diff mbox series

[10/18] dt-bindings: usb: Convert DWC USB3 bindings to DT schema

Message ID 20201010224121.12672-11-Sergey.Semin@baikalelectronics.ru
State Superseded
Headers show
Series dt-bindings: usb: Add generic USB HCD, xHCI, DWC USB3 DT schema | expand

Commit Message

Serge Semin Oct. 10, 2020, 10:41 p.m. UTC 
DWC USB3 DT node is supposed to be compliant with the Generic xHCI
Controller schema, but with additional vendor-specific properties, the
controller-specific reference clocks and PHYs. So let's convert the
currently available legacy text-based DWC USB3 bindings to the DT schema
and make sure the DWC USB3 nodes are also validated against the
usb-xhci.yaml schema.

Note we have to discard the nodename restriction of being prefixed with
"dwc3@" string, since in accordance with the usb-hcd.yaml schema USB nodes
are supposed to be named as "^usb(@.*)".

Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>

---

Alas applying the usb-hcd.yaml schema on the DWC USB3 nodes will cause
dtbs_check failures since a lot of "snps,dwc3"-compatible DT nodes are
named with prefixes like "^dwc3@", "^usb[0-9]@" and even "^dwusb@", while
usb-hcd.yaml permits the "^usb@" prefix only. As I see it the better but
more painful solution would be to fix the corresponding DTS files (it's
some of the Qualcomm, HiSilicon, Exynos, Allwinner, Omap, Stih, APM and
Freescale DTS'es) so the DWC USB3 DT nodes would comply with the generic
USB HCD node naming schema. Alternatively we could either extend the
naming space in the usb-hcd.yaml or extract the generic properties to a
dedicated DT schema file. What do you think?
---
 .../devicetree/bindings/usb/dwc3.txt          | 125 --------
 .../devicetree/bindings/usb/snps,dwc3.yaml    | 295 ++++++++++++++++++
 2 files changed, 295 insertions(+), 125 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/usb/dwc3.txt
 create mode 100644 Documentation/devicetree/bindings/usb/snps,dwc3.yaml

Comments

Rob Herring Oct. 13, 2020, 12:36 p.m. UTC | #1 
On Sun, Oct 11, 2020 at 01:41:13AM +0300, Serge Semin wrote:
> DWC USB3 DT node is supposed to be compliant with the Generic xHCI
> Controller schema, but with additional vendor-specific properties, the
> controller-specific reference clocks and PHYs. So let's convert the
> currently available legacy text-based DWC USB3 bindings to the DT schema
> and make sure the DWC USB3 nodes are also validated against the
> usb-xhci.yaml schema.
> 
> Note we have to discard the nodename restriction of being prefixed with
> "dwc3@" string, since in accordance with the usb-hcd.yaml schema USB nodes
> are supposed to be named as "^usb(@.*)".
> 
> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
> 
> ---
> 
> Alas applying the usb-hcd.yaml schema on the DWC USB3 nodes will cause
> dtbs_check failures since a lot of "snps,dwc3"-compatible DT nodes are
> named with prefixes like "^dwc3@", "^usb[0-9]@" and even "^dwusb@", while
> usb-hcd.yaml permits the "^usb@" prefix only. As I see it the better but
> more painful solution would be to fix the corresponding DTS files (it's
> some of the Qualcomm, HiSilicon, Exynos, Allwinner, Omap, Stih, APM and
> Freescale DTS'es) so the DWC USB3 DT nodes would comply with the generic
> USB HCD node naming schema. Alternatively we could either extend the
> naming space in the usb-hcd.yaml or extract the generic properties to a
> dedicated DT schema file. What do you think?

IMO, we should fix the node names.

