diff mbox series

[5/5] ARM: dts: stm32: Add DH Electronics DHCOM SoM and PDK2 board

Message ID 20200110002839.97868-5-marex@denx.de
State Superseded
Headers show
Series [1/5] ARM: stm32: Permit multiple board targets | expand

Commit Message

Marek Vasut Jan. 10, 2020, 12:28 a.m. UTC
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP157C and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.

Signed-off-by: Marek Vasut <marex at denx.de>
Cc: Patrick Delaunay <patrick.delaunay at st.com>
Cc: Patrice Chotard <patrice.chotard at st.com>
---
 arch/arm/dts/Makefile                         |   1 +
 .../arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts |   7 +
 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts       |  88 ++
 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi    | 238 ++++++
 arch/arm/dts/stm32mp157c-dhcom.dtsi           | 379 +++++++++
 arch/arm/mach-stm32mp/Kconfig                 |   1 +
 board/dhelectronics/dh_stm32mp1/Kconfig       |  25 +
 board/dhelectronics/dh_stm32mp1/MAINTAINERS   |   7 +
 board/dhelectronics/dh_stm32mp1/Makefile      |  12 +
 board/dhelectronics/dh_stm32mp1/board.c       | 777 ++++++++++++++++++
 configs/stm32mp15_dhcom_basic_defconfig       | 140 ++++
 11 files changed, 1675 insertions(+)
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
 create mode 100644 arch/arm/dts/stm32mp157c-dhcom.dtsi
 create mode 100644 board/dhelectronics/dh_stm32mp1/Kconfig
 create mode 100644 board/dhelectronics/dh_stm32mp1/MAINTAINERS
 create mode 100644 board/dhelectronics/dh_stm32mp1/Makefile
 create mode 100644 board/dhelectronics/dh_stm32mp1/board.c
 create mode 100644 configs/stm32mp15_dhcom_basic_defconfig

Comments

Patrick Delaunay Jan. 13, 2020, 2:04 p.m. UTC | #1
Hi Marek,

> From: Marek Vasut <marex at denx.de>
> Sent: vendredi 10 janvier 2020 01:29
> To: u-boot at lists.denx.de
> Cc: Marek Vasut <marex at denx.de>; Patrick DELAUNAY
> <patrick.delaunay at st.com>; Patrice CHOTARD <patrice.chotard at st.com>
> Subject: [PATCH 5/5] ARM: dts: stm32: Add DH Electronics DHCOM SoM and
> PDK2 board
> Importance: High
> 
> Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board.
> This is an SoM with STM32MP157C and an evaluation kit. The baseboard
> provides Ethernet, UART, USB, CAN and optional display.
> Signed-off-by: Marek Vasut <marex at denx.de>
> Cc: Patrick Delaunay <patrick.delaunay at st.com>
> Cc: Patrice Chotard <patrice.chotard at st.com>
> ---
>  arch/arm/dts/Makefile                         |   1 +
>  .../arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts |   7 +
>  arch/arm/dts/stm32mp157c-dhcom-pdk2.dts       |  88 ++
>  arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi    | 238 ++++++
>  arch/arm/dts/stm32mp157c-dhcom.dtsi           | 379 +++++++++
>  arch/arm/mach-stm32mp/Kconfig                 |   1 +
>  board/dhelectronics/dh_stm32mp1/Kconfig       |  25 +
>  board/dhelectronics/dh_stm32mp1/MAINTAINERS   |   7 +
>  board/dhelectronics/dh_stm32mp1/Makefile      |  12 +
>  board/dhelectronics/dh_stm32mp1/board.c       | 777 ++++++++++++++++++
>  configs/stm32mp15_dhcom_basic_defconfig       | 140 ++++
>  11 files changed, 1675 insertions(+)
>  create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
>  create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
>  create mode 100644 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
>  create mode 100644 arch/arm/dts/stm32mp157c-dhcom.dtsi
>  create mode 100644 board/dhelectronics/dh_stm32mp1/Kconfig
>  create mode 100644 board/dhelectronics/dh_stm32mp1/MAINTAINERS
>  create mode 100644 board/dhelectronics/dh_stm32mp1/Makefile
>  create mode 100644 board/dhelectronics/dh_stm32mp1/board.c
>  create mode 100644 configs/stm32mp15_dhcom_basic_defconfig
> 
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index
> 983e235f44..82489bc09c 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -859,6 +859,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
>  dtb-$(CONFIG_TARGET_STM32MP1) += \
>  	stm32mp157a-dk1.dtb \
>  	stm32mp157a-avenger96.dtb \
> +	stm32mp157c-dhcom-pdk2-u-boot.dtb \
>  	stm32mp157c-dk2.dtb \
>  	stm32mp157c-ed1.dtb \
>  	stm32mp157c-ev1.dtb
> diff --git a/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> b/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> new file mode 100644
> index 0000000000..fd99988570
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> @@ -0,0 +1,7 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2019 Marek Vasut <marex at denx.de>  */
> +
> +#include "stm32mp157c-dhcom-pdk2.dts"
> +#include "stm32mp157c-dhcom-u-boot.dtsi"
> diff --git a/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> b/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> new file mode 100644
> index 0000000000..05aa545f55
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> @@ -0,0 +1,88 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2019 Marek Vasut <marex at denx.de>  */
> +
> +#include "stm32mp157c-dhcom.dtsi"
> +
> +/ {
> +	model = "STMicroelectronics STM32MP157C DHCOM Premium
> Developer Kit (2)";
> +	compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
> +
> +	aliases {
> +		serial0 = &uart4;
> +		ethernet0 = &ethernet0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	ethernet_vio: vioregulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vio";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +};
> +
> +&ethernet0 {
> +	status = "okay";
> +	pinctrl-0 = <&ethernet0_rmii_pins_a>;
> +	pinctrl-1 = <&ethernet0_rmii_pins_sleep_a>;
> +	pinctrl-names = "default", "sleep";
> +	phy-mode = "rmii";
> +	max-speed = <100>;
> +	phy-handle = <&phy0>;
> +	st,eth_ref_clk_sel;
> +	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
> +
> +	mdio0 {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "snps,dwmac-mdio";
> +
> +		phy0: ethernet-phy at 1 {
> +			reg = <1>;
> +		};
> +	};
> +};
> +
> +&pinctrl {
> +	ethernet0_rmii_pins_a: rmii-0 {
> +		pins1 {
> +			pinmux = <STM32_PINMUX('G', 13, AF11)>, /*
> ETH1_RMII_TXD0 */
> +				 <STM32_PINMUX('G', 14, AF11)>, /*
> ETH1_RMII_TXD1 */
> +				 <STM32_PINMUX('B', 11, AF11)>, /*
> ETH1_RMII_TX_EN */
> +				 <STM32_PINMUX('A', 1, AF0)>,   /*
> ETH1_RMII_REF_CLK */
> +				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO
> */
> +				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC
> */
> +			bias-disable;
> +			drive-push-pull;
> +			slew-rate = <2>;
> +		};
> +		pins2 {
> +			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /*
> ETH1_RMII_RXD0 */
> +				 <STM32_PINMUX('C', 5, AF11)>,  /*
> ETH1_RMII_RXD1 */
> +				 <STM32_PINMUX('A', 7, AF11)>;  /*
> ETH1_RMII_CRS_DV */
> +			bias-disable;
> +		};
> +	};
> +
> +	ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
> +		pins1 {
> +			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /*
> ETH1_RMII_TXD0 */
> +				 <STM32_PINMUX('G', 14, ANALOG)>, /*
> ETH1_RMII_TXD1 */
> +				 <STM32_PINMUX('B', 11, ANALOG)>, /*
> ETH1_RMII_TX_EN */
> +				 <STM32_PINMUX('A', 2, ANALOG)>,  /*
> ETH1_MDIO */
> +				 <STM32_PINMUX('C', 1, ANALOG)>,  /*
> ETH1_MDC */
> +				 <STM32_PINMUX('C', 4, ANALOG)>,  /*
> ETH1_RMII_RXD0 */
> +				 <STM32_PINMUX('C', 5, ANALOG)>,  /*
> ETH1_RMII_RXD1 */
> +				 <STM32_PINMUX('A', 1, ANALOG)>,  /*
> ETH1_RMII_REF_CLK */
> +				 <STM32_PINMUX('A', 7, ANALOG)>;  /*
> ETH1_RMII_CRS_DV */
> +		};
> +	};
> +};
> diff --git a/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> b/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> new file mode 100644
> index 0000000000..320912edd8
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> @@ -0,0 +1,238 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2019 Marek Vasut <marex at denx.de>  */
> +
> +#include <dt-bindings/clock/stm32mp1-clksrc.h>
> +#include "stm32mp157-u-boot.dtsi"
> +#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
> +
> +/ {
> +	aliases {
> +		i2c1 = &i2c2;
> +		i2c3 = &i2c4;
> +		i2c4 = &i2c5;
> +		mmc0 = &sdmmc1;
> +		mmc1 = &sdmmc2;
> +		spi0 = &qspi;
> +		usb0 = &usbotg_hs;
> +	};
> +
> +	config {
> +		u-boot,boot-led = "heartbeat";
> +		u-boot,error-led = "error";

Excpet if I miss something, You have no led on your board (named = "heartbeat" or "error" )
This 2 line can be remove I think

> +		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> +		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	led {
> +		red {
> +			label = "error";
> +			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> +			default-state = "off";
> +			status = "okay";
> +		};
> +
> +		blue {
> +			default-state = "on";
> +		};
> +	};

This blue overridde can be remove I think.

> +};
> +
> +&i2c4 {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&i2c4_pins_a {
> +	u-boot,dm-pre-reloc;
> +	pins {
> +		u-boot,dm-pre-reloc;
> +	};
> +};
> +
> +&pmic {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&flash0 {
> +	u-boot,dm-spl;
> +};
> +
> +&qspi {
> +	u-boot,dm-spl;
> +};
> +
> +&qspi_clk_pins_a {
> +	u-boot,dm-spl;
> +	pins {
> +		u-boot,dm-spl;
> +	};
> +};
> +
> +&qspi_bk1_pins_a {
> +	u-boot,dm-spl;
> +	pins1 {
> +		u-boot,dm-spl;
> +	};
> +	pins2 {
> +		u-boot,dm-spl;
> +	};
> +};
> +
> +&qspi_bk2_pins_a {
> +	u-boot,dm-spl;
> +	pins1 {
> +		u-boot,dm-spl;
> +	};
> +	pins2 {
> +		u-boot,dm-spl;
> +	};
> +};
> +
> +&rcc {
> +	st,clksrc = <
> +		CLK_MPU_PLL1P
> +		CLK_AXI_PLL2P
> +		CLK_MCU_PLL3P
> +		CLK_PLL12_HSE
> +		CLK_PLL3_HSE
> +		CLK_PLL4_HSE
> +		CLK_RTC_LSE
> +		CLK_MCO1_DISABLED
> +		CLK_MCO2_DISABLED
> +	>;
> +
> +	st,clkdiv = <
> +		1 /*MPU*/
> +		0 /*AXI*/
> +		0 /*MCU*/
> +		1 /*APB1*/
> +		1 /*APB2*/
> +		1 /*APB3*/
> +		1 /*APB4*/
> +		2 /*APB5*/
> +		23 /*RTC*/
> +		0 /*MCO1*/
> +		0 /*MCO2*/
> +	>;
> +
> +	st,pkcs = <
> +		CLK_CKPER_HSE
> +		CLK_FMC_ACLK
> +		CLK_QSPI_ACLK
> +		CLK_ETH_PLL4P
> +		CLK_SDMMC12_PLL4P
> +		CLK_DSI_DSIPLL
> +		CLK_STGEN_HSE
> +		CLK_USBPHY_HSE
> +		CLK_SPI2S1_PLL3Q
> +		CLK_SPI2S23_PLL3Q
> +		CLK_SPI45_HSI
> +		CLK_SPI6_HSI
> +		CLK_I2C46_HSI
> +		CLK_SDMMC3_PLL4P
> +		CLK_USBO_USBPHY
> +		CLK_ADC_CKPER
> +		CLK_CEC_LSE
> +		CLK_I2C12_HSI
> +		CLK_I2C35_HSI
> +		CLK_UART1_HSI
> +		CLK_UART24_HSI
> +		CLK_UART35_HSI
> +		CLK_UART6_HSI
> +		CLK_UART78_HSI
> +		CLK_SPDIF_PLL4P
> +		CLK_FDCAN_PLL4Q
> +		CLK_SAI1_PLL3Q
> +		CLK_SAI2_PLL3Q
> +		CLK_SAI3_PLL3Q
> +		CLK_SAI4_PLL3Q
> +		CLK_RNG1_LSI
> +		CLK_RNG2_LSI
> +		CLK_LPTIM1_PCLK1
> +		CLK_LPTIM23_PCLK3
> +		CLK_LPTIM45_LSE
> +	>;
> +
> +	/* VCO = 1300.0 MHz => P = 650 (CPU) */
> +	pll1: st,pll at 0 {
> +		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
> +		frac = < 0x800 >;
> +		u-boot,dm-pre-reloc;
> +	};
> +
> +	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
> +	pll2: st,pll at 1 {
> +		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
> +		frac = < 0x1400 >;
> +		u-boot,dm-pre-reloc;
> +	};
> +
> +	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
> +	pll3: st,pll at 2 {
> +		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
> +		frac = < 0x1a04 >;
> +		u-boot,dm-pre-reloc;
> +	};
> +
> +	/* VCO = 600.0 MHz => P = 50, Q = 50, R = 50 */
> +	pll4: st,pll at 3 {
> +		cfg = < 1 49 11 11 11 PQR(1,1,1) >;
> +		u-boot,dm-pre-reloc;
> +	};
> +};
> +
> +&sdmmc1 {
> +	u-boot,dm-spl;
> +};
> +
> +&sdmmc1_b4_pins_a {
> +	u-boot,dm-spl;
> +	pins {
> +		u-boot,dm-spl;
> +	};
> +};
> +
> +&sdmmc1_dir_pins_a {
> +	u-boot,dm-spl;
> +	pins1 {
> +		u-boot,dm-spl;
> +	};
> +	pins2 {
> +		u-boot,dm-spl;
> +	};
> +};
> +
> +&sdmmc2 {
> +	u-boot,dm-spl;
> +};
> +
> +&sdmmc2_b4_pins_a {
> +	u-boot,dm-spl;
> +	pins {
> +		u-boot,dm-spl;
> +	};
> +};
> +
> +&sdmmc2_d47_pins_a {
> +	u-boot,dm-spl;
> +	pins {
> +		u-boot,dm-spl;
> +	};
> +};
> +
> +&uart4 {
> +	u-boot,dm-pre-reloc;
> +};
> +
> +&uart4_pins_a {
> +	u-boot,dm-pre-reloc;
> +	pins1 {
> +		u-boot,dm-pre-reloc;
> +	};
> +	pins2 {
> +		u-boot,dm-pre-reloc;
> +		/* pull-up on rx to avoid floating level */
> +		bias-pull-up;
> +	};
> +};
> diff --git a/arch/arm/dts/stm32mp157c-dhcom.dtsi b/arch/arm/dts/stm32mp157c-
> dhcom.dtsi
> new file mode 100644
> index 0000000000..96661ae783
> --- /dev/null
> +++ b/arch/arm/dts/stm32mp157c-dhcom.dtsi
> @@ -0,0 +1,379 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2019 Marek Vasut <marex at denx.de>  */ /dts-v1/;
> +
> +#include "stm32mp157c.dtsi"
> +#include "stm32mp157xaa-pinctrl.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/mfd/st,stpmic1.h>
> +
> +/ {
> +	memory at c0000000 {
> +		device_type = "memory";
> +		reg = <0xC0000000 0x40000000>;
> +	};
> +};
> +
> +&cec {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&cec_pins_a>;
> +	status = "okay";
> +};
> +
> +&dcmi {
> +	status = "okay";
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&dcmi_pins_a>;
> +	pinctrl-1 = <&dcmi_sleep_pins_a>;
> +};
> +
> +&dts {
> +	status = "okay";
> +};
> +
> +&i2c2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c2_pins_a>;
> +	i2c-scl-rising-time-ns = <185>;
> +	i2c-scl-falling-time-ns = <20>;
> +	status = "okay";
> +};
> +
> +&i2c4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c4_pins_a>;
> +	i2c-scl-rising-time-ns = <185>;
> +	i2c-scl-falling-time-ns = <20>;
> +	status = "okay";
> +	/* spare dmas for other usage */
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +
> +	pmic: stpmic at 33 {
> +		compatible = "st,stpmic1";
> +		reg = <0x33>;
> +		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +		status = "okay";
> +
> +		regulators {
> +			compatible = "st,stpmic1-regulators";
> +			ldo1-supply = <&v3v3>;
> +			ldo2-supply = <&v3v3>;
> +			ldo3-supply = <&vdd_ddr>;
> +			ldo5-supply = <&v3v3>;
> +			ldo6-supply = <&v3v3>;
> +			pwr_sw1-supply = <&bst_out>;
> +			pwr_sw2-supply = <&bst_out>;
> +
> +			vddcore: buck1 {
> +				regulator-name = "vddcore";
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-always-on;
> +				regulator-initial-mode = <0>;
> +				regulator-over-current-protection;
> +			};
> +
> +			vdd_ddr: buck2 {
> +				regulator-name = "vdd_ddr";
> +				regulator-min-microvolt = <1350000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-always-on;
> +				regulator-initial-mode = <0>;
> +				regulator-over-current-protection;
> +			};
> +
> +			vdd: buck3 {
> +				regulator-name = "vdd";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +				st,mask-reset;
> +				regulator-initial-mode = <0>;
> +				regulator-over-current-protection;
> +			};
> +
> +			v3v3: buck4 {
> +				regulator-name = "v3v3";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +				regulator-over-current-protection;
> +				regulator-initial-mode = <0>;
> +			};
> +
> +			vdda: ldo1 {
> +				regulator-name = "vdda";
> +				regulator-min-microvolt = <2900000>;
> +				regulator-max-microvolt = <2900000>;
> +				interrupts = <IT_CURLIM_LDO1 0>;
> +			};
> +
> +			v2v8: ldo2 {
> +				regulator-name = "v2v8";
> +				regulator-min-microvolt = <2800000>;
> +				regulator-max-microvolt = <2800000>;
> +				interrupts = <IT_CURLIM_LDO2 0>;
> +			};
> +
> +			vtt_ddr: ldo3 {
> +				regulator-name = "vtt_ddr";
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <750000>;
> +				regulator-always-on;
> +				regulator-over-current-protection;
> +			};
> +
> +			vdd_usb: ldo4 {
> +				regulator-name = "vdd_usb";
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				interrupts = <IT_CURLIM_LDO4 0>;
> +			};
> +
> +			vdd_sd: ldo5 {
> +				regulator-name = "vdd_sd";
> +				regulator-min-microvolt = <2900000>;
> +				regulator-max-microvolt = <2900000>;
> +				interrupts = <IT_CURLIM_LDO5 0>;
> +				regulator-boot-on;
> +			};
> +
> +			v1v8: ldo6 {
> +				regulator-name = "v1v8";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				interrupts = <IT_CURLIM_LDO6 0>;
> +			};
> +
> +			vref_ddr: vref_ddr {
> +				regulator-name = "vref_ddr";
> +				regulator-always-on;
> +				regulator-over-current-protection;
> +			};
> +
> +			 bst_out: boost {
> +				regulator-name = "bst_out";
> +				interrupts = <IT_OCP_BOOST 0>;
> +			 };
> +
> +			vbus_otg: pwr_sw1 {
> +				regulator-name = "vbus_otg";
> +				interrupts = <IT_OCP_OTG 0>;
> +			 };
> +
> +			 vbus_sw: pwr_sw2 {
> +				regulator-name = "vbus_sw";
> +				interrupts = <IT_OCP_SWOUT 0>;
> +				regulator-active-discharge;
> +			 };
> +		};
> +
> +		onkey {
> +			compatible = "st,stpmic1-onkey";
> +			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
> +			interrupt-names = "onkey-falling", "onkey-rising";
> +			power-off-time-sec = <10>;
> +			status = "okay";
> +		};
> +
> +		watchdog {
> +			compatible = "st,stpmic1-wdt";
> +			status = "disabled";
> +		};
> +	};
> +
> +	eeprom at 50 {
> +		compatible = "atmel,24c02";
> +		reg = <0x50>;
> +		pagesize = <16>;
> +	};
> +};
> +
> +&i2c5 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c5_pins_a>;
> +	i2c-scl-rising-time-ns = <185>;
> +	i2c-scl-falling-time-ns = <20>;
> +	status = "okay";
> +};
> +
> +&ipcc {
> +	status = "okay";
> +};
> +
> +&iwdg2 {
> +	timeout-sec = <32>;
> +	status = "okay";
> +};
> +
> +&m4_rproc {
> +	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
> +	mbox-names = "vq0", "vq1", "shutdown";
> +	status = "okay";
> +};
> +
> +&pwr {
> +	pwr-regulators {
> +		vdd-supply = <&vdd>;
> +		vdd_3v3_usbfs-supply = <&vdd_usb>;
> +	};
> +};
> +
> +&qspi {
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
> +	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a
> &qspi_bk2_sleep_pins_a>;
> +	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	status = "okay";
> +
> +	flash0: mx66l51235l at 0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +		spi-rx-bus-width = <4>;
> +		spi-max-frequency = <108000000>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +	};
> +
> +	flash1: mx66l51235l at 1 {
> +		compatible = "jedec,spi-nor";
> +		reg = <1>;
> +		spi-rx-bus-width = <4>;
> +		spi-max-frequency = <108000000>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +	};
> +};
> +
> +&rng1 {
> +	status = "okay";
> +};
> +
> +&rtc {
> +	status = "okay";
> +};
> +
> +&sdmmc1 {
> +	pinctrl-names = "default", "opendrain", "sleep";
> +	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
> +	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
> +	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
> +	broken-cd;
> +	st,sig-dir;
> +	st,neg-edge;
> +	st,use-ckin;
> +	bus-width = <4>;
> +	vmmc-supply = <&vdd_sd>;
> +	status = "okay";
> +};
> +
> +&sdmmc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> +	non-removable;
> +	no-sd;
> +	no-sdio;
> +	st,sig-dir;
> +	st,neg-edge;
> +	bus-width = <8>;
> +	vmmc-supply = <&v3v3>;
> +	status = "okay";
> +};
> +
> +&spi1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi1_pins_a>;
> +	status = "disabled";
> +};
> +
> +&timers2 {
> +	/* spare dmas for other usage (un-delete to enable pwm capture) */
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +	status = "disabled";
> +	pwm {
> +		pinctrl-0 = <&pwm2_pins_a>;
> +		pinctrl-names = "default";
> +		status = "okay";
> +	};
> +	timer at 1 {
> +		status = "okay";
> +	};
> +};
> +
> +&timers6 {
> +	status = "okay";
> +	/* spare dmas for other usage */
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +	timer at 5 {
> +		status = "okay";
> +	};
> +};
> +
> +&timers8 {
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +	status = "disabled";
> +	pwm {
> +		pinctrl-0 = <&pwm8_pins_a>;
> +		pinctrl-names = "default";
> +		status = "okay";
> +	};
> +	timer at 7 {
> +		status = "okay";
> +	};
> +};
> +
> +&timers12 {
> +	/delete-property/dmas;
> +	/delete-property/dma-names;
> +	status = "disabled";
> +	pwm {
> +		pinctrl-0 = <&pwm12_pins_a>;
> +		pinctrl-names = "default";
> +		status = "okay";
> +	};
> +	timer at 11 {
> +		status = "okay";
> +	};
> +};
> +
> +&uart4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart4_pins_a>;
> +	status = "okay";
> +};
> +
> +&usbh_ehci {
> +	phys = <&usbphyc_port0>;
> +	phy-names = "usb";
> +	status = "okay";
> +};
> +
> +&usbotg_hs {
> +	dr_mode = "peripheral";
> +	phys = <&usbphyc_port1 0>;
> +	phy-names = "usb2-phy";
> +	vbus-supply = <&vbus_otg>;
> +	status = "okay";
> +};
> +
> +&usbphyc {
> +	status = "okay";
> +};
> +
> +&usbphyc_port0 {
> +	phy-supply = <&vdd_usb>;
> +};
> +
> +&usbphyc_port1 {
> +	phy-supply = <&vdd_usb>;
> +};
> diff --git a/arch/arm/mach-stm32mp/Kconfig b/arch/arm/mach-stm32mp/Kconfig
> index ae28f6e206..1aa5f8a122 100644
> --- a/arch/arm/mach-stm32mp/Kconfig
> +++ b/arch/arm/mach-stm32mp/Kconfig
> @@ -147,5 +147,6 @@ config DEBUG_UART_CLOCK  endif
> 
>  source "board/st/stm32mp1/Kconfig"
> +source "board/dhelectronics/dh_stm32mp1/Kconfig"
> 
>  endif
> diff --git a/board/dhelectronics/dh_stm32mp1/Kconfig
> b/board/dhelectronics/dh_stm32mp1/Kconfig
> new file mode 100644
> index 0000000000..e751a3e5ed
> --- /dev/null
> +++ b/board/dhelectronics/dh_stm32mp1/Kconfig
> @@ -0,0 +1,25 @@
> +config TARGET_DH_STM32MP1_PDK2
> +	bool "support of DH STM32MP1 PDK2"
> +	default y

Avoid set default y here.... 
to avoid to activate this config for ST board.

