| Message ID | 20170419091326.11226-5-linus.walleij@linaro.org |
|---|---|
| State | New |
| Headers | show |
| Series | None | expand |
On Wed 19 Apr 02:13 PDT 2017, Linus Walleij wrote: > diff --git a/drivers/clk/qcom/lcc-msm8660.c b/drivers/clk/qcom/lcc-msm8660.c [..] > +/* The vendor code uses PLL4 as parent everywhere */ > +static const struct parent_map lcc_parent_map[] = { > + { P_PXO, 0 }, > + { P_CXO, 1 }, > + /* Select RPM PLL4, but also used for selecting LPA PLL0 */ > + { P_PLL4_LPA_PLL0, 2 }, > + /* Will just ground the line */ > + { P_GND, 6 }, > +}; > + > +static const char * const lcc_parent_tbl[] = { > + "pxo", > + "cxo", > + /* > + * PLL4 is an RPM clock on MSM8660/APQ8060, set to "pll4" for this > + * If we enable and mux in the LPA_PLL0 on this platform, we can > + * set this to "lpa_pll0" instead > + */ > + "pll4_clk", > + "gnd", /* This is a very inactive parent */ > +}; > + > +/* > + * This table is evidently for using PLL4 as parent, if we start using > + * LPA_PLL0 we need to provide a second table. > + */ Aren't you muxing in LPA_PLL0 as source instead of PLL4 at the bottom of probe()? And as you hard code that selector, shouldn't the parent table reference lpa_pll0? > +static struct freq_tbl clk_tbl_aif_osr_pll4[] = { > + { 768000, P_PLL4_LPA_PLL0, 4, 1, 176 }, > + { 1024000, P_PLL4_LPA_PLL0, 4, 1, 132 }, > + { 1536000, P_PLL4_LPA_PLL0, 4, 1, 88 }, > + { 2048000, P_PLL4_LPA_PLL0, 4, 1, 66 }, > + { 3072000, P_PLL4_LPA_PLL0, 4, 1, 44 }, > + { 4096000, P_PLL4_LPA_PLL0, 4, 1, 33 }, > + { 6144000, P_PLL4_LPA_PLL0, 4, 1, 22 }, > + { 8192000, P_PLL4_LPA_PLL0, 2, 1, 33 }, > + { 12288000, P_PLL4_LPA_PLL0, 4, 1, 11 }, > + { 24576000, P_PLL4_LPA_PLL0, 2, 1, 11 }, > + { 27000000, P_PXO, 1, 0, 0 }, > + { } > +}; > + [..] > +static int lcc_msm8660_probe(struct platform_device *pdev) > +{ [..] > + /* > + * Enable LPA_PLL0 source on the LPASS Primary PLL Mux. Incidentally > + * this is set to 0x00000001 at boot. > + * 0x01 = LPA_PLL0 > + */ > + regmap_write(regmap, 0xc4, 0x1); Regards, Bjorn -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Sat, May 27, 2017 at 10:19 PM, Bjorn Andersson <bjorn.andersson@linaro.org> wrote: > On Wed 19 Apr 02:13 PDT 2017, Linus Walleij wrote: >> diff --git a/drivers/clk/qcom/lcc-msm8660.c b/drivers/clk/qcom/lcc-msm8660.c > [..] >> +/* The vendor code uses PLL4 as parent everywhere */ >> +static const struct parent_map lcc_parent_map[] = { >> + { P_PXO, 0 }, >> + { P_CXO, 1 }, >> + /* Select RPM PLL4, but also used for selecting LPA PLL0 */ >> + { P_PLL4_LPA_PLL0, 2 }, >> + /* Will just ground the line */ >> + { P_GND, 6 }, >> +}; >> + >> +static const char * const lcc_parent_tbl[] = { >> + "pxo", >> + "cxo", >> + /* >> + * PLL4 is an RPM clock on MSM8660/APQ8060, set to "pll4" for this >> + * If we enable and mux in the LPA_PLL0 on this platform, we can >> + * set this to "lpa_pll0" instead >> + */ >> + "pll4_clk", >> + "gnd", /* This is a very inactive parent */ >> +}; >> + >> +/* >> + * This table is evidently for using PLL4 as parent, if we start using >> + * LPA_PLL0 we need to provide a second table. >> + */ > > Aren't you muxing in LPA_PLL0 as source instead of PLL4 at the bottom of > probe()? And as you hard code that selector, shouldn't the parent table > reference lpa_pll0? I think it's just a naming problem. I'm actually using: >> + { 768000, P_PLL4_LPA_PLL0, 4, 1, 176 }, Because as far as I can tell, RPM clock PLL4 and LPA_PLL0 is the same thing, just different names. I don't think the 8660 has its own LPA PLL, it's just the layers of confusion in the code that make it seem like so. Or maybe someone was in the planning stages of adding the LPA PLL to the hardware and never got there. So some code confusingly refers to that... I would really like to see how it actually works. BTW: do you have a pointer to a vendor tree for a Sony thing using the MSM8660 or APQ8060 that I can look at? I need more known working code to inspect. Yours, Linus Walleij -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Mon 29 May 05:23 PDT 2017, Linus Walleij wrote: > On Sat, May 27, 2017 at 10:19 PM, Bjorn Andersson > <bjorn.andersson@linaro.org> wrote: > > On Wed 19 Apr 02:13 PDT 2017, Linus Walleij wrote: > >> diff --git a/drivers/clk/qcom/lcc-msm8660.c b/drivers/clk/qcom/lcc-msm8660.c > > [..] > >> +/* The vendor code uses PLL4 as parent everywhere */ > >> +static const struct parent_map