@@ -27,6 +27,12 @@ config PCIE_XILINX_NWL
or End Point. The current option selection will only
support root port enabling.
+config PCI_FTPCI100
+ bool "Faraday Technology FTPCI100 PCI controller"
+ depends on OF
+ depends on ARM
+ default ARCH_GEMINI
+
config PCI_TEGRA
bool "NVIDIA Tegra PCIe controller"
depends on ARCH_TEGRA
@@ -1,3 +1,4 @@
+obj-$(CONFIG_PCI_FTPCI100) += pci-ftpci100.o
obj-$(CONFIG_PCI_HYPERV) += pci-hyperv.o
obj-$(CONFIG_PCI_MVEBU) += pci-mvebu.o
obj-$(CONFIG_PCI_AARDVARK) += pci-aardvark.o
new file mode 100644
@@ -0,0 +1,566 @@
+/*
+ * Support for Faraday Technology FTPC100 PCI Controller
+ *
+ * Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
+ *
+ * Based on the out-of-tree OpenWRT patch for Cortina Gemini:
+ * Copyright (C) 2009 Janos Laube <janos.dev@gmail.com>
+ * Copyright (C) 2009 Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
+ * Based on SL2312 PCI controller code
+ * Storlink (C) 2003
+ */
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/irqdomain.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/bitops.h>
+#include <linux/irq.h>
+
+/*
+ * Special configuration registers directly in the first few words
+ * in he I/O space.
+ */
+#define PCI_IOSIZE 0x00
+#define PCI_PROT 0x04 /* AHB protection */
+#define PCI_CTRL 0x08 /* PCI control signal */
+#define PCI_SOFTRST 0x10 /* Soft reset counter and response error enable */
+#define PCI_CONFIG 0x28 /* PCI configuration command register */
+#define PCI_DATA 0x2C
+
+#define FARADAY_PCI_PMC 0x40 /* Power management control */
+#define FARADAY_PCI_PMCSR 0x44 /* Power management status */
+#define FARADAY_PCI_CTRL1 0x48 /* Control register 1 */
+#define FARADAY_PCI_CTRL2 0x4C /* Control register 2 */
+#define FARADAY_PCI_MEM1_BASE_SIZE 0x50 /* Memory base and size #1 */
+#define FARADAY_PCI_MEM2_BASE_SIZE 0x54 /* Memory base and size #2 */
+#define FARADAY_PCI_MEM3_BASE_SIZE 0x58 /* Memory base and size #3 */
+
+/* Bits 31..28 gives INTD..INTA status */
+#define PCI_CTRL2_INTSTS_SHIFT 28
+#define PCI_CTRL2_INTMASK_CMDERR BIT(27)
+#define PCI_CTRL2_INTMASK_PARERR BIT(26)
+/* Bits 25..22 masks INTD..INTA */
+#define PCI_CTRL2_INTMASK_SHIFT 22
+#define PCI_CTRL2_INTMASK_MABRT_RX BIT(21)
+#define PCI_CTRL2_INTMASK_TABRT_RX BIT(20)
+#define PCI_CTRL2_INTMASK_TABRT_TX BIT(19)
+#define PCI_CTRL2_INTMASK_RETRY4 BIT(18)
+#define PCI_CTRL2_INTMASK_SERR_RX BIT(17)
+#define PCI_CTRL2_INTMASK_PERR_RX BIT(16)
+/* Bit 15 reserved */
+#define PCI_CTRL2_MSTPRI_REQ6 BIT(14)
+#define PCI_CTRL2_MSTPRI_REQ5 BIT(13)
+#define PCI_CTRL2_MSTPRI_REQ4 BIT(12)
+#define PCI_CTRL2_MSTPRI_REQ3 BIT(11)
+#define PCI_CTRL2_MSTPRI_REQ2 BIT(10)
+#define PCI_CTRL2_MSTPRI_REQ1 BIT(9)
+#define PCI_CTRL2_MSTPRI_REQ0 BIT(8)
+/* Bits 7..4 reserved */
+/* Bits 3..0 TRDYW */
+
+/*
+ * Memory configs:
+ * Bit 31..20 defines the PCI side memory base
+ * Bit 19..16 (4 bits) defines the size per below
+ */
+#define FARADAY_PCI_MEMBASE_MASK 0xfff00000
+#define FARADAY_PCI_MEMSIZE_1MB 0x0
+#define FARADAY_PCI_MEMSIZE_2MB 0x1
+#define FARADAY_PCI_MEMSIZE_4MB 0x2
+#define FARADAY_PCI_MEMSIZE_8MB 0x3
+#define FARADAY_PCI_MEMSIZE_16MB 0x4
+#define FARADAY_PCI_MEMSIZE_32MB 0x5
+#define FARADAY_PCI_MEMSIZE_64MB 0x6
+#define FARADAY_PCI_MEMSIZE_128MB 0x7
+#define FARADAY_PCI_MEMSIZE_256MB 0x8
+#define FARADAY_PCI_MEMSIZE_512MB 0x9
+#define FARADAY_PCI_MEMSIZE_1GB 0xa
+#define FARADAY_PCI_MEMSIZE_2GB 0xb
+#define FARADAY_PCI_MEMSIZE_SHIFT 16
+
+/*
+ * The DMA base is set to 0x0 for all memory segments, it reflects the
+ * fact that the memory of the host system starts at 0x0.