In fact it should be a choice between the 2 targets
- TARGET_DH_STM32MP1_PDK2
- TARGET_ST_STM32MP1

> +
> +if TARGET_DH_STM32MP1_PDK2
> +
> +config SYS_BOARD
> +	default "dh_stm32mp1"
> +
> +config SYS_VENDOR
> +	default "dhelectronics"
> +
> +config SYS_CONFIG_NAME
> +	default "stm32mp1"
> +
> +config ENV_SECT_SIZE
> +	default 0x10000 if ENV_IS_IN_SPI_FLASH
> +
> +config ENV_OFFSET
> +	default 0x1E0000 if ENV_IS_IN_SPI_FLASH
> +
> +config ENV_OFFSET_REDUND
> +	default 0x1F0000 if ENV_IS_IN_SPI_FLASH
> +
> +endif
> diff --git a/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> new file mode 100644
> index 0000000000..38f54a3da4
> --- /dev/null
> +++ b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> @@ -0,0 +1,7 @@
> +DH_STM32MP1_PDK2 BOARD
> +M:	Marek Vasut <marex at denx.de>
> +S:	Maintained
> +F:	arch/arm/dts/stm32mp157c-dhcom*
> +F:	board/dhelectronics/dh_stm32mp1/
> +F:	configs/stm32mp15_dhcom_basic_defconfig
> +F:	include/configs/stm32mp1.h
> diff --git a/board/dhelectronics/dh_stm32mp1/Makefile
> b/board/dhelectronics/dh_stm32mp1/Makefile
> new file mode 100644
> index 0000000000..a9d28218ef
> --- /dev/null
> +++ b/board/dhelectronics/dh_stm32mp1/Makefile
> @@ -0,0 +1,12 @@
> +# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause # # Copyright (C)
> +2018, STMicroelectronics - All Rights Reserved #
> +
> +ifdef CONFIG_SPL_BUILD
> +obj-y += ../../st/stm32mp1/spl.o
> +else
> +obj-$(CONFIG_CMD_STBOARD) += ../../st/stm32mp1/cmd_stboard.o endif
> +

I don't think you wee to support the command STMicroelctronics board (ref MBxxxx). 
it is only a internal command for ST : save/read board id in OTP.

> +obj-y += ../../st/stm32mp1/board.o board.o
> diff --git a/board/dhelectronics/dh_stm32mp1/board.c
> b/board/dhelectronics/dh_stm32mp1/board.c
> new file mode 100644
> index 0000000000..54cc3b7587
> --- /dev/null
> +++ b/board/dhelectronics/dh_stm32mp1/board.c
> @@ -0,0 +1,777 @@
> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> +/*
> + * Copyright (C) 2018, STMicroelectronics - All Rights Reserved  */
> +
> +#include <common.h>
> +#include <adc.h>
> +#include <asm/arch/stm32.h>
> +#include <asm/arch/sys_proto.h>
> +#include <asm/gpio.h>
> +#include <asm/io.h>
> +#include <bootm.h>
> +#include <clk.h>
> +#include <config.h>
> +#include <dm.h>
> +#include <dm/device.h>
> +#include <dm/uclass.h>
> +#include <env.h>
> +#include <env_internal.h>
> +#include <g_dnl.h>
> +#include <generic-phy.h>
> +#include <i2c.h>
> +#include <i2c_eeprom.h>
> +#include <init.h>
> +#include <led.h>
> +#include <memalign.h>
> +#include <misc.h>
> +#include <mtd.h>
> +#include <mtd_node.h>
> +#include <netdev.h>
> +#include <phy.h>
> +#include <power/regulator.h>
> +#include <remoteproc.h>
> +#include <reset.h>
> +#include <syscon.h>
> +#include <usb.h>
> +#include <usb/dwc2_udc.h>
> +#include <watchdog.h>
> +
> +/* SYSCFG registers */
> +#define SYSCFG_BOOTR		0x00
> +#define SYSCFG_PMCSETR		0x04
> +#define SYSCFG_IOCTRLSETR	0x18
> +#define SYSCFG_ICNR		0x1C
> +#define SYSCFG_CMPCR		0x20
> +#define SYSCFG_CMPENSETR	0x24
> +#define SYSCFG_PMCCLRR		0x44
> +
> +#define SYSCFG_BOOTR_BOOT_MASK		GENMASK(2, 0)
> +#define SYSCFG_BOOTR_BOOTPD_SHIFT	4
> +
> +#define SYSCFG_IOCTRLSETR_HSLVEN_TRACE		BIT(0)
> +#define SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI	BIT(1)
> +#define SYSCFG_IOCTRLSETR_HSLVEN_ETH		BIT(2)
> +#define SYSCFG_IOCTRLSETR_HSLVEN_SDMMC		BIT(3)
> +#define SYSCFG_IOCTRLSETR_HSLVEN_SPI		BIT(4)
> +
> +#define SYSCFG_CMPCR_SW_CTRL		BIT(1)
> +#define SYSCFG_CMPCR_READY		BIT(8)
> +
> +#define SYSCFG_CMPENSETR_MPU_EN		BIT(0)
> +
> +#define SYSCFG_PMCSETR_ETH_CLK_SEL	BIT(16)
> +#define SYSCFG_PMCSETR_ETH_REF_CLK_SEL	BIT(17)
> +
> +#define SYSCFG_PMCSETR_ETH_SELMII	BIT(20)
> +
> +#define SYSCFG_PMCSETR_ETH_SEL_MASK	GENMASK(23, 21)
> +#define SYSCFG_PMCSETR_ETH_SEL_GMII_MII	0
> +#define SYSCFG_PMCSETR_ETH_SEL_RGMII	BIT(21)
> +#define SYSCFG_PMCSETR_ETH_SEL_RMII	BIT(23)
> +
> +/*
> + * Get a global data pointer
> + */
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int setup_mac_address(void)
> +{
> +	struct udevice *dev;
> +	ofnode eeprom;
> +	unsigned char enetaddr[6];
> +	int ret;
> +
> +	ret = eth_env_get_enetaddr("ethaddr", enetaddr);
> +	if (ret)	/* ethaddr is already set */
> +		return 0;
> +
> +	eeprom = ofnode_path("/soc/i2c at 5c002000/eeprom at 50");
> +	if (!ofnode_valid(eeprom)) {
> +		printf("Invalid hardware path to EEPROM!\n");
> +		return -ENODEV;
> +	}
> +
> +	ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom,
> &dev);
> +	if (ret) {
> +		printf("Cannot find EEPROM!\n");
> +		return ret;
> +	}
> +
> +	ret = i2c_eeprom_read(dev, 0xfa, enetaddr, 0x6);
> +	if (ret) {
> +		printf("Error reading configuration EEPROM!\n");
> +		return ret;
> +	}
> +
> +	if (is_valid_ethaddr(enetaddr))
> +		eth_env_set_enetaddr("ethaddr", enetaddr);
> +
> +	return 0;
> +}
> +
> +int checkboard(void)
> +{
> +	int ret;
> +	char *mode;
> +	u32 otp;
> +	struct udevice *dev;
> +	const char *fdt_compat;
> +	int fdt_compat_len;
> +
> +	if (IS_ENABLED(CONFIG_STM32MP1_OPTEE))
> +		mode = "trusted with OP-TEE";
> +	else if (IS_ENABLED(CONFIG_STM32MP1_TRUSTED))
> +		mode = "trusted";
> +	else
> +		mode = "basic";
> +
> +	printf("Board: stm32mp1 in %s mode", mode);
> +	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
> +				 &fdt_compat_len);
> +	if (fdt_compat && fdt_compat_len)
> +		printf(" (%s)", fdt_compat);
> +	puts("\n");
> +
> +	ret = uclass_get_device_by_driver(UCLASS_MISC,
> +					  DM_GET_DRIVER(stm32mp_bsec),
> +					  &dev);
> +
> +	if (!ret)
> +		ret = misc_read(dev,
> STM32_BSEC_SHADOW(BSEC_OTP_BOARD),
> +				&otp, sizeof(otp));
> +	if (ret > 0 && otp) {
> +		printf("Board: MB%04x Var%d Rev.%c-%02d\n",
> +		       otp >> 16,
> +		       (otp >> 12) & 0xF,
> +		       ((otp >> 8) & 0xF) - 1 + 'A',
> +		       otp & 0xF);
> +	}

This part (read OTP / / display MBxxx ) can be dropped for your board (it is a ST specific part).

> +	return 0;
> +}
> +
> +static void board_key_check(void)
> +{
> +#if defined(CONFIG_FASTBOOT) || defined(CONFIG_CMD_STM32PROG)
> +	ofnode node;
> +	struct gpio_desc gpio;
> +	enum forced_boot_mode boot_mode = BOOT_NORMAL;
> +
> +	node = ofnode_path("/config");
> +	if (!ofnode_valid(node)) {
> +		debug("%s: no /config node?\n", __func__);
> +		return;
> +	}
> +#ifdef CONFIG_FASTBOOT
> +	if (gpio_request_by_name_nodev(node, "st,fastboot-gpios", 0,
> +				       &gpio, GPIOD_IS_IN)) {
> +		debug("%s: could not find a /config/st,fastboot-gpios\n",
> +		      __func__);
> +	} else {
> +		if (dm_gpio_get_value(&gpio)) {
> +			puts("Fastboot key pressed, ");
> +			boot_mode = BOOT_FASTBOOT;
> +		}
> +
> +		dm_gpio_free(NULL, &gpio);
> +	}
> +#endif
> +#ifdef CONFIG_CMD_STM32PROG
> +	if (gpio_request_by_name_nodev(node, "st,stm32prog-gpios", 0,
> +				       &gpio, GPIOD_IS_IN)) {
> +		debug("%s: could not find a /config/st,stm32prog-gpios\n",
> +		      __func__);
> +	} else {
> +		if (dm_gpio_get_value(&gpio)) {
> +			puts("STM32Programmer key pressed, ");
> +			boot_mode = BOOT_STM32PROG;
> +		}
> +		dm_gpio_free(NULL, &gpio);
> +	}
> +#endif
> +
> +	if (boot_mode != BOOT_NORMAL) {
> +		puts("entering download mode...\n");
> +		clrsetbits_le32(TAMP_BOOT_CONTEXT,
> +				TAMP_BOOT_FORCED_MASK,
> +				boot_mode);
> +	}
> +#endif
> +}

Do you support GPIO key press on  GPAIOA14 / 15 (as it is done in ST boards EV1 : DK1 / DK2)
If no all this function can be dropped.

> +#if defined(CONFIG_USB_GADGET) &&
> defined(CONFIG_USB_GADGET_DWC2_OTG)
> +
> +/* STMicroelectronics STUSB1600 Type-C controller */
> +#define STUSB1600_CC_CONNECTION_STATUS		0x0E
> +
> +/* STUSB1600_CC_CONNECTION_STATUS bitfields */
> +#define STUSB1600_CC_ATTACH			BIT(0)
> +
> +static int stusb1600_init(struct udevice **dev_stusb1600) {
> +	ofnode node;
> +	struct udevice *dev, *bus;
> +	int ret;
> +	u32 chip_addr;
> +
> +	*dev_stusb1600 = NULL;
> +
> +	/* if node stusb1600 is present, means DK1 or DK2 board */
> +	node = ofnode_by_compatible(ofnode_null(), "st,stusb1600");
> +	if (!ofnode_valid(node))
> +		return -ENODEV;
> +
> +	ret = ofnode_read_u32(node, "reg", &chip_addr);
> +	if (ret)
> +		return -EINVAL;
> +
> +	ret = uclass_get_device_by_ofnode(UCLASS_I2C,
> ofnode_get_parent(node),
> +					  &bus);
> +	if (ret) {
> +		printf("bus for stusb1600 not found\n");
> +		return -ENODEV;
> +	}
> +
> +	ret = dm_i2c_probe(bus, chip_addr, 0, &dev);
> +	if (!ret)
> +		*dev_stusb1600 = dev;
> +
> +	return ret;
> +}
> +
> +static int stusb1600_cable_connected(struct udevice *dev) {
> +	u8 status;
> +
> +	if (dm_i2c_read(dev, STUSB1600_CC_CONNECTION_STATUS, &status,
> 1))
> +		return 0;
> +
> +	return status & STUSB1600_CC_ATTACH;
> +}
> +
> +#include <usb/dwc2_udc.h>
> +int g_dnl_board_usb_cable_connected(void)
> +{
> +	struct udevice *stusb1600;
> +	struct udevice *dwc2_udc_otg;
> +	int ret;
> +
> +	if (!stusb1600_init(&stusb1600))
> +		return stusb1600_cable_connected(stusb1600);
> +
> +	ret = uclass_get_device_by_driver(UCLASS_USB_GADGET_GENERIC,
> +					  DM_GET_DRIVER(dwc2_udc_otg),
> +					  &dwc2_udc_otg);
> +	if (!ret)
> +		debug("dwc2_udc_otg init failed\n");
> +
> +	return dwc2_udc_B_session_valid(dwc2_udc_otg);
> +}
> +

If you don't have STUSB1600 (external usb typeC controller)
All this part can dropped.