lcc_parent_map[] = { > >> + { P_PXO, 0 }, > >> + { P_CXO, 1 }, > >> + /* Select RPM PLL4, but also used for selecting LPA PLL0 */ > >> + { P_PLL4_LPA_PLL0, 2 }, > >> + /* Will just ground the line */ > >> + { P_GND, 6 }, > >> +}; > >> + > >> +static const char * const lcc_parent_tbl[] = { > >> + "pxo", > >> + "cxo", > >> + /* > >> + * PLL4 is an RPM clock on MSM8660/APQ8060, set to "pll4" for this > >> + * If we enable and mux in the LPA_PLL0 on this platform, we can > >> + * set this to "lpa_pll0" instead > >> + */ > >> + "pll4_clk", > >> + "gnd", /* This is a very inactive parent */ > >> +}; > >> + > >> +/* > >> + * This table is evidently for using PLL4 as parent, if we start using > >> + * LPA_PLL0 we need to provide a second table. > >> + */ > > > > Aren't you muxing in LPA_PLL0 as source instead of PLL4 at the bottom of > > probe()? And as you hard code that selector, shouldn't the parent table > > reference lpa_pll0? > > I think it's just a naming problem. > > I'm actually using: > > >> + { 768000, P_PLL4_LPA_PLL0, 4, 1, 176 }, > > Because as far as I can tell, RPM clock PLL4 and LPA_PLL0 is the > same thing, just different names. > > I don't think the 8660 has its own LPA PLL, it's just the layers of > confusion in the code that make it seem like so. > > Or maybe someone was in the planning stages of adding the LPA PLL > to the hardware and never got there. So some code confusingly > refers to that... > > I would really like to see how it actually works. > 8660 and 8960 are basically different revisions of the same SoC, so reviewing clock-8x60.c and clock-8960.c found in below repository gives some additional insight. clock-8x60.c mentions LPA_PLL0 in _one_ comment and carries the definitions for a LCC_PLL0 clock, but no references are made to these defines. The code ever only references "pll4". clock-8960.c goes beyond this and actually reference the LCC_PLL0 registers and they are all used to query and configure "pll4". So AFAICT PLL4 is controlled/implemented in the LCC block and is called PLL0 in that context and that on 8660 it's completely controlled by the RPM. As such I think it makes sense - on 8660 - to just reference "pll4", perhaps with some comment in the code referencing LCC_PLL0 as the actual implementation. > BTW: do you have a pointer to a vendor tree for a Sony thing using > the MSM8660 or APQ8060 that I can look at? I need more known > working code to inspect. > The tree I used for AOSP work on Xperia S can be found here: https://github.com/sonyxperiadev/kernel/tree/nozomi/M8260AAABQNLZA30145 Regards, Bjorn -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 05/30, Bjorn Andersson wrote: > On Mon 29 May 05:23 PDT 2017, Linus Walleij wrote: > > > On Sat, May 27, 2017 at 10:19 PM, Bjorn Andersson > > <bjorn.andersson@linaro.org> wrote: > > > On Wed 19 Apr 02:13 PDT 2017, Linus Walleij wrote: > > >> diff --git a/drivers/clk/qcom/lcc-msm8660.c b/drivers/clk/qcom/lcc-msm8660.c > > > [..] > > >> +/* The vendor code uses PLL4 as parent everywhere */ > > >> +static const struct parent_map lcc_parent_map[] = { > > >> + { P_PXO, 0 }, > > >> + { P_CXO, 1 }, > > >> + /* Select RPM PLL4, but also used for selecting LPA PLL0 */ > > >> + { P_PLL4_LPA_PLL0, 2 }, > > >> + /* Will just ground the line */ > > >> + { P_GND, 6 }, > > >> +}; > > >> + > > >> +static const char * const lcc_parent_tbl[] = { > > >> + "pxo", > > >> + "cxo", > > >> + /* > > >> + * PLL4 is an RPM clock on MSM8660/APQ8060, set to "pll4" for this > > >> + * If we enable and mux in the LPA_PLL0 on this platform, we can > > >> + * set this to "lpa_pll0" instead > > >> + */ > > >> + "pll4_clk", > > >> + "gnd", /* This is a very inactive parent */ > > >> +}; > > >> + > > >> +/* > > >> + * This table is evidently for using PLL4 as parent, if we start using > > >> + * LPA_PLL0 we need to provide a second table. > > >> + */ > > > > > > Aren't you muxing in LPA_PLL0 as source instead of PLL4 at the bottom of > > > probe()? And as you hard code that selector, shouldn't the parent table > > > reference lpa_pll0? > > > > I think it's just a naming problem. > > > > I'm actually using: > > > > >> + { 768000, P_PLL4_LPA_PLL0, 4, 1, 176 }, > > > > Because as far as I can tell, RPM clock PLL4 and LPA_PLL0 is the > > same thing, just different names. > > > > I don't think the 8660 has its own LPA PLL, it's just the layers of > > confusion in the code that make it