+ */
+#define FARADAY_PCI_DMA_MEM1_BASE 0x00000000
+#define FARADAY_PCI_DMA_MEM2_BASE 0x00000000
+#define FARADAY_PCI_DMA_MEM3_BASE 0x00000000
+
+/* Defines for PCI configuration command register */
+#define PCI_CONF_ENABLE BIT(31)
+#define PCI_CONF_WHERE(r) ((r) & 0xFC)
+#define PCI_CONF_BUS(b) (((b) & 0xFF) << 16)
+#define PCI_CONF_DEVICE(d) (((d) & 0x1F) << 11)
+#define PCI_CONF_FUNCTION(f) (((f) & 0x07) << 8)
+
+/**
+ * struct faraday_pci_variant - encodes IP block differences
+ * @cascaded_irq: this host has cascaded IRQs from an interrupt controller
+ * embedded in the host bridge.
+ */
+struct faraday_pci_variant {
+ bool cascaded_irq;
+};
+
+struct faraday_pci {
+ struct device *dev;
+ void __iomem *base;
+ struct irq_domain *irqdomain;
+ struct pci_bus *bus;
+};
+
+static int faraday_res_to_memcfg(resource_size_t mem_base,
+ resource_size_t mem_size,
+ u32 *val)
+{
+ u32 outval;
+
+ switch (mem_size) {
+ case SZ_1M:
+ outval = FARADAY_PCI_MEMSIZE_1MB;
+ break;
+ case SZ_2M:
+ outval = FARADAY_PCI_MEMSIZE_2MB;
+ break;
+ case SZ_4M:
+ outval = FARADAY_PCI_MEMSIZE_4MB;
+ break;
+ case SZ_8M:
+ outval = FARADAY_PCI_MEMSIZE_8MB;
+ break;
+ case SZ_16M:
+ outval = FARADAY_PCI_MEMSIZE_16MB;
+ break;
+ case SZ_32M:
+ outval = FARADAY_PCI_MEMSIZE_32MB;
+ break;
+ case SZ_64M:
+ outval = FARADAY_PCI_MEMSIZE_64MB;
+ break;
+ case SZ_128M:
+ outval = FARADAY_PCI_MEMSIZE_128MB;
+ break;
+ case SZ_256M:
+ outval = FARADAY_PCI_MEMSIZE_256MB;
+ break;
+ case SZ_512M:
+ outval = FARADAY_PCI_MEMSIZE_512MB;
+ break;
+ case SZ_1G:
+ outval = FARADAY_PCI_MEMSIZE_1GB;
+ break;
+ case SZ_2G:
+ outval = FARADAY_PCI_MEMSIZE_2GB;
+ break;
+ default:
+ return -EINVAL;
+ }
+ outval <<= FARADAY_PCI_MEMSIZE_SHIFT;
+
+ /* This is probably not good */
+ if (mem_base & ~(FARADAY_PCI_MEMBASE_MASK))
+ pr_warn("truncated PCI memory base\n");
+ /* Translate to bridge side address space */
+ outval |= (mem_base & FARADAY_PCI_MEMBASE_MASK);
+ pr_debug("Translated pci base @%08x, size %08x to config %08x\n",
+ mem_base, mem_size, outval);
+
+ *val = outval;
+ return 0;
+}
+
+static int faraday_pci_read_config(struct pci_bus *bus, unsigned int fn,
+ int config, int size, u32 *value)
+{
+ struct faraday_pci *p = bus->sysdata;
+
+ writel(PCI_CONF_BUS(bus->number) |
+ PCI_CONF_DEVICE(PCI_SLOT(fn)) |
+ PCI_CONF_FUNCTION(PCI_FUNC(fn)) |
+ PCI_CONF_WHERE(config) |
+ PCI_CONF_ENABLE,
+ p->base + PCI_CONFIG);
+
+ *value = readl(p->base + PCI_DATA);
+
+ if (size == 1)
+ *value = (*value >> (8 * (config & 3))) & 0xFF;
+ else if (size == 2)
+ *value = (*value >> (8 * (config & 3))) & 0xFFFF;
+
+ dev_dbg(&bus->dev,
+ "[read] slt: %.2d, fnc: %d, cnf: 0x%.2X, val (%d bytes): 0x%.8X\n",
+ PCI_SLOT(fn), PCI_FUNC(fn), config, size, *value);