> ---
>  .../devicetree/bindings/usb/dwc3.txt          | 125 --------
>  .../devicetree/bindings/usb/snps,dwc3.yaml    | 295 ++++++++++++++++++
>  2 files changed, 295 insertions(+), 125 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/usb/dwc3.txt
>  create mode 100644 Documentation/devicetree/bindings/usb/snps,dwc3.yaml
> 
> diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
> deleted file mode 100644
> index d03edf9d3935..000000000000
> --- a/Documentation/devicetree/bindings/usb/dwc3.txt
> +++ /dev/null
> @@ -1,125 +0,0 @@
> -synopsys DWC3 CORE
> -
> -DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
> -      as described in 'usb/generic.txt'
> -
> -Required properties:
> - - compatible: must be "snps,dwc3"
> - - reg : Address and length of the register set for the device
> - - interrupts: Interrupts used by the dwc3 controller.
> - - clock-names: list of clock names. Ideally should be "ref",
> -                "bus_early", "suspend" but may be less or more.
> - - clocks: list of phandle and clock specifier pairs corresponding to
> -           entries in the clock-names property.
> -
> -Exception for clocks:
> -  clocks are optional if the parent node (i.e. glue-layer) is compatible to
> -  one of the following:
> -    "cavium,octeon-7130-usb-uctl"
> -    "qcom,dwc3"
> -    "samsung,exynos5250-dwusb3"
> -    "samsung,exynos5433-dwusb3"
> -    "samsung,exynos7-dwusb3"
> -    "sprd,sc9860-dwc3"
> -    "st,stih407-dwc3"
> -    "ti,am437x-dwc3"
> -    "ti,dwc3"
> -    "ti,keystone-dwc3"
> -    "rockchip,rk3399-dwc3"
> -    "xlnx,zynqmp-dwc3"
> -
> -Optional properties:
> - - usb-phy : array of phandle for the PHY device.  The first element
> -   in the array is expected to be a handle to the USB2/HS PHY and
> -   the second element is expected to be a handle to the USB3/SS PHY
> - - phys: from the *Generic PHY* bindings
> - - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy"
> -	or "usb3-phy".
> - - resets: set of phandle and reset specifier pairs
> - - snps,usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM
> - - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
> - - snps,dis-start-transfer-quirk: when set, disable isoc START TRANSFER command
> -			failure SW work-around for DWC_usb31 version 1.70a-ea06
> -			and prior.
> - - snps,disable_scramble_quirk: true when SW should disable data scrambling.
> -	Only really useful for FPGA builds.
> - - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled
> - - snps,lpm-nyet-threshold: LPM NYET threshold
> - - snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk
> - - snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
> - - snps,req_p1p2p3_quirk: when set, the core will always request for
> -			P1/P2/P3 transition sequence.
> - - snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain
> -			amount of 8B10B errors occur.
> - - snps,del_phy_power_chg_quirk: when set core will delay PHY power change
> -			from P0 to P1/P2/P3.
> - - snps,lfps_filter_quirk: when set core will filter LFPS reception.
> - - snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start
> -			Polling LFPS after RX.Detect.
> - - snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value.
> - - snps,tx_de_emphasis: the value driven to the PHY is controlled by the
> -			LTSSM during USB3 Compliance mode.
> - - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
> - - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
> - - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
> -			disabling the suspend signal to the PHY.
> - - snps,dis-u1-entry-quirk: set if link entering into U1 needs to be disabled.
> - - snps,dis-u2-entry-quirk: set if link entering into U2 needs to be disabled.
> - - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection
> -			in PHY P3 power state.
> - - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists
> -			in GUSB2PHYCFG, specify that USB2 PHY doesn't provide
> -			a free-running PHY clock.
> - - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power
> -			from P0 to P1/P2/P3 without delay.
> - - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check
> -			during HS transmit.
> - - snps,parkmode-disable-ss-quirk: when set, all SuperSpeed bus instances in
> -			park mode are disabled.
> - - snps,dis_metastability_quirk: when set, disable metastability workaround.
> -			CAUTION: use only if you are absolutely sure of it.
> - - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
> -			utmi_l1_suspend_n, false when asserts utmi_sleep_n
> - - snps,hird-threshold: HIRD threshold
> - - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
> -   UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
> - - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
> -	register for post-silicon frame length adjustment when the
> -	fladj_30mhz_sdbnd signal is invalid or incorrect.
> - - snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode
> -			only. Set this and rx-max-burst-prd to a valid,
> -			non-zero value 1-16 (DWC_usb31 programming guide
> -			section 1.2.4) to enable periodic ESS RX threshold.
> - - snps,rx-max-burst-prd: max periodic ESS RX burst size - host mode only. Set
> -			this and rx-thr-num-pkt-prd to a valid, non-zero value
> -			1-16 (DWC_usb31 programming guide section 1.2.4) to
> -			enable periodic ESS RX threshold.
> - - snps,tx-thr-num-pkt-prd: periodic ESS TX packet threshold count - host mode
> -			only. Set this and tx-max-burst-prd to a valid,
> -			non-zero value 1-16 (DWC_usb31 programming guide
> -			section 1.2.3) to enable periodic ESS TX threshold.
> - - snps,tx-max-burst-prd: max periodic ESS TX burst size - host mode only. Set
> -			this and tx-thr-num-pkt-prd to a valid, non-zero value
> -			1-16 (DWC_usb31 programming guide section 1.2.3) to
> -			enable periodic ESS TX threshold.
> -
> - - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.
> - - snps,incr-burst-type-adjustment: Value for INCR burst type of GSBUSCFG0
> -			register, undefined length INCR burst type enable and INCRx type.
> -			When just one value, which means INCRX burst mode enabled. When
> -			more than one value, which means undefined length INCR burst type
> -			enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256.
> -
> - - in addition all properties from usb-xhci.txt from the current directory are
> -   supported as well
> -
> -
> -This is usually a subnode to DWC3 glue to which it is connected.
> -
> -dwc3@4a030000 {
> -	compatible = "snps,dwc3";
> -	reg = <0x4a030000 0xcfff>;
> -	interrupts = <0 92 4>
> -	usb-phy = <&usb2_phy>, <&usb3,phy>;
> -	snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
> -};
> diff --git a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
> new file mode 100644
> index 000000000000..24808fc2c7e3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
> @@ -0,0 +1,295 @@
> +# SPDX-License-Identifier: GPL-2.0
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Synopsys DesignWare USB3 Controller
> +
> +maintainers:
> +  - Felipe Balbi <balbi@kernel.org>
> +
> +description: |
> +  This is usually a subnode to DWC3 glue to which it is connected, but can also
> +  be presented as a standalone DT node with an optional vendor-specific
> +  compatible string.
> +
> +allOf:
> +  - $ref: "usb-xhci.yaml#"
> +
> +properties:
> +  compatible:
> +    contains:
> +      const: "snps,dwc3"

Don't need quotes

> +
> +  interrupts:
> +    minItems: 1
> +    maxItems: 3
> +
> +  clocks:
> +    description: |
> +      In general the core supports three types of clocks. bus_clk_early is a

s/bus_clk_early/bus_early/

And the others too.

> +      SoC Bus Clock (AHB/AXI/Native). ref_clk generates ITP when the UTMI/ULPI
> +      PHY is suspended. suspend_clk clocks a small part of the USB3 core when
> +      SS PHY in P3. But particular cases may differ from that having less or
> +      more clock sources with another names.
> +
> +  clock-names:
> +    contains:
> +      anyOf:
> +        - enum: ["bus_early", "ref", "suspend"]
> +        - true

That's unfortunate...

> +
> +  usb-phy:
> +   minItems: 1
> +   items:
> +     - description: USB2/HS PHY
> +     - description: USB3/SS PHY
> +
> +  phys:
> +    minItems: 1
> +    items:
> +      - description: USB2/HS PHY
> +      - description: USB3/SS PHY
> +
> +  phy-names:
> +    minItems: 1
> +    items:
> +      - const: usb2-phy
> +      - const: usb3-phy
> +
> +  resets:
> +    minItems: 1
> +
> +  snps,usb2-lpm-disable:
> +    description: Indicate if we don't want to enable USB2 HW LPM
> +    type: boolean
> +
> +  snps,usb3_lpm_capable:
> +    description: Determines if platform is USB3 LPM capable
> +    type: boolean
> +
> +  snps,dis-start-transfer-quirk:
> +    description: |

Drop '|'.

