| Message ID | 20231103-b4-qcom-clk-v3-7-8d2d460ece84@linaro.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm: mach-snapdragon: Qualcomm clock driver cleanup | expand |
On Fri, 3 Nov 2023 at 21:11, Caleb Connolly <caleb.connolly@linaro.org> wrote: > > The RCG divider field takes a value of (2*h - 1) where h is the divisor. > This allows fractional dividers to be supported by calculating them at > compile time using a macro. > > However, the clk_rcg_set_rate_mnd() function was also performing the > calculation. Clean this all up and consistently use the F() macro to > calculate these at compile time and properly support fractional divisors. > > Additionally, improve clk_bcr_update() to timeout with a warning rather > than hanging the board, and make the freq_tbl struct and helpers common > so that they can be reused by future platforms. > > Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> > --- > drivers/clk/qcom/clock-apq8016.c | 2 +- > drivers/clk/qcom/clock-apq8096.c | 2 +- > drivers/clk/qcom/clock-qcom.c | 64 +++++++++++++++++++++++++++++----------- > drivers/clk/qcom/clock-qcom.h | 11 +++++++ > drivers/clk/qcom/clock-qcs404.c | 16 +++++----- > drivers/clk/qcom/clock-sdm845.c | 26 ---------------- > 6 files changed, 67 insertions(+), 54 deletions(-) > Reviewed-by: Sumit Garg <sumit.garg@linaro.org> -Sumit > diff --git a/drivers/clk/qcom/clock-apq8016.c b/drivers/clk/qcom/clock-apq8016.c > index 630619c83454..eb812934cbae 100644 > --- a/drivers/clk/qcom/clock-apq8016.c > +++ b/drivers/clk/qcom/clock-apq8016.c > @@ -78,7 +78,7 @@ static struct vote_clk gcc_blsp1_ahb_clk = { > /* SDHCI */ > static int clk_init_sdc(struct msm_clk_priv *priv, int slot, uint rate) > { > - int div = 8; /* 100MHz default */ > + int div = 15; /* 100MHz default */ > > if (rate == 200000000) > div = 4; > diff --git a/drivers/clk/qcom/clock-apq8096.c b/drivers/clk/qcom/clock-apq8096.c > index 095c1b431245..55f16c14e046 100644 > --- a/drivers/clk/qcom/clock-apq8096.c > +++ b/drivers/clk/qcom/clock-apq8096.c > @@ -65,7 +65,7 @@ static struct vote_clk gcc_blsp2_ahb_clk = { > > static int clk_init_sdc(struct msm_clk_priv *priv, uint rate) > { > - int div = 3; > + int div = 5; > > clk_enable_cbc(priv->base + SDCC2_AHB_CBCR); > clk_rcg_set_rate_mnd(priv->base, &sdc_regs, div, 0, 0, > diff --git a/drivers/clk/qcom/clock-qcom.c b/drivers/clk/qcom/clock-qcom.c > index fc478554f982..7c683e519226 100644 > --- a/drivers/clk/qcom/clock-qcom.c > +++ b/drivers/clk/qcom/clock-qcom.c > @@ -19,6 +19,8 @@ > #include <dm/lists.h> > #include <errno.h> > #include <asm/io.h> > +#include <linux/bug.h> > +#include <linux/delay.h> > #include <linux/bitops.h> > #include <reset-uclass.h> > > @@ -68,30 +70,42 @@ void clk_enable_vote_clk(phys_addr_t base, const struct vote_clk *vclk) > /* Update clock command via CMD_RCGR */ > void clk_bcr_update(phys_addr_t apps_cmd_rcgr) > { > + u32 count; > setbits_le32(apps_cmd_rcgr, APPS_CMD_RCGR_UPDATE); > > /* Wait for frequency to be updated. */ > - while (readl(apps_cmd_rcgr) & APPS_CMD_RCGR_UPDATE) > - ; > + for (count = 0; count < 50000; count++) { > + if (!