+
+ return PCIBIOS_SUCCESSFUL;
+}
+
+static int faraday_pci_write_config(struct pci_bus *bus, unsigned int fn,
+ int config, int size, u32 value)
+{
+ struct faraday_pci *p = bus->sysdata;
+ int ret = PCIBIOS_SUCCESSFUL;
+
+ dev_dbg(&bus->dev,
+ "[write] slt: %.2d, fnc: %d, cnf: 0x%.2X, val (%d bytes): 0x%.8X\n",
+ PCI_SLOT(fn), PCI_FUNC(fn), config, size, value);
+
+ writel(PCI_CONF_BUS(bus->number) |
+ PCI_CONF_DEVICE(PCI_SLOT(fn)) |
+ PCI_CONF_FUNCTION(PCI_FUNC(fn)) |
+ PCI_CONF_WHERE(config) |
+ PCI_CONF_ENABLE,
+ p->base + PCI_CONFIG);
+
+ switch (size) {
+ case 4:
+ writel(value, p->base + PCI_DATA);
+ break;
+ case 2:
+ writew(value, p->base + PCI_DATA + (config & 3));
+ break;
+ case 1:
+ writeb(value, p->base + PCI_DATA + (config & 3));
+ break;
+ default:
+ ret = PCIBIOS_BAD_REGISTER_NUMBER;
+ }
+
+ return ret;
+}
+
+static struct pci_ops faraday_pci_ops = {
+ .read = faraday_pci_read_config,
+ .write = faraday_pci_write_config,
+};
+
+static void faraday_pci_ack_irq(struct irq_data *d)
+{
+ struct faraday_pci *p = irq_data_get_irq_chip_data(d);
+ unsigned int reg;
+
+ faraday_pci_read_config(p->bus, 0, FARADAY_PCI_CTRL2, 4, ®);
+ reg &= ~(0xF << PCI_CTRL2_INTSTS_SHIFT);
+ reg |= BIT(irqd_to_hwirq(d) + PCI_CTRL2_INTSTS_SHIFT);
+ faraday_pci_write_config(p->bus, 0, FARADAY_PCI_CTRL2, 4, reg);
+}
+
+static void faraday_pci_mask_irq(struct irq_data *d)
+{
+ struct faraday_pci *p = irq_data_get_irq_chip_data(d);
+ unsigned int reg;
+
+ faraday_pci_read_config(p->bus, 0, FARADAY_PCI_CTRL2, 4, ®);
+ reg &= ~((0xF << PCI_CTRL2_INTSTS_SHIFT)
+ | BIT(irqd_to_hwirq(d) + PCI_CTRL2_INTMASK_SHIFT));
+ faraday_pci_write_config(p->bus, 0, FARADAY_PCI_CTRL2, 4, reg);
+}
+
+static void faraday_pci_unmask_irq(struct irq_data *d)
+{
+ struct faraday_pci *p = irq_data_get_irq_chip_data(d);
+ unsigned int reg;
+
+ faraday_pci_read_config(p->bus, 0, FARADAY_PCI_CTRL2, 4, ®);
+ reg &= ~(0xF << PCI_CTRL2_INTSTS_SHIFT);
+ reg |= BIT(irqd_to_hwirq(d) + PCI_CTRL2_INTMASK_SHIFT);
+ faraday_pci_write_config(p->bus, 0, FARADAY_PCI_CTRL2, 4, reg);
+}
+
+static void faraday_pci_irq_handler(struct irq_desc *desc)
+{
+ struct faraday_pci *p = irq_desc_get_handler_data(desc);
+ struct irq_chip *irqchip = irq_desc_get_chip(desc);
+ unsigned int irq_stat, reg, i;
+
+ faraday_pci_read_config(p->bus, 0, FARADAY_PCI_CTRL2, 4, ®);
+ irq_stat = reg >> PCI_CTRL2_INTSTS_SHIFT;
+
+ chained_irq_enter(irqchip, desc);
+
+ for (i = 0; i < 4; i++) {
+ if ((irq_stat & BIT(i)) == 0)
+ continue;
+ generic_handle_irq(irq_find_mapping(p->irqdomain, i));
+ }
+
+ chained_irq_exit(irqchip, desc);
+}
+
+static struct irq_chip faraday_pci_irq_chip = {
+ .name = "PCI",
+ .irq_ack = faraday_pci_ack_irq,