> +#define STM32MP1_G_DNL_DFU_PRODUCT_NUM 0xdf11 #define
> +STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM 0x0afb
> +
> +int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char
> +*name) {
> +	if (!strcmp(name, "usb_dnl_dfu"))
> +		put_unaligned(STM32MP1_G_DNL_DFU_PRODUCT_NUM, &dev-
> >idProduct);
> +	else if (!strcmp(name, "usb_dnl_fastboot"))
> +
> 	put_unaligned(STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM,
> +			      &dev->idProduct);
> +	else
> +		put_unaligned(CONFIG_USB_GADGET_PRODUCT_NUM, &dev-
> >idProduct);
> +
> +	return 0;
> +}
> +
> +#endif /* CONFIG_USB_GADGET */
> +
> +#ifdef CONFIG_LED
> +static int get_led(struct udevice **dev, char *led_string) {
> +	char *led_name;
> +	int ret;
> +
> +	led_name = fdtdec_get_config_string(gd->fdt_blob, led_string);
> +	if (!led_name) {
> +		pr_debug("%s: could not find %s config string\n",
> +			 __func__, led_string);
> +		return -ENOENT;
> +	}
> +	ret = led_get_by_label(led_name, dev);
> +	if (ret) {
> +		debug("%s: get=%d\n", __func__, ret);
> +		return ret;
> +	}
> +
> +	return 0;
> +}
> +
> +static int setup_led(enum led_state_t cmd) {
> +	struct udevice *dev;
> +	int ret;
> +
> +	ret = get_led(&dev, "u-boot,boot-led");
> +	if (ret)
> +		return ret;
> +
> +	ret = led_set_state(dev, cmd);
> +	return ret;
> +}
> +#endif
> +
> +static void __maybe_unused led_error_blink(u32 nb_blink) { #ifdef
> +CONFIG_LED
> +	int ret;
> +	struct udevice *led;
> +	u32 i;
> +#endif
> +
> +	if (!nb_blink)
> +		return;
> +
> +#ifdef CONFIG_LED
> +	ret = get_led(&led, "u-boot,error-led");
> +	if (!ret) {
> +		/* make u-boot,error-led blinking */
> +		/* if U32_MAX and 125ms interval, for 17.02 years */
> +		for (i = 0; i < 2 * nb_blink; i++) {
> +			led_set_state(led, LEDST_TOGGLE);
> +			mdelay(125);
> +			WATCHDOG_RESET();
> +		}
> +	}
> +#endif
> +
> +	/* infinite: the boot process must be stopped */
> +	if (nb_blink == U32_MAX)
> +		hang();
> +}
> +
> +static void sysconf_init(void)
> +{
> +#ifndef CONFIG_STM32MP1_TRUSTED
> +	u8 *syscfg;
> +#ifdef CONFIG_DM_REGULATOR
> +	struct udevice *pwr_dev;
> +	struct udevice *pwr_reg;
> +	struct udevice *dev;
> +	int ret;
> +	u32 otp = 0;
> +#endif
> +	u32 bootr;
> +
> +	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
> +
> +	/* interconnect update : select master using the port 1 */
> +	/* LTDC = AXI_M9 */
> +	/* GPU  = AXI_M8 */
> +	/* today information is hardcoded in U-Boot */
> +	writel(BIT(9), syscfg + SYSCFG_ICNR);
> +
> +	/* disable Pull-Down for boot pin connected to VDD */
> +	bootr = readl(syscfg + SYSCFG_BOOTR);
> +	bootr &= ~(SYSCFG_BOOTR_BOOT_MASK <<
> SYSCFG_BOOTR_BOOTPD_SHIFT);
> +	bootr |= (bootr & SYSCFG_BOOTR_BOOT_MASK) <<
> SYSCFG_BOOTR_BOOTPD_SHIFT;
> +	writel(bootr, syscfg + SYSCFG_BOOTR);
> +
> +#ifdef CONFIG_DM_REGULATOR
> +	/* High Speed Low Voltage Pad mode Enable for SPI, SDMMC, ETH,
> QSPI
> +	 * and TRACE. Needed above ~50MHz and conditioned by AFMUX
> selection.
> +	 * The customer will have to disable this for low frequencies
> +	 * or if AFMUX is selected but the function not used, typically for
> +	 * TRACE. Otherwise, impact on power consumption.
> +	 *
> +	 * WARNING:
> +	 *   enabling High Speed mode while VDD>2.7V
> +	 *   with the OTP product_below_2v5 (OTP 18, BIT 13)
> +	 *   erroneously set to 1 can damage the IC!
> +	 *   => U-Boot set the register only if VDD < 2.7V (in DT)
> +	 *      but this value need to be consistent with board design
> +	 */
> +	ret = uclass_get_device_by_driver(UCLASS_PMIC,
> +					  DM_GET_DRIVER(stm32mp_pwr_pmic),
> +					  &pwr_dev);
> +	if (!ret) {
> +		ret = uclass_get_device_by_driver(UCLASS_MISC,
> +
> DM_GET_DRIVER(stm32mp_bsec),
> +						  &dev);
> +		if (ret) {
> +			pr_err("Can't find stm32mp_bsec driver\n");
> +			return;
> +		}
> +
> +		ret = misc_read(dev, STM32_BSEC_SHADOW(18), &otp, 4);
> +		if (ret > 0)
> +			otp = otp & BIT(13);
> +
> +		/* get VDD = vdd-supply */
> +		ret = device_get_supply_regulator(pwr_dev, "vdd-supply",
> +						  &pwr_reg);
> +
> +		/* check if VDD is Low Voltage */
> +		if (!ret) {
> +			if (regulator_get_value(pwr_reg) < 2700000) {
> +				writel(SYSCFG_IOCTRLSETR_HSLVEN_TRACE |
> +				       SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI
> |
> +				       SYSCFG_IOCTRLSETR_HSLVEN_ETH |
> +				       SYSCFG_IOCTRLSETR_HSLVEN_SDMMC |
> +				       SYSCFG_IOCTRLSETR_HSLVEN_SPI,
> +				       syscfg + SYSCFG_IOCTRLSETR);
> +
> +				if (!otp)
> +					pr_err("product_below_2v5=0: HSLVEN
> protected by HW\n");
> +			} else {
> +				if (otp)
> +					pr_err("product_below_2v5=1: HSLVEN
> update is destructive, no update as VDD>2.7V\n");
> +			}
> +		} else {
> +			debug("VDD unknown");
> +		}
> +	}
> +#endif
> +
> +	/* activate automatic I/O compensation
> +	 * warning: need to ensure CSI enabled and ready in clock driver
> +	 */
> +	writel(SYSCFG_CMPENSETR_MPU_EN, syscfg +
> SYSCFG_CMPENSETR);
> +
> +	while (!(readl(syscfg + SYSCFG_CMPCR) & SYSCFG_CMPCR_READY))
> +		;
> +	clrbits_le32(syscfg + SYSCFG_CMPCR, SYSCFG_CMPCR_SW_CTRL);
> #endif }
> +
> +/* board dependent setup after realloc */ int board_init(void) {
> +	struct udevice *dev;
> +
> +	/* address of boot parameters */
> +	gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;
> +
> +	/* probe all PINCTRL for hog */
> +	for (uclass_first_device(UCLASS_PINCTRL, &dev);
> +	     dev;
> +	     uclass_next_device(&dev)) {
> +		pr_debug("probe pincontrol = %s\n", dev->name);
> +	}
> +
> +	board_key_check();
> +
> +#ifdef CONFIG_DM_REGULATOR
> +	regulators_enable_boot_on(_DEBUG);
> +#endif
> +
> +	sysconf_init();
> +
> +	if (CONFIG_IS_ENABLED(CONFIG_LED))
> +		led_default_state();
> +
> +	return 0;
> +}
> +
> +int board_late_init(void)
> +{
> +	char *boot_device;
> +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> +	const void *fdt_compat;
> +	int fdt_compat_len;
> +	int ret;
> +	u32 otp;
> +	struct udevice *dev;
> +	char buf[10];
> +
> +	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
> +				 &fdt_compat_len);
> +	if (fdt_compat && fdt_compat_len) {
> +		if (strncmp(fdt_compat, "st,", 3) != 0)
> +			env_set("board_name", fdt_compat);
> +		else
> +			env_set("board_name", fdt_compat + 3);
> +	}
> +	ret = uclass_get_device_by_driver(UCLASS_MISC,
> +					  DM_GET_DRIVER(stm32mp_bsec),
> +					  &dev);
> +
> +	if (!ret)
> +		ret = misc_read(dev,
> STM32_BSEC_SHADOW(BSEC_OTP_BOARD),
> +				&otp, sizeof(otp));
> +	if (!ret && otp) {
> +		snprintf(buf, sizeof(buf), "0x%04x", otp >> 16);
> +		env_set("board_id", buf);
> +
> +		snprintf(buf, sizeof(buf), "0x%04x",
> +			 ((otp >> 8) & 0xF) - 1 + 0xA);
> +		env_set("board_rev", buf);
> +	}
> +#endif
> +
> +	/* Check the boot-source to disable bootdelay */
> +	boot_device = env_get("boot_device");
> +	if (!strcmp(boot_device, "serial") || !strcmp(boot_device, "usb"))
> +		env_set("bootdelay", "0");
> +
> +	return 0;
> +}
> +
> +void board_quiesce_devices(void)
> +{
> +#ifdef CONFIG_LED
> +	setup_led(LEDST_OFF);
> +#endif
> +}
> +
> +/* eth init function : weak called in eqos driver */ int
> +board_interface_eth_init(struct udevice *dev,
> +			     phy_interface_t interface_type) {
> +	u8 *syscfg;
> +	u32 value;
> +	bool eth_clk_sel_reg = false;
> +	bool eth_ref_clk_sel_reg = false;
> +
> +	/* Gigabit Ethernet 125MHz clock selection. */
> +	eth_clk_sel_reg = dev_read_bool(dev, "st,eth_clk_sel");
> +
> +	/* Ethernet 50Mhz RMII clock selection */
> +	eth_ref_clk_sel_reg =
> +		dev_read_bool(dev, "st,eth_ref_clk_sel");
> +
> +	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
> +
> +	if (!syscfg)
> +		return -ENODEV;
> +
> +	switch (interface_type) {
> +	case PHY_INTERFACE_MODE_MII:
> +		value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
> +			SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
> +		debug("%s: PHY_INTERFACE_MODE_MII\n", __func__);
> +		break;
> +	case PHY_INTERFACE_MODE_GMII:
> +		if (eth_clk_sel_reg)
> +			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
> +				SYSCFG_PMCSETR_ETH_CLK_SEL;
> +		else
> +			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII;
> +		debug("%s: PHY_INTERFACE_MODE_GMII\n", __func__);
> +		break;
> +	case PHY_INTERFACE_MODE_RMII:
> +		if (eth_ref_clk_sel_reg)
> +			value = SYSCFG_PMCSETR_ETH_SEL_RMII |
> +				SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
> +		else
> +			value = SYSCFG_PMCSETR_ETH_SEL_RMII;
> +		debug("%s: PHY_INTERFACE_MODE_RMII\n", __func__);
> +		break;
> +	case PHY_INTERFACE_MODE_RGMII:
> +	case PHY_INTERFACE_MODE_RGMII_ID:
> +	case PHY_INTERFACE_MODE_RGMII_RXID:
> +	case PHY_INTERFACE_MODE_RGMII_TXID:
> +		if (eth_clk_sel_reg)
> +			value = SYSCFG_PMCSETR_ETH_SEL_RGMII |
> +				SYSCFG_PMCSETR_ETH_CLK_SEL;
> +		else
> +			value = SYSCFG_PMCSETR_ETH_SEL_RGMII;
> +		debug("%s: PHY_INTERFACE_MODE_RGMII\n", __func__);
> +		break;
> +	default:
> +		debug("%s: Do not manage %d interface\n",
> +		      __func__, interface_type);
> +		/* Do not manage others interfaces */
> +		return -EINVAL;
> +	}
> +
> +	/* clear and set ETH configuration bits */
> +	writel(SYSCFG_PMCSETR_ETH_SEL_MASK |
> SYSCFG_PMCSETR_ETH_SELMII |
> +	       SYSCFG_PMCSETR_ETH_REF_CLK_SEL |
> SYSCFG_PMCSETR_ETH_CLK_SEL,
> +	       syscfg + SYSCFG_PMCCLRR);
> +	writel(value, syscfg + SYSCFG_PMCSETR);
> +
> +	return 0;
> +}
> +
> +enum env_location env_get_location(enum env_operation op, int prio) {
> +	if (prio)
> +		return ENVL_UNKNOWN;
> +
> +#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
> +	return ENVL_SPI_FLASH;
> +#else
> +	return ENVL_NOWHERE;
> +#endif
> +}
> +
> +#ifdef CONFIG_SYS_MTDPARTS_RUNTIME
> +
> +#define MTDPARTS_LEN		256
> +#define MTDIDS_LEN		128
> +
> +/**
> + * The mtdparts_nand0 and mtdparts_nor0 variable tends to be long.
> + * If we need to access it before the env is relocated, then we need
> + * to use our own stack buffer. gd->env_buf will be too small.
> + *
> + * @param buf temporary buffer pointer MTDPARTS_LEN long
> + * @return mtdparts variable string, NULL if not found  */ static const
> +char *env_get_mtdparts(const char *str, char *buf) {
> +	if (gd->flags & GD_FLG_ENV_READY)
> +		return env_get(str);
> +	if (env_get_f(str, buf, MTDPARTS_LEN) != -1)
> +		return buf;
> +
> +	return NULL;
> +}
> +
> +/**
> + * update the variables "mtdids" and "mtdparts" with content of
> +mtdparts_<dev>  */ static void board_get_mtdparts(const char *dev,
> +			       char *mtdids,
> +			       char *mtdparts)
> +{
> +	char env_name[32] = "mtdparts_";
> +	char tmp_mtdparts[MTDPARTS_LEN];
> +	const char *tmp;
> +
> +	/* name of env variable to read = mtdparts_<dev> */
> +	strcat(env_name, dev);
> +	tmp = env_get_mtdparts(env_name, tmp_mtdparts);
> +	if (tmp) {
> +		/* mtdids: "<dev>=<dev>, ...." */
> +		if (mtdids[0] != '\0')
> +			strcat(mtdids, ",");
> +		strcat(mtdids, dev);
> +		strcat(mtdids, "=");
> +		strcat(mtdids, dev);
> +
> +		/* mtdparts: "mtdparts=<dev>:<mtdparts_<dev>>;..." */
> +		if (mtdparts[0] != '\0')
> +			strncat(mtdparts, ";", MTDPARTS_LEN);
> +		else
> +			strcat(mtdparts, "mtdparts=");
> +		strncat(mtdparts, dev, MTDPARTS_LEN);
> +		strncat(mtdparts, ":", MTDPARTS_LEN);
> +		strncat(mtdparts, tmp, MTDPARTS_LEN);
> +	}
> +}
> +
> +void board_mtdparts_default(const char **mtdids, const char **mtdparts)
> +{
> +	struct udevice *dev;
> +	static char parts[3 * MTDPARTS_LEN + 1];
> +	static char ids[MTDIDS_LEN + 1];
> +	static bool mtd_initialized;
> +
> +	if (mtd_initialized) {
> +		*mtdids = ids;
> +		*mtdparts = parts;
> +		return;
> +	}
> +
> +	memset(parts, 0, sizeof(parts));
> +	memset(ids, 0, sizeof(ids));
> +
> +	/* probe all MTD devices */
> +	for (uclass_first_device(UCLASS_MTD, &dev);
> +	     dev;
> +	     uclass_next_device(&dev)) {
> +		pr_debug("mtd device = %s\n", dev->name);
> +	}
> +
> +	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
> +		board_get_mtdparts("nor0", ids, parts);
> +
> +	mtd_initialized = true;
> +	*mtdids = ids;
> +	*mtdparts = parts;
> +	debug("%s:mtdids=%s & mtdparts=%s\n", __func__, ids, parts); } #endif
> +
> +#if defined(CONFIG_OF_BOARD_SETUP)
> +int ft_board_setup(void *blob, bd_t *bd) {
> +	return 0;
> +}
> +#endif
> +
> +#ifdef CONFIG_SET_DFU_ALT_INFO
> +#define DFU_ALT_BUF_LEN SZ_1K
> +
> +static void board_get_alt_info(const char *dev, char *buff) {
> +	char var_name[32] = "dfu_alt_info_";
> +	int ret;
> +
> +	ALLOC_CACHE_ALIGN_BUFFER(char, tmp_alt, DFU_ALT_BUF_LEN);
> +
> +	/* name of env variable to read = dfu_alt_info_<dev> */
> +	strcat(var_name, dev);
> +	ret = env_get_f(var_name, tmp_alt, DFU_ALT_BUF_LEN);
> +	if (ret) {
> +		if (buff[0] != '\0')
> +			strcat(buff, "&");
> +		strncat(buff, tmp_alt, DFU_ALT_BUF_LEN);
> +	}
> +}
> +
> +void set_dfu_alt_info(char *interface, char *devstr) {
> +	struct udevice *dev;
> +
> +	ALLOC_CACHE_ALIGN_BUFFER(char, buf, DFU_ALT_BUF_LEN);
> +
> +	if (env_get("dfu_alt_info"))
> +		return;
> +
> +	memset(buf, 0, sizeof(buf));
> +
> +	/* probe all MTD devices */
> +	mtd_probe_devices();
> +
> +	board_get_alt_info("ram", buf);
> +
> +	if (!uclass_get_device(UCLASS_MMC, 0, &dev))
> +		board_get_alt_info("mmc0", buf);
> +
> +	if (!uclass_get_device(UCLASS_MMC, 1, &dev))
> +		board_get_alt_info("mmc1", buf);
> +
> +	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
> +		board_get_alt_info("nor0", buf);
> +
> +	env_set("dfu_alt_info", buf);
> +	puts("DFU alt info setting: done\n");
> +}
> +#endif
> +
> +static void board_copro_image_process(ulong fw_image, size_t fw_size) {
> +	int ret, id = 0; /* Copro id fixed to 0 as only one coproc on mp1 */
> +
> +	if (!rproc_is_initialized())
> +		if (rproc_init()) {
> +			printf("Remote Processor %d initialization failed\n",
> +			       id);
> +			return;
> +		}
> +
> +	ret = rproc_load(id, fw_image, fw_size);
> +	printf("Load Remote Processor %d with data at addr=0x%08lx %u
> bytes:%s\n",
> +	       id, fw_image, fw_size, ret ? " Failed!" : " Success!");
> +
> +	if (!ret) {
> +		rproc_start(id);
> +		env_set("copro_state", "booted");
> +	}
> +}
> +
> +U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_COPRO,
> board_copro_image_process);
> diff --git a/configs/stm32mp15_dhcom_basic_defconfig
> b/configs/stm32mp15_dhcom_basic_defconfig
> new file mode 100644
> index 0000000000..e4f331a913
> --- /dev/null
> +++ b/configs/stm32mp15_dhcom_basic_defconfig
> @@ -0,0 +1,140 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_STM32MP=y
> +CONFIG_SYS_MALLOC_F_LEN=0x3000
> +CONFIG_SPL_MMC_SUPPORT=y
> +CONFIG_ENV_SIZE=0x4000
> +CONFIG_SPL=y
> +CONFIG_TARGET_STM32MP1=y
> +# CONFIG_TARGET_STM32MP157C_DK2 is not set

CONFIG_TARGET_DH_STM32MP1_PDK2=y

> +CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y #
> +CONFIG_ARMV7_VIRT is not set
> +CONFIG_SPL_TEXT_BASE=0x2FFC2500
> +CONFIG_DISTRO_DEFAULTS=y
> +CONFIG_FIT=y
> +# CONFIG_BOOTSTAGE is not set
> +CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
> +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
> +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
> +CONFIG_SPL_I2C_SUPPORT=y
> +CONFIG_SPL_MTD_SUPPORT=y
> +CONFIG_SPL_POWER_SUPPORT=y
> +CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
> +CONFIG_SYS_PROMPT="STM32MP> "
> +# CONFIG_CMD_BOOTD is not set
> +# CONFIG_CMD_ELF is not set
> +# CONFIG_CMD_IMI is not set
> +# CONFIG_CMD_XIMG is not set
> +# CONFIG_CMD_EXPORTENV is not set
> +CONFIG_CMD_EEPROM=y
> +CONFIG_CMD_MEMINFO=y
> +CONFIG_CMD_MEMTEST=y
> +CONFIG_CMD_ADC=y
> +CONFIG_CMD_CLK=y
> +CONFIG_CMD_DFU=y
> +CONFIG_CMD_FUSE=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_GPT=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_MTD=y
> +CONFIG_CMD_REMOTEPROC=y
> +CONFIG_CMD_SPI=y
> +CONFIG_CMD_USB=y
> +CONFIG_CMD_USB_MASS_STORAGE=y
> +CONFIG_CMD_BMP=y
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_TIMER=y
> +CONFIG_CMD_PMIC=y
> +CONFIG_CMD_REGULATOR=y
> +CONFIG_CMD_EXT4_WRITE=y
> +CONFIG_CMD_MTDPARTS=y
> +# CONFIG_SPL_DOS_PARTITION is not set
> +CONFIG_DEFAULT_DEVICE_TREE="stm32mp157c-dhcom-pdk2-u-boot"
> +CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-
> extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names
> assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
> +CONFIG_ENV_IS_IN_SPI_FLASH=y
> +CONFIG_USE_ENV_SPI_BUS=y
> +CONFIG_ENV_SPI_BUS=0
> +CONFIG_USE_ENV_SPI_CS=y
> +CONFIG_ENV_SPI_CS=0
> +CONFIG_USE_ENV_SPI_MAX_HZ=y
> +CONFIG_ENV_SPI_MAX_HZ=10000000
> +CONFIG_USE_ENV_SPI_MODE=y
> +CONFIG_ENV_SPI_MODE=0x0
> +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
> +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> +CONFIG_NET_RANDOM_ETHADDR=y
> +CONFIG_IP_DEFRAG=y
> +CONFIG_TFTP_BLOCKSIZE=1536
> +CONFIG_STM32_ADC=y
> +CONFIG_SPL_BLOCK_CACHE=y
> +CONFIG_DFU_MMC=y
> +CONFIG_DFU_RAM=y
> +CONFIG_DFU_VIRT=y
> +CONFIG_DM_HWSPINLOCK=y
> +CONFIG_HWSPINLOCK_STM32=y
> +CONFIG_DM_I2C=y
> +CONFIG_SYS_I2C_STM32F7=y
> +CONFIG_LED=y
> +CONFIG_LED_GPIO=y
> +CONFIG_DM_MAILBOX=y
> +CONFIG_STM32_IPCC=y
> +CONFIG_I2C_EEPROM=y
> +CONFIG_DM_MMC=y
> +CONFIG_SUPPORT_EMMC_BOOT=y
> +CONFIG_STM32_SDMMC2=y
> +CONFIG_MTD=y
> +CONFIG_DM_SPI_FLASH=y
> +CONFIG_SPI_FLASH_MACRONIX=y
> +CONFIG_SPI_FLASH_SPANSION=y
> +CONFIG_SPI_FLASH_STMICRO=y
> +CONFIG_SPI_FLASH_WINBOND=y
> +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
> CONFIG_SPI_FLASH_MTD=y
> +CONFIG_SPL_SPI_FLASH_MTD=y CONFIG_DM_ETH=y
> CONFIG_DWC_ETH_QOS=y
> +CONFIG_PHY=y CONFIG_PHY_STM32_USBPHYC=y CONFIG_PINCONF=y #
> +CONFIG_SPL_PINCTRL_FULL is not set CONFIG_PINCTRL_STMFX=y
> +CONFIG_DM_PMIC=y # CONFIG_SPL_PMIC_CHILDREN is not set
> +CONFIG_PMIC_STPMIC1=y CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_REGULATOR_GPIO=y
> CONFIG_DM_REGULATOR_STM32_VREFBUF=y
> +CONFIG_DM_REGULATOR_STPMIC1=y
> +CONFIG_REMOTEPROC_STM32_COPRO=y
> +CONFIG_DM_RTC=y
> +CONFIG_RTC_STM32=y
> +CONFIG_SERIAL_RX_BUFFER=y
> +CONFIG_SPI=y
> +CONFIG_DM_SPI=y
> +CONFIG_STM32_QSPI=y
> +CONFIG_STM32_SPI=y
> +CONFIG_USB=y
> +CONFIG_DM_USB=y
> +CONFIG_DM_USB_GADGET=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_GENERIC=y
> +CONFIG_USB_GADGET=y
> +CONFIG_USB_GADGET_MANUFACTURER="dh"
> +CONFIG_USB_GADGET_VENDOR_NUM=0x0483
> +CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
> +CONFIG_USB_GADGET_DWC2_OTG=y
> +CONFIG_USB_GADGET_DOWNLOAD=y
> +CONFIG_USB_HOST_ETHER=y
> +CONFIG_USB_ETHER_ASIX=y
> +CONFIG_DM_VIDEO=y
> +CONFIG_BACKLIGHT_GPIO=y
> +CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
> +CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
> +CONFIG_VIDEO_STM32=y
> +CONFIG_VIDEO_STM32_DSI=y
> +CONFIG_VIDEO_STM32_MAX_XRES=1280
> +CONFIG_VIDEO_STM32_MAX_YRES=800
> +CONFIG_LZO=y
> +CONFIG_FDT_FIXUP_PARTITIONS=y
> --
> 2.24.1
> 

Regards

Patrick
Patrick Delaunay Jan. 17, 2020, 4:32 p.m. UTC | #2
Hi Marek,

> From: Patrick DELAUNAY
> Sent: lundi 13 janvier 2020 15:05
> 
> Hi Marek,
> 
> > From: Marek Vasut <marex at denx.de>
> > Sent: vendredi 10 janvier 2020 01:29
> >
> > Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board.
> > This is an SoM with STM32MP157C and an evaluation kit. The baseboard
> > provides Ethernet, UART, USB, CAN and optional display.
> > Signed-off-by: Marek Vasut <marex at denx.de>
> > Cc: Patrick Delaunay <patrick.delaunay at st.com>
> > Cc: Patrice Chotard <patrice.chotard at st.com>
> > ---

For information, I merge the serie, except this patch 5/5 on master brach and I sent a pull request for u-boot-stm32-20200117.

For this patch, I propose a rebase and also many modification liked to my previous remark
(I remove ST only parts for stboard command, and also led and key management) .

This proposal is present in the branch https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/next
	https://gitlab.denx.de/u-boot/custodians/u-boot-stm/commit/db48e11b1eccf23f3f9ba26e886a798e74df6a01

your initial patch is in applied https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/dh
	

Can you test the "next" branch and check the difference with your initial patch ( applied in dh branch
https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/dh 
=> https://gitlab.denx.de/u-boot/custodians/u-boot-stm/commit/0ab3ce72f82b946ac0924dfcdc082792f325eb68 )

I hope that I don't remove something really present on the SOM.

If you are OK, can you send a V2 version with the "next" branch content and I will integrate it in master branch for next pull request.

