diff mbox series

[v2,3/8] pm80xx: check main config table address

Message ID 20210109123849.17098-4-Viswas.G@microchip.com
State New
Headers show
Series pm80xx updates. | expand

Commit Message

Viswas G Jan. 9, 2021, 12:38 p.m. UTC
From: akshatzen <akshatzen@google.com>

pm8001 driver initializes main configuration, general status, inbound
queue and outbound queue table address based on value read from
MSGU_SCRATCH_PAD_0 register.

We should validate these addresses before dereferencing them.

This change adds two validations:
1. Check if main configuration table offset lies within the pcibar
mapped
2. Check if first dword of main configuration table reads "PMCS"

There are two calls to init_pci_device_addresses() done during
pm8001_pci_probe() in this sequence:
1. First inside chip_soft_rst, where if init_pci_device_addresses fails
we will go ahead assuming MPI state is not ready and reset the device as
long as bootloader is okay.  This gives chance to second call of
init_pci_device_addresses to set up the addresses after reset.

2. The second call is via pm80xx_chip_init, after soft reset is done and
firmware is checked to be ready. Once that is done we are safe to go
ahead and initialize default table values and use them.

Tested:

1. Enabled debugging logs and observed no issues during initialization,
with a controller with No issues.

pm80xx0:: pm8001_setup_msix 1034: pci_alloc_irq_vectors request ret:64
no of intr 64
pm80xx0:: init_pci_device_addresses 917: Scratchpad 0 Offset: 0x2000
value 0x40002000
pm80xx0:: init_pci_device_addresses 925: Scratchpad 0 PCI BAR: 0
pm80xx0:: init_pci_device_addresses 952: VALID main config signature
0x53434d50
pm80xx0:: init_pci_device_addresses 975: GST OFFSET 0xc4
pm80xx0:: init_pci_device_addresses 978: INBND OFFSET 0x20000128
pm80xx0:: init_pci_device_addresses 981: OBND OFFSET 0x24000928
pm80xx0:: init_pci_device_addresses 984: IVT OFFSET 0x8001408
pm80xx0:: init_pci_device_addresses 987: PSPA OFFSET 0x8001608
pm80xx0:: init_pci_device_addresses 991: addr - main cfg (ptrval)
general status (ptrval)
pm80xx0:: init_pci_device_addresses 995: addr - inbnd (ptrval) obnd
(ptrval)
pm80xx0:: init_pci_device_addresses 999: addr - pspa (ptrval) ivt
(ptrval)
pm80xx0:: pm80xx_chip_soft_rst 1446: reset register before write : 0x0
pm80xx0:: pm80xx_chip_soft_rst 1478: reset register after write 0x40
pm80xx0:: pm80xx_chip_soft_rst 1544: SPCv soft reset Complete
pm80xx0:: init_pci_device_addresses 917: Scratchpad 0 Offset: 0x2000
value 0x40002000
pm80xx0:: init_pci_device_addresses 925: Scratchpad 0 PCI BAR: 0
pm80xx0:: init_pci_device_addresses 952: VALID main config signature
0x53434d50
pm80xx0:: init_pci_device_addresses 975: GST OFFSET 0xc4
pm80xx0:: init_pci_device_addresses 978: INBND OFFSET 0x20000128
pm80xx0:: init_pci_device_addresses 981: OBND OFFSET 0x24000928
pm80xx0:: init_pci_device_addresses 984: IVT OFFSET 0x8001408
pm80xx0:: init_pci_device_addresses 987: PSPA OFFSET 0x8001608
pm80xx0:: init_pci_device_addresses 991: addr - main cfg (ptrval)
general status (ptrval)
pm80xx0:: init_pci_device_addresses 995: addr - inbnd (ptrval) obnd
(ptrval)
pm80xx0:: init_pci_device_addresses 999: addr - pspa (ptrval) ivt
(ptrval)
pm80xx0:: pm80xx_chip_init 1329: MPI initialize successful!

