[v2,2/2] power: supply: Add Spreadtrum SC2731 charger support

diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index ff6dab0..f27cf07 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -645,4 +645,11 @@  config CHARGER_CROS_USBPD
 	  what is connected to USB PD ports from the EC and converts
 	  that into power_supply properties.
 
+config CHARGER_SC2731
+	tristate "Spreadtrum SC2731 charger driver"
+	depends on MFD_SC27XX_PMIC || COMPILE_TEST
+	help
+	 Say Y here to enable support for battery charging with SC2731
+	 PMIC chips.
+
 endif # POWER_SUPPLY
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index a26b402..767105b 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -85,3 +85,4 @@  obj-$(CONFIG_CHARGER_TPS65217)	+= tps65217_charger.o
 obj-$(CONFIG_AXP288_FUEL_GAUGE) += axp288_fuel_gauge.o
 obj-$(CONFIG_AXP288_CHARGER)	+= axp288_charger.o
 obj-$(CONFIG_CHARGER_CROS_USBPD)	+= cros_usbpd-charger.o
+obj-$(CONFIG_CHARGER_SC2731)	+= sc2731_charger.o
diff --git a/drivers/power/supply/sc2731_charger.c b/drivers/power/supply/sc2731_charger.c
new file mode 100644
index 0000000..c92e5fc
--- /dev/null
+++ b/drivers/power/supply/sc2731_charger.c
@@ -0,0 +1,503 @@ 
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (C) 2018 Spreadtrum Communications Inc.
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+#include <linux/usb/phy.h>
+#include <linux/regmap.h>
+#include <linux/notifier.h>
+#include <linux/of.h>
+
+/* PMIC global registers definition */
+#define SC2731_CHARGE_STATUS		0xedc
+#define SC2731_CHARGE_FULL		BIT(4)
+#define SC2731_MODULE_EN1		0xc0c
+#define SC2731_CHARGE_EN		BIT(5)
+
+/* SC2731 switch charger registers definition */
+#define SC2731_CHG_CFG0			0x0
+#define SC2731_CHG_CFG1			0x4
+#define SC2731_CHG_CFG2			0x8
+#define SC2731_CHG_CFG3			0xc
+#define SC2731_CHG_CFG4			0x10
+#define SC2731_CHG_CFG5			0x28
+
+/* SC2731_CHG_CFG0 register definition */
+#define SC2731_PRECHG_RNG_SHIFT		11
+#define SC2731_PRECHG_RNG_MASK		GENMASK(12, 11)
+
+#define SC2731_TERMINATION_VOL_MASK	GENMASK(2, 1)
+#define SC2731_TERMINATION_VOL_SHIFT	1
+#define SC2731_TERMINATION_VOL_CAL_MASK	GENMASK(8, 3)
+#define SC2731_TERMINATION_VOL_CAL_SHIFT	3
+#define SC2731_TERMINATION_CUR_MASK	GENMASK(2, 0)
+
+#define SC2731_CC_EN			BIT(13)
+#define SC2731_CHARGER_PD		BIT(0)
+
+/* SC2731_CHG_CFG1 register definition */
+#define SC2731_CUR_MASK			GENMASK(5, 0)
+
+/* SC2731_CHG_CFG5 register definition */
+#define SC2731_CUR_LIMIT_SHIFT		8
+#define SC2731_CUR_LIMIT_MASK		GENMASK(9, 8)
+
+/* Default current definition (unit is mA) */
+#define SC2731_CURRENT_LIMIT_100	100
+#define SC2731_CURRENT_LIMIT_500	500
+#define SC2731_CURRENT_LIMIT_900	900
+#define SC2731_CURRENT_LIMIT_2000	2000
+#define SC2731_CURRENT_PRECHG		450
+#define SC2731_CURRENT_STEP		50
+
+struct sc2731_charger_info {
+	struct device *dev;
+	struct regmap *regmap;
+	struct usb_phy *usb_phy;
+	struct notifier_block usb_notify;
+	struct power_supply *psy_usb;
+	struct mutex lock;
+	bool charging;
+	u32 base;
+};
+
+static void sc2731_charger_stop_charge(struct sc2731_charger_info *info)
+{
+	regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG0,
+			   SC2731_CC_EN, 0);
+
+	regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG0,
+			   SC2731_CHARGER_PD, SC2731_CHARGER_PD);
+}
+
+static int sc2731_charger_start_charge(struct sc2731_charger_info *info)
+{
+	int ret;
+
