new file mode 100644
@@ -0,0 +1,104 @@
+ST-Ericsson Multi Channel Display Engine MCDE
+
+The ST-Ericsson MCDE is a display controller with support for compositing
+and displaying several channels memory resident graphics data on DSI or
+LCD displays or bridges. It is used in the ST-Ericsson U8500 platform.
+
+Required properties:
+
+- compatible: must be:
+ "ste,mcde"
+- reg: register base for the main MCDE control registers, should be
+ 0x1000 in size
+- interrupts: the interrupt line for the MCDE
+- epod-supply: a phandle to the EPOD regulator
+- vana-supply: a phandle to the analog voltage regulator
+- clocks: an array of the MCDE clocks in this strict order:
+ MCDECLK (main MCDE clock), LCDCLK (LCD clock), PLLDSI
+ (HDMI clock), DSI0ESCLK (DSI0 energy save clock),
+ DSI1ESCLK (DSI1 energy save clock), DSI2ESCLK (DSI2 energy
+ save clock)
+- clock-names: must be the following array:
+ "mcde", "lcd", "hdmi"
+ to match the required clock inputs above.
+- #address-cells: should be <1> (for the DSI hosts that will be children)
+- #size-cells: should be <1> (for the DSI hosts that will be children)
+- ranges: this should always be stated
+
+Required subnodes:
+
+The devicetree must specify subnodes for the DSI host adapters.
+These must have the following characteristics:
+
+- compatible: must be:
+ "ste,mcde-dsi"
+- reg: must specify the register range for the DSI host
+- vana-supply: phandle to the VANA voltage regulator
+- clocks: phandles to the high speed and low power (energy save) clocks
+ the high speed clock is not present on the third (dsi2) block, so it
+ should only have the "lp" clock
+- clock-names: "hs" for the high speed clock and "lp" for the low power
+ (energy save) clock
+- #address-cells: should be <1>
+- #size-cells: should be <0>
+
+Display panels and bridges will appear as children on the DSI hosts, and
+the displays are connected to the DSI hosts using the common binding
+for video transmitter interfaces; see
+Documentation/devicetree/bindings/media/video-interfaces.txt
+
+If a DSI host is unused (not connected) it will have no children defined.
+
+Example:
+
+mcde@a0350000 {
+ compatible = "ste,mcde";
+ reg = <0xa0350000 0x1000>;
+ interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+ epod-supply = <&db8500_b2r2_mcde_reg>;
+ vana-supply = <&ab8500_ldo_ana_reg>;
+ clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */
+ <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */
+ <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */
+ clock-names = "mcde", "lcd", "hdmi";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dsi0: dsi@a0351000 {
+ compatible = "ste,mcde-dsi";
+ reg = <0xa0351000 0x1000>;
+ vana-supply = <&ab8500_ldo_ana_reg>;
+ clocks = <&prcmu_clk PRCMU_DSI0CLK>, <&prcmu_clk PRCMU_DSI0ESCCLK>;
+ clock-names = "hs", "lp";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel {
+ compatible = "samsung,s6d16d0";
+ reg = <0>;
+ vdd1-supply = <&ab8500_ldo_aux1_reg>;
+ reset-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+ };
+
+ };
+ dsi1: dsi@a0352000 {
+ compatible = "ste,mcde-dsi";
+ reg = <0xa0352000 0x1000>;
+ vana-supply = <&ab8500_ldo_ana_reg>;
+ clocks = <&prcmu_clk PRCMU_DSI1CLK>, <&prcmu_clk PRCMU_DSI1ESCCLK>;
+ clock-names = "hs", "lp";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ dsi2: dsi@a0353000 {
+ compatible = "ste,mcde-dsi";
+ reg = <0xa0353000 0x1000>;
+ vana-supply = <&ab8500_ldo_ana_reg>;
+ /* This DSI port only has the Low Power / Energy Save clock */
+ clocks = <&prcmu_clk PRCMU_DSI2ESCCLK>;
+ clock-names = "lp";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
This adds the device tree bindings for the ST-Ericsson Multi Channel Display Engine MCDE as found in the U8500 SoCs. Cc: devicetree@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v1->v2: - Drop the graph representation of a port from DSI host to panel child. Just have panels or bridges be children of the DSI host. - Just name the panel node "panel". - Move the HS and LP/ES clocks to be properties on their respective DSI host device nodes. - Clarify that the third DSI block (DSI2) does not have any high speed clock. --- .../devicetree/bindings/display/ste,mcde.txt | 104 ++++++++++++++++++ 1 file changed, 104 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/ste,mcde.txt -- 2.20.1