seem like so. > > > > Or maybe someone was in the planning stages of adding the LPA PLL > > to the hardware and never got there. So some code confusingly > > refers to that... > > > > I would really like to see how it actually works. > > > > 8660 and 8960 are basically different revisions of the same SoC, so > reviewing clock-8x60.c and clock-8960.c found in below repository gives > some additional insight. > > clock-8x60.c mentions LPA_PLL0 in _one_ comment and carries the > definitions for a LCC_PLL0 clock, but no references are made to these > defines. The code ever only references "pll4". > > clock-8960.c goes beyond this and actually reference the LCC_PLL0 > registers and they are all used to query and configure "pll4". > > > So AFAICT PLL4 is controlled/implemented in the LCC block and is called > PLL0 in that context and that on 8660 it's completely controlled by the > RPM. > > As such I think it makes sense - on 8660 - to just reference "pll4", > perhaps with some comment in the code referencing LCC_PLL0 as the actual > implementation. Correct, LCC_PLL0 is a local naming scheme for the audio clock controller's 0th PLL. That just so happens to be PLL4 "globally" in the SoC. From global clock control standpoint it's PLL4. I would just reference PLL4 everywhere and ignore the whole LCC_PLL0 thing. -- Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 04/19, Linus Walleij wrote: > This adds support for the MSM8660 Low-power audio > subsystem (LPASS) clock controller (LCC). This is nice when > you want to have audio from the system. > > We currently only support using the PLL4 (which is an RPM > clock) as the parent, however the LPASS has its own PLL named > LPA_PLL0 that we can experiment with enabling later on, so > for this reason the code contains a few hints on how to enable > the LPA_PLL0. > > Signed-off-by: Linus Walleij <linus.walleij@linaro.org> > --- > ChangeLog v1->v2: > - No changes. > --- > drivers/clk/qcom/Kconfig | 9 + > drivers/clk/qcom/Makefile | 1 + > drivers/clk/qcom/lcc-msm8660.c | 418 +++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 428 insertions(+) > create mode 100644 drivers/clk/qcom/lcc-msm8660.c > > diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig > index 5fb8d7430908..d657d94d372f 100644 > --- a/drivers/clk/qcom/Kconfig > +++ b/drivers/clk/qcom/Kconfig > @@ -90,6 +90,15 @@ config MSM_GCC_8660 > Say Y if you want to use peripheral devices such as UART, SPI, > i2c, USB, SD/eMMC, etc. > > +config MSM_LCC_8660 > + tristate "MSM8660 LPASS Clock Controller" > + select MSM_GCC_8660 > + depends on COMMON_CLK_QCOM depends on MSM_GCC_8660? Or perhaps the RPM driver. The intent is to make sure the driver can't be built unless the dependency clks that are inputs to the controller are also built. We may want to just get rid of that sort of dependency, but that's the design right now. > + help > + Support for the Low-power Audio Subsystem (LPASS) clock controller > + on MSM8660 devices. > + Say Y if you want to use audio devices such as I2S and PCM. > + > config MSM_GCC_8916 > tristate "MSM8916 Global Clock Controller" > select QCOM_GDSC > diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile > index 1c3e222b917b..d6d5ab178522 100644 > --- a/drivers/clk/qcom/Makefile > +++ b/drivers/clk/qcom/Makefile > @@ -21,6 +21,7 @@ obj-$(CONFIG_IPQ_LCC_806X) += lcc-ipq806x.o > obj-$(CONFIG_MDM_GCC_9615) += gcc-mdm9615.o > obj-$(CONFIG_MDM_LCC_9615) += lcc-mdm9615.o > obj-$(CONFIG_MSM_GCC_8660) += gcc-msm8660.o > +obj-$(CONFIG_MSM_LCC_8660) += lcc-msm8660.o > obj-$(CONFIG_MSM_GCC_8916) += gcc-msm8916.o > obj-$(CONFIG_MSM_GCC_8960) += gcc-msm8960.o > obj-$(CONFIG_MSM_GCC_8974) += gcc-msm8974.o > diff --git a/drivers/clk/qcom/lcc-msm8660.c b/drivers/clk/qcom/lcc-msm8660.c > new file mode 100644 > index 000000000000..73dc8ede6a2a > --- /dev/null > +++ b/drivers/clk/qcom/lcc-msm8660.c > @@ -0,0 +1,418 @@ > +/* > + * Qualcomm MSM8660/APQ8060 Low-power Audio Subsystem (LPASS) Clock Controller > + * Copyright (c) 2017 Linus Walleij <linus.walleij@linaro.org> > + * > + * Based on a copy of the IPQ806x driver > + * (C) 2014 Rajendra Nayak I don't see that in the file. Perhaps you meant to copy the linux foundation one like in mdm9615? > + * and portions of the MDM9615 driver > + * (C) 2014 Neil Armstrong. > + */ > + > +#include <linux/kernel.h> > +#include <linux/bitops.h> > +#include <linux/err.h> > +#include <linux/platform_device.