(readl(apps_cmd_rcgr) & APPS_CMD_RCGR_UPDATE)) > + break; > + udelay(1); > + } > + WARN(count == 50000, "WARNING: RCG @ %#llx [%#010x] stuck at off\n", > + apps_cmd_rcgr, readl(apps_cmd_rcgr)); > } > > -#define CFG_MODE_DUAL_EDGE (0x2 << 12) /* Counter mode */ > +#define CFG_SRC_DIV_MASK 0b11111 > +#define CFG_SRC_SEL_SHIFT 8 > +#define CFG_SRC_SEL_MASK (0x7 << CFG_SRC_SEL_SHIFT) > +#define CFG_MODE_SHIFT 12 > +#define CFG_MODE_MASK (0x3 << CFG_MODE_SHIFT) > +#define CFG_MODE_DUAL_EDGE (0x2 << CFG_MODE_SHIFT) > +#define CFG_HW_CLK_CTRL_MASK BIT(20) > > -#define CFG_MASK 0x3FFF > - > -#define CFG_DIVIDER_MASK 0x1F > - > -/* root set rate for clocks with half integer and MND divider */ > +/* > + * root set rate for clocks with half integer and MND divider > + * div should be pre-calculated ((div * 2) - 1) > + */ > void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs, > int div, int m, int n, int source, u8 mnd_width) > { > u32 cfg; > /* M value for MND divider. */ > u32 m_val = m; > + u32 n_minus_m = n - m; > /* NOT(N-M) value for MND divider. */ > - u32 n_val = ~((n) - (m)) * !!(n); > + u32 n_val = ~n_minus_m * !!(n); > /* NOT 2D value for MND divider. */ > - u32 d_val = ~(n); > + u32 d_val = ~(clamp_t(u32, n, m, n_minus_m)); > u32 mask = BIT(mnd_width) - 1; > > debug("m %#x n %#x d %#x div %#x mask %#x\n", m_val, n_val, d_val, div, mask); > @@ -103,15 +117,13 @@ void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs, > > /* setup src select and divider */ > cfg = readl(base + regs->cfg_rcgr); > - cfg &= ~CFG_MASK; > - cfg |= source & CFG_CLK_SRC_MASK; /* Select clock source */ > + cfg &= ~(CFG_SRC_SEL_MASK | CFG_MODE_MASK | CFG_HW_CLK_CTRL_MASK); > + cfg |= source & CFG_SRC_SEL_MASK; /* Select clock source */ > > - /* Set the divider; HW permits fraction dividers (+0.5), but > - for simplicity, we will support integers only */ > if (div) > - cfg |= (2 * div - 1) & CFG_DIVIDER_MASK; > + cfg |= div & CFG_SRC_DIV_MASK; > > - if (n_val) > + if (n && n != m) > cfg |= CFG_MODE_DUAL_EDGE; > > writel(cfg, base + regs->cfg_rcgr); /* Write new clock configuration */ > @@ -128,7 +140,7 @@ void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div, > > /* setup src select and divider */ > cfg = readl(base + regs->cfg_rcgr); > - cfg &= ~CFG_MASK; > + cfg &= ~(CFG_SRC_SEL_MASK | CFG_MODE_MASK | CFG_HW_CLK_CTRL_MASK); > cfg |= source & CFG_CLK_SRC_MASK; /* Select clock source */ > > /* > @@ -136,7 +148,7 @@ void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div, > * for simplicity, we will support integers only > */ > if (div) > - cfg |= (2 * div - 1) & CFG_DIVIDER_MASK; > + cfg |= (2 * div - 1) & CFG_SRC_DIV_MASK; > > writel(cfg, base + regs->cfg_rcgr); /* Write new clock configuration */ > > @@ -144,6 +156,22 @@ void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div, > clk_bcr_update(base + regs->cmd_rcgr); > } > > +const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, uint