> +      When set, disable isoc START TRANSFER command failure SW work-around
> +      for DWC_usb31 version 1.70a-ea06 and prior.
> +    type: boolean
> +
> +  snps,disable_scramble_quirk:
> +    description: |
> +      True when SW should disable data scrambling. Only really useful for FPGA
> +      builds.
> +    type: boolean
> +
> +  snps,has-lpm-erratum:
> +    description: True when DWC3 was configured with LPM Erratum enabled
> +    type: boolean
> +
> +  snps,lpm-nyet-threshold:
> +    description: LPM NYET threshold
> +    $ref: /schemas/types.yaml#/definitions/uint8
> +
> +  snps,u2exit_lfps_quirk:
> +    description: Set if we want to enable u2exit lfps quirk
> +    type: boolean
> +
> +  snps,u2ss_inp3_quirk:
> +    description: Set if we enable P3 OK for U2/SS Inactive quirk
> +    type: boolean
> +
> +  snps,req_p1p2p3_quirk:
> +    description: |
> +      When set, the core will always request for P1/P2/P3 transition sequence.
> +    type: boolean
> +
> +  snps,del_p1p2p3_quirk:
> +    description: |
> +      When set core will delay P1/P2/P3 until a certain amount of 8B10B errors
> +      occur.
> +    type: boolean
> +
> +  snps,del_phy_power_chg_quirk:
> +    description: When set core will delay PHY power change from P0 to P1/P2/P3.
> +    type: boolean
> +
> +  snps,lfps_filter_quirk:
> +    description: When set core will filter LFPS reception.
> +    type: boolean
> +
> +  snps,rx_detect_poll_quirk:
> +    description: |
> +      when set core will disable a 400us delay to start Polling LFPS after
> +      RX.Detect.
> +    type: boolean
> +
> +  snps,tx_de_emphasis_quirk:
> +    description: When set core will set Tx de-emphasis value
> +    type: boolean
> +
> +  snps,tx_de_emphasis:
> +    description: |
> +      The value driven to the PHY is controlled by the LTSSM during USB3
> +      Compliance mode.
> +    $ref: /schemas/types.yaml#/definitions/uint8
> +
> +  snps,dis_u3_susphy_quirk:
> +    description: When set core will disable USB3 suspend phy
> +    type: boolean
> +
> +  snps,dis_u2_susphy_quirk:
> +    description: When set core will disable USB2 suspend phy
> +    type: boolean
> +
> +  snps,dis_enblslpm_quirk:
> +    description: |
> +      When set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal
> +      to the PHY.
> +    type: boolean
> +
> +  snps,dis-u1-entry-quirk:
> +    description: Set if link entering into U1 needs to be disabled
> +    type: boolean
> +
> +  snps,dis-u2-entry-quirk:
> +    description: Set if link entering into U2 needs to be disabled
> +    type: boolean
> +
> +  snps,dis_rxdet_inp3_quirk:
> +    description: |
> +      When set core will disable receiver detection in PHY P3 power state.
> +    type: boolean
> +
> +  snps,dis-u2-freeclk-exists-quirk:
> +    description: |
> +      When set, clear the u2_freeclk_exists in GUSB2PHYCFG, specify that USB2
> +      PHY doesn't provide a free-running PHY clock.
> +    type: boolean
> +
> +  snps,dis-del-phy-power-chg-quirk:
> +    description: |
> +      When set core will change PHY power from P0 to P1/P2/P3 without delay.
> +    type: boolean
> +
> +  snps,dis-tx-ipgap-linecheck-quirk:
> +    description: When set, disable u2mac linestate check during HS transmit
> +    type: boolean
> +
> +  snps,parkmode-disable-ss-quirk:
> +    description: |
> +      When set, all SuperSpeed bus instances in park mode are disabled.
> +    type: boolean
> +
> +  snps,dis_metastability_quirk:
> +    description: |
> +      When set, disable metastability workaround. CAUTION! Use only if you are
> +      absolutely sure of it.
> +    type: boolean
> +
> +  snps,is-utmi-l1-suspend:
> +    description: |
> +      True when DWC3 asserts output signal utmi_l1_suspend_n, false when
> +      asserts utmi_sleep_n.
> +    type: boolean
> +
> +  snps,hird-threshold:
> +    description: HIRD threshold
> +    $ref: /schemas/types.yaml#/definitions/uint8
> +
> +  snps,hsphy_interface:
> +    description: |
> +      High-Speed PHY interface selection between UTMI+ and ULPI when the
> +      DWC_USB3_HSPHY_INTERFACE has value 3.
> +    $ref: /schemas/types.yaml#/definitions/uint8
> +    enum: ["utmi", "ulpi"]
> +
> +  snps,quirk-frame-length-adjustment:
> +    description: |
> +      Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame
> +      length adjustment when the fladj_30mhz_sdbnd signal is invalid or
> +      incorrect.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +
> +  snps,rx-thr-num-pkt-prd:
> +    description: |
> +      Periodic ESS RX packet threshold count (host mode only). Set this and
> +      snps,rx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31
> +      programming guide section 1.2.4) to enable periodic ESS RX threshold.
> +    $ref: /schemas/types.yaml#/definitions/uint8
> +    minimum: 1
> +    maximum: 16
> +
> +  snps,rx-max-burst-prd:
> +    description: |
> +      Max periodic ESS RX burst size (host mode only). Set this and
> +      snps,rx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31
> +      programming guide section 1.2.4) to enable periodic ESS RX threshold.
> +    $ref: /schemas/types.yaml#/definitions/uint8
> +    minimum: 1
> +    maximum: 16
> +
> +  snps,tx-thr-num-pkt-prd:
> +    description: |
> +      Periodic ESS TX packet threshold count (host mode only). Set this and
> +      snps,tx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31
> +      programming guide section 1.2.3) to enable periodic ESS TX threshold.
> +    $ref: /schemas/types.yaml#/definitions/uint8
> +    minimum: 1
> +    maximum: 16
> +
> +  snps,tx-max-burst-prd:
> +    description: |
> +      Max periodic ESS TX burst size (host mode only). Set this and
> +      snps,tx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31
> +      programming guide section 1.2.3) to enable periodic ESS TX threshold.
> +    $ref: /schemas/types.yaml#/definitions/uint8
> +    minimum: 1
> +    maximum: 16
> +
> +  tx-fifo-resize:
> +    description: Determines if the FIFO *has* to be reallocated
> +    deprecated: true
> +    type: boolean
> +
> +  snps,incr-burst-type-adjustment:
> +    description: |
> +      Value for INCR burst type of GSBUSCFG0 register, undefined length INCR
> +      burst type enable and INCRx type. A single value means INCRX burst mode
> +      enabled. If more than one value specified, undefined length INCR burst
> +      type will be enabled with burst lengths utilized up to the maximum
> +      of the values passed in this property.
> +    $ref: /schemas/types.yaml#/definitions/uint32-array
> +    minItems: 1
> +    maxItems: 8
> +    uniqueItems: true
> +    items:
> +      enum: [1, 4, 8, 16, 32, 64, 128, 256]
> +
> +unevaluatedProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +
> +examples:
> +  - |
> +    usb@4a030000 {
> +      compatible = "snps,dwc3";
> +      reg = <0x4a030000 0xcfff>;
> +      interrupts = <0 92 4>;
> +      usb-phy = <&usb2_phy>, <&usb3_phy>;
> +      snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
> +    };
> +  - |
> +    usb@4a000000 {
> +      compatible = "snps,dwc3";
> +      reg = <0x4a000000 0xcfff>;
> +      interrupts = <0 92 4>;
> +      clocks = <&clk 1>, <&clk 2>, <&clk 3>;
> +      clock-names = "bus_early", "ref", "suspend";
> +      phys = <&usb2_phy>, <&usb3_phy>;
> +      phy-names = "usb2-phy", "usb3-phy";
> +      snps,dis_u2_susphy_quirk;
> +      snps,dis_enblslpm_quirk;
> +    };
> +...
> -- 
> 2.27.0
>
Serge Semin Oct. 13, 2020, 3:16 p.m. UTC | #2 
On Tue, Oct 13, 2020 at 07:36:24AM -0500, Rob Herring wrote:
> On Sun, Oct 11, 2020 at 01:41:13AM +0300, Serge Semin wrote:
> > DWC USB3 DT node is supposed to be compliant with the Generic xHCI
> > Controller schema, but with additional vendor-specific properties, the
> > controller-specific reference clocks and PHYs. So let's convert the
> > currently available legacy text-based DWC USB3 bindings to the DT schema
> > and make sure the DWC USB3 nodes are also validated against the
> > usb-xhci.yaml schema.
> > 
> > Note we have to discard the nodename restriction of being prefixed with
> > "dwc3@" string, since in accordance with the usb-hcd.yaml schema USB nodes
> > are supposed to be named as "^usb(@.*)".
> > 
> > Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
> > 
> > ---
> > 
> > Alas applying the usb-hcd.yaml schema on the DWC USB3 nodes will cause
> > dtbs_check failures since a lot of "snps,dwc3"-compatible DT nodes are
> > named with prefixes like "^dwc3@", "^usb[0-9]@" and even "^dwusb@", while
> > usb-hcd.yaml permits the "^usb@" prefix only. As I see it the better but
> > more painful solution would be to fix the corresponding DTS files (it's
> > some of the Qualcomm, HiSilicon, Exynos, Allwinner, Omap, Stih, APM and
> > Freescale DTS'es) so the DWC USB3 DT nodes would comply with the generic
> > USB HCD node naming schema. Alternatively we could either extend the
> > naming space in the usb-hcd.yaml or extract the generic properties to a
> > dedicated DT schema file. What do you think?
> 

