diff mbox series

[v2] Input: tsc2007 - use GPIO descriptor

Message ID 20190823071021.5598-1-linus.walleij@linaro.org
State New
Headers show
Series [v2] Input: tsc2007 - use GPIO descriptor | expand

Commit Message

Linus Walleij Aug. 23, 2019, 7:10 a.m. UTC 
This switches the TSC2007 to use a GPIO descriptor to read
the pendown GPIO line.

As this will make the gpiolib start to respect polarity
inversion flags on the GPIO lines, drop the inversion when
reading the line with gpio_get_value(), fix two offenders
in the i.MX device trees, and also emphasize the importance
of marking the polarity right in the device tree bindings.

Cc: Denis Carikli <denis@eukrea.com>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

---
ChangeLog v1->v2:
- Drop inversion on the GPIO descriptor value, rely on the
  gpiolib to handle polarity inversion.
- Comb through device trees, identify two offenders, fix
  them as part of the patch for a clean cut.
- Also fix the device tree bindings.
---
 .../bindings/input/touchscreen/tsc2007.txt         |  5 +++--
 arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi       |  3 ++-
 arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi       |  3 ++-
 drivers/input/touchscreen/tsc2007.h                |  4 +++-
 drivers/input/touchscreen/tsc2007_core.c           | 14 +++++++-------
 5 files changed, 17 insertions(+), 12 deletions(-)

-- 
2.21.0

Comments

Dmitry Torokhov Sept. 2, 2019, 3:48 p.m. UTC | #1 
On Tue, Aug 27, 2019 at 09:42:46AM +0200, Linus Walleij wrote:
> On Tue, Aug 27, 2019 at 12:00 AM Dmitry Torokhov

> <dmitry.torokhov@gmail.com> wrote:

> 

> > >  Optional properties:

> > >  - gpios: the interrupt gpio the chip is connected to (trough the penirq pin).

> > > -  The penirq pin goes to low when the panel is touched.

> > > +  The penirq pin goes to low when the panel is touched, so make sure to tag

> > > +  the GPIO line with GPIO_ACTIVE_LOW.

> >

> > I think this is too strong. I am sure that one can come up with a way to

> > connect the attention signal though polarity inverter and then one would

> > have to specify GPIO_ACTIVE_HIGH in the DT.

> 

> Yeah this is something that has been discussed recently as

> Harish is suggesting to add an actual inverter to the device

> tree model. As the description of reality in the device tree is

> incomplete, these flags, which should nominally be consumer

> flags and indicate the behavior of the consumer, becomes

> a panacea for solving shortcomings in the device tree model.

> 

> I am in favor of introducing explicit inverters in device tree,

> as it makes the descriptions more consistent: e.g. regulators

> are consumer oriented, they even model rails to make things

> very clear on where a voltage applies, whereas GPIO polarity

> is defined as "trial-and-error until whatever makes the system

> run" more or less.

> 

> > Can we say:

> >

> > The penirq pin goes to low when the panel is touched, so GPIO line

> > should normally be tagged with GPIO_ACTIVE_LOW.

> 

> Sure, this is not the place for hashing out DT design issues,

> can you fix when applying or should I send a new version?


I can fix it up on my side, once I hear from DY folks that they are OK
with existing DTS changes.

Thanks.

-- 
Dmitry
Dmitry Torokhov Sept. 2, 2019, 3:51 p.m. UTC | #2 
On Fri, Aug 23, 2019 at 09:10:21AM +0200, Linus Walleij wrote:
> This switches the TSC2007 to use a GPIO descriptor to read

> the pendown GPIO line.

> 

> As this will make the gpiolib start to respect polarity

> inversion flags on the GPIO lines, drop the inversion when

> reading the line with gpio_get_value(), fix two offenders

> in the i.MX device trees, and also emphasize the importance

> of marking the polarity right in the device tree bindings.

> 

> Cc: Denis Carikli <denis@eukrea.com>

> Cc: Pengutronix Kernel Team <kernel@pengutronix.de>

> Cc: NXP Linux Team <linux-imx@nxp.com>

> Cc: H. Nikolaus Schaller <hns@goldelico.com>

> Cc: devicetree@vger.kernel.org

> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

> ---

> ChangeLog v1->v2:

> - Drop inversion on the GPIO descriptor value, rely on the

>   gpiolib to handle polarity inversion.