2. Tested controller with firmware known to have initialization issue
and observed no crashes with this fix

pm80xx 0000:01:00.0: pm80xx: driver version 0.1.38
pm80xx 0000:01:00.0: Removing from 1:1 domain
pm80xx 0000:01:00.0: Requesting non-1:1 mappings
pm80xx0:: init_pci_device_addresses 948: BAD main config signature 0x0
pm80xx0:: mpi_uninit_check 1365: Failed to init pci addresses
pm80xx0:: pm80xx_chip_soft_rst 1435: MPI state is not ready
scratch:0:8:62a01000:0
pm80xx0:: pm80xx_chip_soft_rst 1518: Firmware is not ready!
pm80xx0:: pm80xx_chip_soft_rst 1532: iButton Feature is not Available!!!
pm80xx0:: pm80xx_chip_init 1301: Firmware is not ready!
pm80xx0:: pm8001_pci_probe 1215: chip_init failed [ret: -16]
pm80xx: probe of 0000:01:00.0 failed with error -16
pm80xx 0000:07:00.0: pm80xx: driver version 0.1.38
pm80xx 0000:07:00.0: Removing from 1:1 domain
pm80xx 0000:07:00.0: Requesting non-1:1 mappings
scsi host6: pm80xx
pm80xx1:: pm8001_setup_sgpio 5568: failed sgpio_req timeout
pm80xx1:: mpi_phy_start_resp 3447: phy start resp status:0x0, phyid:0x0
pm80xx 0000:08:00.0: pm80xx: driver version 0.1.38
pm80xx 0000:08:00.0: Removing from 1:1 domain
pm80xx 0000:08:00.0: Requesting non-1:1 mappings

3. Without this fix we observe crash on the same controller.

pm80xx 0000:01:00.0: pm80xx: driver version 0.1.38
pm80xx 0000:01:00.0: Removing from 1:1 domain
pm80xx 0000:01:00.0: Requesting non-1:1 mappings
[<ffffffffc0451b3b>] pm80xx_chip_soft_rst+0x6b/0x4c0 [pm80xx]
[<ffffffffc043a933>] pm8001_pci_probe+0xa43/0x1630 [pm80xx]
RIP: 0010:pm80xx_chip_soft_rst+0x71/0x4c0 [pm80xx]
[<ffffffffc0451b3b>] ? pm80xx_chip_soft_rst+0x6b/0x4c0 [pm80xx]
[<ffffffffc043a933>] pm8001_pci_probe+0xa43/0x1630 [pm80xx]
pm80xx0:: mpi_uninit_check 1339: TIMEOUT:IBDB value/=2
pm80xx0:: pm80xx_chip_soft_rst 1387: MPI state is not ready
scratch:0:8:62a01000:0
pm80xx0:: pm80xx_chip_soft_rst 1470: Firmware is not ready!
pm80xx0:: pm80xx_chip_soft_rst 1484: iButton Feature is not Available!!!
pm80xx0:: pm80xx_chip_init 1266: Firmware is not ready!
pm80xx0:: pm8001_pci_probe 1207: chip_init failed [ret: -16]
pm80xx: probe of 0000:01:00.0 failed with error -16

Signed-off-by: akshatzen <akshatzen@google.com>
Signed-off-by: Viswas G <Viswas.G@microchip.com>
Signed-off-by: Ruksar Devadi <Ruksar.devadi@microchip.com>
Signed-off-by: Radha Ramachandran <radha@google.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
---
 drivers/scsi/pm8001/pm8001_init.c | 11 +++++---
 drivers/scsi/pm8001/pm80xx_hwi.c  | 53 ++++++++++++++++++++++++++++++++++++---
 2 files changed, 58 insertions(+), 6 deletions(-)
diff mbox series

Patch

diff --git a/drivers/scsi/pm8001/pm8001_init.c b/drivers/scsi/pm8001/pm8001_init.c
index ee2de177d0d0..d21078ca7fb3 100644
--- a/drivers/scsi/pm8001/pm8001_init.c
+++ b/drivers/scsi/pm8001/pm8001_init.c
@@ -466,9 +466,12 @@  static int pm8001_ioremap(struct pm8001_hba_info *pm8001_ha)
 			pm8001_ha->io_mem[logicalBar].memvirtaddr =
 				ioremap(pm8001_ha->io_mem[logicalBar].membase,
 				pm8001_ha->io_mem[logicalBar].memsize);
-			pm8001_dbg(pm8001_ha, INIT,
-				   "PCI: bar %d, logicalBar %d\n",
+			if (!pm8001_ha->io_mem[logicalBar].memvirtaddr) {
+				pm8001_dbg(pm8001_ha, INIT,
+					"Failed to ioremap bar %d, logicalBar %d",
 				   bar, logicalBar);
+				return -ENOMEM;
+			}
 			pm8001_dbg(pm8001_ha, INIT,
 				   "base addr %llx virt_addr=%llx len=%d\n",
 				   (u64)pm8001_ha->io_mem[logicalBar].membase,
@@ -540,9 +543,11 @@  static struct pm8001_hba_info *pm8001_pci_alloc(struct pci_dev *pdev,
 			tasklet_init(&pm8001_ha->tasklet[j], pm8001_tasklet,
 				(unsigned long)&(pm8001_ha->irq_vector[j]));
 #endif
-	pm8001_ioremap(pm8001_ha);
+	if (pm8001_ioremap(pm8001_ha))
+		goto failed_pci_alloc;
 	if (!pm8001_alloc(pm8001_ha, ent))
 		return pm8001_ha;
+failed_pci_alloc:
 	pm8001_free(pm8001_ha);
 	return NULL;
 }
diff --git a/drivers/scsi/pm8001/pm80xx_hwi.c b/drivers/scsi/pm8001/pm80xx_hwi.c
index 86a3d483749c..7d0eada11d3c 100644
--- a/drivers/scsi/pm8001/pm80xx_hwi.c
+++ b/drivers/scsi/pm8001/pm80xx_hwi.c
@@ -1115,7 +1115,7 @@  static int check_fw_ready(struct pm8001_hba_info *pm8001_ha)
 	return ret;
 }
 