> IMO, we should fix the node names.

Ok. I'll attach a new patch to the series, which will fix it for all uncompatible
nodes. (Though the node with "^dwusb@" has got a comment, that the node-name
should be like that due to some compatibility reasons...)

> 
> > ---
> >  .../devicetree/bindings/usb/dwc3.txt          | 125 --------
> >  .../devicetree/bindings/usb/snps,dwc3.yaml    | 295 ++++++++++++++++++
> >  2 files changed, 295 insertions(+), 125 deletions(-)
> >  delete mode 100644 Documentation/devicetree/bindings/usb/dwc3.txt
> >  create mode 100644 Documentation/devicetree/bindings/usb/snps,dwc3.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
> > deleted file mode 100644
> > index d03edf9d3935..000000000000
> > --- a/Documentation/devicetree/bindings/usb/dwc3.txt
> > +++ /dev/null
> > @@ -1,125 +0,0 @@
> > -synopsys DWC3 CORE
> > -
> > -DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
> > -      as described in 'usb/generic.txt'
> > -
> > -Required properties:
> > - - compatible: must be "snps,dwc3"
> > - - reg : Address and length of the register set for the device
> > - - interrupts: Interrupts used by the dwc3 controller.
> > - - clock-names: list of clock names. Ideally should be "ref",
> > -                "bus_early", "suspend" but may be less or more.
> > - - clocks: list of phandle and clock specifier pairs corresponding to
> > -           entries in the clock-names property.
> > -
> > -Exception for clocks:
> > -  clocks are optional if the parent node (i.e. glue-layer) is compatible to
> > -  one of the following:
> > -    "cavium,octeon-7130-usb-uctl"
> > -    "qcom,dwc3"
> > -    "samsung,exynos5250-dwusb3"
> > -    "samsung,exynos5433-dwusb3"
> > -    "samsung,exynos7-dwusb3"
> > -    "sprd,sc9860-dwc3"
> > -    "st,stih407-dwc3"
> > -    "ti,am437x-dwc3"
> > -    "ti,dwc3"
> > -    "ti,keystone-dwc3"
> > -    "rockchip,rk3399-dwc3"
> > -    "xlnx,zynqmp-dwc3"
> > -
> > -Optional properties:
> > - - usb-phy : array of phandle for the PHY device.  The first element
> > -   in the array is expected to be a handle to the USB2/HS PHY and
> > -   the second element is expected to be a handle to the USB3/SS PHY
> > - - phys: from the *Generic PHY* bindings
> > - - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy"
> > -	or "usb3-phy".
> > - - resets: set of phandle and reset specifier pairs
> > - - snps,usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM
> > - - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
> > - - snps,dis-start-transfer-quirk: when set, disable isoc START TRANSFER command
> > -			failure SW work-around for DWC_usb31 version 1.70a-ea06
> > -			and prior.
> > - - snps,disable_scramble_quirk: true when SW should disable data scrambling.
> > -	Only really useful for FPGA builds.
> > - - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled
> > - - snps,lpm-nyet-threshold: LPM NYET threshold
> > - - snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk
> > - - snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
> > - - snps,req_p1p2p3_quirk: when set, the core will always request for
> > -			P1/P2/P3 transition sequence.
> > - - snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain
> > -			amount of 8B10B errors occur.
> > - - snps,del_phy_power_chg_quirk: when set core will delay PHY power change
> > -			from P0 to P1/P2/P3.
> > - - snps,lfps_filter_quirk: when set core will filter LFPS reception.
> > - - snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start
> > -			Polling LFPS after RX.Detect.
> > - - snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value.
> > - - snps,tx_de_emphasis: the value driven to the PHY is controlled by the
> > -			LTSSM during USB3 Compliance mode.
> > - - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
> > - - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
> > - - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
> > -			disabling the suspend signal to the PHY.
> > - - snps,dis-u1-entry-quirk: set if link entering into U1 needs to be disabled.
> > - - snps,dis-u2-entry-quirk: set if link entering into U2 needs to be disabled.
> > - - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection
> > -			in PHY P3 power state.
> > - - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists
> > -			in GUSB2PHYCFG, specify that USB2 PHY doesn't provide
> > -			a free-running PHY clock.
> > - - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power
> > -			from P0 to P1/P2/P3 without delay.
> > - - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check
> > -			during HS transmit.
> > - - snps,parkmode-disable-ss-quirk: when set, all SuperSpeed bus instances in
> > -			park mode are disabled.
> > - - snps,dis_metastability_quirk: when set, disable metastability workaround.
> > -			CAUTION: use only if you are absolutely sure of it.
> > - - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
> > -			utmi_l1_suspend_n, false when asserts utmi_sleep_n
> > - - snps,hird-threshold: HIRD threshold
> > - - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
> > -   UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
> > - - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
> > -	register for post-silicon frame length adjustment when the
> > -	fladj_30mhz_sdbnd signal is invalid or incorrect.
> > - - snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode
> > -			only. Set this and rx-max-burst-prd to a valid,
> > -			non-zero value 1-16 (DWC_usb31 programming guide
> > -			section 1.2.4) to enable periodic ESS RX threshold.
> > - - snps,rx-max-burst-prd: max periodic ESS RX burst size - host mode only. Set
> > -			this and rx-thr-num-pkt-prd to a valid, non-zero value
> > -			1-16 (DWC_usb31 programming guide section 1.2.4) to
> > -			enable periodic ESS RX threshold.
> > - - snps,tx-thr-num-pkt-prd: periodic ESS TX packet threshold count - host mode
> > -			only. Set this and tx-max-burst-prd to a valid,
> > -			non-zero value 1-16 (DWC_usb31 programming guide
> > -			section 1.2.3) to enable periodic ESS TX threshold.
> > - - snps,tx-max-burst-prd: max periodic ESS TX burst size - host mode only. Set
> > -			this and tx-thr-num-pkt-prd to a valid, non-zero value
> > -			1-16 (DWC_usb31 programming guide section 1.2.3) to
> > -			enable periodic ESS TX threshold.
> > -
> > - - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.
> > - - snps,incr-burst-type-adjustment: Value for INCR burst type of GSBUSCFG0
> > -			register, undefined length INCR burst type enable and INCRx type.
> > -			When just one value, which means INCRX burst mode enabled. When
> > -			more than one value, which means undefined length INCR burst type
> > -			enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256.
> > -
> > - - in addition all properties from usb-xhci.txt from the current directory are
> > -   supported as well
> > -
> > -
> > -This is usually a subnode to DWC3 glue to which it is connected.
> > -
> > -dwc3@4a030000 {
> > -	compatible = "snps,dwc3";
> > -	reg = <0x4a030000 0xcfff>;
> > -	interrupts = <0 92 4>
> > -	usb-phy = <&usb2_phy>, <&usb3,phy>;
> > -	snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
> > -};
> > diff --git a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
> > new file mode 100644
> > index 000000000000..24808fc2c7e3
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
> > @@ -0,0 +1,295 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Synopsys DesignWare USB3 Controller
> > +
> > +maintainers:
> > +  - Felipe Balbi <balbi@kernel.org>
> > +
> > +description: |
> > +  This is usually a subnode to DWC3 glue to which it is connected, but can also
> > +  be presented as a standalone DT node with an optional vendor-specific
> > +  compatible string.
> > +
> > +allOf:
> > +  - $ref: "usb-xhci.yaml#"
> > +
> > +properties:
> > +  compatible:
> > +    contains:
> > +      const: "snps,dwc3"
> 