+ .irq_mask = faraday_pci_mask_irq,
+ .irq_unmask = faraday_pci_unmask_irq,
+};
+
+static int faraday_pci_irq_map(struct irq_domain *domain, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_chip_and_handler(irq, &faraday_pci_irq_chip, handle_level_irq);
+ irq_set_chip_data(irq, domain->host_data);
+
+ return 0;
+}
+
+static const struct irq_domain_ops faraday_pci_irqdomain_ops = {
+ .map = faraday_pci_irq_map,
+};
+
+static int faraday_pci_setup_cascaded_irq(struct faraday_pci *p)
+{
+ struct device_node *intc = of_get_next_child(p->dev->of_node, NULL);
+ int irq;
+ int i;
+
+ if (!intc) {
+ dev_err(p->dev, "missing child interrupt-controller node\n");
+ return -EINVAL;
+ }
+
+ /* All PCI IRQs cascade off this one */
+ irq = of_irq_get(intc, 0);
+ if (!irq) {
+ dev_err(p->dev, "failed to get parent IRQ\n");
+ return -EINVAL;
+ }
+
+ p->irqdomain = irq_domain_add_linear(intc, 4,
+ &faraday_pci_irqdomain_ops,
+ p);
+ if (!p->irqdomain) {
+ dev_err(p->dev, "failed to create Gemini PCI IRQ domain\n");
+ return -EINVAL;
+ }
+
+ irq_set_chained_handler_and_data(irq, faraday_pci_irq_handler, p);
+
+ for (i = 0; i < 4; i++)
+ irq_create_mapping(p->irqdomain, i);
+
+ return 0;
+}
+
+static int pci_dma_range_parser_init(struct of_pci_range_parser *parser,
+ struct device_node *node)
+{
+ const int na = 3, ns = 2;
+ int rlen;
+
+ parser->node = node;
+ parser->pna = of_n_addr_cells(node);
+ parser->np = parser->pna + na + ns;
+
+ parser->range = of_get_property(node, "dma-ranges", &rlen);
+ if (!parser->range)
+ return -ENOENT;
+ parser->end = parser->range + rlen / sizeof(__be32);
+
+ return 0;
+}
+
+static int faraday_pci_parse_map_dma_ranges(struct faraday_pci *p,
+ struct device_node *np)
+{
+ struct of_pci_range range;
+ struct of_pci_range_parser parser;
+ struct device *dev = p->dev;
+ u32 confreg[3] = {
+ FARADAY_PCI_MEM1_BASE_SIZE,
+ FARADAY_PCI_MEM2_BASE_SIZE,
+ FARADAY_PCI_MEM3_BASE_SIZE,
+ };
+ int i = 0;
+ u32 val;
+
+ if (pci_dma_range_parser_init(&parser, np)) {
+ dev_err(dev, "missing dma-ranges property\n");
+ return -EINVAL;
+ }
+
+ /*
+ * Get the dma-ranges from the device tree
+ */
+ for_each_of_pci_range(&parser, &range) {
+ u64 end = range.pci_addr + range.size - 1;
+ int ret;
+
+ ret = faraday_res_to_memcfg(range.pci_addr, range.size, &val);
+ if (ret) {
+ dev_err(dev,
+ "DMA range %d: illegal MEM resource size\n", i);
+ return -EINVAL;
+ }
+
+ dev_info(dev, "DMA MEM%d BASE: 0x%016llx -> 0x%016llx config %08x\n",
+ i + 1, range.pci_addr, end, val);
+ if (i <= 2) {
+ faraday_pci_write_config(p->bus, 0, confreg[i],
+ 4, val);
+ } else {
+ dev_err(dev, "ignore extraneous dma-range %d\n", i);
+ break;
+ }
+
+ i++;
+ }
+
+ return 0;
+}
+