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/of_device.h> Is this used? > +#include <linux/clk-provider.h> > +#include <linux/regmap.h> > + > +#include <dt-bindings/clock/qcom,lcc-msm8660.h> > + > +#include "common.h" > +#include "clk-regmap.h" > +#include "clk-pll.h" > +#include "clk-rcg.h" > +#include "clk-branch.h" > +#include "clk-regmap-divider.h" > +#include "clk-regmap-mux.h" > + > +/* > + * The vendor tree calls this "PLL0" but we are going to refer to it as > + * LPA_PLL0 so as not to confuse it with the PLL0 on the GCC. > + */ > +static struct clk_pll lpa_pll0 = { > + .l_reg = 0x4, > + .m_reg = 0x8, > + .n_reg = 0xc, > + .config_reg = 0x14, > + .mode_reg = 0x0, > + .status_reg = 0x18, > + .status_bit = 16, > + .clkr.hw.init = &(struct clk_init_data){ > + .name = "lpa_pll0", Just PLL4 please. > + .parent_names = (const char *[]){ "pxo" }, > + .num_parents = 1, > + .ops = &clk_pll_ops, > + }, > +}; > + > +/* > + * The l/m/n values were read out of the registers after a cold boot. > + * The config register read 00c22080 and the mode register 0x00000007. 0x00c22080? > + */ > +static const struct pll_config lpa_pll0_config = { > + .l = 0xf, > + .m = 0x1c, > + .n = 0x465, > + .vco_val = BIT(17), > + .vco_mask = BIT(17) | BIT(16), > + .pre_div_val = 0x0, > + .pre_div_mask = BIT(19), > + .post_div_val = 0x0, > + .post_div_mask = BIT(21) | BIT(20), > + .mn_ena_mask = BIT(22), > + .main_output_mask = BIT(23), > +}; > + > +enum { > + P_PXO, > + P_CXO, > + P_PLL4_LPA_PLL0, Just call it P_PLL4 please. > + P_GND, Please remove ground. > +}; > + > +/* The vendor code uses PLL4 as parent everywhere */ > +static const struct parent_map lcc_parent_map[] = { > + { P_PXO, 0 }, > + { P_CXO, 1 }, > + /* Select RPM PLL4, but also used for selecting LPA PLL0 */ > + { P_PLL4_LPA_PLL0, 2 }, > + /* Will just ground the line */ > + { P_GND, 6 }, We don't do clk grounding upstream so we don't need this. We can add grounding in the future if anyone cares. > +}; > + > +static const char * const lcc_parent_tbl[] = { > + "pxo", > + "cxo", > + /* > + * PLL4 is an RPM clock on MSM8660/APQ8060, set to "pll4" for this > + * If we enable and mux in the LPA_PLL0 on this platform, we can > + * set this to "lpa_pll0" instead This comment is confusing because PLL4 is LPA_PLL0. > + */ > + "pll4_clk", And just pll4. We don't need _clk for that. If that affects RPM driver, it should be fixed as well. > + "gnd", /* This is a very inactive parent */ Heh. Is it needed because an audio clk is set to ground by default? That's the only case where I think it may be needed, but I don't think we have that case where we need to change the parent from ground to something else. If so, then we'll need to add it as a valid source and then register it in this driver as a fixed rate clk of rate 0. > +}; > + > +/* > + * This table is evidently for using PLL4 as parent, if we start using > + * LPA_PLL0 we need to provide a second table. > + */ Remove comment. > +static struct freq_tbl clk_tbl_aif_osr_pll4[] = { > + { 768000, P_PLL4_LPA_PLL0, 4, 1, 176 }, > + { 1024000, P_PLL4_LPA_PLL0, 4, 1, 132 }, > + { 1536000, P_PLL4_LPA_PLL0, 4, 1, 88 }, > + { 2048000, P_PLL4_LPA_PLL0, 4, 1, 66 }, > + { 3072000, P_PLL4_LPA_PLL0, 4, 1, 44 }, > + { 4096000, P_PLL4_LPA_PLL0, 4, 1, 33 }, > + { 6144000, P_PLL4_LPA_PLL0, 4, 1, 22 }, > + { 8192000, P_PLL4_LPA_PLL0, 2, 1, 33 }, > + { 12288000, P_PLL4_LPA_PLL0, 4, 1, 11 }, > + { 24576000, P_PLL4_LPA_PLL0, 2, 1, 11 }, > + { 27000000, P_PXO, 1, 0, 0 }, > + { } > +}; > + > +/* > + * This macro is modified from lcc-mdm9516.c, it's used for all the > + * AIF clocks, all of them have an OSR clock and a bit clock derived > + * from the OSR clock. > + * > + * These clocks differ from many other platforms by using > + * BRANCH_HALT_DELAY for the *_bit_div_clk > + */ Ok. Please leave out this comment. > +#define CLK_AIF_OSR_DIV(prefix, _ns, _md, _hr) \ > +static struct clk_rcg prefix##_osr_src = { \ > + .ns_reg = _ns, \ > + .md_reg = _md, \ > + .mn = { \ > + .mnctr_en_bit = 8, \ > + .mnctr_reset_bit = 7, \ > + .mnctr_mode_shift = 5, \ > + .n_val_shift = 24, \ > + .m_val_shift = 8, \ > + .width = 8, \ > + }, \ > + .p = { \ > + .pre_div_shift = 3, \ > + .pre_div_width = 2, \ > + }, \ > + .s = { \ > + .src_sel_shift = 0, \ > + .parent_map = lcc_parent_map, \ > + }, \ > + .freq_tbl = clk_tbl_aif_osr_pll4, \ > + .clkr = { \ > + .enable_reg = _ns, \ > + .enable_mask = BIT(9), \ > + .hw.init = &(struct clk_init_data){ \ > + .name = #prefix "_osr_src", \ > + .parent_names = lcc_parent_tbl, \ > + .num_parents = 4, \ > + .ops = &clk_rcg_ops, \ > + .flags = CLK_SET_RATE_GATE, \ > + }, \ > + }, \ > +}; \ > + \ > +static const char * const lcc_##prefix##_parents[] = { \ > + #prefix "_osr_src", \ > +}; \ > + \ > +static struct clk_branch prefix##_osr_clk = { \ > + .halt_reg = _hr, \ > + .halt_bit = 1, \ > + .halt_check = BRANCH_HALT_ENABLE, \ > + .clkr = { \ > + .enable_reg = _ns, \ > + .enable_mask = BIT(17), \ > + .hw.init = &(struct clk_init_data){ \ > + .name = #prefix "_osr_clk", \ > + .parent_names = lcc_##prefix##_parents, \ > + .num_parents = 1, \ > + .ops = &clk_branch_ops, \ > + .flags = CLK_SET_RATE_PARENT, \ > + }, \ > + }, \ > +}; \ > + \ > +static struct clk_regmap_div prefix##_div_clk = { \ > + .reg = _ns, \ > + .shift = 10, \ > + .width = 4, \ > + .clkr = { \ > + .hw.init = &(struct clk_init_data){ \ > + .name = #prefix "_div_clk", \ > + .parent_names = lcc_##prefix##_parents, \ > + .num_parents = 1, \ > + .ops = &clk_regmap_div_ops, \ > + }, \ > + }, \ > +}; \ > + \ > +static struct clk_branch prefix##_bit_div_clk = { \ > + .halt_reg = _hr, \ > + .halt_bit = 0, \ > + .halt_check = BRANCH_HALT_DELAY, \ > + .clkr = { \ > + .enable_reg = _ns, \ > + .enable_mask = BIT(15), \ > + .hw.init = &(struct clk_init_data){ \ > + .name = #prefix "_bit_div_clk", \ > + .parent_names = (const char *[]){ \ > + #prefix "_div_clk" \ > + }, \ > + .num_parents = 1, \ > + .ops = &clk_branch_ops, \ > + .flags = CLK_SET_RATE_PARENT, \ > + }, \ > + }, \ > +}; \ > + \ > +static struct clk_regmap_mux prefix##_bit_clk = { \ > + .reg = _ns, \ > + .shift = 14, \ > + .width = 1, \ > + .clkr = { \ > + .hw.init = &(struct clk_init_data){ \ > + .name = #prefix "_bit_clk", \ > + .parent_names = (const char *[]){ \ > + #prefix "_bit_div_clk", \ > + #prefix "_codec_clk", \ > + }, \ > + .num_parents = 2, \ > + .ops = &clk_regmap_mux_closest_ops, \ > + .flags = CLK_SET_RATE_PARENT, \ > + }, \ > + }, \ > +} > + > +CLK_AIF_OSR_DIV(mi2s, 0x48, 0x4c, 0x50); > +CLK_AIF_OSR_DIV(codec_i2s_mic, 0x60, 0x64, 0x68); > +CLK_AIF_OSR_DIV(spare_i2s_mic, 0x78, 0x7c, 0x80); > +CLK_AIF_OSR_DIV(codec_i2s_spkr, 0x6c, 0x70, 0x74); > +CLK_AIF_OSR_DIV(spare_i2s_spkr, 0x84, 0x88, 0x8c); > + > +/* > + * PCM clock > + * This table is evidently for using PLL4 as parent, if we start using > + * LPA_PLL0 we need to provide a second table. > + */ Remove comment. > +static struct freq_tbl clk_tbl_pcm_pll4[] = { > + { 512000, P_PLL4_LPA_PLL0, 4, 1, 264 }, > + { 768000, P_PLL4_LPA_PLL0, 4, 1, 176 }, > + { 1024000, P_PLL4_LPA_PLL0, 4, 1, 132 }, > + { 1536000, P_PLL4_LPA_PLL0, 4, 1, 88 }, > + { 2048000, P_PLL4_LPA_PLL0, 4, 1, 66 }, > + { 3072000, P_PLL4_LPA_PLL0, 4, 1, 44 }, > + { 4096000, P_PLL4_LPA_PLL0, 4, 1, 33 }, > + { 6144000, P_PLL4_LPA_PLL0, 4, 1, 22 }, > + { 8192000, P_PLL4_LPA_PLL0, 2, 1, 33 }, > + { 12288000, P_PLL4_LPA_PLL0, 4, 1, 11 }, > + { 24580000, P_PLL4_LPA_PLL0, 2, 1, 11 }, > + { 27000000, P_PXO, 1, 0, 0 }, > + { }, > +}; [...] > + > +static int lcc_msm8660_probe(struct platform_device *pdev) > +{ > + u32 val; > + struct regmap *regmap; > + > + regmap = qcom_cc_map(pdev, &lcc_msm8660_desc); > + if (IS_ERR(regmap)) > + return PTR_ERR(regmap); > + > + /* Configure the rate of LPA_PLL0 if the bootloader hasn't already */ > + regmap_read(regmap, 0x0, &val); > + if (!val) { > + dev_info(&pdev->dev, "configuring LPA_PLL0\n"); > + clk_pll_configure_sr(&lpa_pll0, regmap, &lpa_pll0_config, true); > + } else { > + dev_info(&pdev->dev, > + "LPA_PLL0 already configured\n"); dev_dbg? Is this the case that happens for you? I don't think we should be programming the hardware because the RPM controls the PLL. It should already be setup to the right rate. I don't see this happening in the downstream code either, so this should all be removed most likely. > + } > + > + /* > + * Enable LPA_PLL0 source on the LPASS Primary PLL Mux. Incidentally > + * this is set to 0x00000001 at boot. > + * 0x01 = LPA_PLL0 > + */ > + regmap_write(regmap, 0xc4, 0x1); And this isn't needed either? > + > + return qcom_cc_really_probe(pdev, &lcc_msm8660_desc, regmap); > +} > + -- Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, a Linux Foundation Collaborative Project -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig index 