-static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
+static int init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
 {
 	void __iomem *base_addr;
 	u32	value;
@@ -1124,15 +1124,48 @@  static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
 	u32	pcilogic;
 
 	value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0);
+
+	/**
+	 * lower 26 bits of SCRATCHPAD0 register describes offset within the
+	 * PCIe BAR where the MPI configuration table is present
+	 */
 	offset = value & 0x03FFFFFF; /* scratch pad 0 TBL address */
 
 	pm8001_dbg(pm8001_ha, DEV, "Scratchpad 0 Offset: 0x%x value 0x%x\n",
 		   offset, value);
+	/**
+	 * Upper 6 bits describe the offset within PCI config space where BAR
+	 * is located.
+	 */
 	pcilogic = (value & 0xFC000000) >> 26;
 	pcibar = get_pci_bar_index(pcilogic);
 	pm8001_dbg(pm8001_ha, INIT, "Scratchpad 0 PCI BAR: %d\n", pcibar);
+
+	/**
+	 * Make sure the offset falls inside the ioremapped PCI BAR
+	 */
+	if (offset > pm8001_ha->io_mem[pcibar].memsize) {
+		pm8001_dbg(pm8001_ha, FAIL,
+			"Main cfg tbl offset outside %u > %u\n",
+				offset, pm8001_ha->io_mem[pcibar].memsize);
+		return -EBUSY;
+	}
 	pm8001_ha->main_cfg_tbl_addr = base_addr =
 		pm8001_ha->io_mem[pcibar].memvirtaddr + offset;
+
+	/**
+	 * Validate main configuration table address: first DWord should read
+	 * "PMCS"
+	 */
+	value = pm8001_mr32(pm8001_ha->main_cfg_tbl_addr, 0);
+	if (memcmp(&value, "PMCS", 4) != 0) {
+		pm8001_dbg(pm8001_ha, FAIL,
+			"BAD main config signature 0x%x\n",
+				value);
+		return -EBUSY;
+	}
+	pm8001_dbg(pm8001_ha, INIT,
+			"VALID main config signature 0x%x\n", value);
 	pm8001_ha->general_stat_tbl_addr =
 		base_addr + (pm8001_cr32(pm8001_ha, pcibar, offset + 0x18) &
 					0xFFFFFF);
@@ -1171,6 +1204,7 @@  static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha)
 	pm8001_dbg(pm8001_ha, INIT, "addr - pspa %p ivt %p\n",
 		   pm8001_ha->pspa_q_tbl_addr,
 		   pm8001_ha->ivt_tbl_addr);
+	return 0;
 }
 
 /**
@@ -1438,7 +1472,12 @@  static int pm80xx_chip_init(struct pm8001_hba_info *pm8001_ha)
 	pm8001_ha->controller_fatal_error = false;
 
 	/* Initialize pci space address eg: mpi offset */
-	init_pci_device_addresses(pm8001_ha);
+	ret = init_pci_device_addresses(pm8001_ha);
+	if (ret) {
+		pm8001_dbg(pm8001_ha, FAIL,
+			"Failed to init pci addresses");
+		return ret;
+	}
 	init_default_table_values(pm8001_ha);
 	read_main_config_table(pm8001_ha);
 	read_general_status_table(pm8001_ha);
@@ -1482,7 +1521,15 @@  static int mpi_uninit_check(struct pm8001_hba_info *pm8001_ha)
 	u32 max_wait_count;
 	u32 value;
 	u32 gst_len_mpistate;
-	init_pci_device_addresses(pm8001_ha);
+	int ret;
+
+	ret = init_pci_device_addresses(pm8001_ha);
+	if (ret) {
+		pm8001_dbg(pm8001_ha, FAIL,
+			"Failed to init pci addresses");
+		return ret;
+	}
+
 	/* Write bit1=1 to Inbound DoorBell Register to tell the SPC FW the
 	table is stop */
 	pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPCv_MSGU_CFG_TABLE_RESET);