new file mode 100644
@@ -0,0 +1,92 @@
+Cortina Systems Gemini Ethernet Controller
+==========================================
+
+This ethernet controller is found in the Gemini SoC family:
+StorLink SL3512 and SL3516, also known as Cortina Systems
+CS3512 and CS3516.
+
+Required properties:
+- compatible: must be "cortina,gemini-ethernet"
+- reg: must contain the global registers and the V-bit and A-bit
+ memory areas, in total three register sets.
+- syscon: a phandle to the system controller
+- #address-cells: must be specified, must be <1>
+- #size-cells: must be specified, must be <1>
+- ranges: should be state like this giving a 1:1 address translation
+ for the subnodes
+
+The subnodes represents the two ethernet ports in this device.
+They are not independent of each other since they share resources
+in the parent node, and are thus children.
+
+Required subnodes:
+- port0: contains the resources for ethernet port 0
+- port1: contains the resources for ethernet port 1
+
+Required subnode properties:
+- compatible: must be "cortina,gemini-ethernet-port"
+- reg: must contain two register areas: the DMA/TOE memory and
+ the GMAC memory area of the port
+- interrupts: should contain the interrupt line of the port.
+ this is nominally a level interrupt active high.
+- resets: this must provide an SoC-integrated reset line for
+ the port.
+- clocks: this should contain a handle to the PCLK clock for
+ clocking the silicon in this port
+- clock-names: must be "PCLK"
+
+Optional subnode properties:
+- phy-mode: see ethernet.txt
+- phy-handle: see ethernet.txt
+
+Example:
+
+mdio-bus {
+ (...)
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+ phy1: ethernet-phy@3 {
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+};
+
+
+ethernet@60000000 {
+ compatible = "cortina,gemini-ethernet";
+ reg = <0x60000000 0x4000>, /* Global registers, queue */
+ <0x60004000 0x2000>, /* V-bit */
+ <0x60006000 0x2000>; /* A-bit */
+ syscon = <&syscon>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ gmac0: ethernet-port@0 {
+ compatible = "cortina,gemini-ethernet-port";
+ reg = <0x60008000 0x2000>, /* Port 0 DMA/TOE */
+ <0x6000a000 0x2000>; /* Port 0 GMAC */
+ interrupt-parent = <&intcon>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_GMAC0>;
+ clocks = <&syscon GEMINI_CLK_GATE_GMAC0>;
+ clock-names = "PCLK";
+ phy-mode = "rgmii";
+ phy-handle = <&phy0>;
+ };
+
+ gmac1: ethernet-port@1 {
+ compatible = "cortina,gemini-ethernet-port";
+ reg = <0x6000c000 0x2000>, /* Port 1 DMA/TOE */
+ <0x6000e000 0x2000>; /* Port 1 GMAC */
+ interrupt-parent = <&intcon>;
+ interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+ resets = <&syscon GEMINI_RESET_GMAC1>;
+ clocks = <&syscon GEMINI_CLK_GATE_GMAC1>;
+ clock-names = "PCLK";
+ phy-mode = "rgmii";
+ phy-handle = <&phy1>;
+ };
+};
This adds the device tree bindings for the Gemini ethernet controller. It is pretty straight-forward, using standard bindings and modelling the two child ports as child devices under the parent ethernet controller device. Cc: devicetree@vger.kernel.org Cc: Tobias Waldvogel <tobias.waldvogel@gmail.com> Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v7->v8: - Use ethernet-port@0 and ethernet-port@1 with unit names and following OF graph requirements. --- .../bindings/net/cortina,gemini-ethernet.txt | 92 ++++++++++++++++++++++ 1 file changed, 92 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/cortina,gemini-ethernet.txt -- 2.14.3 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html