| Message ID | 20190509161109.10499-3-dmurphy@ti.com |
|---|---|
| State | Accepted |
| Commit | 4edd396a1911222da7a5d4b2bc58ab546de02bd5 |
| Headers | show |
| Series | None | expand |
On 5/9/19 6:11 PM, Dan Murphy wrote: > DT binding documentation for TI TCAN4x5x driver. > > Signed-off-by: Dan Murphy <dmurphy@ti.com> > --- > > v12 - No changes - https://lore.kernel.org/patchwork/patch/1052300/ > > v11 - No changes - https://lore.kernel.org/patchwork/patch/1051178/ > v10 - No changes - https://lore.kernel.org/patchwork/patch/1050488/ > v9 - No Changes - https://lore.kernel.org/patchwork/patch/1050118/ > v8 - No Changes - https://lore.kernel.org/patchwork/patch/1047981/ > v7 - Made device state optional - https://lore.kernel.org/patchwork/patch/1047218/ > v6 - No changes - https://lore.kernel.org/patchwork/patch/1042445/ > > .../devicetree/bindings/net/can/tcan4x5x.txt | 37 +++++++++++++++++++ > 1 file changed, 37 insertions(+) > create mode 100644 Documentation/devicetree/bindings/net/can/tcan4x5x.txt > > diff --git a/Documentation/devicetree/bindings/net/can/tcan4x5x.txt b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt > new file mode 100644 > index 000000000000..c388f7d9feb1 > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt > @@ -0,0 +1,37 @@ > +Texas Instruments TCAN4x5x CAN Controller > +================================================ > + > +This file provides device node information for the TCAN4x5x interface contains. > + > +Required properties: > + - compatible: "ti,tcan4x5x" > + - reg: 0 > + - #address-cells: 1 > + - #size-cells: 0 > + - spi-max-frequency: Maximum frequency of the SPI bus the chip can > + operate at should be less than or equal to 18 MHz. > + - data-ready-gpios: Interrupt GPIO for data and error reporting. > + - device-wake-gpios: Wake up GPIO to wake up the TCAN device. > + > +See Documentation/devicetree/bindings/net/can/m_can.txt for additional > +required property details. > + > +Optional properties: > + - reset-gpios: Hardwired output GPIO. If not defined then software > + reset. > + - device-state-gpios: Input GPIO that indicates if the device is in > + a sleep state or if the device is active. > + > +Example: > +tcan4x5x: tcan4x5x@0 { > + compatible = "ti,tcan4x5x"; > + reg = <0>; > + #address-cells = <1>; > + #size-cells = <1>; > + spi-max-frequency = <10000000>; > + bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>; > + data-ready-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; Can you convert this into a proper interrupt property? E.g.: > interrupt-parent = <&gpio4>; > interrupts = <13 0x2>; See: https://elixir.bootlin.com/linux/latest/source/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt#L21 https://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git/tree/drivers/net/can/spi/mcp251x.c?h=mcp251x#n945 > + device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; > + device-wake-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; > + reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; > +}; Marc -- Pengutronix e.K. | Marc Kleine-Budde | Industrial Linux Solutions | Phone: +49-231-2826-924 | Vertretung West/Dortmund | Fax: +49-5121-206917-5555 | Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
Marc On 8/16/19 4:38 AM, Marc Kleine-Budde wrote: > On 5/9/19 6:11 PM, Dan Murphy wrote: >> DT binding documentation for TI TCAN4x5x driver. >> >> Signed-off-by: Dan Murphy <dmurphy@ti.com> >> --- >> >> v12 - No changes - https://lore.kernel.org/patchwork/patch/1052300/ >> >> v11 - No changes - https://lore.kernel.org/patchwork/patch/1051178/ >> v10 - No changes - https://lore.kernel.org/patchwork/patch/1050488/ >> v9 - No Changes - https://lore.kernel.org/patchwork/patch/1050118/ >> v8 - No Changes - https://lore.kernel.org/patchwork/patch/1047981/ >> v7 - Made device state optional - https://lore.kernel.org/patchwork/patch/1047218/ >> v6 - No changes - https://lore.kernel.org/patchwork/patch/1042445/ >> >> .../devicetree/bindings/net/can/tcan4x5x.txt | 37 +++++++++++++++++++ >> 1 file changed, 37 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/net/can/tcan4x5x.txt >> >> diff --git a/Documentation/devicetree/bindings/net/can/tcan4x5x.txt b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt >> new file mode 100644 >> index 000000000000..c388f7d9feb1 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt >> @@ -0,0 +1,37 @@ >> +Texas Instruments TCAN4x5x CAN Controller >> +================================================ >> + >> +This file provides device node information for the TCAN4x5x interface contains. >> + >> +Required properties: >> + - compatible: "ti,tcan4x5x" >> + - reg: 0 >> + - #address-cells: 1 >> + - #size-cells: 0 >> + - spi-max-frequency: Maximum frequency of the SPI bus the chip can >> + operate at should be less than or equal to 18 MHz. >> + - data-ready-gpios: Interrupt GPIO for data and error reporting. >> + - device-wake-gpios: Wake up GPIO to wake up the TCAN device. >> + >> +See Documentation/devicetree/bindings/net/can/m_can.txt for additional >> +required property details. >> + >> +Optional properties: >> + - reset-gpios: Hardwired output GPIO. If not defined then software >> + reset. >> + - device-state-gpios: Input GPIO that