> Don't need quotes

Ok.

> 
> > +
> > +  interrupts:
> > +    minItems: 1
> > +    maxItems: 3
> > +
> > +  clocks:
> > +    description: |
> > +      In general the core supports three types of clocks. bus_clk_early is a
> 

> s/bus_clk_early/bus_early/
> 
> And the others too.

I doubted which clock names to use here, so I've utilized the names selected by the
core Databook for the corresponding clocks. Anyway. Ok. I'll replace them with the
strings enumerated below.

> 
> > +      SoC Bus Clock (AHB/AXI/Native). ref_clk generates ITP when the UTMI/ULPI
> > +      PHY is suspended. suspend_clk clocks a small part of the USB3 core when
> > +      SS PHY in P3. But particular cases may differ from that having less or
> > +      more clock sources with another names.
> > +
> > +  clock-names:
> > +    contains:
> > +      anyOf:
> > +        - enum: ["bus_early", "ref", "suspend"]
> > +        - true
> 

> That's unfortunate...

Yeah. That was the best schema I could come up with to get the original
bindings. Alas there are various clock-names have been used at some
DWC USB3-compatible DT nodes, so I couldn't just set a stricter restriction
here.

> 
> > +
> > +  usb-phy:
> > +   minItems: 1
> > +   items:
> > +     - description: USB2/HS PHY
> > +     - description: USB3/SS PHY
> > +
> > +  phys:
> > +    minItems: 1
> > +    items:
> > +      - description: USB2/HS PHY
> > +      - description: USB3/SS PHY
> > +
> > +  phy-names:
> > +    minItems: 1
> > +    items:
> > +      - const: usb2-phy
> > +      - const: usb3-phy
> > +
> > +  resets:
> > +    minItems: 1
> > +
> > +  snps,usb2-lpm-disable:
> > +    description: Indicate if we don't want to enable USB2 HW LPM
> > +    type: boolean
> > +
> > +  snps,usb3_lpm_capable:
> > +    description: Determines if platform is USB3 LPM capable
> > +    type: boolean
> > +
> > +  snps,dis-start-transfer-quirk:
> > +    description: |
> 

> Drop '|'.

Agreed.

