| Message ID | 20170517083745.24479-7-guodong.xu@linaro.org |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [01/12] dt-bindings: arm: hisilicon: add bindings for HiKey960 board | expand |
On Wed, May 17, 2017 at 04:37:39PM +0800, Guodong Xu wrote: > From: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com> > > This patch adds pl061 device nodes for Hi3660 SoC. > > Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com> > --- > arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 409 ++++++++++++++++++++++++++++++ > 1 file changed, 409 insertions(+) > > diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi > index f217c9d..3bea0d2 100644 > --- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi > +++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi > @@ -251,5 +251,414 @@ > clock-names = "uartclk", "apb_pclk"; > status = "disabled"; > }; > + > + gpio0: gpio@e8a0b000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a0b000 0 0x1000>; > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 1 0 7>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO0>; > + clock-names = "apb_pclk"; > + status = "ok"; You don't need "ok" here if these are default enabled. > + }; > + > + gpio1: gpio@e8a0c000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a0c000 0 0x1000>; > + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 1 7 7>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO1>; > + clock-names = "apb_pclk"; > + status = "ok"; ditto... > + }; > + > + gpio2: gpio@e8a0d000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a0d000 0 0x1000>; > + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 14 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO2>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio3: gpio@e8a0e000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a0e000 0 0x1000>; > + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 22 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO3>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio4: gpio@e8a0f000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a0f000 0 0x1000>; > + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 30 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO4>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio5: gpio@e8a10000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a10000 0 0x1000>; > + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 38 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO5>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio6: gpio@e8a11000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a11000 0 0x1000>; > + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 46 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO6>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio7: gpio@e8a12000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a12000 0 0x1000>; > + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 54 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO7>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio8: gpio@e8a13000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a13000 0 0x1000>; > + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 62 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO8>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio9: gpio@e8a14000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a14000 0 0x1000>; > + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 70 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO9>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio10: gpio@e8a15000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a15000 0 0x1000>; > + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 78 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO10>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio11: gpio@e8a16000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a16000 0 0x1000>; > + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 86 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO11>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio12: gpio@e8a17000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a17000 0 0x1000>; > + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 94 3 &pmx0 7 101 1>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO12>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio13: gpio@e8a18000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a18000 0 0x1000>; > + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 102 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO13>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio14: gpio@e8a19000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a19000 0 0x1000>; > + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 110 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO14>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio15: gpio@e8a1a000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a1a000 0 0x1000>; > + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx0 0 118 6>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO15>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio16: gpio@e8a1b000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a1b000 0 0x1000>; > + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO16>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio17: gpio@e8a1c000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a1c000 0 0x1000>; > + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO17>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio18: gpio@ff3b4000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xff3b4000 0 0x1000>; > + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx2 0 0 8>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO18>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio19: gpio@ff3b5000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xff3b5000 0 0x1000>; > + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx2 0 8 4>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO19>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio20: gpio@e8a1f000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a1f000 0 0x1000>; > + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&pmx1 0 0 6>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO20>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio21: gpio@e8a20000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xe8a20000 0 0x1000>; > + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + gpio-ranges = <&pmx3 0 0 6>; > + clocks = <&crg_ctrl HI3660_PCLK_GPIO21>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio22: gpio@fff0b000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xfff0b000 0 0x1000>; > + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + /* GPIO176 */ > + gpio-ranges = <&pmx4 2 0 6>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&sctrl HI3660_PCLK_AO_GPIO0>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio23: gpio@fff0c000 { > + compatible = "arm,pl061", "arm,primecell"; > + reg = <0 0xfff0c000 0 0x1000>; > + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + /* GPIO184 */ > + gpio-ranges = <&pmx4 0 6 7>; > + interrupt-controller; > + #interrupt-cells = <2>; > + clocks = <&sctrl HI3660_PCLK_AO_GPIO1>; > + clock-names = "apb_pclk"; > + status = "ok"; > + }; > + > + gpio24: gpio@fff0d000 { extra space ^ -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi index f217c9d..3bea0d2 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi @@ -251,5 +251,414 @@ clock-names = "uartclk", "apb_pclk"; status = "disabled"; }; + + gpio0: gpio@e8a0b000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a0b000 