+	/* Enable charger constant current mode */
+	ret = regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG0,
+				 SC2731_CC_EN, SC2731_CC_EN);
+	if (ret)
+		return ret;
+
+	/* Start charging */
+	return regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG0,
+				  SC2731_CHARGER_PD, 0);
+}
+
+static int sc2731_charger_set_current_limit(struct sc2731_charger_info *info,
+					    u32 limit)
+{
+	u32 val;
+
+	if (limit <= SC2731_CURRENT_LIMIT_100)
+		val = 0;
+	else if (limit <= SC2731_CURRENT_LIMIT_500)
+		val = 3;
+	else if (limit <= SC2731_CURRENT_LIMIT_900)
+		val = 2;
+	else
+		val = 1;
+
+	return regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG5,
+				  SC2731_CUR_LIMIT_MASK,
+				  val << SC2731_CUR_LIMIT_SHIFT);
+}
+
+static int sc2731_charger_set_current(struct sc2731_charger_info *info, u32 cur)
+{
+	u32 val;
+	int ret;
+
+	if (cur > SC2731_CURRENT_LIMIT_2000)
+		cur = SC2731_CURRENT_LIMIT_2000;
+	else if (cur < SC2731_CURRENT_PRECHG)
+		cur = SC2731_CURRENT_PRECHG;
+
+	/* Calculate the step value, each step is 50 mA */
+	val = (cur - SC2731_CURRENT_PRECHG) / SC2731_CURRENT_STEP;
+
+	/* Set pre-charge current as 450 mA */
+	ret = regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG0,
+				 SC2731_PRECHG_RNG_MASK,
+				 0x3 << SC2731_PRECHG_RNG_SHIFT);
+	if (ret)
+		return ret;
+
+	return regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG1,
+				  SC2731_CUR_MASK, val);
+}
+
+static int sc2731_charger_get_status(struct sc2731_charger_info *info)
+{
+	u32 val;
+	int ret;
+
+	ret = regmap_read(info->regmap, SC2731_CHARGE_STATUS, &val);
+	if (ret)
+		return ret;
+
+	if (val & SC2731_CHARGE_FULL)
+		return POWER_SUPPLY_STATUS_FULL;
+
+	return POWER_SUPPLY_STATUS_CHARGING;
+}
+
+static int sc2731_charger_get_current(struct sc2731_charger_info *info,
+				      u32 *cur)
+{
+	int ret;
+	u32 val;
+
+	ret = regmap_read(info->regmap, info->base + SC2731_CHG_CFG1, &val);
+	if (ret)
+		return ret;
+
+	val &= SC2731_CUR_MASK;
+	*cur = val * SC2731_CURRENT_STEP + SC2731_CURRENT_PRECHG;
+
+	return 0;
+}
+
+static int sc2731_charger_get_current_limit(struct sc2731_charger_info *info,
+					    u32 *cur)
+{
+	int ret;
+	u32 val;
+
+	ret = regmap_read(info->regmap, info->base + SC2731_CHG_CFG5, &val);
+	if (ret)
+		return ret;
+
+	val = (val & SC2731_CUR_LIMIT_MASK) >> SC2731_CUR_LIMIT_SHIFT;
+
+	switch (val) {
+	case 0:
+		*cur = SC2731_CURRENT_LIMIT_100;
+		break;
+
+	case 1:
+		*cur = SC2731_CURRENT_LIMIT_2000;
+		break;
+
+	case 2:
+		*cur = SC2731_CURRENT_LIMIT_900;
+		break;
+
+	case 3:
+		*cur = SC2731_CURRENT_LIMIT_500;
+		break;
+
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int
+sc2731_charger_usb_set_property(struct power_supply *psy,
+				enum power_supply_property psp,
+				const union power_supply_propval *val)
+{
+	struct sc2731_charger_info *info = power_supply_get_drvdata(psy);
+	int ret;
+
+	mutex_lock(&info->lock);
+
+	if (!info->charging) {
+		mutex_unlock(&info->lock);
+		return -ENODEV;
+	}
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
+		ret = sc2731_charger_set_current(info, val->intval);
+		if (ret < 0)
+			dev_err(info->dev, "set charge current failed\n");
+		break;
+
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		ret = sc2731_charger_set_current_limit(info, val->intval);
+		if (ret < 0)
+			dev_err(info->dev, "set input current limit failed\n");
+		break;
+
+	default:
+		ret = -EINVAL;
+	}
+
+	mutex_unlock(&info->lock);
+	return ret;
+}
+
+static int sc2731_charger_usb_get_property(struct power_supply *psy,
+					   enum power_supply_property psp,
+					   union power_supply_propval *val)
+{
+	struct sc2731_charger_info *info = power_supply_get_drvdata(psy);
+	int ret = 0;
+	u32 cur;
+
+	mutex_lock(&info->lock);
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_STATUS:
+		if (info->charging)
+			val->intval = sc2731_charger_get_status(info);
+		else
+			val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
+		break;
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
+		if (!info->charging) {
+			val->intval = 0;
+		} else {
+			ret = sc2731_charger_get_current(info, &cur);
+			if (ret)
+				goto out;
+
+			val->intval = cur;
+		}
+		break;
+
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		if (!info->charging) {
+			val->intval = 0;
+		} else {
+			ret = sc2731_charger_get_current_limit(info, &cur);
+			if (ret)
+				goto out;
+
+			val->intval = cur;
+		}
+		break;
+
+	default:
+		ret = -EINVAL;
+	}
+
+out:
+	mutex_unlock(&info->lock);
+	return ret;
+}
+
+static int sc2731_charger_property_is_writeable(struct power_supply *psy,
+						enum power_supply_property psp)
+{
+	int ret;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
+	case POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT:
+		ret = 1;
+		break;
+
+	default:
+		ret = 0;
+	}
+
+	return ret;
+}
+
+static enum power_supply_property sc2731_usb_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
+	POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT,
+};
+
+static const struct power_supply_desc sc2731_charger_desc = {
+	.name			= "sc2731_charger",
+	.type			= POWER_SUPPLY_TYPE_USB,
+	.properties		= sc2731_usb_props,
+	.num_properties		= ARRAY_SIZE(sc2731_usb_props),
+	.get_property		= sc2731_charger_usb_get_property,
+	.set_property		= sc2731_charger_usb_set_property,
+	.property_is_writeable	= sc2731_charger_property_is_writeable,
+};
+
+static int sc2731_charger_usb_change(struct notifier_block *nb,
+				     unsigned long limit, void *data)
+{
+	struct sc2731_charger_info *info =
+		container_of(nb, struct sc2731_charger_info, usb_notify);
+	int ret = 0;
+
+	mutex_lock(&info->lock);
+
+	if (limit > 0) {
+		/* set current limitation and start to charge */
+		ret = sc2731_charger_set_current_limit(info, limit);
+		if (ret)
+			goto out;
+
+		ret = sc2731_charger_set_current(info, limit);
+		if (ret)
+			goto out;
+
+		ret = sc2731_charger_start_charge(info);
+		if (ret)
+			goto out;
+
+		info->charging = true;
+	} else {
+		/* Stop charging */
+		info->charging = false;
+		sc2731_charger_stop_charge(info);
+	}
+
+out:
+	mutex_unlock(&info->lock);
+	return ret;
+}
+
+static int sc2731_charger_hw_init(struct sc2731_charger_info *info)
+{
+	struct power_supply_battery_info bat_info = { };
+	u32 term_currrent, term_voltage, cur_val, vol_val;
+	int ret;
+
+	/* Enable charger module */
+	ret = regmap_update_bits(info->regmap, SC2731_MODULE_EN1,
+				 SC2731_CHARGE_EN, SC2731_CHARGE_EN);
+	if (ret)
+		return ret;
+
+	ret = power_supply_get_battery_info(info->psy_usb, &bat_info);
+	if (ret) {
+		dev_warn(info->dev, "no battery information is supplied\n");
+
+		/*
+		 * If no battery information is supplied, we should set
+		 * default charge termination current to 120 mA, and default
+		 * charge termination voltage to 4.35V.