-Sergey

> 
> > +      When set, disable isoc START TRANSFER command failure SW work-around
> > +      for DWC_usb31 version 1.70a-ea06 and prior.
> > +    type: boolean
> > +
> > +  snps,disable_scramble_quirk:
> > +    description: |
> > +      True when SW should disable data scrambling. Only really useful for FPGA
> > +      builds.
> > +    type: boolean
> > +
> > +  snps,has-lpm-erratum:
> > +    description: True when DWC3 was configured with LPM Erratum enabled
> > +    type: boolean
> > +
> > +  snps,lpm-nyet-threshold:
> > +    description: LPM NYET threshold
> > +    $ref: /schemas/types.yaml#/definitions/uint8
> > +
> > +  snps,u2exit_lfps_quirk:
> > +    description: Set if we want to enable u2exit lfps quirk
> > +    type: boolean
> > +
> > +  snps,u2ss_inp3_quirk:
> > +    description: Set if we enable P3 OK for U2/SS Inactive quirk
> > +    type: boolean
> > +
> > +  snps,req_p1p2p3_quirk:
> > +    description: |
> > +      When set, the core will always request for P1/P2/P3 transition sequence.
> > +    type: boolean
> > +
> > +  snps,del_p1p2p3_quirk:
> > +    description: |
> > +      When set core will delay P1/P2/P3 until a certain amount of 8B10B errors
> > +      occur.
> > +    type: boolean
> > +
> > +  snps,del_phy_power_chg_quirk:
> > +    description: When set core will delay PHY power change from P0 to P1/P2/P3.
> > +    type: boolean
> > +
> > +  snps,lfps_filter_quirk:
> > +    description: When set core will filter LFPS reception.
> > +    type: boolean
> > +
> > +  snps,rx_detect_poll_quirk:
> > +    description: |
> > +      when set core will disable a 400us delay to start Polling LFPS after
> > +      RX.Detect.
> > +    type: boolean
> > +
> > +  snps,tx_de_emphasis_quirk:
> > +    description: When set core will set Tx de-emphasis value
> > +    type: boolean
> > +
> > +  snps,tx_de_emphasis:
> > +    description: |
> > +      The value driven to the PHY is controlled by the LTSSM during USB3
> > +      Compliance mode.
> > +    $ref: /schemas/types.yaml#/definitions/uint8
> > +
> > +  snps,dis_u3_susphy_quirk:
> > +    description: When set core will disable USB3 suspend phy
> > +    type: boolean
> > +
> > +  snps,dis_u2_susphy_quirk:
> > +    description: When set core will disable USB2 suspend phy
> > +    type: boolean
> > +
> > +  snps,dis_enblslpm_quirk:
> > +    description: |
> > +      When set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal
> > +      to the PHY.
> > +    type: boolean
> > +
> > +  snps,dis-u1-entry-quirk:
> > +    description: Set if link entering into U1 needs to be disabled
> > +    type: boolean
> > +
> > +  snps,dis-u2-entry-quirk:
> > +    description: Set if link entering into U2 needs to be disabled
> > +    type: boolean
> > +
> > +  snps,dis_rxdet_inp3_quirk:
> > +    description: |
> > +      When set core will disable receiver detection in PHY P3 power state.
> > +    type: boolean
> > +
> > +  snps,dis-u2-freeclk-exists-quirk:
> > +    description: |
> > +      When set, clear the u2_freeclk_exists in GUSB2PHYCFG, specify that USB2
> > +      PHY doesn't provide a free-running PHY clock.
> > +    type: boolean
> > +
> > +  snps,dis-del-phy-power-chg-quirk:
> > +    description: |
> > +      When set core will change PHY power from P0 to P1/P2/P3 without delay.
> > +    type: boolean
> > +
> > +  snps,dis-tx-ipgap-linecheck-quirk:
> > +    description: When set, disable u2mac linestate check during HS transmit
> > +    type: boolean
> > +
> > +  snps,parkmode-disable-ss-quirk:
> > +    description: |
> > +      When set, all SuperSpeed bus instances in park mode are disabled.
> > +    type: boolean
> > +
> > +  snps,dis_metastability_quirk:
> > +    description: |
> > +      When set, disable metastability workaround. CAUTION! Use only if you are
> > +      absolutely sure of it.
> > +    type: boolean
> > +
> > +  snps,is-utmi-l1-suspend:
> > +    description: |
> > +      True when DWC3 asserts output signal utmi_l1_suspend_n, false when
> > +      asserts utmi_sleep_n.
> > +    type: boolean
> > +
> > +  snps,hird-threshold:
> > +    description: HIRD threshold
> > +    $ref: /schemas/types.yaml#/definitions/uint8
> > +
> > +  snps,hsphy_interface:
> > +    description: |
> > +      High-Speed PHY interface selection between UTMI+ and ULPI when the
> > +      DWC_USB3_HSPHY_INTERFACE has value 3.
> > +    $ref: /schemas/types.yaml#/definitions/uint8
> > +    enum: ["utmi", "ulpi"]
> > +
> > +  snps,quirk-frame-length-adjustment:
> > +    description: |
> > +      Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame
> > +      length adjustment when the fladj_30mhz_sdbnd signal is invalid or
> > +      incorrect.
> > +    $ref: /schemas/types.yaml#/definitions/uint32
> > +
> > +  snps,rx-thr-num-pkt-prd:
> > +    description: |
> > +      Periodic ESS RX packet threshold count (host mode only). Set this and
> > +      snps,rx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31
> > +      programming guide section 1.2.4) to enable periodic ESS RX threshold.
> > +    $ref: /schemas/types.yaml#/definitions/uint8
> > +    minimum: 1
> > +    maximum: 16
> > +
> > +  snps,rx-max-burst-prd:
> > +    description: |
> > +      Max periodic ESS RX burst size (host mode only). Set this and
> > +      snps,rx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31
> > +      programming guide section 1.2.4) to enable periodic ESS RX threshold.
> > +    $ref: /schemas/types.yaml#/definitions/uint8
> > +    minimum: 1
> > +    maximum: 16
> > +
> > +  snps,tx-thr-num-pkt-prd:
> > +    description: |
> > +      Periodic ESS TX packet threshold count (host mode only). Set this and
> > +      snps,tx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31
> > +      programming guide section 1.2.3) to enable periodic ESS TX threshold.
> > +    $ref: /schemas/types.yaml#/definitions/uint8
> > +    minimum: 1
> > +    maximum: 16
> > +
> > +  snps,tx-max-burst-prd:
> > +    description: |
> > +      Max periodic ESS TX burst size (host mode only). Set this and
> > +      snps,tx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31
> > +      programming guide section 1.2.3) to enable periodic ESS TX threshold.
> > +    $ref: /schemas/types.yaml#/definitions/uint8
> > +    minimum: 1
> > +    maximum: 16
> > +
> > +  tx-fifo-resize:
> > +    description: Determines if the FIFO *has* to be reallocated
> > +    deprecated: true
> > +    type: boolean
> > +
> > +  snps,incr-burst-type-adjustment:
> > +    description: |
> > +      Value for INCR burst type of GSBUSCFG0 register, undefined length INCR
> > +      burst type enable and INCRx type. A single value means INCRX burst mode
> > +      enabled. If more than one value specified, undefined length INCR burst
> > +      type will be enabled with burst lengths utilized up to the maximum
> > +      of the values passed in this property.
> > +    $ref: /schemas/types.yaml#/definitions/uint32-array
> > +    minItems: 1
> > +    maxItems: 8
> > +    uniqueItems: true
> > +    items:
> > +      enum: [1, 4, 8, 16, 32, 64, 128, 256]
> > +
> > +unevaluatedProperties: false
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - interrupts
> > +
> > +examples:
> > +  - |
> > +    usb@4a030000 {
> > +      compatible = "snps,dwc3";
> > +      reg = <0x4a030000 0xcfff>;
> > +      interrupts = <0 92 4>;
> > +      usb-phy = <&usb2_phy>, <&usb3_phy>;
> > +      snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
> > +    };
> > +  - |
> > +    usb@4a000000 {
> > +      compatible = "snps,dwc3";
> > +      reg = <0x4a000000 0xcfff>;
> > +      interrupts = <0 92 4>;