rate) > +{ > + if (!f) > + return NULL; > + > + if (!f->freq) > + return f; > + > + for (; f->freq; f++) > + if (rate <= f->freq) > + return f; > + > + /* Default to our fastest rate */ > + return f - 1; > +} > + > static int msm_clk_probe(struct udevice *dev) > { > struct msm_clk_data *data = (struct msm_clk_data *)dev_get_driver_data(dev); > diff --git a/drivers/clk/qcom/clock-qcom.h b/drivers/clk/qcom/clock-qcom.h > index 24a32cb9666d..01088c19015a 100644 > --- a/drivers/clk/qcom/clock-qcom.h > +++ b/drivers/clk/qcom/clock-qcom.h > @@ -32,6 +32,16 @@ struct bcr_regs { > uintptr_t D; > }; > > +struct freq_tbl { > + uint freq; > + uint src; > + u8 pre_div; > + u16 m; > + u16 n; > +}; > + > +#define F(f, s, h, m, n) { (f), (s), (2 * (h) - 1), (m), (n) } > + > struct gate_clk { > uintptr_t reg; > u32 en_val; > @@ -71,6 +81,7 @@ void clk_enable_gpll0(phys_addr_t base, const struct pll_vote_clk *gpll0); > void clk_bcr_update(phys_addr_t apps_cmd_rgcr); > void clk_enable_cbc(phys_addr_t cbcr); > void clk_enable_vote_clk(phys_addr_t base, const struct vote_clk *vclk); > +const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, uint rate); > void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs, > int div, int m, int n, int source, u8 mnd_width); > void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div, > diff --git a/drivers/clk/qcom/clock-qcs404.c b/drivers/clk/qcom/clock-qcs404.c > index 921abf1f699b..429ff35e1d1a 100644 > --- a/drivers/clk/qcom/clock-qcs404.c > +++ b/drivers/clk/qcom/clock-qcs404.c > @@ -203,7 +203,7 @@ static ulong qcs404_clk_set_rate(struct clk *clk, ulong rate) > break; > case GCC_SDCC1_APPS_CLK: > /* SDCC1: 200MHz */ > - clk_rcg_set_rate_mnd(priv->base, &sdc_regs, 4, 0, 0, > + clk_rcg_set_rate_mnd(priv->base, &sdc_regs, 7, 0, 0, > CFG_CLK_SRC_GPLL0, 8); > clk_enable_gpll0(priv->base, &gpll0_vote_clk); > clk_enable_cbc(priv->base + SDCC_APPS_CBCR(1)); > @@ -213,16 +213,16 @@ static ulong qcs404_clk_set_rate(struct clk *clk, ulong rate) > break; > case GCC_ETH_RGMII_CLK: > if (rate == 250000000) > - clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 0, 0, > + clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 0, 0, > CFG_CLK_SRC_GPLL1, 8); > else if (rate == 125000000) > - clk_rcg_set_rate_mnd(priv->base, &emac_regs, 4, 0, 0, > + clk_rcg_set_rate_mnd(priv->base, &emac_regs, 7, 0, 0, > CFG_CLK_SRC_GPLL1, 8); > else if (rate == 50000000) > - clk_rcg_set_rate_mnd(priv->base, &emac_regs, 10, 0, 0, > + clk_rcg_set_rate_mnd(priv->base, &emac_regs, 19, 0, 0, > CFG_CLK_SRC_GPLL1, 8); > else if (rate == 5000000) > - clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 1, 50, > + clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 1, 50, > CFG_CLK_SRC_GPLL1, 8); > break; > default: > @@ -239,7 +239,7 @@ static int qcs404_clk_enable(struct clk *clk) > switch (clk->id) { > case GCC_USB30_MASTER_CLK: > clk_enable_cbc(priv->base + USB30_MASTER_CBCR); > - clk_rcg_set_rate_mnd(priv->base, &usb30_master_regs, 4, 0, 