+		 */
+		cur_val = 0x2;
+		vol_val = 0x1;
+	} else {
+		term_currrent = bat_info.charge_term_current_ua / 1000;
+
+		if (term_currrent <= 90)
+			cur_val = 0;
+		else if (term_currrent >= 265)
+			cur_val = 0x7;
+		else
+			cur_val = ((term_currrent - 90) / 25) + 1;
+
+		term_voltage = bat_info.constant_charge_voltage_max_uv / 1000;
+
+		if (term_voltage > 4500)
+			term_voltage = 4500;
+
+		if (term_voltage > 4200)
+			vol_val = (term_voltage - 4200) / 100;
+		else
+			vol_val = 0;
+	}
+
+	/* Set charge termination current */
+	ret = regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG2,
+				 SC2731_TERMINATION_CUR_MASK, cur_val);
+	if (ret)
+		goto error;
+
+	/* Set charge termination voltage */
+	ret = regmap_update_bits(info->regmap, info->base + SC2731_CHG_CFG0,
+				 SC2731_TERMINATION_VOL_MASK |
+				 SC2731_TERMINATION_VOL_CAL_MASK,
+				 (vol_val << SC2731_TERMINATION_VOL_SHIFT) |
+				 (0x6 << SC2731_TERMINATION_VOL_CAL_SHIFT));
+	if (ret)
+		goto error;
+
+	return 0;
+
+error:
+	regmap_update_bits(info->regmap, SC2731_MODULE_EN1, SC2731_CHARGE_EN, 0);
+	return ret;
+}
+
+static int sc2731_charger_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct sc2731_charger_info *info;
+	struct power_supply_config charger_cfg = { };
+	int ret;
+
+	info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
+	if (!info)
+		return -ENOMEM;
+
+	mutex_init(&info->lock);
+	info->dev = &pdev->dev;
+
+	info->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!info->regmap) {
+		dev_err(&pdev->dev, "failed to get charger regmap\n");
+		return -ENODEV;
+	}
+
+	ret = of_property_read_u32(np, "reg", &info->base);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to get register address\n");
+		return -ENODEV;
+	}
+
+	charger_cfg.drv_data = info;
+	charger_cfg.of_node = np;
+	info->psy_usb = devm_power_supply_register(&pdev->dev,
+						   &sc2731_charger_desc,
+						   &charger_cfg);
+	if (IS_ERR(info->psy_usb)) {
+		dev_err(&pdev->dev, "failed to register power supply\n");
+		return PTR_ERR(info->psy_usb);
+	}
+
+	ret = sc2731_charger_hw_init(info);
+	if (ret)
+		return ret;
+
+	info->usb_phy = devm_usb_get_phy_by_phandle(&pdev->dev, "phys", 0);
+	if (IS_ERR(info->usb_phy)) {
+		dev_err(&pdev->dev, "failed to find USB phy\n");
+		return PTR_ERR(info->usb_phy);
+	}
+
+	info->usb_notify.notifier_call = sc2731_charger_usb_change;
+	ret = usb_register_notifier(info->usb_phy, &info->usb_notify);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to register notifier: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int sc2731_charger_remove(struct platform_device *pdev)
+{
+	struct sc2731_charger_info *info = platform_get_drvdata(pdev);
+
+	usb_unregister_notifier(info->usb_phy, &info->usb_notify);
+
+	return 0;
+}
+
+static const struct of_device_id sc2731_charger_of_match[] = {
+	{ .compatible = "sprd,sc2731-charger", },
+	{ }
+};
+
+static struct platform_driver sc2731_charger_driver = {
+	.driver = {
+		.name = "sc2731-charger",
+		.of_match_table = sc2731_charger_of_match,
+	},
+	.probe = sc2731_charger_probe,
+	.remove = sc2731_charger_remove,
+};
+
+module_platform_driver(sc2731_charger_driver);
+
+MODULE_DESCRIPTION("Spreadtrum SC2731 Charger Driver");
+MODULE_LICENSE("GPL v2");