> - Comb through device trees, identify two offenders, fix

>   them as part of the patch for a clean cut.

> - Also fix the device tree bindings.

> ---

>  .../bindings/input/touchscreen/tsc2007.txt         |  5 +++--

>  arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi       |  3 ++-

>  arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi       |  3 ++-


Shawn, Sascha, any objections to these DTS changes?

>  drivers/input/touchscreen/tsc2007.h                |  4 +++-

>  drivers/input/touchscreen/tsc2007_core.c           | 14 +++++++-------

>  5 files changed, 17 insertions(+), 12 deletions(-)

> 

> diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt

> index ed00f61b8c08..b08b54d49699 100644

> --- a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt

> +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt

> @@ -7,7 +7,8 @@ Required properties:

>  

>  Optional properties:

>  - gpios: the interrupt gpio the chip is connected to (trough the penirq pin).

> -  The penirq pin goes to low when the panel is touched.

> +  The penirq pin goes to low when the panel is touched, so make sure to tag

> +  the GPIO line with GPIO_ACTIVE_LOW.

>    (see GPIO binding[1] for more details).

>  - interrupts: (gpio) interrupt to which the chip is connected

>    (see interrupt binding[0]).

> @@ -31,7 +32,7 @@ Example:

>  			reg = <0x49>;

>  			interrupt-parent = <&gpio4>;

>  			interrupts = <0x0 0x8>;

> -			gpios = <&gpio4 0 0>;

> +			gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;

>  			ti,x-plate-ohms = <180>;

>  		};

>  

> diff --git a/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi b/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi

> index 17bd2a97609a..b8ac60622936 100644

> --- a/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi

> +++ b/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi

> @@ -3,6 +3,7 @@

>   * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>

>   */

>  

> +#include <dt-bindings/gpio/gpio.h>

>  #include "imx35.dtsi"

>  

>  / {

> @@ -33,7 +34,7 @@

>  

>  	tsc2007: tsc2007@48 {

>  		compatible = "ti,tsc2007";

> -		gpios = <&gpio3 2 0>;

> +		gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;

>  		interrupt-parent = <&gpio3>;

>  		interrupts = <0x2 0x8>;

>  		pinctrl-names = "default";

> diff --git a/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi b/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi

> index c2a929ba8ceb..016d0bc64bdb 100644

> --- a/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi

> +++ b/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi

> @@ -3,6 +3,7 @@

>   * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>

>   */

>  

> +#include <dt-bindings/gpio/gpio.h>

>  #include "imx51.dtsi"

>  

>  / {

> @@ -33,7 +34,7 @@

>  

>  	tsc2007: tsc2007@49 {

>  		compatible = "ti,tsc2007";

> -		gpios = <&gpio4 0 1>;

> +		gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;

>  		interrupt-parent = <&gpio4>;

>  		interrupts = <0x0 0x8>;

>  		pinctrl-names = "default";

> diff --git a/drivers/input/touchscreen/tsc2007.h b/drivers/input/touchscreen/tsc2007.h

> index 91c60bf6dcaf..0306c38b56c7 100644

> --- a/drivers/input/touchscreen/tsc2007.h

> +++ b/drivers/input/touchscreen/tsc2007.h

> @@ -49,6 +49,8 @@

>  #define READ_X		(ADC_ON_12BIT | TSC2007_MEASURE_X)

>  #define PWRDOWN		(TSC2007_12BIT | TSC2007_POWER_OFF_IRQ_EN)

>  

> +struct gpio_desc;

> +

>  struct ts_event {

>  	u16	x;

>  	u16	y;

> @@ -69,7 +71,7 @@ struct tsc2007 {

>  	int			fuzzy;

>  	int			fuzzz;

>  

> -	unsigned int		gpio;

> +	struct gpio_desc	*gpiod;

>  	int			irq;

>  

>  	wait_queue_head_t	wait;

> diff --git a/drivers/input/touchscreen/tsc2007_core.c b/drivers/input/touchscreen/tsc2007_core.c