0, > + clk_rcg_set_rate_mnd(priv->base, &usb30_master_regs, 7, 0, 0, > CFG_CLK_SRC_GPLL0, 8); > break; > case GCC_SYS_NOC_USB3_CLK: > @@ -261,14 +261,14 @@ static int qcs404_clk_enable(struct clk *clk) > /* SPEED_1000: freq -> 250MHz */ > clk_enable_cbc(priv->base + ETH_PTP_CBCR); > clk_enable_gpll0(priv->base, &gpll1_vote_clk); > - clk_rcg_set_rate_mnd(priv->base, &emac_ptp_regs, 2, 0, 0, > + clk_rcg_set_rate_mnd(priv->base, &emac_ptp_regs, 3, 0, 0, > CFG_CLK_SRC_GPLL1, 8); > break; > case GCC_ETH_RGMII_CLK: > /* SPEED_1000: freq -> 250MHz */ > clk_enable_cbc(priv->base + ETH_RGMII_CBCR); > clk_enable_gpll0(priv->base, &gpll1_vote_clk); > - clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 0, 0, > + clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 0, 0, > CFG_CLK_SRC_GPLL1, 8); > break; > case GCC_ETH_SLAVE_AHB_CLK: > diff --git a/drivers/clk/qcom/clock-sdm845.c b/drivers/clk/qcom/clock-sdm845.c > index 6af1f38302d2..36ffee79d966 100644 > --- a/drivers/clk/qcom/clock-sdm845.c > +++ b/drivers/clk/qcom/clock-sdm845.c > @@ -27,16 +27,6 @@ > #define SE9_UART_APPS_N 0x18154 > #define SE9_UART_APPS_D 0x18158 > > -#define F(f, s, h, m, n) { (f), (s), (2 * (h) - 1), (m), (n) } > - > -struct freq_tbl { > - uint freq; > - uint src; > - u8 pre_div; > - u16 m; > - u16 n; > -}; > - > static const struct freq_tbl ftbl_gcc_qupv3_wrap0_s0_clk_src[] = { > F(7372800, CFG_CLK_SRC_GPLL0_EVEN, 1, 384, 15625), > F(14745600, CFG_CLK_SRC_GPLL0_EVEN, 1, 768, 15625), > @@ -64,22 +54,6 @@ static const struct bcr_regs uart2_regs = { > .D = SE9_UART_APPS_D, > }; > > -const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, uint rate) > -{ > - if (!f) > - return NULL; > - > - if (!f->freq) > - return f; > - > - for (; f->freq; f++) > - if (rate <= f->freq) > - return f; > - > - /* Default to our fastest rate */ > - return f - 1; > -} > - > static ulong sdm845_clk_set_rate(struct clk *clk, ulong rate) > { > struct msm_clk_priv *priv = dev_get_priv(clk->dev); > > -- > 2.42.0 >
diff --git a/drivers/clk/qcom/clock-apq8016.c b/drivers/clk/qcom/clock-apq8016.c index 630619c83454..eb812934cbae 100644 --- a/drivers/clk/qcom/clock-apq8016.c +++ b/drivers/clk/qcom/clock-apq8016.c @@ -78,7 +78,7 @@ static struct vote_clk gcc_blsp1_ahb_clk = { /* SDHCI */ static int clk_init_sdc(struct msm_clk_priv *priv, int slot, uint rate) { - int div = 8; /* 100MHz default */ + int div = 15; /* 100MHz default */ if (rate == 200000000) div = 4; diff --git a/drivers/clk/qcom/clock-apq8096.c b/drivers/clk/qcom/clock-apq8096.c index 095c1b431245..55f16c14e046 100644 --- a/drivers/clk/qcom/clock-apq8096.c +++ b/drivers/clk/qcom/clock-apq8096.c @@ -65,7 +65,7 @@ static struct vote_clk gcc_blsp2_ahb_clk = { static int clk_init_sdc(struct msm_clk_priv *priv, uint rate) { - int div = 3; + int div = 5; clk_enable_cbc(priv->base + SDCC2_AHB_CBCR); clk_rcg_set_rate_mnd(priv->base, &sdc_regs, div, 0, 0, diff --git a/drivers/clk/qcom/clock-qcom.c b/drivers/clk/qcom/clock-qcom.c index fc478554f982..7c683e519226 100644 --- a/drivers/clk/qcom/clock-qcom.c +++ b/drivers/clk/qcom/clock-qcom.c @@ -19,6 +19,8 @@ #include <dm/lists.h> #include <errno.h> #include <asm/io.h> +#include <linux/bug.h> +#include <linux/delay.h> #include <linux/bitops.h> #include <reset-uclass.h> @@ -68,30 +70,42 @@ void clk_enable_vote_clk(phys_addr_t base, const struct vote_clk *vclk) /* Update clock command via CMD_RCGR */ void clk_bcr_update(phys_addr_t apps_cmd_rcgr) { + u32 count; setbits_le32(apps_cmd_rcgr, APPS_CMD_RCGR_UPDATE); /* Wait for frequency to be updated. */ - while (readl(apps_cmd_rcgr) & APPS_CMD_RCGR_UPDATE) - ; + for (count = 0; count < 50000; count++) { + if (!(readl(apps_cmd_rcgr) & APPS_CMD_RCGR_UPDATE)) + break; + udelay(1); + } + WARN(count == 50000, "WARNING: RCG @ %#llx [%#010x] stuck at off\n", + apps_cmd_rcgr, readl(apps_cmd_rcgr)); } -#define CFG_MODE_DUAL_EDGE (0x2 << 12) /* Counter mode */ +#define CFG_SRC_DIV_MASK 0b11111 +#define CFG_SRC_SEL_SHIFT 8 +#define CFG_SRC_SEL_MASK (0x7 << CFG_SRC_SEL_SHIFT) +#define CFG_MODE_SHIFT 12 +#define CFG_MODE_MASK (0x3 << CFG_MODE_SHIFT) +#define CFG_MODE_DUAL_EDGE (0x2 << CFG_MODE_SHIFT) +#define CFG_HW_CLK_CTRL_MASK BIT(20) -#define CFG_MASK 0x3FFF - -#define CFG_DIVIDER_MASK 0x1F - -/* root set rate for clocks with half integer and MND divider */ +/* + * root set rate for clocks with half integer and MND divider + * div should be pre-calculated ((div * 2) - 1) + */ void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs, int div, int m, int n, int source, u8 mnd_width) { u32 cfg; /* M value for MND divider. */ u32 m_val = m; + u32 n_minus_m = n - m; /* NOT(N-M) value for MND divider. */ - u32 n_val = ~((n) - (m)) * !!(n); + u32 n_val = ~n_minus_m * !!(n); /* NOT 2D value for MND divider. */ - u32 d_val = ~(n); + u32 d_val = ~(clamp_t(u32, n, m, n_minus_m)); u32 mask = BIT(mnd_width) - 1; debug("m %#x n %#x d %#x div %#x mask %#x\n", m_val, n_val, d_val, div, mask); @@ -103,15 +117,13 @@ void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs, /* setup src select and divider */ cfg = readl(base + regs->cfg_rcgr); - cfg &= ~CFG_MASK; - cfg |= source & CFG_CLK_SRC_MASK; /* Select clock source */ + cfg &= ~(CFG_SRC_SEL_MASK | CFG_MODE_MASK | CFG_HW_CLK_CTRL_MASK); + cfg |= source & CFG_SRC_SEL_MASK; /* Select clock source */ - /* Set the divider; HW permits fraction dividers (+0.5), but - for simplicity, we will support integers only */ if (div) - cfg |= (2 * div - 1) & CFG_DIVIDER_MASK; + cfg |= div & CFG_SRC_DIV_MASK; - if (n_val) + if (n && n != m) cfg |= CFG_MODE_DUAL_EDGE; writel(cfg, base + regs->cfg_rcgr); /* Write new clock configuration */ @@ -128,7 +140,7 @@ void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div, /* setup src select and divider */ cfg = readl(base + regs->cfg_rcgr); - cfg &= ~CFG_MASK; + cfg &= ~(CFG_SRC_SEL_MASK | CFG_MODE_MASK | CFG_HW_CLK_CTRL_MASK); cfg |= source & CFG_CLK_SRC_MASK; /* Select clock source */ /* @@ -136,7 +148,7 @@ void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div, * for simplicity, we