+static int faraday_pci_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct faraday_pci_variant *variant =
+ of_device_get_match_data(dev);
+ struct resource *regs;
+ resource_size_t io_base;
+ struct resource_entry *win;
+ struct faraday_pci *p;
+ struct resource *mem;
+ struct resource *io;
+ struct pci_host_bridge *host;
+ int ret;
+ u32 val;
+ LIST_HEAD(res);
+
+ host = pci_alloc_host_bridge(sizeof(*p));
+ if (!host)
+ return -ENOMEM;
+
+ host->dev.parent = dev;
+ host->ops = &faraday_pci_ops;
+ host->busnr = 0;
+ host->msi = NULL;
+ p = pci_host_bridge_priv(host);
+ host->sysdata = p;
+ p->dev = dev;
+
+ regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ p->base = devm_ioremap_resource(dev, regs);
+ if (IS_ERR(p->base))
+ return PTR_ERR(p->base);
+
+ ret = of_pci_get_host_bridge_resources(dev->of_node, 0, 0xff,
+ &res, &io_base);
+ if (ret)
+ return ret;
+
+ ret = devm_request_pci_bus_resources(dev, &res);
+ if (ret)
+ return ret;
+
+ /* Get the I/O and memory ranges from DT */
+ resource_list_for_each_entry(win, &res) {
+ switch (resource_type(win->res)) {
+ case IORESOURCE_IO:
+ io = win->res;
+ io->name = "Gemini PCI I/O";
+ if (!faraday_res_to_memcfg(io->start - win->offset,
+ resource_size(io),
+ &val)) {
+ /* setup I/O space size */
+ writel(val, p->base + PCI_IOSIZE);
+ } else {
+ dev_err(dev,
+ "illegal IO mem size\n");
+ return -EINVAL;
+ }
+ ret = pci_remap_iospace(io, io_base);
+ if (ret) {
+ dev_warn(dev, "error %d: failed to map resource %pR\n",
+ ret, io);
+ continue;
+ }
+ break;
+ case IORESOURCE_MEM:
+ mem = win->res;
+ mem->name = "Gemini PCI MEM";
+ break;
+ case IORESOURCE_BUS:
+ break;
+ default:
+ break;
+ }
+ }
+
+ /* Setup hostbridge */
+ val = readl(p->base + PCI_CTRL);
+ val |= PCI_COMMAND_IO;
+ val |= PCI_COMMAND_MEMORY;
+ val |= PCI_COMMAND_MASTER;
+ writel(val, p->base + PCI_CTRL);
+
+ list_splice_init(&res, &host->windows);
+ ret = pci_register_host_bridge(host);
+ if (ret) {
+ dev_err(dev, "failed to register host: %d\n", ret);
+ return ret;
+ }
+ p->bus = host->bus;
+
+ /* Mask and clear all interrupts */
+ faraday_pci_write_config(p->bus, 0, FARADAY_PCI_CTRL2 + 2, 2, 0xF000);
+ if (variant->cascaded_irq) {
+ ret = faraday_pci_setup_cascaded_irq(p);
+ if (ret) {
+ dev_err(dev, "failed to setup cascaded IRQ\n");
+ return ret;
+ }
+ }
+
+ ret = faraday_pci_parse_map_dma_ranges(p, dev->of_node);
+ if (ret)
+ return ret;
+
+ pci_scan_child_bus(p->bus);
+ pci_fixup_irqs(pci_common_swizzle, of_irq_parse_and_map_pci);
+ pci_bus_assign_resources(p->bus);
+ pci_bus_add_devices(p->bus);
+ pci_free_resource_list(&res);
+
+ return 0;
+}
+
+/*
+ * We encode bridge variants here, we have at least two so it doesn't
+ * hurt to have infrastructure to encompass future variants as well.