> index 3b80abfc1eca..0eadd6d86fa0 100644

> --- a/drivers/input/touchscreen/tsc2007_core.c

> +++ b/drivers/input/touchscreen/tsc2007_core.c

> @@ -23,7 +23,7 @@

>  #include <linux/interrupt.h>

>  #include <linux/i2c.h>

>  #include <linux/of_device.h>

> -#include <linux/of_gpio.h>

> +#include <linux/gpio/consumer.h>

>  #include <linux/platform_data/tsc2007.h>

>  #include "tsc2007.h"

>  

> @@ -226,7 +226,7 @@ static int tsc2007_get_pendown_state_gpio(struct device *dev)

>  	struct i2c_client *client = to_i2c_client(dev);

>  	struct tsc2007 *ts = i2c_get_clientdata(client);

>  

> -	return !gpio_get_value(ts->gpio);

> +	return gpiod_get_value(ts->gpiod);

>  }

>  

>  static int tsc2007_probe_dt(struct i2c_client *client, struct tsc2007 *ts)

> @@ -266,13 +266,13 @@ static int tsc2007_probe_dt(struct i2c_client *client, struct tsc2007 *ts)

>  		return -EINVAL;

>  	}

>  

> -	ts->gpio = of_get_gpio(np, 0);

> -	if (gpio_is_valid(ts->gpio))

> +	ts->gpiod = devm_gpiod_get_optional(&client->dev, NULL, GPIOD_IN);

> +	if (IS_ERR(ts->gpiod))

> +		return PTR_ERR(ts->gpiod);

> +	if (ts->gpiod)

>  		ts->get_pendown_state = tsc2007_get_pendown_state_gpio;

>  	else

> -		dev_warn(&client->dev,

> -			 "GPIO not specified in DT (of_get_gpio returned %d)\n",

> -			 ts->gpio);

> +		dev_warn(&client->dev, "GPIO not specified in DT\n");

>  

>  	return 0;

>  }

> -- 

> 2.21.0

> 


-- 
Dmitry
Shawn Guo Oct. 6, 2019, 12:02 a.m. UTC | #3 
On Mon, Sep 02, 2019 at 08:51:44AM -0700, Dmitry Torokhov wrote:
> On Fri, Aug 23, 2019 at 09:10:21AM +0200, Linus Walleij wrote:

> > This switches the TSC2007 to use a GPIO descriptor to read

> > the pendown GPIO line.

> > 

> > As this will make the gpiolib start to respect polarity

> > inversion flags on the GPIO lines, drop the inversion when

> > reading the line with gpio_get_value(), fix two offenders

> > in the i.MX device trees, and also emphasize the importance

> > of marking the polarity right in the device tree bindings.

> > 

> > Cc: Denis Carikli <denis@eukrea.com>

> > Cc: Pengutronix Kernel Team <kernel@pengutronix.de>

> > Cc: NXP Linux Team <linux-imx@nxp.com>

> > Cc: H. Nikolaus Schaller <hns@goldelico.com>

> > Cc: devicetree@vger.kernel.org

> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

> > ---

> > ChangeLog v1->v2:

> > - Drop inversion on the GPIO descriptor value, rely on the

> >   gpiolib to handle polarity inversion.

> > - Comb through device trees, identify two offenders, fix

> >   them as part of the patch for a clean cut.

> > - Also fix the device tree bindings.

> > ---

> >  .../bindings/input/touchscreen/tsc2007.txt         |  5 +++--

> >  arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi       |  3 ++-

> >  arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi       |  3 ++-

> 

> Shawn, Sascha, any objections to these DTS changes?


No objections from me.  But in generally, we prefer to have DTS changes
in separate patch going through arm-soc tree.

Shawn

> 

> >  drivers/input/touchscreen/tsc2007.h                |  4 +++-

> >  drivers/input/touchscreen/tsc2007_core.c           | 14 +++++++-------

> >  5 files changed, 17 insertions(+), 12 deletions(-)

> > 

> > diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt

> > index ed00f61b8c08..b08b54d49699 100644

> > --- a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt

> > +++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt

> > @@ -7,7 +7,8 @@ Required properties:

> >  

> >  Optional properties:

> >  - gpios: the interrupt gpio the chip is connected to (trough the penirq pin).