0 0x1000>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 1 0 7>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO0>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio1: gpio@e8a0c000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a0c000 0 0x1000>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 1 7 7>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO1>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio2: gpio@e8a0d000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a0d000 0 0x1000>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 14 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO2>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio3: gpio@e8a0e000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a0e000 0 0x1000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 22 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO3>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio4: gpio@e8a0f000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a0f000 0 0x1000>; + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 30 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO4>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio5: gpio@e8a10000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a10000 0 0x1000>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 38 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO5>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio6: gpio@e8a11000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a11000 0 0x1000>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 46 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO6>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio7: gpio@e8a12000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a12000 0 0x1000>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 54 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO7>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio8: gpio@e8a13000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a13000 0 0x1000>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 62 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO8>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio9: gpio@e8a14000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a14000 0 0x1000>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 70 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO9>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio10: gpio@e8a15000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a15000 0 0x1000>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 78 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO10>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio11: gpio@e8a16000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a16000 0 0x1000>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 86 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO11>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio12: gpio@e8a17000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a17000 0 0x1000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 94 3 &pmx0 7 101 1>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO12>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio13: gpio@e8a18000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a18000 0 0x1000>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 102 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO13>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio14: gpio@e8a19000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a19000 0 0x1000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 110 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO14>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio15: gpio@e8a1a000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a1a000 0 0x1000>; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx0 0 118 6>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO15>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio16: gpio@e8a1b000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a1b000 0 0x1000>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO16>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio17: gpio@e8a1c000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a1c000 0 0x1000>; + interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO17>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio18: gpio@ff3b4000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xff3b4000 0 0x1000>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx2 0 0 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO18>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio19: gpio@ff3b5000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xff3b5000 0 0x1000>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx2 0 8 4>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO19>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio20: gpio@e8a1f000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a1f000 0 0x1000>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pmx1 0 0 6>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO20>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio21: gpio@e8a20000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xe8a20000 0 0x1000>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&pmx3 0 0 6>; + clocks = <&crg_ctrl HI3660_PCLK_GPIO21>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio22: gpio@fff0b000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xfff0b000 0 0x1000>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + /* GPIO176 */ + gpio-ranges = <&pmx4 2 0 6>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&sctrl HI3660_PCLK_AO_GPIO0>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio23: gpio@fff0c000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xfff0c000 0 0x1000>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + /* GPIO184 */ + gpio-ranges = <&pmx4 0 6 7>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&sctrl HI3660_PCLK_AO_GPIO1>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio24: gpio@fff0d000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xfff0d000 0 0x1000>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + /* GPIO192 */ + gpio-ranges = <&pmx4 0 13 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&sctrl HI3660_PCLK_AO_GPIO2>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio25: gpio@fff0e000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xfff0e000 0 0x1000>; + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + /* GPIO200 */ + gpio-ranges = <&pmx4 0 21 4 &pmx4 5 25 3>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&sctrl HI3660_PCLK_AO_GPIO3>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio26: gpio@fff0f000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xfff0f000 0 0x1000>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + /* GPIO208 */ + gpio-ranges = <&pmx4 0 28 8>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&sctrl HI3660_PCLK_AO_GPIO4>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio27: gpio@fff10000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xfff10000 0 0x1000>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + /* GPIO216 */ + gpio-ranges = <&pmx4 0 36 6>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&sctrl HI3660_PCLK_AO_GPIO5>; + clock-names = "apb_pclk"; + status = "ok"; + }; + + gpio28: gpio@fff1d000 { + compatible = "arm,pl061", "arm,primecell"; + reg = <0 0xfff1d000 0 0x1000>; + interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&sctrl HI3660_PCLK_AO_GPIO6>; + clock-names = "apb_pclk"; + status = "ok"; + }; }; };