diff mbox series

[v3,09/15] spi: bcm63xx-hsspi: Handle cs_change correctly

Message ID 20230207065826.285013-10-william.zhang@broadcom.com
State Superseded
Headers show
Series spi: bcm63xx-hsspi: driver and doc updates | expand

Commit Message

William Zhang Feb. 7, 2023, 6:58 a.m. UTC
The kernel SPI interface includes the cs_change flag that alters how
the CS behaves.

If we're in the middle of transfers, it tells us to unselect the
CS momentarily since the target device requires that.

If we're at the end of a transfer, it tells us to keep the CS
selected, perhaps because the next transfer is likely targeted
to the same device.

We implement this scheme in the HSSPI driver in this change.

Prior to this change, the CS would toggle momentarily if cs_change
was set for the last transfer. This can be ignored by some or
most devices, but the Microchip TPM2 device does not ignore it.

With the change, the behavior is corrected and the 'glitch' is
eliminated.

Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: William Zhang <william.zhang@broadcom.com>

---

Changes in v3:
- Use the cs_change and cs_off logic from SPI core
spi_transfer_one_message function

Changes in v2:
- Fix unused variable ‘reg’ compile warning

 drivers/spi/spi-bcm63xx-hsspi.c | 33 +++++++++++++++++++++++----------
 1 file changed, 23 insertions(+), 10 deletions(-)
diff mbox series

Patch

diff --git a/drivers/spi/spi-bcm63xx-hsspi.c b/drivers/spi/spi-bcm63xx-hsspi.c
index 55cbe7deba08..af51488659b8 100644
--- a/drivers/spi/spi-bcm63xx-hsspi.c
+++ b/drivers/spi/spi-bcm63xx-hsspi.c
@@ -219,7 +219,8 @@  static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t)
 	unsigned long limit;
 
 	bcm63xx_hsspi_set_clk(bs, spi, t->speed_hz);
-	bcm63xx_hsspi_set_cs(bs, spi->chip_select, true);
+	if (!t->cs_off)
+		bcm63xx_hsspi_set_cs(bs, spi->chip_select, true);
 
 	if (tx && rx)
 		opcode = HSSPI_OP_READ_WRITE;
@@ -338,7 +339,7 @@  static int bcm63xx_hsspi_transfer_one(struct spi_master *master,
 	struct spi_device *spi = msg->spi;
 	int status = -EINVAL;
 	int dummy_cs;
-	u32 reg;
+	bool keep_cs = false;
 
 	mutex_lock(&bs->msg_mutex);
 	/* This controller does not support keeping CS active during idle.
@@ -367,16 +368,28 @@  static int bcm63xx_hsspi_transfer_one(struct spi_master *master,
 
 		spi_transfer_delay_exec(t);
 
-		if (t->cs_change)
-			bcm63xx_hsspi_set_cs(bs, spi->chip_select, false);
+		/* use existing cs change logic from spi_transfer_one_message */
+		if (t->cs_change) {
+			if (list_is_last(&t->transfer_list, &msg->transfers)) {
+				keep_cs = true;
+			} else {
+				if (!t->cs_off)
+					bcm63xx_hsspi_set_cs(bs, spi->chip_select, false);
+
+				spi_transfer_cs_change_delay_exec(msg, t);
+
+				if (!list_next_entry(t, transfer_list)->cs_off)
+					bcm63xx_hsspi_set_cs(bs, spi->chip_select, true);
+			}
+		} else if (!list_is_last(&t->transfer_list, &msg->transfers) &&
+			   t->cs_off != list_next_entry(t, transfer_list)->cs_off) {
+			bcm63xx_hsspi_set_cs(bs, spi->chip_select, t->cs_off);
+		}
 	}
 
-	mutex_lock(&bs->bus_mutex);
-	reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
-	reg &= ~GLOBAL_CTRL_CS_POLARITY_MASK;
-	reg |= bs->cs_polarity;
-	__raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG);
-	mutex_unlock(&bs->bus_mutex);
+	bcm63xx_hsspi_set_cs(bs, dummy_cs, false);
+	if (status || !keep_cs)
+		bcm63xx_hsspi_set_cs(bs, spi->chip_select, false);
 
 	mutex_unlock(&bs->msg_mutex);
 	msg->status = status;