> > +      clocks = <&clk 1>, <&clk 2>, <&clk 3>;
> > +      clock-names = "bus_early", "ref", "suspend";
> > +      phys = <&usb2_phy>, <&usb3_phy>;
> > +      phy-names = "usb2-phy", "usb3-phy";
> > +      snps,dis_u2_susphy_quirk;
> > +      snps,dis_enblslpm_quirk;
> > +    };
> > +...
> > -- 
> > 2.27.0
> >
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
deleted file mode 100644
index d03edf9d3935..000000000000
--- a/Documentation/devicetree/bindings/usb/dwc3.txt
+++ /dev/null
@@ -1,125 +0,0 @@ 
-synopsys DWC3 CORE
-
-DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
-      as described in 'usb/generic.txt'
-
-Required properties:
- - compatible: must be "snps,dwc3"
- - reg : Address and length of the register set for the device
- - interrupts: Interrupts used by the dwc3 controller.
- - clock-names: list of clock names. Ideally should be "ref",
-                "bus_early", "suspend" but may be less or more.
- - clocks: list of phandle and clock specifier pairs corresponding to
-           entries in the clock-names property.
-
-Exception for clocks:
-  clocks are optional if the parent node (i.e. glue-layer) is compatible to
-  one of the following:
-    "cavium,octeon-7130-usb-uctl"
-    "qcom,dwc3"
-    "samsung,exynos5250-dwusb3"
-    "samsung,exynos5433-dwusb3"
-    "samsung,exynos7-dwusb3"
-    "sprd,sc9860-dwc3"
-    "st,stih407-dwc3"
-    "ti,am437x-dwc3"
-    "ti,dwc3"
-    "ti,keystone-dwc3"
-    "rockchip,rk3399-dwc3"
-    "xlnx,zynqmp-dwc3"
-
-Optional properties:
- - usb-phy : array of phandle for the PHY device.  The first element
-   in the array is expected to be a handle to the USB2/HS PHY and
-   the second element is expected to be a handle to the USB3/SS PHY
- - phys: from the *Generic PHY* bindings
- - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy"
-	or "usb3-phy".
- - resets: set of phandle and reset specifier pairs
- - snps,usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM
- - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
- - snps,dis-start-transfer-quirk: when set, disable isoc START TRANSFER command
-			failure SW work-around for DWC_usb31 version 1.70a-ea06
-			and prior.
- - snps,disable_scramble_quirk: true when SW should disable data scrambling.
-	Only really useful for FPGA builds.
- - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled
- - snps,lpm-nyet-threshold: LPM NYET threshold
- - snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk
- - snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk
- - snps,req_p1p2p3_quirk: when set, the core will always request for
-			P1/P2/P3 transition sequence.
- - snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain
-			amount of 8B10B errors occur.
- - snps,del_phy_power_chg_quirk: when set core will delay PHY power change
-			from P0 to P1/P2/P3.
- - snps,lfps_filter_quirk: when set core will filter LFPS reception.
- - snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start
-			Polling LFPS after RX.Detect.
- - snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value.
- - snps,tx_de_emphasis: the value driven to the PHY is controlled by the
-			LTSSM during USB3 Compliance mode.
- - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy.
- - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy.
- - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG,
-			disabling the suspend signal to the PHY.
- - snps,dis-u1-entry-quirk: set if link entering into U1 needs to be disabled.
- - snps,dis-u2-entry-quirk: set if link entering into U2 needs to be disabled.
- - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection
-			in PHY P3 power state.
- - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists
-			in GUSB2PHYCFG, specify that USB2 PHY doesn't provide
-			a free-running PHY clock.
- - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power
-			from P0 to P1/P2/P3 without delay.
- - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check
-			during HS transmit.
- - snps,parkmode-disable-ss-quirk: when set, all SuperSpeed bus instances in
-			park mode are disabled.
- - snps,dis_metastability_quirk: when set, disable metastability workaround.
-			CAUTION: use only if you are absolutely sure of it.
- - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal
-			utmi_l1_suspend_n, false when asserts utmi_sleep_n
- - snps,hird-threshold: HIRD threshold
- - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for
-   UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3.
- - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
-	register for post-silicon frame length adjustment when the
-	fladj_30mhz_sdbnd signal is invalid or incorrect.
- - snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode
-			only. Set this and rx-max-burst-prd to a valid,
-			non-zero value 1-16 (DWC_usb31 programming guide
-			section 1.2.4) to enable periodic ESS RX threshold.
- - snps,rx-max-burst-prd: max periodic ESS RX burst size - host mode only. Set
-			this and rx-thr-num-pkt-prd to a valid, non-zero value
-			1-16 (DWC_usb31 programming guide section 1.2.4) to
-			enable periodic ESS RX threshold.
- - snps,tx-thr-num-pkt-prd: periodic ESS TX packet threshold count - host mode
-			only. Set this and tx-max-burst-prd to a valid,
-			non-zero value 1-16 (DWC_usb31 programming guide
-			section 1.2.3) to enable periodic ESS TX threshold.
- - snps,tx-max-burst-prd: max periodic ESS TX burst size - host mode only. Set
-			this and tx-thr-num-pkt-prd to a valid, non-zero value
-			1-16 (DWC_usb31 programming guide section 1.2.3) to
-			enable periodic ESS TX threshold.
-
- - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated.
- - snps,incr-burst-type-adjustment: Value for INCR burst type of GSBUSCFG0
-			register, undefined length INCR burst type enable and INCRx type.
-			When just one value, which means INCRX burst mode enabled. When
-			more than one value, which means undefined length INCR burst type
-			enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256.
-
- - in addition all properties from usb-xhci.txt from the current directory are
-   supported as well
-
-
-This is usually a subnode to DWC3 glue to which it is connected.
-
-dwc3@4a030000 {
-	compatible = "snps,dwc3";
-	reg = <0x4a030000 0xcfff>;
-	interrupts = <0 92 4>
-	usb-phy = <&usb2_phy>, <&usb3,phy>;
-	snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
-};
diff --git a/Documentation/devicetree/bindings/usb/snps,dwc3.yaml b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
new file mode 100644
index 000000000000..24808fc2c7e3
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/snps,dwc3.yaml
@@ -0,0 +1,295 @@ 
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Synopsys DesignWare USB3 Controller
+
+maintainers:
+  - Felipe Balbi <balbi@kernel.org>
+
+description: |
+  This is usually a subnode to DWC3 glue to which it is connected, but can also
+  be presented as a standalone DT node with an optional vendor-specific
+  compatible string.
+
+allOf:
+  - $ref: "usb-xhci.yaml#"
+
+properties:
+  compatible:
+    contains:
+      const: "snps,dwc3"
+
+  interrupts:
+    minItems: 1
+    maxItems: 3
+
+  clocks:
+    description: |
+      In general the core supports three types of clocks. bus_clk_early is a
+      SoC Bus Clock (AHB/AXI/Native). ref_clk generates ITP when the UTMI/ULPI
+      PHY is suspended. suspend_clk clocks a small part of the USB3 core when
+      SS PHY in P3. But particular cases may differ from that having less or
+      more clock sources with another names.
+
+  clock-names:
+    contains:
+      anyOf:
+        - enum: ["bus_early", "ref", "suspend"]
