0-255 here, but your example is 0-10. One of those seems wrong.
> Anyways, don't define constraints in prose, use a schema:
> 
> items:
>   maximum: 10 (or 255?)

Ok, I'll add maximum, and I'll change the example, using 0..255

> 
> > +
> > +  default-brightness:
> > +    description:
> > +      The default brightness (index into the levels array).
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> 
> Already has a type. You need to reference backlight/common.yaml.

Ok

> 
> > +
> > +  mps,overvoltage-protection-microvolt:
> > +    description: Overvoltage protection (13.5V, 24V or 35.5V).
> > +    enum: [ 13500000, 24000000, 35500000 ]
> > +    default: 35500000
> > +
> > +  mps,no-sync-mode:
> > +    description: disable synchronous rectification mode
> > +    type: boolean
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +
> > +unevaluatedProperties: false
> > +
> > +examples:
> > +  - |
> > +    i2c {
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +        /* Backlight with PWM control */
> > +        backlight_pwm: backlight@17 {
> > +            compatible = "mps,mp3309c";
> > +            reg = <0x17>;
> > +            pwms = <&pwm1 0 3333333 0>; /* 300 Hz --> (1/f) * 1*10^9 */
> > +            brightness-levels = <0 1 2 3 4 5 6 7 8 9 10>;
> > +            default-brightness = <8>;
> > +            mps,overvoltage-protection-microvolt = <24000000>;
> > +        };
> > +    };
> > --
> > 2.34.1
> >

Thanks,
Flavio
Flavio Suligoi Oct. 11, 2023, 3:13 p.m. UTC | #3
Hi Rob,

just a question about led-backlight.yaml and pwm-backlight.yaml
common properties.

...

> > +
> > +  brightness-levels:
> > +    description:
> > +      Array of distinct brightness levels, in PWM dimming mode.
> > +      Typically these are in the range from 0 to 255, but any range starting
> > +      at 0 will do.
> > +      The 0 value means a 0% duty cycle (darkest/off), while the last value in
> > +      the array represents a 100% duty cycle (brightest).
> > +    $ref: /schemas/types.yaml#/definitions/uint32-array
> 
> This already has a type defined. Please add it to backlight/common.yaml and
> remove from led-backlight.yaml and pwm-backlight.yaml.

As well as the brightness-levels property, also the default-brightness-level is in common
between led-backlight.yaml and pwm-backlight.yaml.
What do you think about removing it from both led-backlight.yaml and pwm-backlight.yaml, and
moving it into backlight/common.yaml?

> 
> You say 0-255 here, but your example is 0-10. One of those seems wrong.
> Anyways, don't define constraints in prose, use a schema:
> 
> items:
>   maximum: 10 (or 255?)
> 
> > +
> > +  default-brightness:
> > +    description:
> > +      The default brightness (index into the levels array).
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> 
> Already has a type. You need to reference backlight/common.yaml.
> 
> > +
> > +  mps,overvoltage-protection-microvolt:
> > +    description: Overvoltage protection (13.5V, 24V or 35.5V).
> > +    enum: [ 13500000, 24000000, 35500000 ]
> > +    default: 35500000
> > +
> > +  mps,no-sync-mode:
> > +    description: disable synchronous rectification mode
> > +    type: boolean
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +
> > +unevaluatedProperties: false
> > +
> > +examples:
> > +  - |
> > +    i2c {
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +        /* Backlight with PWM control */
> > +        backlight_pwm: backlight@17 {
> > +            compatible = "mps,mp3309c";
> > +            reg = <0x17>;
> > +            pwms = <&pwm1 0 3333333 0>; /* 300 Hz --> (1/f) * 1*10^9 */
> > +            brightness-levels = <0 1 2 3 4 5 6 7 8 9 10>;
> > +            default-brightness = <8>;
> > +            mps,overvoltage-protection-microvolt = <24000000>;
> > +        };
> > +    };
> > --
> > 2.34.1
> >

Regards,
Flavio
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml b/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
new file mode 100644
index 000000000000..e2f9ae2b3fb4
--- /dev/null
+++ b/Documentation/devicetree/bindings/leds/backlight/mps,mp3309c.yaml
@@ -0,0 +1,82 @@ 
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/leds/backlight/mps,mp3309c.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MPS MP3309C backlight
+
+maintainers:
+  - Flavio Suligoi <f.suligoi@asem.it>
+
+description: |
+  The Monolithic Power (MPS) MP3309C is a WLED step-up converter, featuring a
+  programmable switching frequency to optimize efficiency.
+  It supports two different dimming modes:
+
+  - analog mode, via I2C commands, as default mode (32 dimming levels)
+  - PWM controlled mode (optional)
+
+  The datasheet is available at:
+  https://www.monolithicpower.com/en/mp3309c.html
+
+properties:
+  compatible:
+    const: mps,mp3309c
+
+  reg:
+    maxItems: 1
+
+  pwms:
+    description: if present, the backlight is controlled in PWM mode.
+    maxItems: 1
+
+  enable-gpios:
+    description: GPIO used to enable the backlight in "analog-i2c" dimming mode.
+    maxItems: 1
+
+  brightness-levels:
+    description:
+      Array of distinct brightness levels, in PWM dimming mode.
+      Typically these are in the range from 0 to 255, but any range starting
+      at 0 will do.
+      The 0 value means a 0% duty cycle (darkest/off), while the last value in
+      the array represents a 100% duty cycle (brightest).
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+
+  default-brightness:
+    description:
+      The default brightness (index into the levels array).
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  mps,overvoltage-protection-microvolt:
+    description: Overvoltage protection (13.5V, 24V or 35.5V).
+    enum: [ 13500000, 24000000, 35500000 ]
+    default: 35500000
+
+  mps,no-sync-mode:
+    description: disable synchronous rectification mode
+    type: boolean
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        /* Backlight with PWM control */
+        backlight_pwm: backlight@17 {
+            compatible = "mps,mp3309c";
+            reg = <0x17>;
+            pwms = <&pwm1 0 3333333 0>; /* 300 Hz --> (1/f) * 1*10^9 */
+            brightness-levels = <0 1 2 3 4 5 6 7 8 9 10>;
+            default-brightness = <8>;
+            mps,overvoltage-protection-microvolt = <24000000>;
+        };
+    };