diff mbox series

[v2,30/40] mmc: exynos_dw_mmc: Read and use DDR timing when available

Message ID 20240610011226.4050-31-semen.protsenko@linaro.org
State Superseded
Headers show
Series mmc: dw_mmc: Enable eMMC on E850-96 board | expand

Commit Message

Sam Protsenko June 10, 2024, 1:12 a.m. UTC 
DDR timing values should be defined in "samsung,dw-mshc-ddr-timing" dts
property, and used when DDR MMC mode is selected. Read that value from
dts and use it. If it's not available, use SDR timing values instead.
This change is following upstream Linux kernel implementation.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
---
 drivers/mmc/exynos_dw_mmc.c | 20 +++++++++++++++++++-
 1 file changed, 19 insertions(+), 1 deletion(-)
diff mbox series

Patch

diff --git a/drivers/mmc/exynos_dw_mmc.c b/drivers/mmc/exynos_dw_mmc.c
index 69ba19e9edca..ef03eac5657b 100644
--- a/drivers/mmc/exynos_dw_mmc.c
+++ b/drivers/mmc/exynos_dw_mmc.c
@@ -53,6 +53,7 @@  struct dwmci_exynos_priv_data {
 #endif
 	struct clk clk;
 	u32 sdr_timing;
+	u32 ddr_timing;
 	const struct exynos_dwmmc_variant *chip;
 };
 
@@ -128,8 +129,14 @@  static int exynos_dwmmc_set_sclk(struct dwmci_host *host, unsigned long rate)
 static int exynos_dwmci_clksel(struct dwmci_host *host)
 {
 	struct dwmci_exynos_priv_data *priv = exynos_dwmmc_get_priv(host);
+	u32 timing;
 
-	dwmci_writel(host, priv->chip->clksel, priv->sdr_timing);
+	if (host->mmc->selected_mode == MMC_DDR_52)
+		timing = priv->ddr_timing;
+	else
+		timing = priv->sdr_timing;
+
+	dwmci_writel(host, priv->chip->clksel, timing);
 
 	return 0;
 }
@@ -306,6 +313,17 @@  static int exynos_dwmmc_of_to_plat(struct udevice *dev)
 			priv->sdr_timing = DWMMC_MMC2_SDR_TIMING_VAL;
 	}
 
+	err = dev_read_u32_array(dev, "samsung,dw-mshc-ddr-timing", timing, 2);
+	if (err) {
+		debug("DWMMC%d: Can't get ddr-timings, using sdr-timings\n",
+		      host->dev_index);
+		priv->ddr_timing = priv->sdr_timing;
+	} else {
+		priv->ddr_timing = DWMCI_SET_SAMPLE_CLK(timing[0]) |
+				   DWMCI_SET_DRV_CLK(timing[1]) |
+				   DWMCI_SET_DIV_RATIO(div);
+	}
+
 	host->fifo_depth = dev_read_u32_default(dev, "fifo-depth", 0);
 	host->bus_hz = dev_read_u32_default(dev, "clock-frequency", 0);