5fb8d7430908..d657d94d372f 100644 --- a/drivers/clk/qcom/Kconfig +++ b/drivers/clk/qcom/Kconfig @@ -90,6 +90,15 @@ config MSM_GCC_8660 Say Y if you want to use peripheral devices such as UART, SPI, i2c, USB, SD/eMMC, etc. +config MSM_LCC_8660 + tristate "MSM8660 LPASS Clock Controller" + select MSM_GCC_8660 + depends on COMMON_CLK_QCOM + help + Support for the Low-power Audio Subsystem (LPASS) clock controller + on MSM8660 devices. + Say Y if you want to use audio devices such as I2S and PCM. + config MSM_GCC_8916 tristate "MSM8916 Global Clock Controller" select QCOM_GDSC diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile index 1c3e222b917b..d6d5ab178522 100644 --- a/drivers/clk/qcom/Makefile +++ b/drivers/clk/qcom/Makefile @@ -21,6 +21,7 @@ obj-$(CONFIG_IPQ_LCC_806X) += lcc-ipq806x.o obj-$(CONFIG_MDM_GCC_9615) += gcc-mdm9615.o obj-$(CONFIG_MDM_LCC_9615) += lcc-mdm9615.o obj-$(CONFIG_MSM_GCC_8660) += gcc-msm8660.o +obj-$(CONFIG_MSM_LCC_8660) += lcc-msm8660.o obj-$(CONFIG_MSM_GCC_8916) += gcc-msm8916.o obj-$(CONFIG_MSM_GCC_8960) += gcc-msm8960.o obj-$(CONFIG_MSM_GCC_8974) += gcc-msm8974.o diff --git a/drivers/clk/qcom/lcc-msm8660.c b/drivers/clk/qcom/lcc-msm8660.c new file mode 100644 index 000000000000..73dc8ede6a2a --- /dev/null +++ b/drivers/clk/qcom/lcc-msm8660.c @@ -0,0 +1,418 @@ +/* + * Qualcomm MSM8660/APQ8060 Low-power Audio Subsystem (LPASS) Clock Controller + * Copyright (c) 2017 Linus Walleij <linus.walleij@linaro.org> + * + * Based on a copy of the IPQ806x driver + * (C) 2014 Rajendra Nayak + * and portions of the MDM9615 driver + * (C) 2014 Neil Armstrong. + */ + +#include <linux/kernel.h> +#include <linux/bitops.h> +#include <linux/err.h> +#include <linux/platform_device.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/clk-provider.h> +#include <linux/regmap.h> + +#include <dt-bindings/clock/qcom,lcc-msm8660.h> + +#include "common.h" +#include "clk-regmap.h" +#include "clk-pll.h" +#include "clk-rcg.h" +#include "clk-branch.h" +#include "clk-regmap-divider.h" +#include "clk-regmap-mux.h" + +/* + * The vendor tree calls this "PLL0" but we are going to refer to it as + * LPA_PLL0 so as not to confuse it with the PLL0 on the GCC. + */ +static struct clk_pll lpa_pll0 = { + .l_reg = 0x4, + .m_reg = 0x8, + .n_reg = 0xc, + .config_reg = 0x14, + .mode_reg = 0x0, + .status_reg = 0x18, + .status_bit = 16, + .clkr.hw.init = &(struct clk_init_data){ + .name = "lpa_pll0", + .parent_names = (const char *[]){ "pxo" }, + .num_parents = 1, + .ops = &clk_pll_ops, + }, +}; + +/* + * The l/m/n values were read out of the registers after a cold boot. + * The config register read 00c22080 and the mode register 0x00000007. + */ +static const struct pll_config lpa_pll0_config = { + .l = 0xf, + .m = 0x1c, + .n = 0x465, + .vco_val = BIT(17), + .vco_mask = BIT(17) | BIT(16), + .pre_div_val = 0x0, + .pre_div_mask = BIT(19), + .post_div_val = 0x0, + .post_div_mask = BIT(21) | BIT(20), + .mn_ena_mask = BIT(22), + .main_output_mask = BIT(23), +}; + +enum { + P_PXO, + P_CXO, + P_PLL4_LPA_PLL0, + P_GND, +}; + +/* The vendor code uses PLL4 as parent everywhere */ +static const struct parent_map lcc_parent_map[] = { + { P_PXO, 0 }, + { P_CXO, 1 }, + /* Select RPM PLL4, but also used for selecting LPA PLL0 */ + { P_PLL4_LPA_PLL0, 2 }, + /* Will just ground the line */ + { P_GND, 6 }, +}; + +static const char * const lcc_parent_tbl[] = { + "pxo", + "cxo", + /* + * PLL4 is an RPM clock on MSM8660/APQ8060, set to "pll4" for this + * If we enable and mux in the LPA_PLL0 on this platform, we can + * set this to "lpa_pll0" instead + */ + "pll4_clk", + "gnd", /* This is a very inactive parent */ +}; + +/* + * This table is evidently for using PLL4 as parent, if we start using + * LPA_PLL0 we need to provide a second table. + */ +static struct freq_tbl clk_tbl_aif_osr_pll4[] = { + { 768000, P_PLL4_LPA_PLL0, 4, 1, 176 }, + { 1024000, P_PLL4_LPA_PLL0, 4, 1, 132 }, + { 1536000, P_PLL4_LPA_PLL0, 4, 1, 88 }, + { 2048000, P_PLL4_LPA_PLL0, 4, 1, 66 }, + { 3072000, P_PLL4_LPA_PLL0, 4, 1, 44 }, + { 4096000, P_PLL4_LPA_PLL0, 4, 1, 33 }, + { 6144000, P_PLL4_LPA_PLL0, 4, 1, 22 }, + { 8192000, P_PLL4_LPA_PLL0, 2, 1, 33 }, + { 12288000, P_PLL4_LPA_PLL0, 4, 1, 11 }, + { 24576000, P_PLL4_LPA_PLL0, 2, 1, 11 }, + { 27000000, P_PXO, 1, 0, 0 }, + { } +}; + +/* + * This macro is modified from lcc-mdm9516.c, it's used for all the + * AIF clocks, all of them have an OSR clock and