@@ -673,6 +673,9 @@ qca8k_setup(struct dsa_switch *ds)
/* Flush the FDB table */
qca8k_fdb_flush(priv);
+ /* We don't have interrupts for link changes, so we need to poll */
+ ds->pcs_poll = true;
+
return 0;
}
@@ -681,7 +684,7 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
const struct phylink_link_state *state)
{
struct qca8k_priv *priv = ds->priv;
- u32 reg;
+ u32 reg, val;
switch (port) {
case 0: /* 1st CPU port */
@@ -740,6 +743,34 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
case PHY_INTERFACE_MODE_1000BASEX:
/* Enable SGMII on the port */
qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
+
+ /* Enable/disable SerDes auto-negotiation as necessary */
+ val = qca8k_read(priv, QCA8K_REG_PWS);
+ if (phylink_autoneg_inband(mode))
+ val &= ~QCA8K_PWS_SERDES_AEN_DIS;
+ else
+ val |= QCA8K_PWS_SERDES_AEN_DIS;
+ qca8k_write(priv, QCA8K_REG_PWS, val);
+
+ /* Configure the SGMII parameters */
+ val = qca8k_read(priv, QCA8K_REG_SGMII_CTRL);
+
+ val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX |
+ QCA8K_SGMII_EN_TX | QCA8K_SGMII_EN_SD;
+
+ if (dsa_is_cpu_port(ds, port)) {
+ /* CPU port, we're talking to the CPU MAC, be a PHY */
+ val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
+ val |= QCA8K_SGMII_MODE_CTRL_PHY;
+ } else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
+ val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
+ val |= QCA8K_SGMII_MODE_CTRL_MAC;
+ } else if (state->interface == PHY_INTERFACE_MODE_1000BASEX) {
+ val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
+ val |= QCA8K_SGMII_MODE_CTRL_BASEX;
+ }
+
+ qca8k_write(priv, QCA8K_REG_SGMII_CTRL, val);
break;
default:
dev_err(ds->dev, "xMII mode %s not supported for port %d\n",
@@ -36,6 +36,8 @@
#define QCA8K_MAX_DELAY 3
#define QCA8K_PORT_PAD_RGMII_RX_DELAY_EN BIT(24)
#define QCA8K_PORT_PAD_SGMII_EN BIT(7)
+#define QCA8K_REG_PWS 0x010
+#define QCA8K_PWS_SERDES_AEN_DIS BIT(7)
#define QCA8K_REG_MODULE_EN 0x030
#define QCA8K_MODULE_EN_MIB BIT(0)
#define QCA8K_REG_MIB 0x034
@@ -69,6 +71,7 @@
#define QCA8K_PORT_STATUS_LINK_UP BIT(8)
#define QCA8K_PORT_STATUS_LINK_AUTO BIT(9)
#define QCA8K_PORT_STATUS_LINK_PAUSE BIT(10)
+#define QCA8K_PORT_STATUS_FLOW_AUTO BIT(12)
#define QCA8K_REG_PORT_HDR_CTRL(_i) (0x9c + (_i * 4))
#define QCA8K_PORT_HDR_CTRL_RX_MASK GENMASK(3, 2)
#define QCA8K_PORT_HDR_CTRL_RX_S 2
@@ -77,6 +80,16 @@
#define QCA8K_PORT_HDR_CTRL_ALL 2
#define QCA8K_PORT_HDR_CTRL_MGMT 1
#define QCA8K_PORT_HDR_CTRL_NONE 0
+#define QCA8K_REG_SGMII_CTRL 0x0e0
+#define QCA8K_SGMII_EN_PLL BIT(1)
+#define QCA8K_SGMII_EN_RX BIT(2)
+#define QCA8K_SGMII_EN_TX BIT(3)
+#define QCA8K_SGMII_EN_SD BIT(4)
+#define QCA8K_SGMII_CLK125M_DELAY BIT(7)
+#define QCA8K_SGMII_MODE_CTRL_MASK (BIT(22) | BIT(23))
+#define QCA8K_SGMII_MODE_CTRL_BASEX (0 << 22)
+#define QCA8K_SGMII_MODE_CTRL_PHY (1 << 22)
+#define QCA8K_SGMII_MODE_CTRL_MAC (2 << 22)
/* EEE control registers */
#define QCA8K_REG_EEE_CTRL 0x100
This patch improves the handling of the SGMII interface on the QCA8K devices. Previously the driver did no configuration of the port, even if it was selected. We now configure it up in the appropriate PHY/MAC/Base-X mode depending on what phylink tells us we are connected to and ensure it is enabled. Tested with a device where the CPU connection is RGMII (i.e. the common current use case) + one where the CPU connection is SGMII. I don't have any devices where the SGMII interface is brought out to something other than the CPU. Signed-off-by: Jonathan McDowell <noodles@earth.li> --- drivers/net/dsa/qca8k.c | 33 ++++++++++++++++++++++++++++++++- drivers/net/dsa/qca8k.h | 13 +++++++++++++ 2 files changed, 45 insertions(+), 1 deletion(-)