+        - true
+
+  usb-phy:
+   minItems: 1
+   items:
+     - description: USB2/HS PHY
+     - description: USB3/SS PHY
+
+  phys:
+    minItems: 1
+    items:
+      - description: USB2/HS PHY
+      - description: USB3/SS PHY
+
+  phy-names:
+    minItems: 1
+    items:
+      - const: usb2-phy
+      - const: usb3-phy
+
+  resets:
+    minItems: 1
+
+  snps,usb2-lpm-disable:
+    description: Indicate if we don't want to enable USB2 HW LPM
+    type: boolean
+
+  snps,usb3_lpm_capable:
+    description: Determines if platform is USB3 LPM capable
+    type: boolean
+
+  snps,dis-start-transfer-quirk:
+    description: |
+      When set, disable isoc START TRANSFER command failure SW work-around
+      for DWC_usb31 version 1.70a-ea06 and prior.
+    type: boolean
+
+  snps,disable_scramble_quirk:
+    description: |
+      True when SW should disable data scrambling. Only really useful for FPGA
+      builds.
+    type: boolean
+
+  snps,has-lpm-erratum:
+    description: True when DWC3 was configured with LPM Erratum enabled
+    type: boolean
+
+  snps,lpm-nyet-threshold:
+    description: LPM NYET threshold
+    $ref: /schemas/types.yaml#/definitions/uint8
+
+  snps,u2exit_lfps_quirk:
+    description: Set if we want to enable u2exit lfps quirk
+    type: boolean
+
+  snps,u2ss_inp3_quirk:
+    description: Set if we enable P3 OK for U2/SS Inactive quirk
+    type: boolean
+
+  snps,req_p1p2p3_quirk:
+    description: |
+      When set, the core will always request for P1/P2/P3 transition sequence.
+    type: boolean
+
+  snps,del_p1p2p3_quirk:
+    description: |
+      When set core will delay P1/P2/P3 until a certain amount of 8B10B errors
+      occur.
+    type: boolean
+
+  snps,del_phy_power_chg_quirk:
+    description: When set core will delay PHY power change from P0 to P1/P2/P3.
+    type: boolean
+
+  snps,lfps_filter_quirk:
+    description: When set core will filter LFPS reception.
+    type: boolean
+
+  snps,rx_detect_poll_quirk:
+    description: |
+      when set core will disable a 400us delay to start Polling LFPS after
+      RX.Detect.
+    type: boolean
+
+  snps,tx_de_emphasis_quirk:
+    description: When set core will set Tx de-emphasis value
+    type: boolean
+
+  snps,tx_de_emphasis:
+    description: |
+      The value driven to the PHY is controlled by the LTSSM during USB3
+      Compliance mode.
+    $ref: /schemas/types.yaml#/definitions/uint8
+
+  snps,dis_u3_susphy_quirk:
+    description: When set core will disable USB3 suspend phy
+    type: boolean
+
+  snps,dis_u2_susphy_quirk:
+    description: When set core will disable USB2 suspend phy
+    type: boolean
+
+  snps,dis_enblslpm_quirk:
+    description: |
+      When set clears the enblslpm in GUSB2PHYCFG, disabling the suspend signal
+      to the PHY.
+    type: boolean
+
+  snps,dis-u1-entry-quirk:
+    description: Set if link entering into U1 needs to be disabled
+    type: boolean
+
+  snps,dis-u2-entry-quirk:
+    description: Set if link entering into U2 needs to be disabled
+    type: boolean
+
+  snps,dis_rxdet_inp3_quirk:
+    description: |
+      When set core will disable receiver detection in PHY P3 power state.
+    type: boolean
+
+  snps,dis-u2-freeclk-exists-quirk:
+    description: |
+      When set, clear the u2_freeclk_exists in GUSB2PHYCFG, specify that USB2
+      PHY doesn't provide a free-running PHY clock.
+    type: boolean
+
+  snps,dis-del-phy-power-chg-quirk:
+    description: |
+      When set core will change PHY power from P0 to P1/P2/P3 without delay.
+    type: boolean
+
+  snps,dis-tx-ipgap-linecheck-quirk:
+    description: When set, disable u2mac linestate check during HS transmit
+    type: boolean
+
+  snps,parkmode-disable-ss-quirk:
+    description: |
+      When set, all SuperSpeed bus instances in park mode are disabled.
+    type: boolean
+
+  snps,dis_metastability_quirk:
+    description: |
+      When set, disable metastability workaround. CAUTION! Use only if you are
+      absolutely sure of it.
+    type: boolean
+
+  snps,is-utmi-l1-suspend:
+    description: |
+      True when DWC3 asserts output signal utmi_l1_suspend_n, false when
+      asserts utmi_sleep_n.
+    type: boolean
+
+  snps,hird-threshold:
+    description: HIRD threshold
+    $ref: /schemas/types.yaml#/definitions/uint8
+
+  snps,hsphy_interface:
+    description: |
+      High-Speed PHY interface selection between UTMI+ and ULPI when the
+      DWC_USB3_HSPHY_INTERFACE has value 3.
+    $ref: /schemas/types.yaml#/definitions/uint8
+    enum: ["utmi", "ulpi"]
+
+  snps,quirk-frame-length-adjustment:
+    description: |
+      Value for GFLADJ_30MHZ field of GFLADJ register for post-silicon frame
+      length adjustment when the fladj_30mhz_sdbnd signal is invalid or
+      incorrect.
+    $ref: /schemas/types.yaml#/definitions/uint32
+
+  snps,rx-thr-num-pkt-prd:
+    description: |
+      Periodic ESS RX packet threshold count (host mode only). Set this and
+      snps,rx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31
+      programming guide section 1.2.4) to enable periodic ESS RX threshold.
+    $ref: /schemas/types.yaml#/definitions/uint8
+    minimum: 1
+    maximum: 16
+
+  snps,rx-max-burst-prd:
+    description: |
+      Max periodic ESS RX burst size (host mode only). Set this and
+      snps,rx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31
+      programming guide section 1.2.4) to enable periodic ESS RX threshold.
+    $ref: /schemas/types.yaml#/definitions/uint8
+    minimum: 1
+    maximum: 16
+
+  snps,tx-thr-num-pkt-prd:
+    description: |
+      Periodic ESS TX packet threshold count (host mode only). Set this and
+      snps,tx-max-burst-prd to a valid, non-zero value 1-16 (DWC_usb31
+      programming guide section 1.2.3) to enable periodic ESS TX threshold.
+    $ref: /schemas/types.yaml#/definitions/uint8
+    minimum: 1
+    maximum: 16
+
+  snps,tx-max-burst-prd:
+    description: |
+      Max periodic ESS TX burst size (host mode only). Set this and
+      snps,tx-thr-num-pkt-prd to a valid, non-zero value 1-16 (DWC_usb31
+      programming guide section 1.2.3) to enable periodic ESS TX threshold.
+    $ref: /schemas/types.yaml#/definitions/uint8
+    minimum: 1
+    maximum: 16
+
+  tx-fifo-resize:
+    description: Determines if the FIFO *has* to be reallocated
+    deprecated: true
+    type: boolean
+
+  snps,incr-burst-type-adjustment:
+    description: |
+      Value for INCR burst type of GSBUSCFG0 register, undefined length INCR
+      burst type enable and INCRx type. A single value means INCRX burst mode
+      enabled. If more than one value specified, undefined length INCR burst
+      type will be enabled with burst lengths utilized up to the maximum
+      of the values passed in this property.
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 1
+    maxItems: 8
+    uniqueItems: true
+    items:
+      enum: [1, 4, 8, 16, 32, 64, 128, 256]
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+examples:
+  - |
+    usb@4a030000 {
+      compatible = "snps,dwc3";
+      reg = <0x4a030000 0xcfff>;
+      interrupts = <0 92 4>;
+      usb-phy = <&usb2_phy>, <&usb3_phy>;
+      snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+    };
+  - |
+    usb@4a000000 {
+      compatible = "snps,dwc3";
+      reg = <0x4a000000 0xcfff>;
+      interrupts = <0 92 4>;
+      clocks = <&clk 1>, <&clk 2>, <&clk 3>;
+      clock-names = "bus_early", "ref", "suspend";
+      phys = <&usb2_phy>, <&usb3_phy>;
+      phy-names = "usb2-phy", "usb3-phy";
+      snps,dis_u2_susphy_quirk;
+      snps,dis_enblslpm_quirk;
+    };
+...