a bit clock derived + * from the OSR clock. + * + * These clocks differ from many other platforms by using + * BRANCH_HALT_DELAY for the *_bit_div_clk + */ +#define CLK_AIF_OSR_DIV(prefix, _ns, _md, _hr) \ +static struct clk_rcg prefix##_osr_src = { \ + .ns_reg = _ns, \ + .md_reg = _md, \ + .mn = { \ + .mnctr_en_bit = 8, \ + .mnctr_reset_bit = 7, \ + .mnctr_mode_shift = 5, \ + .n_val_shift = 24, \ + .m_val_shift = 8, \ + .width = 8, \ + }, \ + .p = { \ + .pre_div_shift = 3, \ + .pre_div_width = 2, \ + }, \ + .s = { \ + .src_sel_shift = 0, \ + .parent_map = lcc_parent_map, \ + }, \ + .freq_tbl = clk_tbl_aif_osr_pll4, \ + .clkr = { \ + .enable_reg = _ns, \ + .enable_mask = BIT(9), \ + .hw.init = &(struct clk_init_data){ \ + .name = #prefix "_osr_src", \ + .parent_names = lcc_parent_tbl, \ + .num_parents = 4, \ + .ops = &clk_rcg_ops, \ + .flags = CLK_SET_RATE_GATE, \ + }, \ + }, \ +}; \ + \ +static const char * const lcc_##prefix##_parents[] = { \ + #prefix "_osr_src", \ +}; \ + \ +static struct clk_branch prefix##_osr_clk = { \ + .halt_reg = _hr, \ + .halt_bit = 1, \ + .halt_check = BRANCH_HALT_ENABLE, \ + .clkr = { \ + .enable_reg = _ns, \ + .enable_mask = BIT(17), \ + .hw.init = &(struct clk_init_data){ \ + .name = #prefix "_osr_clk", \ + .parent_names = lcc_##prefix##_parents, \ + .num_parents = 1, \ + .ops = &clk_branch_ops, \ + .flags = CLK_SET_RATE_PARENT, \ + }, \ + }, \ +}; \ + \ +static struct clk_regmap_div prefix##_div_clk = { \ + .reg = _ns, \ + .shift = 10, \ + .width = 4, \ + .clkr = { \ + .hw.init = &(struct clk_init_data){ \ + .name = #prefix "_div_clk", \ + .parent_names = lcc_##prefix##_parents, \ + .num_parents = 1, \ + .ops = &clk_regmap_div_ops, \ + }, \ + }, \ +}; \ + \ +static struct clk_branch prefix##_bit_div_clk = { \ + .halt_reg = _hr, \ + .halt_bit = 0, \ + .halt_check = BRANCH_HALT_DELAY, \ + .clkr = { \ + .enable_reg = _ns, \ + .enable_mask = BIT(15), \ + .hw.init = &(struct clk_init_data){ \ + .name = #prefix "_bit_div_clk", \ + .parent_names = (const char *[]){ \ + #prefix "_div_clk" \ + }, \ + .num_parents = 1, \ + .ops = &clk_branch_ops, \ + .flags = CLK_SET_RATE_PARENT, \ + }, \ + }, \ +}; \ + \ +static struct clk_regmap_mux prefix##_bit_clk = { \ + .reg = _ns, \ + .shift = 14, \ + .width = 1, \ + .clkr = { \ + .hw.init = &(struct clk_init_data){ \ + .name = #prefix "_bit_clk", \ + .parent_names = (const char *[]){ \ + #prefix "_bit_div_clk", \ + #prefix "_codec_clk", \ + }, \ + .num_parents = 2, \ + .ops = &clk_regmap_mux_closest_ops, \ + .flags = CLK_SET_RATE_PARENT, \ + }, \ + }, \ +} + +CLK_AIF_OSR_DIV(mi2s, 0x48, 0x4c, 0x50); +CLK_AIF_OSR_DIV(codec_i2s_mic, 0x60, 0x64, 0x68); +CLK_AIF_OSR_DIV(spare_i2s_mic, 0x78, 0x7c, 0x80); +CLK_AIF_OSR_DIV(codec_i2s_spkr, 0x6c, 0x70, 0x74); +CLK_AIF_OSR_DIV(spare_i2s_spkr, 0x84, 0x88, 0x8c); + +/* + * PCM clock + * This table is evidently for using PLL4 as parent, if we start using + * LPA_PLL0 we need to provide a second table. + */ +static struct freq_tbl clk_tbl_pcm_pll4[] = { + { 512000, P_PLL4_LPA_PLL0, 4, 1, 264 }, + { 768000, P_PLL4_LPA_PLL0, 4, 1, 176 }, + { 1024000, P_PLL4_LPA_PLL0, 4, 1, 132 }, + { 1536000, P_PLL4_LPA_PLL0, 4, 1, 88 }, + { 2048000, P_PLL4_LPA_PLL0, 4, 1, 66 }, + { 3072000, P_PLL4_LPA_PLL0, 4, 1, 44 }, + { 4096000, P_PLL4_LPA_PLL0, 4, 1, 33 }, + { 6144000, P_PLL4_LPA_PLL0, 4, 1, 22 }, + { 8192000, P_PLL4_LPA_PLL0, 2, 1, 33 }, + { 12288000, P_PLL4_LPA_PLL0, 4, 1, 11 }, + { 24580000, P_PLL4_LPA_PLL0, 2, 1, 11 }, + { 27000000, P_PXO, 1, 0, 0 }, + { }, +}; + +static struct clk_rcg pcm_src = { + .ns_reg = 0x54, + .md_reg = 0x58, + .mn = { + .mnctr_en_bit = 8, + .mnctr_reset_bit = 7, + .mnctr_mode_shift = 5, + .n_val_shift = 16, + .m_val_shift = 16, + .width = 16, + }, + .p = { + .pre_div_shift = 3, + .pre_div_width = 2, + }, + .s = { + .src_sel_shift = 0, + .parent_map = lcc_parent_map, + }, + .freq_tbl = clk_tbl_pcm_pll4, + .clkr = { + .enable_reg = 0x54, + .enable_mask = BIT(9), + .hw.init = &(struct clk_init_data){ + .name = "pcm_src", + .parent_names = lcc_parent_tbl, + .num_parents = 4, + .ops = &clk_rcg_ops, + .flags = CLK_SET_RATE_GATE, + }, + }, +}; + +static struct clk_branch pcm_clk_out = { + .halt_reg = 0x5c, + .halt_bit = 0, + .halt_check = BRANCH_HALT_ENABLE, + .clkr = { + .enable_reg = 0x54, + .enable_mask = BIT(11), + .hw.init = &(struct clk_init_data){ + .name = "pcm_clk_out", + .parent_names = (const char *[]){ "pcm_src" }, + .num_parents = 1, + .ops = &clk_branch_ops, + .flags = CLK_SET_RATE_PARENT, + }, + }, +}; + +static struct clk_regmap_mux pcm_clk = { + .reg = 0x54, + .shift = 10, + .width = 1, + .clkr = { + .hw.init = &(struct clk_init_data){ + .name = "pcm_clk", + .parent_names = (const char *[]){ + "pcm_clk_out", + "pcm_codec_clk", + }, + .num_parents = 2, + .ops = &clk_regmap_mux_closest_ops, + .flags = CLK_SET_RATE_PARENT, + }, + }, +}; + +static struct clk_regmap *lcc_msm8660_clks[] = { + [LPA_PLL0] = &lpa_pll0.clkr, + [MI2S_OSR_SRC] = &mi2s_osr_src.clkr, + [MI2S_OSR_CLK] = &mi2s_osr_clk.clkr, + [MI2S_DIV_CLK] = &mi2s_div_clk.clkr, + [MI2S_BIT_DIV_CLK] = &mi2s_bit_div_clk.clkr, + [MI2S_BIT_CLK] = &mi2s_bit_clk.clkr, + [CODEC_I2S_MIC_OSR_SRC] = &codec_i2s_mic_osr_src.clkr, + [CODEC_I2S_MIC_OSR_CLK] = &codec_i2s_mic_osr_clk.clkr, + [CODEC_I2S_MIC_DIV_CLK] = &codec_i2s_mic_div_clk.clkr, + [CODEC_I2S_MIC_BIT_DIV_CLK] = &codec_i2s_mic_bit_div_clk.clkr, + [CODEC_I2S_MIC_BIT_CLK] = &codec_i2s_mic_bit_clk.clkr, + [SPARE_I2S_MIC_OSR_SRC] = &spare_i2s_mic_osr_src.clkr, + [SPARE_I2S_MIC_OSR_CLK] = &spare_i2s_mic_osr_clk.clkr, + [SPARE_I2S_MIC_DIV_CLK] = &spare_i2s_mic_div_clk.clkr, + [SPARE_I2S_MIC_BIT_DIV_CLK] = &spare_i2s_mic_bit_div_clk.clkr, + [SPARE_I2S_MIC_BIT_CLK] = &spare_i2s_mic_bit_clk.clkr, + [CODEC_I2S_SPKR_OSR_SRC] = &codec_i2s_spkr_osr_src.clkr, + [CODEC_I2S_SPKR_OSR_CLK] = &codec_i2s_spkr_osr_clk.clkr, + [CODEC_I2S_SPKR_DIV_CLK] = &codec_i2s_spkr_div_clk.clkr, + [CODEC_I2S_SPKR_BIT_DIV_CLK] = &codec_i2s_spkr_bit_div_clk.clkr, + [CODEC_I2S_SPKR_BIT_CLK] = &codec_i2s_spkr_bit_clk.clkr, + [SPARE_I2S_SPKR_OSR_SRC] = &spare_i2s_spkr_osr_src.clkr, + [SPARE_I2S_SPKR_OSR_CLK] = &spare_i2s_spkr_osr_clk.clkr, + [SPARE_I2S_SPKR_DIV_CLK] = &spare_i2s_spkr_div_clk.clkr, + [SPARE_I2S_SPKR_BIT_DIV_CLK] = &spare_i2s_spkr_bit_div_clk.clkr, + [SPARE_I2S_SPKR_BIT_CLK] = &spare_i2s_spkr_bit_clk.clkr, + [PCM_SRC] = &pcm_src.clkr, + [PCM_CLK_OUT] = &pcm_clk_out.clkr, + [PCM_CLK] = &pcm_clk.clkr, +}; + +static const struct regmap_config lcc_msm8660_regmap_config = { + .reg_bits = 32, + .reg_stride = 4, + .val_bits = 32, + .max_register = 0xfc, + .fast_io = true, +}; + +static const struct qcom_cc_desc lcc_msm8660_desc = { + .config = &lcc_msm8660_regmap_config, + .clks = lcc_msm8660_clks, + .num_clks = ARRAY_SIZE(lcc_msm8660_clks), +}; + +static const struct of_device_id lcc_msm8660_match_table[] = { + { .compatible = "qcom,lcc-msm8660" }, + { } +}; +MODULE_DEVICE_TABLE(of, lcc_msm8660_match_table); + +static int lcc_msm8660_probe(struct platform_device *pdev) +{ + u32 val; + struct regmap *regmap; + + regmap = qcom_cc_map(pdev, &lcc_msm8660_desc); + if (IS_ERR(regmap)) + return PTR_ERR(regmap); + + /* Configure the rate of LPA_PLL0 if the bootloader hasn't already */ + regmap_read(regmap, 0x0, &val); + if (!val) { + dev_info(&pdev->dev, "configuring LPA_PLL0\n"); + clk_pll_configure_sr(&lpa_pll0, regmap, &lpa_pll0_config, true); + } else { + dev_info(&pdev->dev, + "LPA_PLL0 already configured\n"); + } + + /* + * Enable LPA_PLL0 source on the LPASS Primary PLL Mux. Incidentally + * this is set to 0x00000001 at boot. + * 0x01 = LPA_PLL0 + */ + regmap_write(regmap, 0xc4, 0x1); + + return qcom_cc_really_probe(pdev, &lcc_msm8660_desc, regmap); +} + +static struct platform_driver lcc_msm8660_driver = { + .probe = lcc_msm8660_probe, + .driver = { + .name = "lcc-msm8660", + .of_match_table = lcc_msm8660_match_table, + }, +}; +module_platform_driver(lcc_msm8660_driver); + +MODULE_DESCRIPTION("QCOM LCC MSM8660 Driver"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:lcc-msm8660");
This adds support for the MSM8660 Low-power audio subsystem (LPASS) clock controller (LCC). This is nice when you want to have audio from the system. We currently only support using the PLL4 (which is an RPM clock) as the parent, however the LPASS has its own PLL named LPA_PLL0 that we can experiment with enabling later on, so for this reason the code contains a few hints on how to enable the LPA_PLL0. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v1->v2: - No changes. --- drivers/clk/qcom/Kconfig | 9 + drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/lcc-msm8660.c | 418 +++++++++++++++++++++++++++++++++++++++++ 3 files changed, 428 insertions(+) create mode 100644 drivers/clk/qcom/lcc-msm8660.c -- 2.9.3 -- To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html