diff mbox series

[v4,02/24] dt-bindings: introduce silabs,wfx.yaml

Message ID 20201223153925.73742-3-Jerome.Pouiller@silabs.com
State Superseded
Headers show
Series wfx: get out from the staging area | expand

Commit Message

Jérôme Pouiller Dec. 23, 2020, 3:39 p.m. UTC
From: Jérôme Pouiller <jerome.pouiller@silabs.com>

Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
---
 .../bindings/net/wireless/silabs,wfx.yaml     | 133 ++++++++++++++++++
 1 file changed, 133 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml

Comments

Rob Herring Jan. 8, 2021, 2:28 a.m. UTC | #1
On Wed, Dec 23, 2020 at 04:39:03PM +0100, Jerome Pouiller wrote:
> From: Jérôme Pouiller <jerome.pouiller@silabs.com>

Commit message?

checkpatch.pl reports trailing whitespace errors.

> 
> Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
> ---
>  .../bindings/net/wireless/silabs,wfx.yaml     | 133 ++++++++++++++++++
>  1 file changed, 133 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml
> 
> diff --git a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml
> new file mode 100644
> index 000000000000..487d46c5fdc0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml
> @@ -0,0 +1,133 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +# Copyright (c) 2020, Silicon Laboratories, Inc.
> +%YAML 1.2
> +---
> +
> +$id: http://devicetree.org/schemas/net/wireless/silabs,wfx.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Silicon Labs WFxxx devicetree bindings
> +
> +maintainers:
> +  - Jérôme Pouiller <jerome.pouiller@silabs.com>
> +
> +description: >
> +  Support for the Wifi chip WFxxx from Silicon Labs. Currently, the only device
> +  from the WFxxx series is the WF200 described here:
> +     https://www.silabs.com/documents/public/data-sheets/wf200-datasheet.pdf
> +  
> +  The WF200 can be connected via SPI or via SDIO.
> +  
> +  For SDIO:
> +  
> +    Declaring the WFxxx chip in device tree is mandatory (usually, the VID/PID is
> +    sufficient for the SDIO devices).
> +  
> +    It is recommended to declare a mmc-pwrseq on SDIO host above WFx. Without
> +    it, you may encounter issues during reboot. The mmc-pwrseq should be
> +    compatible with mmc-pwrseq-simple. Please consult
> +    Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt for more
> +    information.
> +  
> +  For SPI:
> +  
> +    In add of the properties below, please consult
> +    Documentation/devicetree/bindings/spi/spi-controller.yaml for optional SPI
> +    related properties.
> +
> +properties:
> +  compatible:
> +    const: silabs,wf200
> +
> +  reg:
> +    description:
> +      When used on SDIO bus, <reg> must be set to 1. When used on SPI bus, it is
> +      the chip select address of the device as defined in the SPI devices
> +      bindings.
> +    maxItems: 1
> +
> +  spi-max-frequency: true
> +
> +  interrupts:
> +    description: The interrupt line. Triggers IRQ_TYPE_LEVEL_HIGH and
> +      IRQ_TYPE_EDGE_RISING are both supported by the chip and the driver. When
> +      SPI is used, this property is required. When SDIO is used, the "in-band"
> +      interrupt provided by the SDIO bus is used unless an interrupt is defined
> +      in the Device Tree.
> +    maxItems: 1
> +
> +  reset-gpios:
> +    description: (SPI only) Phandle of gpio that will be used to reset chip
> +      during probe. Without this property, you may encounter issues with warm
> +      boot. (For legacy purpose, the gpio in inverted when compatible ==
> +      "silabs,wfx-spi")
> +
> +      For SDIO, the reset gpio should declared using a mmc-pwrseq.
> +    maxItems: 1
> +
> +  wakeup-gpios:
> +    description: Phandle of gpio that will be used to wake-up chip. Without this
> +      property, driver will disable most of power saving features.
> +    maxItems: 1
> +
> +  silabs,antenna-config-file:
> +    $ref: /schemas/types.yaml#/definitions/string
> +    description: Use an alternative file for antenna configuration (aka
> +      "Platform Data Set" in Silabs jargon). Default is 'wf200.pds'.
> +
> +  local-mac-address: true
> +
> +  mac-address: true
> +
> +additionalProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +
> +examples:
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    spi0 {
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        wifi@0 {
> +            compatible = "silabs,wf200";
> +            pinctrl-names = "default";
> +            pinctrl-0 = <&wfx_irq &wfx_gpios>;
> +            reg = <0>;
> +            interrupts-extended = <&gpio 16 IRQ_TYPE_EDGE_RISING>;
> +            wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
> +            reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> +            spi-max-frequency = <42000000>;
> +        };
> +    };
> +
> +  - |