> > -  The penirq pin goes to low when the panel is touched.

> > +  The penirq pin goes to low when the panel is touched, so make sure to tag

> > +  the GPIO line with GPIO_ACTIVE_LOW.

> >    (see GPIO binding[1] for more details).

> >  - interrupts: (gpio) interrupt to which the chip is connected

> >    (see interrupt binding[0]).

> > @@ -31,7 +32,7 @@ Example:

> >  			reg = <0x49>;

> >  			interrupt-parent = <&gpio4>;

> >  			interrupts = <0x0 0x8>;

> > -			gpios = <&gpio4 0 0>;

> > +			gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;

> >  			ti,x-plate-ohms = <180>;

> >  		};

> >  

> > diff --git a/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi b/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi

> > index 17bd2a97609a..b8ac60622936 100644

> > --- a/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi

> > +++ b/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi

> > @@ -3,6 +3,7 @@

> >   * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>

> >   */

> >  

> > +#include <dt-bindings/gpio/gpio.h>

> >  #include "imx35.dtsi"

> >  

> >  / {

> > @@ -33,7 +34,7 @@

> >  

> >  	tsc2007: tsc2007@48 {

> >  		compatible = "ti,tsc2007";

> > -		gpios = <&gpio3 2 0>;

> > +		gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;

> >  		interrupt-parent = <&gpio3>;

> >  		interrupts = <0x2 0x8>;

> >  		pinctrl-names = "default";

> > diff --git a/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi b/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi

> > index c2a929ba8ceb..016d0bc64bdb 100644

> > --- a/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi

> > +++ b/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi

> > @@ -3,6 +3,7 @@

> >   * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>

> >   */

> >  

> > +#include <dt-bindings/gpio/gpio.h>

> >  #include "imx51.dtsi"

> >  

> >  / {

> > @@ -33,7 +34,7 @@

> >  

> >  	tsc2007: tsc2007@49 {

> >  		compatible = "ti,tsc2007";

> > -		gpios = <&gpio4 0 1>;

> > +		gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;

> >  		interrupt-parent = <&gpio4>;

> >  		interrupts = <0x0 0x8>;

> >  		pinctrl-names = "default";

> > diff --git a/drivers/input/touchscreen/tsc2007.h b/drivers/input/touchscreen/tsc2007.h

> > index 91c60bf6dcaf..0306c38b56c7 100644

> > --- a/drivers/input/touchscreen/tsc2007.h

> > +++ b/drivers/input/touchscreen/tsc2007.h

> > @@ -49,6 +49,8 @@

> >  #define READ_X		(ADC_ON_12BIT | TSC2007_MEASURE_X)

> >  #define PWRDOWN		(TSC2007_12BIT | TSC2007_POWER_OFF_IRQ_EN)

> >  

> > +struct gpio_desc;

> > +

> >  struct ts_event {

> >  	u16	x;

> >  	u16	y;

> > @@ -69,7 +71,7 @@ struct tsc2007 {

> >  	int			fuzzy;

> >  	int			fuzzz;

> >  

> > -	unsigned int		gpio;

> > +	struct gpio_desc	*gpiod;

> >  	int			irq;

> >  

> >  	wait_queue_head_t	wait;

> > diff --git a/drivers/input/touchscreen/tsc2007_core.c b/drivers/input/touchscreen/tsc2007_core.c

> > index 3b80abfc1eca..0eadd6d86fa0 100644

> > --- a/drivers/input/touchscreen/tsc2007_core.c

> > +++ b/drivers/input/touchscreen/tsc2007_core.c

> > @@ -23,7 +23,7 @@

> >  #include <linux/interrupt.h>

> >  #include <linux/i2c.h>

> >  #include <linux/of_device.h>

> > -#include <linux/of_gpio.h>

> > +#include <linux/gpio/consumer.h>

> >  #include <linux/platform_data/tsc2007.h>

> >  #include "tsc2007.h"

> >  

> > @@ -226,7 +226,7 @@ static int tsc2007_get_pendown_state_gpio(struct device *dev)

> >  	struct i2c_client *client = to_i2c_client(dev);

> >  	struct tsc2007 *ts = i2c_get_clientdata(client);