indicates if the device is in >> + a sleep state or if the device is active. >> + >> +Example: >> +tcan4x5x: tcan4x5x@0 { >> + compatible = "ti,tcan4x5x"; >> + reg = <0>; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + spi-max-frequency = <10000000>; >> + bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>; >> + data-ready-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; > Can you convert this into a proper interrupt property? E.g.: OK. Do you want v13 or do you want patches on top for net-next? Dan > >> interrupt-parent = <&gpio4>; >> interrupts = <13 0x2>; > See: > https://elixir.bootlin.com/linux/latest/source/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt#L21 > https://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git/tree/drivers/net/can/spi/mcp251x.c?h=mcp251x#n945 This second link says it invalid Dan > >> + device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; >> + device-wake-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; >> + reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; >> +}; > Marc >
On 8/22/19 4:20 PM, Dan Murphy wrote: >>> +tcan4x5x: tcan4x5x@0 { >>> + compatible = "ti,tcan4x5x"; >>> + reg = <0>; >>> + #address-cells = <1>; >>> + #size-cells = <1>; >>> + spi-max-frequency = <10000000>; >>> + bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>; >>> + data-ready-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; >> Can you convert this into a proper interrupt property? E.g.: > > OK. Do you want v13 or do you want patches on top for net-next? Please use net-next/master as the base. >>> interrupt-parent = <&gpio4>; >>> interrupts = <13 0x2>; >> See: >> https://elixir.bootlin.com/linux/latest/source/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt#L21 >> https://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git/tree/drivers/net/can/spi/mcp251x.c?h=mcp251x#n945 I've removed the branch, as the patches are already upstream, have a look here: https://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git/tree/drivers/net/can/spi/mcp251x.c#n921 Marc -- Pengutronix e.K. | Marc Kleine-Budde | Industrial Linux Solutions | Phone: +49-231-2826-924 | Vertretung West/Dortmund | Fax: +49-5121-206917-5555 | Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
Marc On 8/22/19 10:46 AM, Marc Kleine-Budde wrote: > On 8/22/19 4:20 PM, Dan Murphy wrote: >>>> +tcan4x5x: tcan4x5x@0 { >>>> + compatible = "ti,tcan4x5x"; >>>> + reg = <0>; >>>> + #address-cells = <1>; >>>> + #size-cells = <1>; >>>> + spi-max-frequency = <10000000>; >>>> + bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>; >>>> + data-ready-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; >>> Can you convert this into a proper interrupt property? E.g.: >> OK. Do you want v13 or do you want patches on top for net-next? > Please use net-next/master as the base. Thanks for the reply. I see that that there are patches on top of the driver so I will send patches on top of that. Dan <snip>
diff --git a/Documentation/devicetree/bindings/net/can/tcan4x5x.txt b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt new file mode 100644 index 000000000000..c388f7d9feb1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/tcan4x5x.txt @@ -0,0 +1,37 @@ +Texas Instruments TCAN4x5x CAN Controller +================================================ + +This file provides device node information for the TCAN4x5x interface contains. + +Required properties: + - compatible: "ti,tcan4x5x" + - reg: 0 + - #address-cells: 1 + - #size-cells: 0 + - spi-max-frequency: Maximum frequency of the SPI bus the chip can + operate at should be less than or equal to 18 MHz. + - data-ready-gpios: Interrupt GPIO for data and error reporting. + - device-wake-gpios: Wake up GPIO to wake up the TCAN device. + +See Documentation/devicetree/bindings/net/can/m_can.txt for additional +required property details. + +Optional properties: + - reset-gpios: Hardwired output GPIO. If not defined then software + reset. + - device-state-gpios: Input GPIO that indicates if the device is in + a sleep state or if the device is active. + +Example: +tcan4x5x: tcan4x5x@0 { + compatible = "ti,tcan4x5x"; + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <10000000>; + bosch,mram-cfg = <0x0 0 0 32 0 0 1 1>; + data-ready-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + device-state-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; + device-wake-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>; +};
DT binding documentation for TI TCAN4x5x driver. Signed-off-by: Dan Murphy <dmurphy@ti.com> --- v12 - No changes - https://lore.kernel.org/patchwork/patch/1052300/ v11 - No changes - https://lore.kernel.org/patchwork/patch/1051178/ v10 - No changes - https://lore.kernel.org/patchwork/patch/1050488/ v9 - No Changes - https://lore.kernel.org/patchwork/patch/1050118/ v8 - No Changes - https://lore.kernel.org/patchwork/patch/1047981/ v7 - Made device state optional - https://lore.kernel.org/patchwork/patch/1047218/ v6 - No changes - https://lore.kernel.org/patchwork/patch/1042445/ .../devicetree/bindings/net/can/tcan4x5x.txt | 37 +++++++++++++++++++ 1 file changed, 37 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/can/tcan4x5x.txt -- 2.21.0.5.gaeb582a983