will support integers only */ if (div) - cfg |= (2 * div - 1) & CFG_DIVIDER_MASK; + cfg |= (2 * div - 1) & CFG_SRC_DIV_MASK; writel(cfg, base + regs->cfg_rcgr); /* Write new clock configuration */ @@ -144,6 +156,22 @@ void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div, clk_bcr_update(base + regs->cmd_rcgr); } +const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, uint rate) +{ + if (!f) + return NULL; + + if (!f->freq) + return f; + + for (; f->freq; f++) + if (rate <= f->freq) + return f; + + /* Default to our fastest rate */ + return f - 1; +} + static int msm_clk_probe(struct udevice *dev) { struct msm_clk_data *data = (struct msm_clk_data *)dev_get_driver_data(dev); diff --git a/drivers/clk/qcom/clock-qcom.h b/drivers/clk/qcom/clock-qcom.h index 24a32cb9666d..01088c19015a 100644 --- a/drivers/clk/qcom/clock-qcom.h +++ b/drivers/clk/qcom/clock-qcom.h @@ -32,6 +32,16 @@ struct bcr_regs { uintptr_t D; }; +struct freq_tbl { + uint freq; + uint src; + u8 pre_div; + u16 m; + u16 n; +}; + +#define F(f, s, h, m, n) { (f), (s), (2 * (h) - 1), (m), (n) } + struct gate_clk { uintptr_t reg; u32 en_val; @@ -71,6 +81,7 @@ void clk_enable_gpll0(phys_addr_t base, const struct pll_vote_clk *gpll0); void clk_bcr_update(phys_addr_t apps_cmd_rgcr); void clk_enable_cbc(phys_addr_t cbcr); void clk_enable_vote_clk(phys_addr_t base, const struct vote_clk *vclk); +const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, uint rate); void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs, int div, int m, int n, int source, u8 mnd_width); void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div, diff --git a/drivers/clk/qcom/clock-qcs404.c b/drivers/clk/qcom/clock-qcs404.c index 921abf1f699b..429ff35e1d1a 100644 --- a/drivers/clk/qcom/clock-qcs404.c +++ b/drivers/clk/qcom/clock-qcs404.c @@ -203,7 +203,7 @@ static ulong qcs404_clk_set_rate(struct clk *clk, ulong rate) break; case GCC_SDCC1_APPS_CLK: /* SDCC1: 200MHz */ - clk_rcg_set_rate_mnd(priv->base, &sdc_regs, 4, 0, 0, + clk_rcg_set_rate_mnd(priv->base, &sdc_regs, 7, 0, 0, CFG_CLK_SRC_GPLL0, 8); clk_enable_gpll0(priv->base, &gpll0_vote_clk); clk_enable_cbc(priv->base + SDCC_APPS_CBCR(1)); @@ -213,16 +213,16 @@ static ulong qcs404_clk_set_rate(struct clk *clk, ulong rate) break; case GCC_ETH_RGMII_CLK: if (rate == 250000000) - clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 0, 0, + clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 0, 0, CFG_CLK_SRC_GPLL1, 8); else if (rate == 125000000) - clk_rcg_set_rate_mnd(priv->base, &emac_regs, 4, 0, 0, + clk_rcg_set_rate_mnd(priv->base, &emac_regs, 7, 0, 0, CFG_CLK_SRC_GPLL1, 8); else if (rate == 50000000) - clk_rcg_set_rate_mnd(priv->base, &emac_regs, 10, 0, 0, + clk_rcg_set_rate_mnd(priv->base, &emac_regs, 19, 0, 0, CFG_CLK_SRC_GPLL1, 8); else if (rate == 5000000) - clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 1, 50, + clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 1, 50, CFG_CLK_SRC_GPLL1, 8); break; default: @@ -239,7 +239,7 @@ static int