diff mbox series

[v5,03/10] media: i2c: imx290: fix reset GPIO pin handling

Message ID 20200612135355.30286-4-andrey.konovalov@linaro.org
State Accepted
Commit 3909a92d7df622b41b9ceeeea694e641cad7667b
Headers show
Series Improvements to IMX290 CMOS driver | expand

Commit Message

Andrey Konovalov June 12, 2020, 1:53 p.m. UTC 
According to https://www.kernel.org/doc/Documentation/gpio/consumer.txt,

- all of the gpiod_set_value_xxx() functions operate with the *logical*
value. So in imx290_power_on() the reset signal should be cleared
(de-asserted) with gpiod_set_value_cansleep(imx290->rst_gpio, 0), and in
imx290_power_off() the value of 1 must be used to apply/assert the reset
to the sensor. In the device tree the reset pin is described as
GPIO_ACTIVE_LOW, and gpiod_set_value_xxx() functions take this into
account,

- when devm_gpiod_get_optional() is called with GPIOD_ASIS, the GPIO is
not initialized, and the direction must be set later; using a GPIO
without setting its direction first is illegal and will result in undefined
behavior. Fix this by using GPIOD_OUT_HIGH instead of GPIOD_ASIS (this
asserts the reset signal to the sensor initially).

Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

---
 drivers/media/i2c/imx290.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

-- 
2.17.1
diff mbox series

Patch

diff --git a/drivers/media/i2c/imx290.c b/drivers/media/i2c/imx290.c
index d0322f9a8856..7b1de1f0c8b7 100644
--- a/drivers/media/i2c/imx290.c
+++ b/drivers/media/i2c/imx290.c
@@ -628,7 +628,7 @@  static int imx290_power_on(struct device *dev)
 	}
 
 	usleep_range(1, 2);
-	gpiod_set_value_cansleep(imx290->rst_gpio, 1);
+	gpiod_set_value_cansleep(imx290->rst_gpio, 0);
 	usleep_range(30000, 31000);
 
 	return 0;
@@ -641,7 +641,7 @@  static int imx290_power_off(struct device *dev)
 	struct imx290 *imx290 = to_imx290(sd);
 
 	clk_disable_unprepare(imx290->xclk);
-	gpiod_set_value_cansleep(imx290->rst_gpio, 0);
+	gpiod_set_value_cansleep(imx290->rst_gpio, 1);
 	regulator_bulk_disable(IMX290_NUM_SUPPLIES, imx290->supplies);
 
 	return 0;
@@ -757,7 +757,8 @@  static int imx290_probe(struct i2c_client *client)
 		goto free_err;
 	}
 
-	imx290->rst_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_ASIS);
+	imx290->rst_gpio = devm_gpiod_get_optional(dev, "reset",
+						   GPIOD_OUT_HIGH);
 	if (IS_ERR(imx290->rst_gpio)) {
 		dev_err(dev, "Cannot get reset gpio\n");
 		ret = PTR_ERR(imx290->rst_gpio);