Thanks, 

Patrick


> >  arch/arm/dts/Makefile                         |   1 +
> >  .../arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts |   7 +
> >  arch/arm/dts/stm32mp157c-dhcom-pdk2.dts       |  88 ++
> >  arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi    | 238 ++++++
> >  arch/arm/dts/stm32mp157c-dhcom.dtsi           | 379 +++++++++
> >  arch/arm/mach-stm32mp/Kconfig                 |   1 +
> >  board/dhelectronics/dh_stm32mp1/Kconfig       |  25 +
> >  board/dhelectronics/dh_stm32mp1/MAINTAINERS   |   7 +
> >  board/dhelectronics/dh_stm32mp1/Makefile      |  12 +
> >  board/dhelectronics/dh_stm32mp1/board.c       | 777 ++++++++++++++++++
> >  configs/stm32mp15_dhcom_basic_defconfig       | 140 ++++
> >  11 files changed, 1675 insertions(+)
> >  create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> >  create mode 100644 arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> >  create mode 100644 arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> >  create mode 100644 arch/arm/dts/stm32mp157c-dhcom.dtsi
> >  create mode 100644 board/dhelectronics/dh_stm32mp1/Kconfig
> >  create mode 100644 board/dhelectronics/dh_stm32mp1/MAINTAINERS
> >  create mode 100644 board/dhelectronics/dh_stm32mp1/Makefile
> >  create mode 100644 board/dhelectronics/dh_stm32mp1/board.c
> >  create mode 100644 configs/stm32mp15_dhcom_basic_defconfig
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index
> > 983e235f44..82489bc09c 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -859,6 +859,7 @@ dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
> >  dtb-$(CONFIG_TARGET_STM32MP1) += \
> >  	stm32mp157a-dk1.dtb \
> >  	stm32mp157a-avenger96.dtb \
> > +	stm32mp157c-dhcom-pdk2-u-boot.dtb \
> >  	stm32mp157c-dk2.dtb \
> >  	stm32mp157c-ed1.dtb \
> >  	stm32mp157c-ev1.dtb
> > diff --git a/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> > b/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> > new file mode 100644
> > index 0000000000..fd99988570
> > --- /dev/null
> > +++ b/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
> > @@ -0,0 +1,7 @@
> > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> > +/*
> > + * Copyright (C) 2019 Marek Vasut <marex at denx.de>  */
> > +
> > +#include "stm32mp157c-dhcom-pdk2.dts"
> > +#include "stm32mp157c-dhcom-u-boot.dtsi"
> > diff --git a/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> > b/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> > new file mode 100644
> > index 0000000000..05aa545f55
> > --- /dev/null
> > +++ b/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
> > @@ -0,0 +1,88 @@
> > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> > +/*
> > + * Copyright (C) 2019 Marek Vasut <marex at denx.de>  */
> > +
> > +#include "stm32mp157c-dhcom.dtsi"
> > +
> > +/ {
> > +	model = "STMicroelectronics STM32MP157C DHCOM Premium
> > Developer Kit (2)";
> > +	compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
> > +
> > +	aliases {
> > +		serial0 = &uart4;
> > +		ethernet0 = &ethernet0;
> > +	};
> > +
> > +	chosen {
> > +		stdout-path = "serial0:115200n8";
> > +	};
> > +
> > +	ethernet_vio: vioregulator {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "vio";
> > +		regulator-min-microvolt = <3300000>;
> > +		regulator-max-microvolt = <3300000>;
> > +		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
> > +		regulator-always-on;
> > +		regulator-boot-on;
> > +	};
> > +};
> > +
> > +&ethernet0 {
> > +	status = "okay";
> > +	pinctrl-0 = <&ethernet0_rmii_pins_a>;
> > +	pinctrl-1 = <&ethernet0_rmii_pins_sleep_a>;
> > +	pinctrl-names = "default", "sleep";
> > +	phy-mode = "rmii";
> > +	max-speed = <100>;
> > +	phy-handle = <&phy0>;
> > +	st,eth_ref_clk_sel;
> > +	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
> > +
> > +	mdio0 {
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		compatible = "snps,dwmac-mdio";
> > +
> > +		phy0: ethernet-phy at 1 {
> > +			reg = <1>;
> > +		};
> > +	};
> > +};
> > +
> > +&pinctrl {
> > +	ethernet0_rmii_pins_a: rmii-0 {
> > +		pins1 {
> > +			pinmux = <STM32_PINMUX('G', 13, AF11)>, /*
> > ETH1_RMII_TXD0 */
> > +				 <STM32_PINMUX('G', 14, AF11)>, /*
> > ETH1_RMII_TXD1 */
> > +				 <STM32_PINMUX('B', 11, AF11)>, /*
> > ETH1_RMII_TX_EN */
> > +				 <STM32_PINMUX('A', 1, AF0)>,   /*
> > ETH1_RMII_REF_CLK */
> > +				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO
> > */
> > +				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC
> > */
> > +			bias-disable;
> > +			drive-push-pull;
> > +			slew-rate = <2>;
> > +		};
> > +		pins2 {
> > +			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /*
> > ETH1_RMII_RXD0 */
> > +				 <STM32_PINMUX('C', 5, AF11)>,  /*
> > ETH1_RMII_RXD1 */
> > +				 <STM32_PINMUX('A', 7, AF11)>;  /*
> > ETH1_RMII_CRS_DV */
> > +			bias-disable;
> > +		};
> > +	};
> > +
> > +	ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
> > +		pins1 {
> > +			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /*
> > ETH1_RMII_TXD0 */
> > +				 <STM32_PINMUX('G', 14, ANALOG)>, /*
> > ETH1_RMII_TXD1 */
> > +				 <STM32_PINMUX('B', 11, ANALOG)>, /*
> > ETH1_RMII_TX_EN */
> > +				 <STM32_PINMUX('A', 2, ANALOG)>,  /*
> > ETH1_MDIO */
> > +				 <STM32_PINMUX('C', 1, ANALOG)>,  /*
> > ETH1_MDC */
> > +				 <STM32_PINMUX('C', 4, ANALOG)>,  /*
> > ETH1_RMII_RXD0 */
> > +				 <STM32_PINMUX('C', 5, ANALOG)>,  /*
> > ETH1_RMII_RXD1 */
> > +				 <STM32_PINMUX('A', 1, ANALOG)>,  /*
> > ETH1_RMII_REF_CLK */
> > +				 <STM32_PINMUX('A', 7, ANALOG)>;  /*
> > ETH1_RMII_CRS_DV */
> > +		};
> > +	};
> > +};
> > diff --git a/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> > b/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> > new file mode 100644
> > index 0000000000..320912edd8
> > --- /dev/null
> > +++ b/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
> > @@ -0,0 +1,238 @@
> > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> > +/*
> > + * Copyright (C) 2019 Marek Vasut <marex at denx.de>  */
> > +
> > +#include <dt-bindings/clock/stm32mp1-clksrc.h>
> > +#include "stm32mp157-u-boot.dtsi"
> > +#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
> > +
> > +/ {
> > +	aliases {
> > +		i2c1 = &i2c2;
> > +		i2c3 = &i2c4;
> > +		i2c4 = &i2c5;
> > +		mmc0 = &sdmmc1;
> > +		mmc1 = &sdmmc2;
> > +		spi0 = &qspi;
> > +		usb0 = &usbotg_hs;
> > +	};
> > +
> > +	config {
> > +		u-boot,boot-led = "heartbeat";
> > +		u-boot,error-led = "error";
> 
> Excpet if I miss something, You have no led on your board (named = "heartbeat"
> or "error" ) This 2 line can be remove I think
> 
> > +		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> > +		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
> > +	};
> > +
> > +	led {
> > +		red {
> > +			label = "error";
> > +			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
> > +			default-state = "off";
> > +			status = "okay";
> > +		};
> > +
> > +		blue {
> > +			default-state = "on";
> > +		};
> > +	};
> 
> This blue overridde can be remove I think.
> 
> > +};
> > +
> > +&i2c4 {
> > +	u-boot,dm-pre-reloc;
> > +};
> > +
> > +&i2c4_pins_a {
> > +	u-boot,dm-pre-reloc;
> > +	pins {
> > +		u-boot,dm-pre-reloc;
> > +	};
> > +};
> > +
> > +&pmic {
> > +	u-boot,dm-pre-reloc;
> > +};
> > +
> > +&flash0 {
> > +	u-boot,dm-spl;
> > +};
> > +
> > +&qspi {
> > +	u-boot,dm-spl;
> > +};
> > +
> > +&qspi_clk_pins_a {
> > +	u-boot,dm-spl;
> > +	pins {
> > +		u-boot,dm-spl;
> > +	};
> > +};
> > +
> > +&qspi_bk1_pins_a {
> > +	u-boot,dm-spl;
> > +	pins1 {
> > +		u-boot,dm-spl;
> > +	};
> > +	pins2 {
> > +		u-boot,dm-spl;
> > +	};
> > +};
> > +
> > +&qspi_bk2_pins_a {
> > +	u-boot,dm-spl;
> > +	pins1 {
> > +		u-boot,dm-spl;
> > +	};
> > +	pins2 {
> > +		u-boot,dm-spl;
> > +	};
> > +};
> > +
> > +&rcc {
> > +	st,clksrc = <
> > +		CLK_MPU_PLL1P
> > +		CLK_AXI_PLL2P
> > +		CLK_MCU_PLL3P
> > +		CLK_PLL12_HSE
> > +		CLK_PLL3_HSE
> > +		CLK_PLL4_HSE
> > +		CLK_RTC_LSE
> > +		CLK_MCO1_DISABLED
> > +		CLK_MCO2_DISABLED
> > +	>;
> > +
> > +	st,clkdiv = <
> > +		1 /*MPU*/
> > +		0 /*AXI*/
> > +		0 /*MCU*/
> > +		1 /*APB1*/
> > +		1 /*APB2*/
> > +		1 /*APB3*/
> > +		1 /*APB4*/
> > +		2 /*APB5*/
> > +		23 /*RTC*/
> > +		0 /*MCO1*/
> > +		0 /*MCO2*/
> > +	>;
> > +
> > +	st,pkcs = <
> > +		CLK_CKPER_HSE
> > +		CLK_FMC_ACLK
> > +		CLK_QSPI_ACLK
> > +		CLK_ETH_PLL4P
> > +		CLK_SDMMC12_PLL4P
> > +		CLK_DSI_DSIPLL
> > +		CLK_STGEN_HSE
> > +		CLK_USBPHY_HSE
> > +		CLK_SPI2S1_PLL3Q
> > +		CLK_SPI2S23_PLL3Q
> > +		CLK_SPI45_HSI
> > +		CLK_SPI6_HSI
> > +		CLK_I2C46_HSI
> > +		CLK_SDMMC3_PLL4P
> > +		CLK_USBO_USBPHY
> > +		CLK_ADC_CKPER
> > +		CLK_CEC_LSE
> > +		CLK_I2C12_HSI
> > +		CLK_I2C35_HSI
> > +		CLK_UART1_HSI
> > +		CLK_UART24_HSI
> > +		CLK_UART35_HSI
> > +		CLK_UART6_HSI
> > +		CLK_UART78_HSI
> > +		CLK_SPDIF_PLL4P
> > +		CLK_FDCAN_PLL4Q
> > +		CLK_SAI1_PLL3Q
> > +		CLK_SAI2_PLL3Q
> > +		CLK_SAI3_PLL3Q
> > +		CLK_SAI4_PLL3Q
> > +		CLK_RNG1_LSI
> > +		CLK_RNG2_LSI
> > +		CLK_LPTIM1_PCLK1
> > +		CLK_LPTIM23_PCLK3
> > +		CLK_LPTIM45_LSE
> > +	>;
> > +
> > +	/* VCO = 1300.0 MHz => P = 650 (CPU) */
> > +	pll1: st,pll at 0 {
> > +		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
> > +		frac = < 0x800 >;
> > +		u-boot,dm-pre-reloc;
> > +	};
> > +
> > +	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
> > +	pll2: st,pll at 1 {
> > +		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
> > +		frac = < 0x1400 >;
> > +		u-boot,dm-pre-reloc;
> > +	};
> > +
> > +	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
> > +	pll3: st,pll at 2 {
> > +		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
> > +		frac = < 0x1a04 >;
> > +		u-boot,dm-pre-reloc;
> > +	};
> > +
> > +	/* VCO = 600.0 MHz => P = 50, Q = 50, R = 50 */
> > +	pll4: st,pll at 3 {
> > +		cfg = < 1 49 11 11 11 PQR(1,1,1) >;
> > +		u-boot,dm-pre-reloc;
> > +	};
> > +};
> > +
> > +&sdmmc1 {
> > +	u-boot,dm-spl;
> > +};
> > +
> > +&sdmmc1_b4_pins_a {
> > +	u-boot,dm-spl;
> > +	pins {
> > +		u-boot,dm-spl;
> > +	};
> > +};
> > +
> > +&sdmmc1_dir_pins_a {
> > +	u-boot,dm-spl;
> > +	pins1 {
> > +		u-boot,dm-spl;
> > +	};
> > +	pins2 {
> > +		u-boot,dm-spl;
> > +	};
> > +};
> > +
> > +&sdmmc2 {
> > +	u-boot,dm-spl;
> > +};
> > +
> > +&sdmmc2_b4_pins_a {
> > +	u-boot,dm-spl;
> > +	pins {
> > +		u-boot,dm-spl;
> > +	};
> > +};
> > +
> > +&sdmmc2_d47_pins_a {
> > +	u-boot,dm-spl;
> > +	pins {
> > +		u-boot,dm-spl;
> > +	};
> > +};
> > +
> > +&uart4 {
> > +	u-boot,dm-pre-reloc;
> > +};
> > +
> > +&uart4_pins_a {
> > +	u-boot,dm-pre-reloc;
> > +	pins1 {
> > +		u-boot,dm-pre-reloc;
> > +	};
> > +	pins2 {
> > +		u-boot,dm-pre-reloc;
> > +		/* pull-up on rx to avoid floating level */
> > +		bias-pull-up;
> > +	};
> > +};
> > diff --git a/arch/arm/dts/stm32mp157c-dhcom.dtsi
> > b/arch/arm/dts/stm32mp157c- dhcom.dtsi new file mode 100644 index
> > 0000000000..96661ae783
> > --- /dev/null
> > +++ b/arch/arm/dts/stm32mp157c-dhcom.dtsi
> > @@ -0,0 +1,379 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> > +/*
> > + * Copyright (C) 2019 Marek Vasut <marex at denx.de>  */ /dts-v1/;
> > +
> > +#include "stm32mp157c.dtsi"
> > +#include "stm32mp157xaa-pinctrl.dtsi"
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/mfd/st,stpmic1.h>
> > +
> > +/ {
> > +	memory at c0000000 {
> > +		device_type = "memory";
> > +		reg = <0xC0000000 0x40000000>;
> > +	};
> > +};
> > +
> > +&cec {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&cec_pins_a>;
> > +	status = "okay";
> > +};
> > +
> > +&dcmi {
> > +	status = "okay";
> > +	pinctrl-names = "default", "sleep";
> > +	pinctrl-0 = <&dcmi_pins_a>;
> > +	pinctrl-1 = <&dcmi_sleep_pins_a>;
> > +};
> > +
> > +&dts {
> > +	status = "okay";
> > +};
> > +
> > +&i2c2 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&i2c2_pins_a>;
> > +	i2c-scl-rising-time-ns = <185>;
> > +	i2c-scl-falling-time-ns = <20>;
> > +	status = "okay";
> > +};
> > +
> > +&i2c4 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&i2c4_pins_a>;
> > +	i2c-scl-rising-time-ns = <185>;
> > +	i2c-scl-falling-time-ns = <20>;
> > +	status = "okay";
> > +	/* spare dmas for other usage */
> > +	/delete-property/dmas;
> > +	/delete-property/dma-names;
> > +
> > +	pmic: stpmic at 33 {
> > +		compatible = "st,stpmic1";
> > +		reg = <0x33>;
> > +		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> > +		interrupt-controller;
> > +		#interrupt-cells = <2>;
> > +		status = "okay";
> > +
> > +		regulators {
> > +			compatible = "st,stpmic1-regulators";
> > +			ldo1-supply = <&v3v3>;
> > +			ldo2-supply = <&v3v3>;
> > +			ldo3-supply = <&vdd_ddr>;
> > +			ldo5-supply = <&v3v3>;
> > +			ldo6-supply = <&v3v3>;
> > +			pwr_sw1-supply = <&bst_out>;
> > +			pwr_sw2-supply = <&bst_out>;
> > +
> > +			vddcore: buck1 {
> > +				regulator-name = "vddcore";
> > +				regulator-min-microvolt = <800000>;
> > +				regulator-max-microvolt = <1350000>;
> > +				regulator-always-on;
> > +				regulator-initial-mode = <0>;
> > +				regulator-over-current-protection;
> > +			};
> > +
> > +			vdd_ddr: buck2 {
> > +				regulator-name = "vdd_ddr";
> > +				regulator-min-microvolt = <1350000>;
> > +				regulator-max-microvolt = <1350000>;
> > +				regulator-always-on;
> > +				regulator-initial-mode = <0>;
> > +				regulator-over-current-protection;
> > +			};
> > +
> > +			vdd: buck3 {
> > +				regulator-name = "vdd";
> > +				regulator-min-microvolt = <3300000>;
> > +				regulator-max-microvolt = <3300000>;
> > +				regulator-always-on;
> > +				st,mask-reset;
> > +				regulator-initial-mode = <0>;
> > +				regulator-over-current-protection;
> > +			};
> > +
> > +			v3v3: buck4 {
> > +				regulator-name = "v3v3";
> > +				regulator-min-microvolt = <3300000>;
> > +				regulator-max-microvolt = <3300000>;
> > +				regulator-always-on;
> > +				regulator-over-current-protection;
> > +				regulator-initial-mode = <0>;
> > +			};
> > +
> > +			vdda: ldo1 {
> > +				regulator-name = "vdda";
> > +				regulator-min-microvolt = <2900000>;
> > +				regulator-max-microvolt = <2900000>;
> > +				interrupts = <IT_CURLIM_LDO1 0>;
> > +			};
> > +
> > +			v2v8: ldo2 {
> > +				regulator-name = "v2v8";
> > +				regulator-min-microvolt = <2800000>;
> > +				regulator-max-microvolt = <2800000>;
> > +				interrupts = <IT_CURLIM_LDO2 0>;
> > +			};
> > +
> > +			vtt_ddr: ldo3 {
> > +				regulator-name = "vtt_ddr";
> > +				regulator-min-microvolt = <500000>;
> > +				regulator-max-microvolt = <750000>;
> > +				regulator-always-on;
> > +				regulator-over-current-protection;
> > +			};
> > +
> > +			vdd_usb: ldo4 {
> > +				regulator-name = "vdd_usb";
> > +				regulator-min-microvolt = <3300000>;
> > +				regulator-max-microvolt = <3300000>;
> > +				interrupts = <IT_CURLIM_LDO4 0>;
> > +			};
> > +
> > +			vdd_sd: ldo5 {
> > +				regulator-name = "vdd_sd";
> > +				regulator-min-microvolt = <2900000>;
> > +				regulator-max-microvolt = <2900000>;
> > +				interrupts = <IT_CURLIM_LDO5 0>;
> > +				regulator-boot-on;
> > +			};
> > +
> > +			v1v8: ldo6 {
> > +				regulator-name = "v1v8";
> > +				regulator-min-microvolt = <1800000>;
> > +				regulator-max-microvolt = <1800000>;
> > +				interrupts = <IT_CURLIM_LDO6 0>;
> > +			};
> > +
> > +			vref_ddr: vref_ddr {
> > +				regulator-name = "vref_ddr";
> > +				regulator-always-on;
> > +				regulator-over-current-protection;
> > +			};
> > +
> > +			 bst_out: boost {
> > +				regulator-name = "bst_out";
> > +				interrupts = <IT_OCP_BOOST 0>;
> > +			 };
> > +
> > +			vbus_otg: pwr_sw1 {
> > +				regulator-name = "vbus_otg";
> > +				interrupts = <IT_OCP_OTG 0>;
> > +			 };
> > +
> > +			 vbus_sw: pwr_sw2 {
> > +				regulator-name = "vbus_sw";
> > +				interrupts = <IT_OCP_SWOUT 0>;
> > +				regulator-active-discharge;
> > +			 };
> > +		};
> > +
> > +		onkey {
> > +			compatible = "st,stpmic1-onkey";
> > +			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
> > +			interrupt-names = "onkey-falling", "onkey-rising";
> > +			power-off-time-sec = <10>;
> > +			status = "okay";
> > +		};
> > +
> > +		watchdog {
> > +			compatible = "st,stpmic1-wdt";
> > +			status = "disabled";
> > +		};
> > +	};
> > +
> > +	eeprom at 50 {
> > +		compatible = "atmel,24c02";
> > +		reg = <0x50>;
> > +		pagesize = <16>;
> > +	};
> > +};
> > +
> > +&i2c5 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&i2c5_pins_a>;
> > +	i2c-scl-rising-time-ns = <185>;
> > +	i2c-scl-falling-time-ns = <20>;
> > +	status = "okay";
> > +};
> > +
> > +&ipcc {
> > +	status = "okay";
> > +};
> > +
> > +&iwdg2 {
> > +	timeout-sec = <32>;
> > +	status = "okay";
> > +};
> > +
> > +&m4_rproc {
> > +	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
> > +	mbox-names = "vq0", "vq1", "shutdown";
> > +	status = "okay";
> > +};
> > +
> > +&pwr {
> > +	pwr-regulators {
> > +		vdd-supply = <&vdd>;
> > +		vdd_3v3_usbfs-supply = <&vdd_usb>;
> > +	};
> > +};
> > +
> > +&qspi {
> > +	pinctrl-names = "default", "sleep";
> > +	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
> > +	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a
> > &qspi_bk2_sleep_pins_a>;
> > +	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
> > +	#address-cells = <1>;
> > +	#size-cells = <0>;
> > +	status = "okay";
> > +
> > +	flash0: mx66l51235l at 0 {
> > +		compatible = "jedec,spi-nor";
> > +		reg = <0>;
> > +		spi-rx-bus-width = <4>;
> > +		spi-max-frequency = <108000000>;
> > +		#address-cells = <1>;
> > +		#size-cells = <1>;
> > +	};
> > +
> > +	flash1: mx66l51235l at 1 {
> > +		compatible = "jedec,spi-nor";
> > +		reg = <1>;
> > +		spi-rx-bus-width = <4>;
> > +		spi-max-frequency = <108000000>;
> > +		#address-cells = <1>;
> > +		#size-cells = <1>;
> > +	};
> > +};
> > +
> > +&rng1 {
> > +	status = "okay";
> > +};
> > +
> > +&rtc {
> > +	status = "okay";
> > +};
> > +
> > +&sdmmc1 {
> > +	pinctrl-names = "default", "opendrain", "sleep";
> > +	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
> > +	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
> > +	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
> > +	broken-cd;
> > +	st,sig-dir;
> > +	st,neg-edge;
> > +	st,use-ckin;
> > +	bus-width = <4>;
> > +	vmmc-supply = <&vdd_sd>;
> > +	status = "okay";
> > +};
> > +
> > +&sdmmc2 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> > +	non-removable;
> > +	no-sd;
> > +	no-sdio;
> > +	st,sig-dir;
> > +	st,neg-edge;
> > +	bus-width = <8>;
> > +	vmmc-supply = <&v3v3>;
> > +	status = "okay";
> > +};
> > +
> > +&spi1 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&spi1_pins_a>;
> > +	status = "disabled";
> > +};
> > +
> > +&timers2 {
> > +	/* spare dmas for other usage (un-delete to enable pwm capture) */
> > +	/delete-property/dmas;
> > +	/delete-property/dma-names;
> > +	status = "disabled";
> > +	pwm {
> > +		pinctrl-0 = <&pwm2_pins_a>;
> > +		pinctrl-names = "default";
> > +		status = "okay";
> > +	};
> > +	timer at 1 {
> > +		status = "okay";
> > +	};
> > +};
> > +
> > +&timers6 {
> > +	status = "okay";
> > +	/* spare dmas for other usage */
> > +	/delete-property/dmas;
> > +	/delete-property/dma-names;
> > +	timer at 5 {
> > +		status = "okay";
> > +	};
> > +};
> > +
> > +&timers8 {
> > +	/delete-property/dmas;
> > +	/delete-property/dma-names;
> > +	status = "disabled";
> > +	pwm {
> > +		pinctrl-0 = <&pwm8_pins_a>;
> > +		pinctrl-names = "default";
> > +		status = "okay";
> > +	};
> > +	timer at 7 {
> > +		status = "okay";
> > +	};
> > +};
> > +
> > +&timers12 {
> > +	/delete-property/dmas;
> > +	/delete-property/dma-names;
> > +	status = "disabled";
> > +	pwm {
> > +		pinctrl-0 = <&pwm12_pins_a>;
> > +		pinctrl-names = "default";
> > +		status = "okay";
> > +	};
> > +	timer at 11 {
> > +		status = "okay";
> > +	};
> > +};
> > +
> > +&uart4 {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&uart4_pins_a>;
> > +	status = "okay";
> > +};
> > +
> > +&usbh_ehci {
> > +	phys = <&usbphyc_port0>;
> > +	phy-names = "usb";
> > +	status = "okay";
> > +};
> > +
> > +&usbotg_hs {
> > +	dr_mode = "peripheral";
> > +	phys = <&usbphyc_port1 0>;
> > +	phy-names = "usb2-phy";
> > +	vbus-supply = <&vbus_otg>;
> > +	status = "okay";
> > +};
> > +
> > +&usbphyc {
> > +	status = "okay";
> > +};
> > +
> > +&usbphyc_port0 {
> > +	phy-supply = <&vdd_usb>;
> > +};
> > +
> > +&usbphyc_port1 {
> > +	phy-supply = <&vdd_usb>;
> > +};
> > diff --git a/arch/arm/mach-stm32mp/Kconfig
> > b/arch/arm/mach-stm32mp/Kconfig index ae28f6e206..1aa5f8a122 100644
> > --- a/arch/arm/mach-stm32mp/Kconfig
> > +++ b/arch/arm/mach-stm32mp/Kconfig
> > @@ -147,5 +147,6 @@ config DEBUG_UART_CLOCK  endif
> >
> >  source "board/st/stm32mp1/Kconfig"
> > +source "board/dhelectronics/dh_stm32mp1/Kconfig"
> >
> >  endif
> > diff --git a/board/dhelectronics/dh_stm32mp1/Kconfig
> > b/board/dhelectronics/dh_stm32mp1/Kconfig
> > new file mode 100644
> > index 0000000000..e751a3e5ed
> > --- /dev/null
> > +++ b/board/dhelectronics/dh_stm32mp1/Kconfig
> > @@ -0,0 +1,25 @@
> > +config TARGET_DH_STM32MP1_PDK2
> > +	bool "support of DH STM32MP1 PDK2"
> > +	default y
> 
> Avoid set default y here....
> to avoid to activate this config for ST board.
> 
> In fact it should be a choice between the 2 targets
> - TARGET_DH_STM32MP1_PDK2
> - TARGET_ST_STM32MP1
> 
> > +
> > +if TARGET_DH_STM32MP1_PDK2
> > +
> > +config SYS_BOARD
> > +	default "dh_stm32mp1"
> > +
> > +config SYS_VENDOR
> > +	default "dhelectronics"
> > +
> > +config SYS_CONFIG_NAME
> > +	default "stm32mp1"
> > +
> > +config ENV_SECT_SIZE
> > +	default 0x10000 if ENV_IS_IN_SPI_FLASH
> > +
> > +config ENV_OFFSET
> > +	default 0x1E0000 if ENV_IS_IN_SPI_FLASH
> > +
> > +config ENV_OFFSET_REDUND
> > +	default 0x1F0000 if ENV_IS_IN_SPI_FLASH
> > +
> > +endif
> > diff --git a/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> > b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> > new file mode 100644
> > index 0000000000..38f54a3da4
> > --- /dev/null
> > +++ b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
> > @@ -0,0 +1,7 @@
> > +DH_STM32MP1_PDK2 BOARD
> > +M:	Marek Vasut <marex at denx.de>
> > +S:	Maintained
> > +F:	arch/arm/dts/stm32mp157c-dhcom*
> > +F:	board/dhelectronics/dh_stm32mp1/
> > +F:	configs/stm32mp15_dhcom_basic_defconfig
> > +F:	include/configs/stm32mp1.h
> > diff --git a/board/dhelectronics/dh_stm32mp1/Makefile
> > b/board/dhelectronics/dh_stm32mp1/Makefile
> > new file mode 100644
> > index 0000000000..a9d28218ef
> > --- /dev/null
> > +++ b/board/dhelectronics/dh_stm32mp1/Makefile
> > @@ -0,0 +1,12 @@
> > +# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause # # Copyright (C)
> > +2018, STMicroelectronics - All Rights Reserved #
> > +
> > +ifdef CONFIG_SPL_BUILD
> > +obj-y += ../../st/stm32mp1/spl.o
> > +else
> > +obj-$(CONFIG_CMD_STBOARD) += ../../st/stm32mp1/cmd_stboard.o endif
> > +
> 
> I don't think you wee to support the command STMicroelctronics board (ref
> MBxxxx).
> it is only a internal command for ST : save/read board id in OTP.
> 
> > +obj-y += ../../st/stm32mp1/board.o board.o
> > diff --git a/board/dhelectronics/dh_stm32mp1/board.c
> > b/board/dhelectronics/dh_stm32mp1/board.c
> > new file mode 100644
> > index 0000000000..54cc3b7587
> > --- /dev/null
> > +++ b/board/dhelectronics/dh_stm32mp1/board.c
> > @@ -0,0 +1,777 @@
> > +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
> > +/*
> > + * Copyright (C) 2018, STMicroelectronics - All Rights Reserved  */
> > +
> > +#include <common.h>
> > +#include <adc.h>
> > +#include <asm/arch/stm32.h>
> > +#include <asm/arch/sys_proto.h>
> > +#include <asm/gpio.h>
> > +#include <asm/io.h>
> > +#include <bootm.h>
> > +#include <clk.h>
> > +#include <config.h>
> > +#include <dm.h>
> > +#include <dm/device.h>
> > +#include <dm/uclass.h>
> > +#include <env.h>
> > +#include <env_internal.h>
> > +#include <g_dnl.h>
> > +#include <generic-phy.h>
> > +#include <i2c.h>
> > +#include <i2c_eeprom.h>
> > +#include <init.h>
> > +#include <led.h>
> > +#include <memalign.h>
> > +#include <misc.h>
> > +#include <mtd.h>
> > +#include <mtd_node.h>
> > +#include <netdev.h>
> > +#include <phy.h>
> > +#include <power/regulator.h>
> > +#include <remoteproc.h>
> > +#include <reset.h>
> > +#include <syscon.h>
> > +#include <usb.h>
> > +#include <usb/dwc2_udc.h>
> > +#include <watchdog.h>
> > +
> > +/* SYSCFG registers */
> > +#define SYSCFG_BOOTR		0x00
> > +#define SYSCFG_PMCSETR		0x04
> > +#define SYSCFG_IOCTRLSETR	0x18
> > +#define SYSCFG_ICNR		0x1C
> > +#define SYSCFG_CMPCR		0x20
> > +#define SYSCFG_CMPENSETR	0x24
> > +#define SYSCFG_PMCCLRR		0x44
> > +
> > +#define SYSCFG_BOOTR_BOOT_MASK		GENMASK(2, 0)
> > +#define SYSCFG_BOOTR_BOOTPD_SHIFT	4
> > +
> > +#define SYSCFG_IOCTRLSETR_HSLVEN_TRACE		BIT(0)
> > +#define SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI	BIT(1)
> > +#define SYSCFG_IOCTRLSETR_HSLVEN_ETH		BIT(2)
> > +#define SYSCFG_IOCTRLSETR_HSLVEN_SDMMC		BIT(3)
> > +#define SYSCFG_IOCTRLSETR_HSLVEN_SPI		BIT(4)
> > +
> > +#define SYSCFG_CMPCR_SW_CTRL		BIT(1)
> > +#define SYSCFG_CMPCR_READY		BIT(8)
> > +
> > +#define SYSCFG_CMPENSETR_MPU_EN		BIT(0)
> > +
> > +#define SYSCFG_PMCSETR_ETH_CLK_SEL	BIT(16)
> > +#define SYSCFG_PMCSETR_ETH_REF_CLK_SEL	BIT(17)
> > +
> > +#define SYSCFG_PMCSETR_ETH_SELMII	BIT(20)
> > +
> > +#define SYSCFG_PMCSETR_ETH_SEL_MASK	GENMASK(23, 21)
> > +#define SYSCFG_PMCSETR_ETH_SEL_GMII_MII	0
> > +#define SYSCFG_PMCSETR_ETH_SEL_RGMII	BIT(21)
> > +#define SYSCFG_PMCSETR_ETH_SEL_RMII	BIT(23)
> > +
> > +/*
> > + * Get a global data pointer
> > + */
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +int setup_mac_address(void)
> > +{
> > +	struct udevice *dev;
> > +	ofnode eeprom;
> > +	unsigned char enetaddr[6];
> > +	int ret;