qcs404_clk_enable(struct clk *clk) switch (clk->id) { case GCC_USB30_MASTER_CLK: clk_enable_cbc(priv->base + USB30_MASTER_CBCR); - clk_rcg_set_rate_mnd(priv->base, &usb30_master_regs, 4, 0, 0, + clk_rcg_set_rate_mnd(priv->base, &usb30_master_regs, 7, 0, 0, CFG_CLK_SRC_GPLL0, 8); break; case GCC_SYS_NOC_USB3_CLK: @@ -261,14 +261,14 @@ static int qcs404_clk_enable(struct clk *clk) /* SPEED_1000: freq -> 250MHz */ clk_enable_cbc(priv->base + ETH_PTP_CBCR); clk_enable_gpll0(priv->base, &gpll1_vote_clk); - clk_rcg_set_rate_mnd(priv->base, &emac_ptp_regs, 2, 0, 0, + clk_rcg_set_rate_mnd(priv->base, &emac_ptp_regs, 3, 0, 0, CFG_CLK_SRC_GPLL1, 8); break; case GCC_ETH_RGMII_CLK: /* SPEED_1000: freq -> 250MHz */ clk_enable_cbc(priv->base + ETH_RGMII_CBCR); clk_enable_gpll0(priv->base, &gpll1_vote_clk); - clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 0, 0, + clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 0, 0, CFG_CLK_SRC_GPLL1, 8); break; case GCC_ETH_SLAVE_AHB_CLK: diff --git a/drivers/clk/qcom/clock-sdm845.c b/drivers/clk/qcom/clock-sdm845.c index 6af1f38302d2..36ffee79d966 100644 --- a/drivers/clk/qcom/clock-sdm845.c +++ b/drivers/clk/qcom/clock-sdm845.c @@ -27,16 +27,6 @@ #define SE9_UART_APPS_N 0x18154 #define SE9_UART_APPS_D 0x18158 -#define F(f, s, h, m, n) { (f), (s), (2 * (h) - 1), (m), (n) } - -struct freq_tbl { - uint freq; - uint src; - u8 pre_div; - u16 m; - u16 n; -}; - static const struct freq_tbl ftbl_gcc_qupv3_wrap0_s0_clk_src[] = { F(7372800, CFG_CLK_SRC_GPLL0_EVEN, 1, 384, 15625), F(14745600, CFG_CLK_SRC_GPLL0_EVEN, 1, 768, 15625), @@ -64,22 +54,6 @@ static const struct bcr_regs uart2_regs = { .D = SE9_UART_APPS_D, }; -const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, uint rate) -{ - if (!f) - return NULL; - - if (!f->freq) - return f; - - for (; f->freq; f++) - if (rate <= f->freq) - return f; - - /* Default to our fastest rate */ - return f - 1; -} - static ulong sdm845_clk_set_rate(struct clk *clk, ulong rate) { struct msm_clk_priv *priv = dev_get_priv(clk->dev);
The RCG divider field takes a value of (2*h - 1) where h is the divisor. This allows fractional dividers to be supported by calculating them at compile time using a macro. However, the clk_rcg_set_rate_mnd() function was also performing the calculation. Clean this all up and consistently use the F() macro to calculate these at compile time and properly support fractional divisors. Additionally, improve clk_bcr_update() to timeout with a warning rather than hanging the board, and make the freq_tbl struct and helpers common so that they can be reused by future platforms. Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> --- drivers/clk/qcom/clock-apq8016.c | 2 +- drivers/clk/qcom/clock-apq8096.c | 2 +- drivers/clk/qcom/clock-qcom.c | 64 +++++++++++++++++++++++++++++----------- drivers/clk/qcom/clock-qcom.h | 11 +++++++ drivers/clk/qcom/clock-qcs404.c | 16 +++++----- drivers/clk/qcom/clock-sdm845.c | 26 ---------------- 6 files changed, 67 insertions(+), 54 deletions(-)