+ */
+const struct faraday_pci_variant faraday_regular = {
+ .cascaded_irq = true,
+};
+
+const struct faraday_pci_variant faraday_dual = {
+ .cascaded_irq = false,
+};
+
+static const struct of_device_id faraday_pci_of_match[] = {
+ {
+ .compatible = "faraday,ftpci100",
+ .data = &faraday_regular,
+ },
+ {
+ .compatible = "faraday,ftpci100-dual",
+ .data = &faraday_dual,
+ },
+ {},
+};
+
+static struct platform_driver faraday_pci_driver = {
+ .driver = {
+ .name = "ftpci100",
+ .of_match_table = of_match_ptr(faraday_pci_of_match),
+ },
+ .probe = faraday_pci_probe,
+};
+builtin_platform_driver(faraday_pci_driver);
This adds a host bridge driver for the Faraday Technology FPPCI100 host bridge, used for Cortina Systems Gemini SoC (SL3516) PCI Host Bridge. This code is inspired by the out-of-tree OpenWRT patch and then extensively rewritten for device tree and using the modern helpers to cut down and modernize the code to all new PCI frameworks. A driver exists in U-Boot as well. Tested on the ITian Square One SQ201 NAS with the following result in the boot log (trimmed to relevant parts): OF: PCI: host bridge /soc/pci@50000000 ranges: OF: PCI: IO 0x50000000..0x500fffff -> 0x00000000 OF: PCI: MEM 0x58000000..0x5fffffff -> 0x58000000 ftpci100 50000000.pci: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] pci_bus 0000:00: root bus resource [mem 0x58000000-0x5fffffff] ftpci100 50000000.pci: DMA MEM1 BASE: 0x0000000000000000 -> 0x0000000007ffffff config 00070000 ftpci100 50000000.pci: DMA MEM2 BASE: 0x0000000000000000 -> 0x0000000003ffffff config 00060000 ftpci100 50000000.pci: DMA MEM3 BASE: 0x0000000000000000 -> 0x0000000003ffffff config 00060000 PCI: bus0: Fast back to back transfers disabled pci 0000:00:00.0: of_irq_parse_pci() failed with rc=-22 pci 0000:00:0c.0: BAR 0: assigned [mem 0x58000000-0x58007fff] pci 0000:00:09.2: BAR 0: assigned [mem 0x58008000-0x580080ff] pci 0000:00:09.0: BAR 4: assigned [io 0x1000-0x101f] pci 0000:00:09.1: BAR 4: assigned [io 0x1020-0x103f] pci 0000:00:09.0: enabling device (0140 -> 0141) pci 0000:00:09.0: HCRESET not completed yet! pci 0000:00:09.1: enabling device (0140 -> 0141) pci 0000:00:09.1: HCRESET not completed yet! pci 0000:00:09.2: enabling device (0140 -> 0142) rt61pci 0000:00:0c.0: enabling device (0140 -> 0142) ieee80211 phy0: rt2x00_set_chip: Info - Chipset detected - rt: 2561, rf: 0003, rev: 000c ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-pci 0000:00:09.2: EHCI Host Controller ehci-pci 0000:00:09.2: new USB bus registered, assigned bus number 1 ehci-pci 0000:00:09.2: irq 125, io mem 0x58008000 ehci-pci 0000:00:09.2: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected uhci_hcd: USB Universal Host Controller Interface driver uhci_hcd 0000:00:09.0: UHCI Host Controller uhci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:09.0: HCRESET not completed yet! uhci_hcd 0000:00:09.0: irq 123, io base 0x00001000 hub 2-0:1.0: USB hub found hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) uhci_hcd 0000:00:09.1: UHCI Host Controller uhci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:09.1: HCRESET not completed yet! uhci_hcd 0000:00:09.1: irq 124, io base 0x00001020 hub 3-0:1.0: USB hub found hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19) scsi 0:0:0:0: Direct-Access USB Flash Disk 1.00 PQ: 0 ANSI: 2 sd 0:0:0:0: [sda] 7900336 512-byte logical blocks: (4.04 GB/3.77 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] No