> > +
> > +	ret = eth_env_get_enetaddr("ethaddr", enetaddr);
> > +	if (ret)	/* ethaddr is already set */
> > +		return 0;
> > +
> > +	eeprom = ofnode_path("/soc/i2c at 5c002000/eeprom at 50");
> > +	if (!ofnode_valid(eeprom)) {
> > +		printf("Invalid hardware path to EEPROM!\n");
> > +		return -ENODEV;
> > +	}
> > +
> > +	ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom,
> > &dev);
> > +	if (ret) {
> > +		printf("Cannot find EEPROM!\n");
> > +		return ret;
> > +	}
> > +
> > +	ret = i2c_eeprom_read(dev, 0xfa, enetaddr, 0x6);
> > +	if (ret) {
> > +		printf("Error reading configuration EEPROM!\n");
> > +		return ret;
> > +	}
> > +
> > +	if (is_valid_ethaddr(enetaddr))
> > +		eth_env_set_enetaddr("ethaddr", enetaddr);
> > +
> > +	return 0;
> > +}
> > +
> > +int checkboard(void)
> > +{
> > +	int ret;
> > +	char *mode;
> > +	u32 otp;
> > +	struct udevice *dev;
> > +	const char *fdt_compat;
> > +	int fdt_compat_len;
> > +
> > +	if (IS_ENABLED(CONFIG_STM32MP1_OPTEE))
> > +		mode = "trusted with OP-TEE";
> > +	else if (IS_ENABLED(CONFIG_STM32MP1_TRUSTED))
> > +		mode = "trusted";
> > +	else
> > +		mode = "basic";
> > +
> > +	printf("Board: stm32mp1 in %s mode", mode);
> > +	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
> > +				 &fdt_compat_len);
> > +	if (fdt_compat && fdt_compat_len)
> > +		printf(" (%s)", fdt_compat);
> > +	puts("\n");
> > +
> > +	ret = uclass_get_device_by_driver(UCLASS_MISC,
> > +					  DM_GET_DRIVER(stm32mp_bsec),
> > +					  &dev);
> > +
> > +	if (!ret)
> > +		ret = misc_read(dev,
> > STM32_BSEC_SHADOW(BSEC_OTP_BOARD),
> > +				&otp, sizeof(otp));
> > +	if (ret > 0 && otp) {
> > +		printf("Board: MB%04x Var%d Rev.%c-%02d\n",
> > +		       otp >> 16,
> > +		       (otp >> 12) & 0xF,
> > +		       ((otp >> 8) & 0xF) - 1 + 'A',
> > +		       otp & 0xF);
> > +	}
> 
> This part (read OTP / / display MBxxx ) can be dropped for your board (it is a ST
> specific part).
> 
> > +	return 0;
> > +}
> > +
> > +static void board_key_check(void)
> > +{
> > +#if defined(CONFIG_FASTBOOT) || defined(CONFIG_CMD_STM32PROG)
> > +	ofnode node;
> > +	struct gpio_desc gpio;
> > +	enum forced_boot_mode boot_mode = BOOT_NORMAL;
> > +
> > +	node = ofnode_path("/config");
> > +	if (!ofnode_valid(node)) {
> > +		debug("%s: no /config node?\n", __func__);
> > +		return;
> > +	}
> > +#ifdef CONFIG_FASTBOOT
> > +	if (gpio_request_by_name_nodev(node, "st,fastboot-gpios", 0,
> > +				       &gpio, GPIOD_IS_IN)) {
> > +		debug("%s: could not find a /config/st,fastboot-gpios\n",
> > +		      __func__);
> > +	} else {
> > +		if (dm_gpio_get_value(&gpio)) {
> > +			puts("Fastboot key pressed, ");
> > +			boot_mode = BOOT_FASTBOOT;
> > +		}
> > +
> > +		dm_gpio_free(NULL, &gpio);
> > +	}
> > +#endif
> > +#ifdef CONFIG_CMD_STM32PROG
> > +	if (gpio_request_by_name_nodev(node, "st,stm32prog-gpios", 0,
> > +				       &gpio, GPIOD_IS_IN)) {
> > +		debug("%s: could not find a /config/st,stm32prog-gpios\n",
> > +		      __func__);
> > +	} else {
> > +		if (dm_gpio_get_value(&gpio)) {
> > +			puts("STM32Programmer key pressed, ");
> > +			boot_mode = BOOT_STM32PROG;
> > +		}
> > +		dm_gpio_free(NULL, &gpio);
> > +	}
> > +#endif
> > +
> > +	if (boot_mode != BOOT_NORMAL) {
> > +		puts("entering download mode...\n");
> > +		clrsetbits_le32(TAMP_BOOT_CONTEXT,
> > +				TAMP_BOOT_FORCED_MASK,
> > +				boot_mode);
> > +	}
> > +#endif
> > +}
> 
> Do you support GPIO key press on  GPAIOA14 / 15 (as it is done in ST boards
> EV1 : DK1 / DK2) If no all this function can be dropped.
> 
> > +#if defined(CONFIG_USB_GADGET) &&
> > defined(CONFIG_USB_GADGET_DWC2_OTG)
> > +
> > +/* STMicroelectronics STUSB1600 Type-C controller */
> > +#define STUSB1600_CC_CONNECTION_STATUS		0x0E
> > +
> > +/* STUSB1600_CC_CONNECTION_STATUS bitfields */
> > +#define STUSB1600_CC_ATTACH			BIT(0)
> > +
> > +static int stusb1600_init(struct udevice **dev_stusb1600) {
> > +	ofnode node;
> > +	struct udevice *dev, *bus;
> > +	int ret;
> > +	u32 chip_addr;
> > +
> > +	*dev_stusb1600 = NULL;
> > +
> > +	/* if node stusb1600 is present, means DK1 or DK2 board */
> > +	node = ofnode_by_compatible(ofnode_null(), "st,stusb1600");
> > +	if (!ofnode_valid(node))
> > +		return -ENODEV;
> > +
> > +	ret = ofnode_read_u32(node, "reg", &chip_addr);
> > +	if (ret)
> > +		return -EINVAL;
> > +
> > +	ret = uclass_get_device_by_ofnode(UCLASS_I2C,
> > ofnode_get_parent(node),
> > +					  &bus);
> > +	if (ret) {
> > +		printf("bus for stusb1600 not found\n");
> > +		return -ENODEV;
> > +	}
> > +
> > +	ret = dm_i2c_probe(bus, chip_addr, 0, &dev);
> > +	if (!ret)
> > +		*dev_stusb1600 = dev;
> > +
> > +	return ret;
> > +}
> > +
> > +static int stusb1600_cable_connected(struct udevice *dev) {
> > +	u8 status;
> > +
> > +	if (dm_i2c_read(dev, STUSB1600_CC_CONNECTION_STATUS, &status,
> > 1))
> > +		return 0;
> > +
> > +	return status & STUSB1600_CC_ATTACH; }
> > +
> > +#include <usb/dwc2_udc.h>
> > +int g_dnl_board_usb_cable_connected(void)
> > +{
> > +	struct udevice *stusb1600;
> > +	struct udevice *dwc2_udc_otg;
> > +	int ret;
> > +
> > +	if (!stusb1600_init(&stusb1600))
> > +		return stusb1600_cable_connected(stusb1600);
> > +
> > +	ret = uclass_get_device_by_driver(UCLASS_USB_GADGET_GENERIC,
> > +					  DM_GET_DRIVER(dwc2_udc_otg),
> > +					  &dwc2_udc_otg);
> > +	if (!ret)
> > +		debug("dwc2_udc_otg init failed\n");
> > +
> > +	return dwc2_udc_B_session_valid(dwc2_udc_otg);
> > +}
> > +
> 
> If you don't have STUSB1600 (external usb typeC controller) All this part can
> dropped.
> 
> > +#define STM32MP1_G_DNL_DFU_PRODUCT_NUM 0xdf11 #define
> > +STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM 0x0afb
> > +
> > +int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char
> > +*name) {
> > +	if (!strcmp(name, "usb_dnl_dfu"))
> > +		put_unaligned(STM32MP1_G_DNL_DFU_PRODUCT_NUM, &dev-
> > >idProduct);
> > +	else if (!strcmp(name, "usb_dnl_fastboot"))
> > +
> > 	put_unaligned(STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM,
> > +			      &dev->idProduct);
> > +	else
> > +		put_unaligned(CONFIG_USB_GADGET_PRODUCT_NUM, &dev-
> > >idProduct);
> > +
> > +	return 0;
> > +}
> > +
> > +#endif /* CONFIG_USB_GADGET */
> > +
> > +#ifdef CONFIG_LED
> > +static int get_led(struct udevice **dev, char *led_string) {
> > +	char *led_name;
> > +	int ret;
> > +
> > +	led_name = fdtdec_get_config_string(gd->fdt_blob, led_string);
> > +	if (!led_name) {
> > +		pr_debug("%s: could not find %s config string\n",
> > +			 __func__, led_string);
> > +		return -ENOENT;
> > +	}
> > +	ret = led_get_by_label(led_name, dev);
> > +	if (ret) {
> > +		debug("%s: get=%d\n", __func__, ret);
> > +		return ret;
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static int setup_led(enum led_state_t cmd) {
> > +	struct udevice *dev;
> > +	int ret;
> > +
> > +	ret = get_led(&dev, "u-boot,boot-led");
> > +	if (ret)
> > +		return ret;
> > +
> > +	ret = led_set_state(dev, cmd);
> > +	return ret;
> > +}
> > +#endif
> > +
> > +static void __maybe_unused led_error_blink(u32 nb_blink) { #ifdef
> > +CONFIG_LED
> > +	int ret;
> > +	struct udevice *led;
> > +	u32 i;
> > +#endif
> > +
> > +	if (!nb_blink)
> > +		return;
> > +
> > +#ifdef CONFIG_LED
> > +	ret = get_led(&led, "u-boot,error-led");
> > +	if (!ret) {
> > +		/* make u-boot,error-led blinking */
> > +		/* if U32_MAX and 125ms interval, for 17.02 years */
> > +		for (i = 0; i < 2 * nb_blink; i++) {
> > +			led_set_state(led, LEDST_TOGGLE);
> > +			mdelay(125);
> > +			WATCHDOG_RESET();
> > +		}
> > +	}
> > +#endif
> > +
> > +	/* infinite: the boot process must be stopped */
> > +	if (nb_blink == U32_MAX)
> > +		hang();
> > +}
> > +
> > +static void sysconf_init(void)
> > +{
> > +#ifndef CONFIG_STM32MP1_TRUSTED
> > +	u8 *syscfg;
> > +#ifdef CONFIG_DM_REGULATOR
> > +	struct udevice *pwr_dev;
> > +	struct udevice *pwr_reg;
> > +	struct udevice *dev;
> > +	int ret;
> > +	u32 otp = 0;
> > +#endif
> > +	u32 bootr;
> > +
> > +	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
> > +
> > +	/* interconnect update : select master using the port 1 */
> > +	/* LTDC = AXI_M9 */
> > +	/* GPU  = AXI_M8 */
> > +	/* today information is hardcoded in U-Boot */
> > +	writel(BIT(9), syscfg + SYSCFG_ICNR);
> > +
> > +	/* disable Pull-Down for boot pin connected to VDD */
> > +	bootr = readl(syscfg + SYSCFG_BOOTR);
> > +	bootr &= ~(SYSCFG_BOOTR_BOOT_MASK <<
> > SYSCFG_BOOTR_BOOTPD_SHIFT);
> > +	bootr |= (bootr & SYSCFG_BOOTR_BOOT_MASK) <<
> > SYSCFG_BOOTR_BOOTPD_SHIFT;
> > +	writel(bootr, syscfg + SYSCFG_BOOTR);
> > +
> > +#ifdef CONFIG_DM_REGULATOR
> > +	/* High Speed Low Voltage Pad mode Enable for SPI, SDMMC, ETH,
> > QSPI
> > +	 * and TRACE. Needed above ~50MHz and conditioned by AFMUX
> > selection.
> > +	 * The customer will have to disable this for low frequencies
> > +	 * or if AFMUX is selected but the function not used, typically for
> > +	 * TRACE. Otherwise, impact on power consumption.
> > +	 *
> > +	 * WARNING:
> > +	 *   enabling High Speed mode while VDD>2.7V
> > +	 *   with the OTP product_below_2v5 (OTP 18, BIT 13)
> > +	 *   erroneously set to 1 can damage the IC!
> > +	 *   => U-Boot set the register only if VDD < 2.7V (in DT)
> > +	 *      but this value need to be consistent with board design
> > +	 */
> > +	ret = uclass_get_device_by_driver(UCLASS_PMIC,
> > +					  DM_GET_DRIVER(stm32mp_pwr_pmic),
> > +					  &pwr_dev);
> > +	if (!ret) {
> > +		ret = uclass_get_device_by_driver(UCLASS_MISC,
> > +
> > DM_GET_DRIVER(stm32mp_bsec),
> > +						  &dev);
> > +		if (ret) {
> > +			pr_err("Can't find stm32mp_bsec driver\n");
> > +			return;
> > +		}
> > +
> > +		ret = misc_read(dev, STM32_BSEC_SHADOW(18), &otp, 4);
> > +		if (ret > 0)
> > +			otp = otp & BIT(13);
> > +
> > +		/* get VDD = vdd-supply */
> > +		ret = device_get_supply_regulator(pwr_dev, "vdd-supply",
> > +						  &pwr_reg);
> > +
> > +		/* check if VDD is Low Voltage */
> > +		if (!ret) {
> > +			if (regulator_get_value(pwr_reg) < 2700000) {
> > +				writel(SYSCFG_IOCTRLSETR_HSLVEN_TRACE |
> > +				       SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI
> > |
> > +				       SYSCFG_IOCTRLSETR_HSLVEN_ETH |
> > +				       SYSCFG_IOCTRLSETR_HSLVEN_SDMMC |
> > +				       SYSCFG_IOCTRLSETR_HSLVEN_SPI,
> > +				       syscfg + SYSCFG_IOCTRLSETR);
> > +
> > +				if (!otp)
> > +					pr_err("product_below_2v5=0: HSLVEN
> > protected by HW\n");
> > +			} else {
> > +				if (otp)
> > +					pr_err("product_below_2v5=1: HSLVEN
> > update is destructive, no update as VDD>2.7V\n");
> > +			}
> > +		} else {
> > +			debug("VDD unknown");
> > +		}
> > +	}
> > +#endif
> > +
> > +	/* activate automatic I/O compensation
> > +	 * warning: need to ensure CSI enabled and ready in clock driver
> > +	 */
> > +	writel(SYSCFG_CMPENSETR_MPU_EN, syscfg +
> > SYSCFG_CMPENSETR);
> > +
> > +	while (!(readl(syscfg + SYSCFG_CMPCR) & SYSCFG_CMPCR_READY))
> > +		;
> > +	clrbits_le32(syscfg + SYSCFG_CMPCR, SYSCFG_CMPCR_SW_CTRL);
> > #endif }
> > +
> > +/* board dependent setup after realloc */ int board_init(void) {
> > +	struct udevice *dev;
> > +
> > +	/* address of boot parameters */
> > +	gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;
> > +
> > +	/* probe all PINCTRL for hog */
> > +	for (uclass_first_device(UCLASS_PINCTRL, &dev);
> > +	     dev;
> > +	     uclass_next_device(&dev)) {
> > +		pr_debug("probe pincontrol = %s\n", dev->name);
> > +	}
> > +
> > +	board_key_check();
> > +
> > +#ifdef CONFIG_DM_REGULATOR
> > +	regulators_enable_boot_on(_DEBUG);
> > +#endif
> > +
> > +	sysconf_init();
> > +
> > +	if (CONFIG_IS_ENABLED(CONFIG_LED))
> > +		led_default_state();
> > +
> > +	return 0;
> > +}
> > +
> > +int board_late_init(void)
> > +{
> > +	char *boot_device;
> > +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
> > +	const void *fdt_compat;
> > +	int fdt_compat_len;
> > +	int ret;
> > +	u32 otp;
> > +	struct udevice *dev;
> > +	char buf[10];
> > +
> > +	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
> > +				 &fdt_compat_len);
> > +	if (fdt_compat && fdt_compat_len) {
> > +		if (strncmp(fdt_compat, "st,", 3) != 0)
> > +			env_set("board_name", fdt_compat);
> > +		else
> > +			env_set("board_name", fdt_compat + 3);
> > +	}
> > +	ret = uclass_get_device_by_driver(UCLASS_MISC,
> > +					  DM_GET_DRIVER(stm32mp_bsec),
> > +					  &dev);
> > +
> > +	if (!ret)
> > +		ret = misc_read(dev,
> > STM32_BSEC_SHADOW(BSEC_OTP_BOARD),
> > +				&otp, sizeof(otp));
> > +	if (!ret && otp) {
> > +		snprintf(buf, sizeof(buf), "0x%04x", otp >> 16);
> > +		env_set("board_id", buf);
> > +
> > +		snprintf(buf, sizeof(buf), "0x%04x",
> > +			 ((otp >> 8) & 0xF) - 1 + 0xA);
> > +		env_set("board_rev", buf);
> > +	}
> > +#endif
> > +
> > +	/* Check the boot-source to disable bootdelay */
> > +	boot_device = env_get("boot_device");
> > +	if (!strcmp(boot_device, "serial") || !strcmp(boot_device, "usb"))
> > +		env_set("bootdelay", "0");
> > +
> > +	return 0;
> > +}
> > +
> > +void board_quiesce_devices(void)
> > +{
> > +#ifdef CONFIG_LED
> > +	setup_led(LEDST_OFF);
> > +#endif
> > +}
> > +
> > +/* eth init function : weak called in eqos driver */ int
> > +board_interface_eth_init(struct udevice *dev,
> > +			     phy_interface_t interface_type) {
> > +	u8 *syscfg;
> > +	u32 value;
> > +	bool eth_clk_sel_reg = false;
> > +	bool eth_ref_clk_sel_reg = false;
> > +
> > +	/* Gigabit Ethernet 125MHz clock selection. */
> > +	eth_clk_sel_reg = dev_read_bool(dev, "st,eth_clk_sel");
> > +
> > +	/* Ethernet 50Mhz RMII clock selection */
> > +	eth_ref_clk_sel_reg =
> > +		dev_read_bool(dev, "st,eth_ref_clk_sel");
> > +
> > +	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
> > +
> > +	if (!syscfg)
> > +		return -ENODEV;
> > +
> > +	switch (interface_type) {
> > +	case PHY_INTERFACE_MODE_MII:
> > +		value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
> > +			SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
> > +		debug("%s: PHY_INTERFACE_MODE_MII\n", __func__);
> > +		break;
> > +	case PHY_INTERFACE_MODE_GMII:
> > +		if (eth_clk_sel_reg)
> > +			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
> > +				SYSCFG_PMCSETR_ETH_CLK_SEL;
> > +		else
> > +			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII;
> > +		debug("%s: PHY_INTERFACE_MODE_GMII\n", __func__);
> > +		break;
> > +	case PHY_INTERFACE_MODE_RMII:
> > +		if (eth_ref_clk_sel_reg)
> > +			value = SYSCFG_PMCSETR_ETH_SEL_RMII |
> > +				SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
> > +		else
> > +			value = SYSCFG_PMCSETR_ETH_SEL_RMII;
> > +		debug("%s: PHY_INTERFACE_MODE_RMII\n", __func__);
> > +		break;
> > +	case PHY_INTERFACE_MODE_RGMII:
> > +	case PHY_INTERFACE_MODE_RGMII_ID:
> > +	case PHY_INTERFACE_MODE_RGMII_RXID:
> > +	case PHY_INTERFACE_MODE_RGMII_TXID:
> > +		if (eth_clk_sel_reg)
> > +			value = SYSCFG_PMCSETR_ETH_SEL_RGMII |
> > +				SYSCFG_PMCSETR_ETH_CLK_SEL;
> > +		else
> > +			value = SYSCFG_PMCSETR_ETH_SEL_RGMII;
> > +		debug("%s: PHY_INTERFACE_MODE_RGMII\n", __func__);
> > +		break;
> > +	default:
> > +		debug("%s: Do not manage %d interface\n",
> > +		      __func__, interface_type);
> > +		/* Do not manage others interfaces */
> > +		return -EINVAL;
> > +	}
> > +
> > +	/* clear and set ETH configuration bits */
> > +	writel(SYSCFG_PMCSETR_ETH_SEL_MASK |
> > SYSCFG_PMCSETR_ETH_SELMII |
> > +	       SYSCFG_PMCSETR_ETH_REF_CLK_SEL |
> > SYSCFG_PMCSETR_ETH_CLK_SEL,
> > +	       syscfg + SYSCFG_PMCCLRR);
> > +	writel(value, syscfg + SYSCFG_PMCSETR);
> > +
> > +	return 0;
> > +}
> > +
> > +enum env_location env_get_location(enum env_operation op, int prio) {
> > +	if (prio)
> > +		return ENVL_UNKNOWN;
> > +
> > +#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
> > +	return ENVL_SPI_FLASH;
> > +#else
> > +	return ENVL_NOWHERE;
> > +#endif
> > +}
> > +
> > +#ifdef CONFIG_SYS_MTDPARTS_RUNTIME
> > +
> > +#define MTDPARTS_LEN		256
> > +#define MTDIDS_LEN		128
> > +
> > +/**
> > + * The mtdparts_nand0 and mtdparts_nor0 variable tends to be long.
> > + * If we need to access it before the env is relocated, then we need
> > + * to use our own stack buffer. gd->env_buf will be too small.
> > + *
> > + * @param buf temporary buffer pointer MTDPARTS_LEN long
> > + * @return mtdparts variable string, NULL if not found  */ static
> > +const char *env_get_mtdparts(const char *str, char *buf) {
> > +	if (gd->flags & GD_FLG_ENV_READY)
> > +		return env_get(str);
> > +	if (env_get_f(str, buf, MTDPARTS_LEN) != -1)
> > +		return buf;
> > +
> > +	return NULL;
> > +}
> > +
> > +/**
> > + * update the variables "mtdids" and "mtdparts" with content of
> > +mtdparts_<dev>  */ static void board_get_mtdparts(const char *dev,
> > +			       char *mtdids,
> > +			       char *mtdparts)
> > +{
> > +	char env_name[32] = "mtdparts_";
> > +	char tmp_mtdparts[MTDPARTS_LEN];
> > +	const char *tmp;
> > +
> > +	/* name of env variable to read = mtdparts_<dev> */
> > +	strcat(env_name, dev);
> > +	tmp = env_get_mtdparts(env_name, tmp_mtdparts);
> > +	if (tmp) {
> > +		/* mtdids: "<dev>=<dev>, ...." */
> > +		if (mtdids[0] != '\0')
> > +			strcat(mtdids, ",");
> > +		strcat(mtdids, dev);
> > +		strcat(mtdids, "=");
> > +		strcat(mtdids, dev);
> > +
> > +		/* mtdparts: "mtdparts=<dev>:<mtdparts_<dev>>;..." */
> > +		if (mtdparts[0] != '\0')
> > +			strncat(mtdparts, ";", MTDPARTS_LEN);
> > +		else
> > +			strcat(mtdparts, "mtdparts=");
> > +		strncat(mtdparts, dev, MTDPARTS_LEN);
> > +		strncat(mtdparts, ":", MTDPARTS_LEN);
> > +		strncat(mtdparts, tmp, MTDPARTS_LEN);
> > +	}
> > +}
> > +
> > +void board_mtdparts_default(const char **mtdids, const char
> > +**mtdparts) {
> > +	struct udevice *dev;
> > +	static char parts[3 * MTDPARTS_LEN + 1];
> > +	static char ids[MTDIDS_LEN + 1];
> > +	static bool mtd_initialized;
> > +
> > +	if (mtd_initialized) {
> > +		*mtdids = ids;
> > +		*mtdparts = parts;
> > +		return;
> > +	}
> > +
> > +	memset(parts, 0, sizeof(parts));
> > +	memset(ids, 0, sizeof(ids));
> > +
> > +	/* probe all MTD devices */
> > +	for (uclass_first_device(UCLASS_MTD, &dev);
> > +	     dev;
> > +	     uclass_next_device(&dev)) {
> > +		pr_debug("mtd device = %s\n", dev->name);
> > +	}
> > +
> > +	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
> > +		board_get_mtdparts("nor0", ids, parts);
> > +
> > +	mtd_initialized = true;
> > +	*mtdids = ids;
> > +	*mtdparts = parts;
> > +	debug("%s:mtdids=%s & mtdparts=%s\n", __func__, ids, parts); }
> > +#endif
> > +
> > +#if defined(CONFIG_OF_BOARD_SETUP)
> > +int ft_board_setup(void *blob, bd_t *bd) {
> > +	return 0;
> > +}
> > +#endif
> > +
> > +#ifdef CONFIG_SET_DFU_ALT_INFO
> > +#define DFU_ALT_BUF_LEN SZ_1K
> > +
> > +static void board_get_alt_info(const char *dev, char *buff) {
> > +	char var_name[32] = "dfu_alt_info_";
> > +	int ret;
> > +
> > +	ALLOC_CACHE_ALIGN_BUFFER(char, tmp_alt, DFU_ALT_BUF_LEN);
> > +
> > +	/* name of env variable to read = dfu_alt_info_<dev> */
> > +	strcat(var_name, dev);
> > +	ret = env_get_f(var_name, tmp_alt, DFU_ALT_BUF_LEN);
> > +	if (ret) {
> > +		if (buff[0] != '\0')
> > +			strcat(buff, "&");
> > +		strncat(buff, tmp_alt, DFU_ALT_BUF_LEN);
> > +	}
> > +}
> > +
> > +void set_dfu_alt_info(char *interface, char *devstr) {
> > +	struct udevice *dev;
> > +
> > +	ALLOC_CACHE_ALIGN_BUFFER(char, buf, DFU_ALT_BUF_LEN);
> > +
> > +	if (env_get("dfu_alt_info"))
> > +		return;
> > +
> > +	memset(buf, 0, sizeof(buf));
> > +
> > +	/* probe all MTD devices */
> > +	mtd_probe_devices();
> > +
> > +	board_get_alt_info("ram", buf);
> > +
> > +	if (!uclass_get_device(UCLASS_MMC, 0, &dev))
> > +		board_get_alt_info("mmc0", buf);
> > +
> > +	if (!uclass_get_device(UCLASS_MMC, 1, &dev))
> > +		board_get_alt_info("mmc1", buf);
> > +
> > +	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
> > +		board_get_alt_info("nor0", buf);
> > +
> > +	env_set("dfu_alt_info", buf);
> > +	puts("DFU alt info setting: done\n"); } #endif
> > +
> > +static void board_copro_image_process(ulong fw_image, size_t fw_size) {
> > +	int ret, id = 0; /* Copro id fixed to 0 as only one coproc on mp1 */
> > +
> > +	if (!rproc_is_initialized())
> > +		if (rproc_init()) {
> > +			printf("Remote Processor %d initialization failed\n",
> > +			       id);
> > +			return;
> > +		}
> > +
> > +	ret = rproc_load(id, fw_image, fw_size);
> > +	printf("Load Remote Processor %d with data at addr=0x%08lx %u
> > bytes:%s\n",
> > +	       id, fw_image, fw_size, ret ? " Failed!" : " Success!");
> > +
> > +	if (!ret) {
> > +		rproc_start(id);
> > +		env_set("copro_state", "booted");
> > +	}
> > +}
> > +
> > +U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_COPRO,
> > board_copro_image_process);
> > diff --git a/configs/stm32mp15_dhcom_basic_defconfig
> > b/configs/stm32mp15_dhcom_basic_defconfig
> > new file mode 100644
> > index 0000000000..e4f331a913
> > --- /dev/null
> > +++ b/configs/stm32mp15_dhcom_basic_defconfig
> > @@ -0,0 +1,140 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_STM32MP=y
> > +CONFIG_SYS_MALLOC_F_LEN=0x3000
> > +CONFIG_SPL_MMC_SUPPORT=y
> > +CONFIG_ENV_SIZE=0x4000
> > +CONFIG_SPL=y
> > +CONFIG_TARGET_STM32MP1=y
> > +# CONFIG_TARGET_STM32MP157C_DK2 is not set
> 
> CONFIG_TARGET_DH_STM32MP1_PDK2=y
> 
> > +CONFIG_SPL_SPI_FLASH_SUPPORT=y CONFIG_SPL_SPI_SUPPORT=y #
> > +CONFIG_ARMV7_VIRT is not set
> > +CONFIG_SPL_TEXT_BASE=0x2FFC2500
> > +CONFIG_DISTRO_DEFAULTS=y
> > +CONFIG_FIT=y
> > +# CONFIG_BOOTSTAGE is not set
> > +CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
> > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
> > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
> > +CONFIG_SPL_I2C_SUPPORT=y
> > +CONFIG_SPL_MTD_SUPPORT=y
> > +CONFIG_SPL_POWER_SUPPORT=y
> > +CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
> > +CONFIG_SYS_PROMPT="STM32MP> "
> > +# CONFIG_CMD_BOOTD is not set
> > +# CONFIG_CMD_ELF is not set
> > +# CONFIG_CMD_IMI is not set
> > +# CONFIG_CMD_XIMG is not set
> > +# CONFIG_CMD_EXPORTENV is not set
> > +CONFIG_CMD_EEPROM=y
> > +CONFIG_CMD_MEMINFO=y
> > +CONFIG_CMD_MEMTEST=y
> > +CONFIG_CMD_ADC=y
> > +CONFIG_CMD_CLK=y
> > +CONFIG_CMD_DFU=y
> > +CONFIG_CMD_FUSE=y
> > +CONFIG_CMD_GPIO=y
> > +CONFIG_CMD_GPT=y
> > +CONFIG_CMD_I2C=y
> > +CONFIG_CMD_MMC=y
> > +CONFIG_CMD_MTD=y
> > +CONFIG_CMD_REMOTEPROC=y
> > +CONFIG_CMD_SPI=y
> > +CONFIG_CMD_USB=y
> > +CONFIG_CMD_USB_MASS_STORAGE=y
> > +CONFIG_CMD_BMP=y
> > +CONFIG_CMD_CACHE=y
> > +CONFIG_CMD_TIME=y
> > +CONFIG_CMD_TIMER=y
> > +CONFIG_CMD_PMIC=y
> > +CONFIG_CMD_REGULATOR=y
> > +CONFIG_CMD_EXT4_WRITE=y
> > +CONFIG_CMD_MTDPARTS=y
> > +# CONFIG_SPL_DOS_PARTITION is not set
> > +CONFIG_DEFAULT_DEVICE_TREE="stm32mp157c-dhcom-pdk2-u-boot"
> > +CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-
> > extended interrupt-controller \\\#interrupt-cells interrupt-parent
> > dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-
> parents hwlocks"
> > +CONFIG_ENV_IS_IN_SPI_FLASH=y
> > +CONFIG_USE_ENV_SPI_BUS=y
> > +CONFIG_ENV_SPI_BUS=0
> > +CONFIG_USE_ENV_SPI_CS=y
> > +CONFIG_ENV_SPI_CS=0
> > +CONFIG_USE_ENV_SPI_MAX_HZ=y
> > +CONFIG_ENV_SPI_MAX_HZ=10000000
> > +CONFIG_USE_ENV_SPI_MODE=y
> > +CONFIG_ENV_SPI_MODE=0x0
> > +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
> > +CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> > +CONFIG_NET_RANDOM_ETHADDR=y
> > +CONFIG_IP_DEFRAG=y
> > +CONFIG_TFTP_BLOCKSIZE=1536
> > +CONFIG_STM32_ADC=y
> > +CONFIG_SPL_BLOCK_CACHE=y
> > +CONFIG_DFU_MMC=y
> > +CONFIG_DFU_RAM=y
> > +CONFIG_DFU_VIRT=y
> > +CONFIG_DM_HWSPINLOCK=y
> > +CONFIG_HWSPINLOCK_STM32=y
> > +CONFIG_DM_I2C=y
> > +CONFIG_SYS_I2C_STM32F7=y
> > +CONFIG_LED=y
> > +CONFIG_LED_GPIO=y
> > +CONFIG_DM_MAILBOX=y
> > +CONFIG_STM32_IPCC=y
> > +CONFIG_I2C_EEPROM=y
> > +CONFIG_DM_MMC=y
> > +CONFIG_SUPPORT_EMMC_BOOT=y
> > +CONFIG_STM32_SDMMC2=y
> > +CONFIG_MTD=y
> > +CONFIG_DM_SPI_FLASH=y
> > +CONFIG_SPI_FLASH_MACRONIX=y
> > +CONFIG_SPI_FLASH_SPANSION=y
> > +CONFIG_SPI_FLASH_STMICRO=y
> > +CONFIG_SPI_FLASH_WINBOND=y
> > +# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
> > CONFIG_SPI_FLASH_MTD=y
> > +CONFIG_SPL_SPI_FLASH_MTD=y CONFIG_DM_ETH=y
> > CONFIG_DWC_ETH_QOS=y
> > +CONFIG_PHY=y CONFIG_PHY_STM32_USBPHYC=y CONFIG_PINCONF=y
> #
> > +CONFIG_SPL_PINCTRL_FULL is not set CONFIG_PINCTRL_STMFX=y
> > +CONFIG_DM_PMIC=y # CONFIG_SPL_PMIC_CHILDREN is not set
> > +CONFIG_PMIC_STPMIC1=y CONFIG_DM_REGULATOR_FIXED=y
> > +CONFIG_DM_REGULATOR_GPIO=y
> > CONFIG_DM_REGULATOR_STM32_VREFBUF=y
> > +CONFIG_DM_REGULATOR_STPMIC1=y
> > +CONFIG_REMOTEPROC_STM32_COPRO=y
> > +CONFIG_DM_RTC=y
> > +CONFIG_RTC_STM32=y
> > +CONFIG_SERIAL_RX_BUFFER=y
> > +CONFIG_SPI=y
> > +CONFIG_DM_SPI=y
> > +CONFIG_STM32_QSPI=y
> > +CONFIG_STM32_SPI=y
> > +CONFIG_USB=y
> > +CONFIG_DM_USB=y
> > +CONFIG_DM_USB_GADGET=y
> > +CONFIG_USB_EHCI_HCD=y
> > +CONFIG_USB_EHCI_GENERIC=y
> > +CONFIG_USB_GADGET=y
> > +CONFIG_USB_GADGET_MANUFACTURER="dh"
> > +CONFIG_USB_GADGET_VENDOR_NUM=0x0483
> > +CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
> > +CONFIG_USB_GADGET_DWC2_OTG=y
> > +CONFIG_USB_GADGET_DOWNLOAD=y
> > +CONFIG_USB_HOST_ETHER=y
> > +CONFIG_USB_ETHER_ASIX=y
> > +CONFIG_DM_VIDEO=y
> > +CONFIG_BACKLIGHT_GPIO=y
> > +CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
> > +CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
> > +CONFIG_VIDEO_STM32=y
> > +CONFIG_VIDEO_STM32_DSI=y
> > +CONFIG_VIDEO_STM32_MAX_XRES=1280
> > +CONFIG_VIDEO_STM32_MAX_YRES=800
> > +CONFIG_LZO=y
> > +CONFIG_FDT_FIXUP_PARTITIONS=y
> > --
> > 2.24.1
> >
> 
> Regards
> 
> Patrick
Marek Vasut Jan. 20, 2020, 8:21 p.m. UTC | #3
On 1/17/20 5:32 PM, Patrick DELAUNAY wrote:
> Hi Marek,