> +    #include <dt-bindings/gpio/gpio.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    wfx_pwrseq: wfx_pwrseq {
> +        compatible = "mmc-pwrseq-simple";
> +        pinctrl-names = "default";
> +        pinctrl-0 = <&wfx_reset>;
> +        reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> +    };
> +
> +    mmc0 {
> +        mmc-pwrseq = <&wfx_pwrseq>;
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +
> +        wifi@1 {
> +            compatible = "silabs,wf200";
> +            pinctrl-names = "default";
> +            pinctrl-0 = <&wfx_wakeup>;
> +            reg = <1>;
> +            wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
> +        };
> +    };
> +...
> -- 
> 2.29.2
>
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml
new file mode 100644
index 000000000000..487d46c5fdc0
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml
@@ -0,0 +1,133 @@ 
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020, Silicon Laboratories, Inc.
+%YAML 1.2
+---
+
+$id: http://devicetree.org/schemas/net/wireless/silabs,wfx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Silicon Labs WFxxx devicetree bindings
+
+maintainers:
+  - Jérôme Pouiller <jerome.pouiller@silabs.com>
+
+description: >
+  Support for the Wifi chip WFxxx from Silicon Labs. Currently, the only device
+  from the WFxxx series is the WF200 described here:
+     https://www.silabs.com/documents/public/data-sheets/wf200-datasheet.pdf
+  
+  The WF200 can be connected via SPI or via SDIO.
+  
+  For SDIO:
+  
+    Declaring the WFxxx chip in device tree is mandatory (usually, the VID/PID is
+    sufficient for the SDIO devices).
+  
+    It is recommended to declare a mmc-pwrseq on SDIO host above WFx. Without
+    it, you may encounter issues during reboot. The mmc-pwrseq should be
+    compatible with mmc-pwrseq-simple. Please consult
+    Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt for more
+    information.
+  
+  For SPI:
+  
+    In add of the properties below, please consult
+    Documentation/devicetree/bindings/spi/spi-controller.yaml for optional SPI
+    related properties.
+
+properties:
+  compatible:
+    const: silabs,wf200
+
+  reg:
+    description:
+      When used on SDIO bus, <reg> must be set to 1. When used on SPI bus, it is
+      the chip select address of the device as defined in the SPI devices
+      bindings.
+    maxItems: 1
+
+  spi-max-frequency: true
+
+  interrupts:
+    description: The interrupt line. Triggers IRQ_TYPE_LEVEL_HIGH and
+      IRQ_TYPE_EDGE_RISING are both supported by the chip and the driver. When
+      SPI is used, this property is required. When SDIO is used, the "in-band"
+      interrupt provided by the SDIO bus is used unless an interrupt is defined
+      in the Device Tree.
+    maxItems: 1
+
+  reset-gpios:
+    description: (SPI only) Phandle of gpio that will be used to reset chip
+      during probe. Without this property, you may encounter issues with warm
+      boot. (For legacy purpose, the gpio in inverted when compatible ==
+      "silabs,wfx-spi")
+
+      For SDIO, the reset gpio should declared using a mmc-pwrseq.
+    maxItems: 1
+
+  wakeup-gpios:
+    description: Phandle of gpio that will be used to wake-up chip. Without this
+      property, driver will disable most of power saving features.
+    maxItems: 1
+
+  silabs,antenna-config-file:
+    $ref: /schemas/types.yaml#/definitions/string
+    description: Use an alternative file for antenna configuration (aka
+      "Platform Data Set" in Silabs jargon). Default is 'wf200.pds'.
+
+  local-mac-address: true
+
+  mac-address: true
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    spi0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        wifi@0 {
+            compatible = "silabs,wf200";
+            pinctrl-names = "default";
+            pinctrl-0 = <&wfx_irq &wfx_gpios>;
+            reg = <0>;
+            interrupts-extended = <&gpio 16 IRQ_TYPE_EDGE_RISING>;
+            wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+            reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+            spi-max-frequency = <42000000>;
+        };
+    };
+
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    wfx_pwrseq: wfx_pwrseq {
+        compatible = "mmc-pwrseq-simple";
+        pinctrl-names = "default";
+        pinctrl-0 = <&wfx_reset>;
+        reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+    };
+
+    mmc0 {
+        mmc-pwrseq = <&wfx_pwrseq>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        wifi@1 {
+            compatible = "silabs,wf200";
+            pinctrl-names = "default";
+            pinctrl-0 = <&wfx_wakeup>;
+            reg = <1>;
+            wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+        };
+    };
+...