Caching mode page found sd 0:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI removable disk ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2561s.bin' ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.8 IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready $ lspci 00:00.0 Class 0600: 159b:4321 00:09.2 Class 0c03: 1106:3104 00:09.0 Class 0c03: 1106:3038 00:09.1 Class 0c03: 1106:3038 00:0c.0 Class 0280: 1814:0301 cat /proc/interrupts CPU0 123: 0 PCI 0 Edge uhci_hcd:usb2 124: 0 PCI 1 Edge uhci_hcd:usb3 125: 159 PCI 2 Edge ehci_hcd:usb1 126: 1082 PCI 3 Edge rt61pci cat /proc/iomem 50000000-500000ff : /soc/pci@50000000 58000000-5fffffff : Gemini PCI MEM 58000000-58007fff : 0000:00:0c.0 58000000-58007fff : 0000:00:0c.0 58008000-580080ff : 0000:00:09.2 58008000-580080ff : ehci_hcd The EHCI USB hub works fine, I can mount and manage files and the IRQs just keep ticking up. I can issue iwlist wlan0 scanning and see all the WLANs here, I don't have wpa_supplicant so have not tried connecting to them. Cc: Janos Laube <janos.dev@gmail.com> Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com> Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Feng-Hsin Chiang <john453@faraday-tech.com> Cc: Greentime Hu <green.hu@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v4->v5: - Rebase to v4.11-rc1 ChangeLog v3->v4: - Change pr_dbg() to pr_debug(). The former does not exist and for some reason I first changed pr_info() to pr_dbg() and didn't test-compile it before submitting, mea culpa. ChangeLog v2->v3: - Rewrite to use pci_alloc_host_bridge() and pci_register_host_bridge() - Change compatible strings to "faraday,ftpci100" and "faraday,ftpci100-dual" - Rename driver file to pci-ftpci100.c to reflect the name of the actual Faraday IP core. - Make the driver depend on ARM again as not all archs use setup-irq.c which contains pci_fixup_irqs() that the driver is using. - Add "dma-ranges" property, after deciphering that some hardcoded constants in the driver is really about this. ChangeLog v1->v2: - Rename the bridge and symbols to reflect Faraday technology as this IP block is clearly a Faraday block and not from Storlink/Storm/Cortina at all. - Support both the regular and "dual" versions of the bridge, where the regular has a cascaded IRQ controller and the dual does not. - Encode per-variant characteristics in a variant struct in the .data field of the OF match. - Drop the pointless spinlock in the config space accessors. - Drop manipulation of pcibios_min_io and pcibios_min_mem - Get the IO range size from the device tree, and set up the bridge properly according to this. Currently we only support a 1MiB size IO range, but hey, it's at least dynamic and logical. This can be merged to the PCI tree whenever it is considered fine for inclusion. Andestech and Faraday guys: you are more likely than me to actually have documentation for this bridge. Please share with me if you can, especially the register defintions, because I want to set up IO and MEM windows properly from the device tree, not just rely on defaults. There are defines for these registers but no use or documentation. --- drivers/pci/host/Kconfig | 6 + drivers/pci/host/Makefile | 1 + drivers/pci/host/pci-ftpci100.c | 566 ++++++++++++++++++++++++++++++++++++++++ 3 files changed, 573 insertions(+) create mode 100644 drivers/pci/host/pci-ftpci100.c -- 2.9.3 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html