Hi,

>> From: Patrick DELAUNAY
>> Sent: lundi 13 janvier 2020 15:05
>>
>> Hi Marek,
>>
>>> From: Marek Vasut <marex at denx.de>
>>> Sent: vendredi 10 janvier 2020 01:29
>>>
>>> Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier board.
>>> This is an SoM with STM32MP157C and an evaluation kit. The baseboard
>>> provides Ethernet, UART, USB, CAN and optional display.
>>> Signed-off-by: Marek Vasut <marex at denx.de>
>>> Cc: Patrick Delaunay <patrick.delaunay at st.com>
>>> Cc: Patrice Chotard <patrice.chotard at st.com>
>>> ---
> 
> For information, I merge the serie, except this patch 5/5 on master brach and I sent a pull request for u-boot-stm32-20200117.
> 
> For this patch, I propose a rebase and also many modification liked to my previous remark
> (I remove ST only parts for stboard command, and also led and key management) .
> 
> This proposal is present in the branch https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/next
> 	https://gitlab.denx.de/u-boot/custodians/u-boot-stm/commit/db48e11b1eccf23f3f9ba26e886a798e74df6a01
> 
> your initial patch is in applied https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/dh
> 	
> 
> Can you test the "next" branch and check the difference with your initial patch ( applied in dh branch
> https://gitlab.denx.de/u-boot/custodians/u-boot-stm/tree/dh 
> => https://gitlab.denx.de/u-boot/custodians/u-boot-stm/commit/0ab3ce72f82b946ac0924dfcdc082792f325eb68 )
> 
> I hope that I don't remove something really present on the SOM.
> 
> If you are OK, can you send a V2 version with the "next" branch content and I will integrate it in master branch for next pull request.

