mbox series

[0/6] Initial Samsung Galaxy A8 (2018) support

Message ID 20211205153302.76418-1-virag.david003@gmail.com
Headers show
Series Initial Samsung Galaxy A8 (2018) support | expand

Message

David Virag Dec. 5, 2021, 3:32 p.m. UTC
Add basic initial support for the Samsung Galaxy A8 (2018) smartphone.
This phone is also known as "jackpotlte" and under the model name
"SM-A530F". In its current state this should work on most if not all
Exynos7885 phones/devices released.

As of now, it supports I2C nodes (all disabled by default) and UART
console with basic clock support in place.

To access the UART console on the A8, there are two methods:
  -You can open up the device and solder directly to some debug pins
   close to the display connector.
  -Through I2C you can set the S2MU004 MFD chip to multiplex the SoC's
   UART lines to the d+ and d- on the USB Type-C port of the device.

Note that UART works on 1.8 volts, so plugging in a normal USB cable
while multiplexed to UART may fry the SoC.

Everything was tested through UART by using a minimal driver that sets
the S2MU004 to multiplex UART.

The preferred way to boot this device is using my Minimal S-Boot Wrapper
[1] to work around some issues caused by the stock, and non-replacable
Samsung S-Boot bootloader.

[1] https://github.com/VDavid003/minimal_sboot_wrapper

David Virag (6):
  clk: samsung: clk-pll: Add support for pll1417x
  dt-bindings: clock: Add bindings definitions for Exynos7885 CMU
  dt-bindings: clock: Document Exynos7885 CMU bindings
  clk: samsung: Add initial Exynos7885 clock driver
  dt-bindings: arm: samsung: document jackpotlte board binding
  arm64: dts: exynos: Add initial device tree support for Exynos7885 SoC

 .../bindings/arm/samsung/samsung-boards.yaml  |   6 +
 .../clock/samsung,exynos7885-clock.yaml       | 166 ++++
 arch/arm64/boot/dts/exynos/Makefile           |   7 +-
 .../boot/dts/exynos/exynos7885-jackpotlte.dts |  95 ++
 .../boot/dts/exynos/exynos7885-pinctrl.dtsi   | 929 ++++++++++++++++++
 arch/arm64/boot/dts/exynos/exynos7885.dtsi    | 444 +++++++++
 drivers/clk/samsung/Makefile                  |   1 +
 drivers/clk/samsung/clk-exynos7885.c          | 680 +++++++++++++
 drivers/clk/samsung/clk-pll.c                 |   1 +
 drivers/clk/samsung/clk-pll.h                 |   1 +
 include/dt-bindings/clock/exynos7885.h        | 115 +++
 11 files changed, 2442 insertions(+), 3 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/samsung,exynos7885-clock.yaml
 create mode 100644 arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts
 create mode 100644 arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi
 create mode 100644 arch/arm64/boot/dts/exynos/exynos7885.dtsi
 create mode 100644 drivers/clk/samsung/clk-exynos7885.c
 create mode 100644 include/dt-bindings/clock/exynos7885.h

Comments

David Virag Dec. 7, 2021, 4:34 p.m. UTC | #1
Hi!

On Tue, 2021-12-07 at 09:26 +0100, Pavel Machek wrote:
> Hi!
> 
> > Add basic initial support for the Samsung Galaxy A8 (2018)
> > smartphone.
> > This phone is also known as "jackpotlte" and under the model name
> > "SM-A530F". In its current state this should work on most if not
> > all
> > Exynos7885 phones/devices released.
> 
> Thank you, it is good to see support for more hardware.
> 
> Can I get you to cc phone-devel@vger.kernel.org mailing list in
> future?

Sure, I did not know about this mailing list. I will CC it in the
future!

> 
> Besst regards,
>                                                                 Pavel
>                                                                 
> 

Best regards,
David