Will do. I will rebase on master once your PR is in and then send V2.

[...]
diff mbox series

Patch

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 983e235f44..82489bc09c 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -859,6 +859,7 @@  dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
 dtb-$(CONFIG_TARGET_STM32MP1) += \
 	stm32mp157a-dk1.dtb \
 	stm32mp157a-avenger96.dtb \
+	stm32mp157c-dhcom-pdk2-u-boot.dtb \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb
diff --git a/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts b/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
new file mode 100644
index 0000000000..fd99988570
--- /dev/null
+++ b/arch/arm/dts/stm32mp157c-dhcom-pdk2-u-boot.dts
@@ -0,0 +1,7 @@ 
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <marex at denx.de>
+ */
+
+#include "stm32mp157c-dhcom-pdk2.dts"
+#include "stm32mp157c-dhcom-u-boot.dtsi"
diff --git a/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts b/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
new file mode 100644
index 0000000000..05aa545f55
--- /dev/null
+++ b/arch/arm/dts/stm32mp157c-dhcom-pdk2.dts
@@ -0,0 +1,88 @@ 
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <marex at denx.de>
+ */
+
+#include "stm32mp157c-dhcom.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C DHCOM Premium Developer Kit (2)";
+	compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+		ethernet0 = &ethernet0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_pins_sleep_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+	st,eth_ref_clk_sel;
+	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy at 1 {
+			reg = <1>;
+		};
+	};
+};
+
+&pinctrl {
+	ethernet0_rmii_pins_a: rmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, AF0)>,   /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+			bias-disable;
+		};
+	};
+
+	ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 2, ANALOG)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>,  /* ETH1_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+		};
+	};
+};
diff --git a/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi b/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
new file mode 100644
index 0000000000..320912edd8
--- /dev/null
+++ b/arch/arm/dts/stm32mp157c-dhcom-u-boot.dtsi
@@ -0,0 +1,238 @@ 
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <marex at denx.de>
+ */
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp157-u-boot.dtsi"
+#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
+
+/ {
+	aliases {
+		i2c1 = &i2c2;
+		i2c3 = &i2c4;
+		i2c4 = &i2c5;
+		mmc0 = &sdmmc1;
+		mmc1 = &sdmmc2;
+		spi0 = &qspi;
+		usb0 = &usbotg_hs;
+	};
+
+	config {
+		u-boot,boot-led = "heartbeat";
+		u-boot,error-led = "error";
+		st,fastboot-gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+		st,stm32prog-gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+	};
+
+	led {
+		red {
+			label = "error";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			status = "okay";
+		};
+
+		blue {
+			default-state = "on";
+		};
+	};
+};
+
+&i2c4 {
+	u-boot,dm-pre-reloc;
+};
+
+&i2c4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins {
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&pmic {
+	u-boot,dm-pre-reloc;
+};
+
+&flash0 {
+	u-boot,dm-spl;
+};
+
+&qspi {
+	u-boot,dm-spl;
+};
+
+&qspi_clk_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk1_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&qspi_bk2_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&rcc {
+	st,clksrc = <
+		CLK_MPU_PLL1P
+		CLK_AXI_PLL2P
+		CLK_MCU_PLL3P
+		CLK_PLL12_HSE
+		CLK_PLL3_HSE
+		CLK_PLL4_HSE
+		CLK_RTC_LSE
+		CLK_MCO1_DISABLED
+		CLK_MCO2_DISABLED
+	>;
+
+	st,clkdiv = <
+		1 /*MPU*/
+		0 /*AXI*/
+		0 /*MCU*/
+		1 /*APB1*/
+		1 /*APB2*/
+		1 /*APB3*/
+		1 /*APB4*/
+		2 /*APB5*/
+		23 /*RTC*/
+		0 /*MCO1*/
+		0 /*MCO2*/
+	>;
+
+	st,pkcs = <
+		CLK_CKPER_HSE
+		CLK_FMC_ACLK
+		CLK_QSPI_ACLK
+		CLK_ETH_PLL4P
+		CLK_SDMMC12_PLL4P
+		CLK_DSI_DSIPLL
+		CLK_STGEN_HSE
+		CLK_USBPHY_HSE
+		CLK_SPI2S1_PLL3Q
+		CLK_SPI2S23_PLL3Q
+		CLK_SPI45_HSI
+		CLK_SPI6_HSI
+		CLK_I2C46_HSI
+		CLK_SDMMC3_PLL4P
+		CLK_USBO_USBPHY
+		CLK_ADC_CKPER
+		CLK_CEC_LSE
+		CLK_I2C12_HSI
+		CLK_I2C35_HSI
+		CLK_UART1_HSI
+		CLK_UART24_HSI
+		CLK_UART35_HSI
+		CLK_UART6_HSI
+		CLK_UART78_HSI
+		CLK_SPDIF_PLL4P
+		CLK_FDCAN_PLL4Q
+		CLK_SAI1_PLL3Q
+		CLK_SAI2_PLL3Q
+		CLK_SAI3_PLL3Q
+		CLK_SAI4_PLL3Q
+		CLK_RNG1_LSI
+		CLK_RNG2_LSI
+		CLK_LPTIM1_PCLK1
+		CLK_LPTIM23_PCLK3
+		CLK_LPTIM45_LSE
+	>;
+
+	/* VCO = 1300.0 MHz => P = 650 (CPU) */
+	pll1: st,pll at 0 {
+		cfg = < 2 80 0 0 0 PQR(1,0,0) >;
+		frac = < 0x800 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+	pll2: st,pll at 1 {
+		cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+		frac = < 0x1400 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 417.8 MHz => P = 209, Q = 24, R = 11 */
+	pll3: st,pll at 2 {
+		cfg = < 1 33 1 16 36 PQR(1,1,1) >;
+		frac = < 0x1a04 >;
+		u-boot,dm-pre-reloc;
+	};
+
+	/* VCO = 600.0 MHz => P = 50, Q = 50, R = 50 */
+	pll4: st,pll at 3 {
+		cfg = < 1 49 11 11 11 PQR(1,1,1) >;
+		u-boot,dm-pre-reloc;
+	};
+};
+
+&sdmmc1 {
+	u-boot,dm-spl;
+};
+
+&sdmmc1_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc1_dir_pins_a {
+	u-boot,dm-spl;
+	pins1 {
+		u-boot,dm-spl;
+	};
+	pins2 {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2 {
+	u-boot,dm-spl;
+};
+
+&sdmmc2_b4_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&sdmmc2_d47_pins_a {
+	u-boot,dm-spl;
+	pins {
+		u-boot,dm-spl;
+	};
+};
+
+&uart4 {
+	u-boot,dm-pre-reloc;
+};
+
+&uart4_pins_a {
+	u-boot,dm-pre-reloc;
+	pins1 {
+		u-boot,dm-pre-reloc;
+	};
+	pins2 {
+		u-boot,dm-pre-reloc;
+		/* pull-up on rx to avoid floating level */
+		bias-pull-up;
+	};
+};
diff --git a/arch/arm/dts/stm32mp157c-dhcom.dtsi b/arch/arm/dts/stm32mp157c-dhcom.dtsi
new file mode 100644
index 0000000000..96661ae783
--- /dev/null
+++ b/arch/arm/dts/stm32mp157c-dhcom.dtsi
@@ -0,0 +1,379 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2019 Marek Vasut <marex at denx.de>
+ */
+/dts-v1/;
+
+#include "stm32mp157c.dtsi"
+#include "stm32mp157xaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	memory at c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x40000000>;
+	};
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&dcmi {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcmi_pins_a>;
+	pinctrl-1 = <&dcmi_sleep_pins_a>;
+};
+
+&dts {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic at 33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			 bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			 };
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			 };
+
+			 vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge;
+			 };
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+
+	eeprom at 50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	status = "okay";
+};
+
+&pwr {
+	pwr-regulators {
+		vdd-supply = <&vdd>;
+		vdd_3v3_usbfs-supply = <&vdd_usb>;
+	};
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: mx66l51235l at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	flash1: mx66l51235l at 1 {
+		compatible = "jedec,spi-nor";
+		reg = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	broken-cd;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,sig-dir;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	status = "disabled";
+};
+
+&timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 1 {
+		status = "okay";
+	};
+};
+
+&timers6 {
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	timer at 5 {
+		status = "okay";
+	};
+};
+
+&timers8 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm8_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 7 {
+		status = "okay";
+	};
+};
+
+&timers12 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "disabled";
+	pwm {
+		pinctrl-0 = <&pwm12_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer at 11 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/mach-stm32mp/Kconfig b/arch/arm/mach-stm32mp/Kconfig
index ae28f6e206..1aa5f8a122 100644
--- a/arch/arm/mach-stm32mp/Kconfig
+++ b/arch/arm/mach-stm32mp/Kconfig
@@ -147,5 +147,6 @@  config DEBUG_UART_CLOCK
 endif
 
 source "board/st/stm32mp1/Kconfig"
+source "board/dhelectronics/dh_stm32mp1/Kconfig"
 
 endif
diff --git a/board/dhelectronics/dh_stm32mp1/Kconfig b/board/dhelectronics/dh_stm32mp1/Kconfig
new file mode 100644
index 0000000000..e751a3e5ed
--- /dev/null
+++ b/board/dhelectronics/dh_stm32mp1/Kconfig
@@ -0,0 +1,25 @@ 
+config TARGET_DH_STM32MP1_PDK2
+	bool "support of DH STM32MP1 PDK2"
+	default y
+
+if TARGET_DH_STM32MP1_PDK2
+
+config SYS_BOARD
+	default "dh_stm32mp1"
+
+config SYS_VENDOR
+	default "dhelectronics"
+
+config SYS_CONFIG_NAME
+	default "stm32mp1"
+
+config ENV_SECT_SIZE
+	default 0x10000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET
+	default 0x1E0000 if ENV_IS_IN_SPI_FLASH
+
+config ENV_OFFSET_REDUND
+	default 0x1F0000 if ENV_IS_IN_SPI_FLASH
+
+endif
diff --git a/board/dhelectronics/dh_stm32mp1/MAINTAINERS b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
new file mode 100644
index 0000000000..38f54a3da4
--- /dev/null
+++ b/board/dhelectronics/dh_stm32mp1/MAINTAINERS
@@ -0,0 +1,7 @@ 
+DH_STM32MP1_PDK2 BOARD
+M:	Marek Vasut <marex at denx.de>
+S:	Maintained
+F:	arch/arm/dts/stm32mp157c-dhcom*
+F:	board/dhelectronics/dh_stm32mp1/
+F:	configs/stm32mp15_dhcom_basic_defconfig
+F:	include/configs/stm32mp1.h
diff --git a/board/dhelectronics/dh_stm32mp1/Makefile b/board/dhelectronics/dh_stm32mp1/Makefile
new file mode 100644
index 0000000000..a9d28218ef
--- /dev/null
+++ b/board/dhelectronics/dh_stm32mp1/Makefile
@@ -0,0 +1,12 @@ 
+# SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+#
+# Copyright (C) 2018, STMicroelectronics - All Rights Reserved
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y += ../../st/stm32mp1/spl.o
+else
+obj-$(CONFIG_CMD_STBOARD) += ../../st/stm32mp1/cmd_stboard.o
+endif
+
+obj-y += ../../st/stm32mp1/board.o board.o
diff --git a/board/dhelectronics/dh_stm32mp1/board.c b/board/dhelectronics/dh_stm32mp1/board.c
new file mode 100644
index 0000000000..54cc3b7587
--- /dev/null
+++ b/board/dhelectronics/dh_stm32mp1/board.c
@@ -0,0 +1,777 @@ 
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
+ */
+
+#include <common.h>
+#include <adc.h>
+#include <asm/arch/stm32.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <bootm.h>
+#include <clk.h>
+#include <config.h>
+#include <dm.h>
+#include <dm/device.h>
+#include <dm/uclass.h>
+#include <env.h>
+#include <env_internal.h>
+#include <g_dnl.h>
+#include <generic-phy.h>
+#include <i2c.h>
+#include <i2c_eeprom.h>
+#include <init.h>
+#include <led.h>
+#include <memalign.h>
+#include <misc.h>
+#include <mtd.h>
+#include <mtd_node.h>
+#include <netdev.h>
+#include <phy.h>
+#include <power/regulator.h>
+#include <remoteproc.h>
+#include <reset.h>
+#include <syscon.h>
+#include <usb.h>
+#include <usb/dwc2_udc.h>
+#include <watchdog.h>
+
+/* SYSCFG registers */
+#define SYSCFG_BOOTR		0x00
+#define SYSCFG_PMCSETR		0x04
+#define SYSCFG_IOCTRLSETR	0x18
+#define SYSCFG_ICNR		0x1C
+#define SYSCFG_CMPCR		0x20
+#define SYSCFG_CMPENSETR	0x24
+#define SYSCFG_PMCCLRR		0x44
+
+#define SYSCFG_BOOTR_BOOT_MASK		GENMASK(2, 0)
+#define SYSCFG_BOOTR_BOOTPD_SHIFT	4
+
+#define SYSCFG_IOCTRLSETR_HSLVEN_TRACE		BIT(0)
+#define SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI	BIT(1)
+#define SYSCFG_IOCTRLSETR_HSLVEN_ETH		BIT(2)
+#define SYSCFG_IOCTRLSETR_HSLVEN_SDMMC		BIT(3)
+#define SYSCFG_IOCTRLSETR_HSLVEN_SPI		BIT(4)
+
+#define SYSCFG_CMPCR_SW_CTRL		BIT(1)
+#define SYSCFG_CMPCR_READY		BIT(8)
+
+#define SYSCFG_CMPENSETR_MPU_EN		BIT(0)
+
+#define SYSCFG_PMCSETR_ETH_CLK_SEL	BIT(16)
+#define SYSCFG_PMCSETR_ETH_REF_CLK_SEL	BIT(17)
+
+#define SYSCFG_PMCSETR_ETH_SELMII	BIT(20)
+
+#define SYSCFG_PMCSETR_ETH_SEL_MASK	GENMASK(23, 21)
+#define SYSCFG_PMCSETR_ETH_SEL_GMII_MII	0
+#define SYSCFG_PMCSETR_ETH_SEL_RGMII	BIT(21)
+#define SYSCFG_PMCSETR_ETH_SEL_RMII	BIT(23)
+
+/*
+ * Get a global data pointer
+ */
+DECLARE_GLOBAL_DATA_PTR;
+
+int setup_mac_address(void)
+{
+	struct udevice *dev;
+	ofnode eeprom;
+	unsigned char enetaddr[6];
+	int ret;
+
+	ret = eth_env_get_enetaddr("ethaddr", enetaddr);
+	if (ret)	/* ethaddr is already set */
+		return 0;
+
+	eeprom = ofnode_path("/soc/i2c at 5c002000/eeprom at 50");
+	if (!ofnode_valid(eeprom)) {
+		printf("Invalid hardware path to EEPROM!\n");
+		return -ENODEV;
+	}
+
+	ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom, &dev);
+	if (ret) {
+		printf("Cannot find EEPROM!\n");
+		return ret;
+	}
+
+	ret = i2c_eeprom_read(dev, 0xfa, enetaddr, 0x6);
+	if (ret) {
+		printf("Error reading configuration EEPROM!\n");
+		return ret;
+	}
+
+	if (is_valid_ethaddr(enetaddr))
+		eth_env_set_enetaddr("ethaddr", enetaddr);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	int ret;
+	char *mode;
+	u32 otp;
+	struct udevice *dev;
+	const char *fdt_compat;
+	int fdt_compat_len;
+
+	if (IS_ENABLED(CONFIG_STM32MP1_OPTEE))
+		mode = "trusted with OP-TEE";
+	else if (IS_ENABLED(CONFIG_STM32MP1_TRUSTED))
+		mode = "trusted";
+	else
+		mode = "basic";
+
+	printf("Board: stm32mp1 in %s mode", mode);
+	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
+				 &fdt_compat_len);
+	if (fdt_compat && fdt_compat_len)
+		printf(" (%s)", fdt_compat);
+	puts("\n");
+
+	ret = uclass_get_device_by_driver(UCLASS_MISC,
+					  DM_GET_DRIVER(stm32mp_bsec),
+					  &dev);
+
+	if (!ret)
+		ret = misc_read(dev, STM32_BSEC_SHADOW(BSEC_OTP_BOARD),
+				&otp, sizeof(otp));
+	if (ret > 0 && otp) {
+		printf("Board: MB%04x Var%d Rev.%c-%02d\n",
+		       otp >> 16,
+		       (otp >> 12) & 0xF,
+		       ((otp >> 8) & 0xF) - 1 + 'A',
+		       otp & 0xF);
+	}
+
+	return 0;
+}
+
+static void board_key_check(void)
+{
+#if defined(CONFIG_FASTBOOT) || defined(CONFIG_CMD_STM32PROG)
+	ofnode node;
+	struct gpio_desc gpio;
+	enum forced_boot_mode boot_mode = BOOT_NORMAL;
+
+	node = ofnode_path("/config");
+	if (!ofnode_valid(node)) {
+		debug("%s: no /config node?\n", __func__);
+		return;
+	}
+#ifdef CONFIG_FASTBOOT
+	if (gpio_request_by_name_nodev(node, "st,fastboot-gpios", 0,
+				       &gpio, GPIOD_IS_IN)) {
+		debug("%s: could not find a /config/st,fastboot-gpios\n",
+		      __func__);
+	} else {
+		if (dm_gpio_get_value(&gpio)) {
+			puts("Fastboot key pressed, ");
+			boot_mode = BOOT_FASTBOOT;
+		}
+
+		dm_gpio_free(NULL, &gpio);
+	}
+#endif
+#ifdef CONFIG_CMD_STM32PROG
+	if (gpio_request_by_name_nodev(node, "st,stm32prog-gpios", 0,
+				       &gpio, GPIOD_IS_IN)) {
+		debug("%s: could not find a /config/st,stm32prog-gpios\n",
+		      __func__);
+	} else {
+		if (dm_gpio_get_value(&gpio)) {
+			puts("STM32Programmer key pressed, ");
+			boot_mode = BOOT_STM32PROG;
+		}
+		dm_gpio_free(NULL, &gpio);
+	}
+#endif
+
+	if (boot_mode != BOOT_NORMAL) {
+		puts("entering download mode...\n");
+		clrsetbits_le32(TAMP_BOOT_CONTEXT,
+				TAMP_BOOT_FORCED_MASK,
+				boot_mode);
+	}
+#endif
+}
+
+#if defined(CONFIG_USB_GADGET) && defined(CONFIG_USB_GADGET_DWC2_OTG)
+
+/* STMicroelectronics STUSB1600 Type-C controller */
+#define STUSB1600_CC_CONNECTION_STATUS		0x0E
+
+/* STUSB1600_CC_CONNECTION_STATUS bitfields */
+#define STUSB1600_CC_ATTACH			BIT(0)
+
+static int stusb1600_init(struct udevice **dev_stusb1600)
+{
+	ofnode node;
+	struct udevice *dev, *bus;
+	int ret;
+	u32 chip_addr;
+
+	*dev_stusb1600 = NULL;
+
+	/* if node stusb1600 is present, means DK1 or DK2 board */
+	node = ofnode_by_compatible(ofnode_null(), "st,stusb1600");
+	if (!ofnode_valid(node))
+		return -ENODEV;
+
+	ret = ofnode_read_u32(node, "reg", &chip_addr);
+	if (ret)
+		return -EINVAL;
+
+	ret = uclass_get_device_by_ofnode(UCLASS_I2C, ofnode_get_parent(node),
+					  &bus);
+	if (ret) {
+		printf("bus for stusb1600 not found\n");
+		return -ENODEV;
+	}
+
+	ret = dm_i2c_probe(bus, chip_addr, 0, &dev);
+	if (!ret)
+		*dev_stusb1600 = dev;
+
+	return ret;
+}
+
+static int stusb1600_cable_connected(struct udevice *dev)
+{
+	u8 status;
+
+	if (dm_i2c_read(dev, STUSB1600_CC_CONNECTION_STATUS, &status, 1))
+		return 0;
+
+	return status & STUSB1600_CC_ATTACH;
+}
+
+#include <usb/dwc2_udc.h>
+int g_dnl_board_usb_cable_connected(void)
+{
+	struct udevice *stusb1600;
+	struct udevice *dwc2_udc_otg;
+	int ret;
+
+	if (!stusb1600_init(&stusb1600))
+		return stusb1600_cable_connected(stusb1600);
+
+	ret = uclass_get_device_by_driver(UCLASS_USB_GADGET_GENERIC,
+					  DM_GET_DRIVER(dwc2_udc_otg),
+					  &dwc2_udc_otg);
+	if (!ret)
+		debug("dwc2_udc_otg init failed\n");
+
+	return dwc2_udc_B_session_valid(dwc2_udc_otg);
+}
+
+#define STM32MP1_G_DNL_DFU_PRODUCT_NUM 0xdf11
+#define STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM 0x0afb
+
+int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char *name)
+{
+	if (!strcmp(name, "usb_dnl_dfu"))
+		put_unaligned(STM32MP1_G_DNL_DFU_PRODUCT_NUM, &dev->idProduct);
+	else if (!strcmp(name, "usb_dnl_fastboot"))
+		put_unaligned(STM32MP1_G_DNL_FASTBOOT_PRODUCT_NUM,
+			      &dev->idProduct);
+	else
+		put_unaligned(CONFIG_USB_GADGET_PRODUCT_NUM, &dev->idProduct);
+
+	return 0;
+}
+
+#endif /* CONFIG_USB_GADGET */
+
+#ifdef CONFIG_LED
+static int get_led(struct udevice **dev, char *led_string)
+{
+	char *led_name;
+	int ret;
+
+	led_name = fdtdec_get_config_string(gd->fdt_blob, led_string);
+	if (!led_name) {
+		pr_debug("%s: could not find %s config string\n",
+			 __func__, led_string);
+		return -ENOENT;
+	}
+	ret = led_get_by_label(led_name, dev);
+	if (ret) {
+		debug("%s: get=%d\n", __func__, ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int setup_led(enum led_state_t cmd)
+{
+	struct udevice *dev;
+	int ret;
+
+	ret = get_led(&dev, "u-boot,boot-led");
+	if (ret)
+		return ret;
+
+	ret = led_set_state(dev, cmd);
+	return ret;
+}
+#endif
+
+static void __maybe_unused led_error_blink(u32 nb_blink)
+{
+#ifdef CONFIG_LED
+	int ret;
+	struct udevice *led;
+	u32 i;
+#endif
+
+	if (!nb_blink)
+		return;
+
+#ifdef CONFIG_LED
+	ret = get_led(&led, "u-boot,error-led");
+	if (!ret) {
+		/* make u-boot,error-led blinking */
+		/* if U32_MAX and 125ms interval, for 17.02 years */
+		for (i = 0; i < 2 * nb_blink; i++) {
+			led_set_state(led, LEDST_TOGGLE);
+			mdelay(125);
+			WATCHDOG_RESET();
+		}
+	}
+#endif
+
+	/* infinite: the boot process must be stopped */
+	if (nb_blink == U32_MAX)
+		hang();
+}
+
+static void sysconf_init(void)
+{
+#ifndef CONFIG_STM32MP1_TRUSTED
+	u8 *syscfg;
+#ifdef CONFIG_DM_REGULATOR
+	struct udevice *pwr_dev;
+	struct udevice *pwr_reg;
+	struct udevice *dev;
+	int ret;
+	u32 otp = 0;
+#endif
+	u32 bootr;
+
+	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
+
+	/* interconnect update : select master using the port 1 */
+	/* LTDC = AXI_M9 */
+	/* GPU  = AXI_M8 */
+	/* today information is hardcoded in U-Boot */
+	writel(BIT(9), syscfg + SYSCFG_ICNR);
+
+	/* disable Pull-Down for boot pin connected to VDD */
+	bootr = readl(syscfg + SYSCFG_BOOTR);
+	bootr &= ~(SYSCFG_BOOTR_BOOT_MASK << SYSCFG_BOOTR_BOOTPD_SHIFT);
+	bootr |= (bootr & SYSCFG_BOOTR_BOOT_MASK) << SYSCFG_BOOTR_BOOTPD_SHIFT;
+	writel(bootr, syscfg + SYSCFG_BOOTR);
+
+#ifdef CONFIG_DM_REGULATOR
+	/* High Speed Low Voltage Pad mode Enable for SPI, SDMMC, ETH, QSPI
+	 * and TRACE. Needed above ~50MHz and conditioned by AFMUX selection.
+	 * The customer will have to disable this for low frequencies
+	 * or if AFMUX is selected but the function not used, typically for
+	 * TRACE. Otherwise, impact on power consumption.
+	 *
+	 * WARNING:
+	 *   enabling High Speed mode while VDD>2.7V
+	 *   with the OTP product_below_2v5 (OTP 18, BIT 13)
+	 *   erroneously set to 1 can damage the IC!
+	 *   => U-Boot set the register only if VDD < 2.7V (in DT)
+	 *      but this value need to be consistent with board design
+	 */
+	ret = uclass_get_device_by_driver(UCLASS_PMIC,
+					  DM_GET_DRIVER(stm32mp_pwr_pmic),
+					  &pwr_dev);
+	if (!ret) {
+		ret = uclass_get_device_by_driver(UCLASS_MISC,
+						  DM_GET_DRIVER(stm32mp_bsec),
+						  &dev);
+		if (ret) {
+			pr_err("Can't find stm32mp_bsec driver\n");
+			return;
+		}
+
+		ret = misc_read(dev, STM32_BSEC_SHADOW(18), &otp, 4);
+		if (ret > 0)
+			otp = otp & BIT(13);
+
+		/* get VDD = vdd-supply */
+		ret = device_get_supply_regulator(pwr_dev, "vdd-supply",
+						  &pwr_reg);
+
+		/* check if VDD is Low Voltage */
+		if (!ret) {
+			if (regulator_get_value(pwr_reg) < 2700000) {
+				writel(SYSCFG_IOCTRLSETR_HSLVEN_TRACE |
+				       SYSCFG_IOCTRLSETR_HSLVEN_QUADSPI |
+				       SYSCFG_IOCTRLSETR_HSLVEN_ETH |
+				       SYSCFG_IOCTRLSETR_HSLVEN_SDMMC |
+				       SYSCFG_IOCTRLSETR_HSLVEN_SPI,
+				       syscfg + SYSCFG_IOCTRLSETR);
+
+				if (!otp)
+					pr_err("product_below_2v5=0: HSLVEN protected by HW\n");
+			} else {
+				if (otp)
+					pr_err("product_below_2v5=1: HSLVEN update is destructive, no update as VDD>2.7V\n");
+			}
+		} else {
+			debug("VDD unknown");
+		}
+	}
+#endif
+
+	/* activate automatic I/O compensation
+	 * warning: need to ensure CSI enabled and ready in clock driver
+	 */
+	writel(SYSCFG_CMPENSETR_MPU_EN, syscfg + SYSCFG_CMPENSETR);
+
+	while (!(readl(syscfg + SYSCFG_CMPCR) & SYSCFG_CMPCR_READY))
+		;
+	clrbits_le32(syscfg + SYSCFG_CMPCR, SYSCFG_CMPCR_SW_CTRL);
+#endif
+}
+
+/* board dependent setup after realloc */
+int board_init(void)
+{
+	struct udevice *dev;
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = STM32_DDR_BASE + 0x100;
+
+	/* probe all PINCTRL for hog */
+	for (uclass_first_device(UCLASS_PINCTRL, &dev);
+	     dev;
+	     uclass_next_device(&dev)) {
+		pr_debug("probe pincontrol = %s\n", dev->name);
+	}
+
+	board_key_check();
+
+#ifdef CONFIG_DM_REGULATOR
+	regulators_enable_boot_on(_DEBUG);
+#endif
+
+	sysconf_init();
+
+	if (CONFIG_IS_ENABLED(CONFIG_LED))
+		led_default_state();
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	char *boot_device;
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	const void *fdt_compat;
+	int fdt_compat_len;
+	int ret;
+	u32 otp;
+	struct udevice *dev;
+	char buf[10];
+
+	fdt_compat = fdt_getprop(gd->fdt_blob, 0, "compatible",
+				 &fdt_compat_len);
+	if (fdt_compat && fdt_compat_len) {
+		if (strncmp(fdt_compat, "st,", 3) != 0)
+			env_set("board_name", fdt_compat);
+		else
+			env_set("board_name", fdt_compat + 3);
+	}
+	ret = uclass_get_device_by_driver(UCLASS_MISC,
+					  DM_GET_DRIVER(stm32mp_bsec),
+					  &dev);
+
+	if (!ret)
+		ret = misc_read(dev, STM32_BSEC_SHADOW(BSEC_OTP_BOARD),
+				&otp, sizeof(otp));
+	if (!ret && otp) {
+		snprintf(buf, sizeof(buf), "0x%04x", otp >> 16);
+		env_set("board_id", buf);
+
+		snprintf(buf, sizeof(buf), "0x%04x",
+			 ((otp >> 8) & 0xF) - 1 + 0xA);
+		env_set("board_rev", buf);
+	}
+#endif
+
+	/* Check the boot-source to disable bootdelay */
+	boot_device = env_get("boot_device");
+	if (!strcmp(boot_device, "serial") || !strcmp(boot_device, "usb"))
+		env_set("bootdelay", "0");
+
+	return 0;
+}
+
+void board_quiesce_devices(void)
+{
+#ifdef CONFIG_LED
+	setup_led(LEDST_OFF);
+#endif
+}
+
+/* eth init function : weak called in eqos driver */
+int board_interface_eth_init(struct udevice *dev,
+			     phy_interface_t interface_type)
+{
+	u8 *syscfg;
+	u32 value;
+	bool eth_clk_sel_reg = false;
+	bool eth_ref_clk_sel_reg = false;
+
+	/* Gigabit Ethernet 125MHz clock selection. */
+	eth_clk_sel_reg = dev_read_bool(dev, "st,eth_clk_sel");
+
+	/* Ethernet 50Mhz RMII clock selection */
+	eth_ref_clk_sel_reg =
+		dev_read_bool(dev, "st,eth_ref_clk_sel");
+
+	syscfg = (u8 *)syscon_get_first_range(STM32MP_SYSCON_SYSCFG);
+
+	if (!syscfg)
+		return -ENODEV;
+
+	switch (interface_type) {
+	case PHY_INTERFACE_MODE_MII:
+		value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
+			SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
+		debug("%s: PHY_INTERFACE_MODE_MII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_GMII:
+		if (eth_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII |
+				SYSCFG_PMCSETR_ETH_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_GMII_MII;
+		debug("%s: PHY_INTERFACE_MODE_GMII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		if (eth_ref_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_RMII |
+				SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_RMII;
+		debug("%s: PHY_INTERFACE_MODE_RMII\n", __func__);
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		if (eth_clk_sel_reg)
+			value = SYSCFG_PMCSETR_ETH_SEL_RGMII |
+				SYSCFG_PMCSETR_ETH_CLK_SEL;
+		else
+			value = SYSCFG_PMCSETR_ETH_SEL_RGMII;
+		debug("%s: PHY_INTERFACE_MODE_RGMII\n", __func__);
+		break;
+	default:
+		debug("%s: Do not manage %d interface\n",
+		      __func__, interface_type);
+		/* Do not manage others interfaces */
+		return -EINVAL;
+	}
+
+	/* clear and set ETH configuration bits */
+	writel(SYSCFG_PMCSETR_ETH_SEL_MASK | SYSCFG_PMCSETR_ETH_SELMII |
+	       SYSCFG_PMCSETR_ETH_REF_CLK_SEL | SYSCFG_PMCSETR_ETH_CLK_SEL,
+	       syscfg + SYSCFG_PMCCLRR);
+	writel(value, syscfg + SYSCFG_PMCSETR);
+
+	return 0;
+}
+
+enum env_location env_get_location(enum env_operation op, int prio)
+{
+	if (prio)
+		return ENVL_UNKNOWN;
+
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
+	return ENVL_SPI_FLASH;
+#else
+	return ENVL_NOWHERE;
+#endif
+}
+
+#ifdef CONFIG_SYS_MTDPARTS_RUNTIME
+
+#define MTDPARTS_LEN		256
+#define MTDIDS_LEN		128
+
+/**
+ * The mtdparts_nand0 and mtdparts_nor0 variable tends to be long.
+ * If we need to access it before the env is relocated, then we need
+ * to use our own stack buffer. gd->env_buf will be too small.
+ *
+ * @param buf temporary buffer pointer MTDPARTS_LEN long
+ * @return mtdparts variable string, NULL if not found
+ */
+static const char *env_get_mtdparts(const char *str, char *buf)
+{
+	if (gd->flags & GD_FLG_ENV_READY)
+		return env_get(str);
+	if (env_get_f(str, buf, MTDPARTS_LEN) != -1)
+		return buf;
+
+	return NULL;
+}
+
+/**
+ * update the variables "mtdids" and "mtdparts" with content of mtdparts_<dev>
+ */
+static void board_get_mtdparts(const char *dev,
+			       char *mtdids,
+			       char *mtdparts)
+{
+	char env_name[32] = "mtdparts_";
+	char tmp_mtdparts[MTDPARTS_LEN];
+	const char *tmp;
+
+	/* name of env variable to read = mtdparts_<dev> */
+	strcat(env_name, dev);
+	tmp = env_get_mtdparts(env_name, tmp_mtdparts);
+	if (tmp) {
+		/* mtdids: "<dev>=<dev>, ...." */
+		if (mtdids[0] != '\0')
+			strcat(mtdids, ",");
+		strcat(mtdids, dev);
+		strcat(mtdids, "=");
+		strcat(mtdids, dev);
+
+		/* mtdparts: "mtdparts=<dev>:<mtdparts_<dev>>;..." */
+		if (mtdparts[0] != '\0')
+			strncat(mtdparts, ";", MTDPARTS_LEN);
+		else
+			strcat(mtdparts, "mtdparts=");
+		strncat(mtdparts, dev, MTDPARTS_LEN);
+		strncat(mtdparts, ":", MTDPARTS_LEN);
+		strncat(mtdparts, tmp, MTDPARTS_LEN);
+	}
+}
+
+void board_mtdparts_default(const char **mtdids, const char **mtdparts)
+{
+	struct udevice *dev;
+	static char parts[3 * MTDPARTS_LEN + 1];
+	static char ids[MTDIDS_LEN + 1];
+	static bool mtd_initialized;
+
+	if (mtd_initialized) {
+		*mtdids = ids;
+		*mtdparts = parts;
+		return;
+	}
+
+	memset(parts, 0, sizeof(parts));
+	memset(ids, 0, sizeof(ids));
+
+	/* probe all MTD devices */
+	for (uclass_first_device(UCLASS_MTD, &dev);
+	     dev;
+	     uclass_next_device(&dev)) {
+		pr_debug("mtd device = %s\n", dev->name);
+	}
+
+	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
+		board_get_mtdparts("nor0", ids, parts);
+
+	mtd_initialized = true;
+	*mtdids = ids;
+	*mtdparts = parts;
+	debug("%s:mtdids=%s & mtdparts=%s\n", __func__, ids, parts);
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+int ft_board_setup(void *blob, bd_t *bd)
+{
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_SET_DFU_ALT_INFO
+#define DFU_ALT_BUF_LEN SZ_1K
+
+static void board_get_alt_info(const char *dev, char *buff)
+{
+	char var_name[32] = "dfu_alt_info_";
+	int ret;
+
+	ALLOC_CACHE_ALIGN_BUFFER(char, tmp_alt, DFU_ALT_BUF_LEN);
+
+	/* name of env variable to read = dfu_alt_info_<dev> */
+	strcat(var_name, dev);
+	ret = env_get_f(var_name, tmp_alt, DFU_ALT_BUF_LEN);
+	if (ret) {
+		if (buff[0] != '\0')
+			strcat(buff, "&");
+		strncat(buff, tmp_alt, DFU_ALT_BUF_LEN);
+	}
+}
+
+void set_dfu_alt_info(char *interface, char *devstr)
+{
+	struct udevice *dev;
+
+	ALLOC_CACHE_ALIGN_BUFFER(char, buf, DFU_ALT_BUF_LEN);
+
+	if (env_get("dfu_alt_info"))
+		return;
+
+	memset(buf, 0, sizeof(buf));
+
+	/* probe all MTD devices */
+	mtd_probe_devices();
+
+	board_get_alt_info("ram", buf);
+
+	if (!uclass_get_device(UCLASS_MMC, 0, &dev))
+		board_get_alt_info("mmc0", buf);
+
+	if (!uclass_get_device(UCLASS_MMC, 1, &dev))
+		board_get_alt_info("mmc1", buf);
+
+	if (!uclass_get_device(UCLASS_SPI_FLASH, 0, &dev))
+		board_get_alt_info("nor0", buf);
+
+	env_set("dfu_alt_info", buf);
+	puts("DFU alt info setting: done\n");
+}
+#endif
+
+static void board_copro_image_process(ulong fw_image, size_t fw_size)
+{
+	int ret, id = 0; /* Copro id fixed to 0 as only one coproc on mp1 */
+
+	if (!rproc_is_initialized())
+		if (rproc_init()) {
+			printf("Remote Processor %d initialization failed\n",
+			       id);
+			return;
+		}
+
+	ret = rproc_load(id, fw_image, fw_size);
+	printf("Load Remote Processor %d with data at addr=0x%08lx %u bytes:%s\n",
+	       id, fw_image, fw_size, ret ? " Failed!" : " Success!");
+
+	if (!ret) {
+		rproc_start(id);
+		env_set("copro_state", "booted");
+	}
+}
+
+U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_COPRO, board_copro_image_process);
diff --git a/configs/stm32mp15_dhcom_basic_defconfig b/configs/stm32mp15_dhcom_basic_defconfig
new file mode 100644
index 0000000000..e4f331a913
--- /dev/null
+++ b/configs/stm32mp15_dhcom_basic_defconfig
@@ -0,0 +1,140 @@ 
+CONFIG_ARM=y
+CONFIG_ARCH_STM32MP=y
+CONFIG_SYS_MALLOC_F_LEN=0x3000
+CONFIG_SPL_MMC_SUPPORT=y
+CONFIG_ENV_SIZE=0x4000
+CONFIG_SPL=y
+CONFIG_TARGET_STM32MP1=y
+# CONFIG_TARGET_STM32MP157C_DK2 is not set
+CONFIG_SPL_SPI_FLASH_SUPPORT=y
+CONFIG_SPL_SPI_SUPPORT=y
+# CONFIG_ARMV7_VIRT is not set
+CONFIG_SPL_TEXT_BASE=0x2FFC2500
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_FIT=y
+# CONFIG_BOOTSTAGE is not set
+CONFIG_BOOTCOMMAND="run bootcmd_stm32mp"
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION=3
+CONFIG_SPL_I2C_SUPPORT=y
+CONFIG_SPL_MTD_SUPPORT=y
+CONFIG_SPL_POWER_SUPPORT=y
+CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
+CONFIG_SYS_PROMPT="STM32MP> "
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_EXPORTENV is not set
+CONFIG_CMD_EEPROM=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_ADC=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_DFU=y
+CONFIG_CMD_FUSE=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MTD=y
+CONFIG_CMD_REMOTEPROC=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_BMP=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_PMIC=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_MTDPARTS=y
+# CONFIG_SPL_DOS_PARTITION is not set
+CONFIG_DEFAULT_DEVICE_TREE="stm32mp157c-dhcom-pdk2-u-boot"
+CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-names interrupts-extended interrupt-controller \\\#interrupt-cells interrupt-parent dmas dma-names assigned-clocks assigned-clock-rates assigned-clock-parents hwlocks"
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_USE_ENV_SPI_BUS=y
+CONFIG_ENV_SPI_BUS=0
+CONFIG_USE_ENV_SPI_CS=y
+CONFIG_ENV_SPI_CS=0
+CONFIG_USE_ENV_SPI_MAX_HZ=y
+CONFIG_ENV_SPI_MAX_HZ=10000000
+CONFIG_USE_ENV_SPI_MODE=y
+CONFIG_ENV_SPI_MODE=0x0
+CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_IP_DEFRAG=y
+CONFIG_TFTP_BLOCKSIZE=1536
+CONFIG_STM32_ADC=y
+CONFIG_SPL_BLOCK_CACHE=y
+CONFIG_DFU_MMC=y
+CONFIG_DFU_RAM=y
+CONFIG_DFU_VIRT=y
+CONFIG_DM_HWSPINLOCK=y
+CONFIG_HWSPINLOCK_STM32=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_STM32F7=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_DM_MAILBOX=y
+CONFIG_STM32_IPCC=y
+CONFIG_I2C_EEPROM=y
+CONFIG_DM_MMC=y
+CONFIG_SUPPORT_EMMC_BOOT=y
+CONFIG_STM32_SDMMC2=y
+CONFIG_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_SPI_FLASH_WINBOND=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_SPI_FLASH_MTD=y
+CONFIG_SPL_SPI_FLASH_MTD=y
+CONFIG_DM_ETH=y
+CONFIG_DWC_ETH_QOS=y
+CONFIG_PHY=y
+CONFIG_PHY_STM32_USBPHYC=y
+CONFIG_PINCONF=y
+# CONFIG_SPL_PINCTRL_FULL is not set
+CONFIG_PINCTRL_STMFX=y
+CONFIG_DM_PMIC=y
+# CONFIG_SPL_PMIC_CHILDREN is not set
+CONFIG_PMIC_STPMIC1=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_REGULATOR_STM32_VREFBUF=y
+CONFIG_DM_REGULATOR_STPMIC1=y
+CONFIG_REMOTEPROC_STM32_COPRO=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_STM32=y
+CONFIG_SERIAL_RX_BUFFER=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_STM32_QSPI=y
+CONFIG_STM32_SPI=y
+CONFIG_USB=y
+CONFIG_DM_USB=y
+CONFIG_DM_USB_GADGET=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="dh"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0483
+CONFIG_USB_GADGET_PRODUCT_NUM=0x5720
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_DM_VIDEO=y
+CONFIG_BACKLIGHT_GPIO=y
+CONFIG_VIDEO_LCD_ORISETECH_OTM8009A=y
+CONFIG_VIDEO_LCD_RAYDIUM_RM68200=y
+CONFIG_VIDEO_STM32=y
+CONFIG_VIDEO_STM32_DSI=y
+CONFIG_VIDEO_STM32_MAX_XRES=1280
+CONFIG_VIDEO_STM32_MAX_YRES=800
+CONFIG_LZO=y
+CONFIG_FDT_FIXUP_PARTITIONS=y