> >  

> > -	return !gpio_get_value(ts->gpio);

> > +	return gpiod_get_value(ts->gpiod);

> >  }

> >  

> >  static int tsc2007_probe_dt(struct i2c_client *client, struct tsc2007 *ts)

> > @@ -266,13 +266,13 @@ static int tsc2007_probe_dt(struct i2c_client *client, struct tsc2007 *ts)

> >  		return -EINVAL;

> >  	}

> >  

> > -	ts->gpio = of_get_gpio(np, 0);

> > -	if (gpio_is_valid(ts->gpio))

> > +	ts->gpiod = devm_gpiod_get_optional(&client->dev, NULL, GPIOD_IN);

> > +	if (IS_ERR(ts->gpiod))

> > +		return PTR_ERR(ts->gpiod);

> > +	if (ts->gpiod)

> >  		ts->get_pendown_state = tsc2007_get_pendown_state_gpio;

> >  	else

> > -		dev_warn(&client->dev,

> > -			 "GPIO not specified in DT (of_get_gpio returned %d)\n",

> > -			 ts->gpio);

> > +		dev_warn(&client->dev, "GPIO not specified in DT\n");

> >  

> >  	return 0;

> >  }

> > -- 

> > 2.21.0

> > 

> 

> -- 

> Dmitry
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
index ed00f61b8c08..b08b54d49699 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/tsc2007.txt
@@ -7,7 +7,8 @@  Required properties:
 
 Optional properties:
 - gpios: the interrupt gpio the chip is connected to (trough the penirq pin).
-  The penirq pin goes to low when the panel is touched.
+  The penirq pin goes to low when the panel is touched, so make sure to tag
+  the GPIO line with GPIO_ACTIVE_LOW.
   (see GPIO binding[1] for more details).
 - interrupts: (gpio) interrupt to which the chip is connected
   (see interrupt binding[0]).
@@ -31,7 +32,7 @@  Example:
 			reg = <0x49>;
 			interrupt-parent = <&gpio4>;
 			interrupts = <0x0 0x8>;
-			gpios = <&gpio4 0 0>;
+			gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
 			ti,x-plate-ohms = <180>;
 		};
 
diff --git a/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi b/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi
index 17bd2a97609a..b8ac60622936 100644
--- a/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi
+++ b/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi
@@ -3,6 +3,7 @@ 
  * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include "imx35.dtsi"
 
 / {
@@ -33,7 +34,7 @@ 
 
 	tsc2007: tsc2007@48 {
 		compatible = "ti,tsc2007";
-		gpios = <&gpio3 2 0>;
+		gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
 		interrupt-parent = <&gpio3>;
 		interrupts = <0x2 0x8>;
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi b/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi
index c2a929ba8ceb..016d0bc64bdb 100644
--- a/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi
+++ b/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi
@@ -3,6 +3,7 @@ 
  * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include "imx51.dtsi"
 
 / {
@@ -33,7 +34,7 @@ 
 
 	tsc2007: tsc2007@49 {
 		compatible = "ti,tsc2007";
-		gpios = <&gpio4 0 1>;
+		gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <0x0 0x8>;
 		pinctrl-names = "default";
diff --git a/drivers/input/touchscreen/tsc2007.h b/drivers/input/touchscreen/tsc2007.h
index 91c60bf6dcaf..0306c38b56c7 100644
--- a/drivers/input/touchscreen/tsc2007.h
+++ b/drivers/input/touchscreen/tsc2007.h
@@ -49,6 +49,8 @@ 
 #define READ_X		(ADC_ON_12BIT | TSC2007_MEASURE_X)
 #define PWRDOWN		(TSC2007_12BIT | TSC2007_POWER_OFF_IRQ_EN)
 
+struct gpio_desc;
+
 struct ts_event {
 	u16	x;
 	u16	y;
@@ -69,7 +71,7 @@  struct tsc2007 {
 	int			fuzzy;
 	int			fuzzz;
 
-	unsigned int		gpio;
+	struct gpio_desc	*gpiod;
 	int			irq;
 
 	wait_queue_head_t	wait;
diff --git a/drivers/input/touchscreen/tsc2007_core.c b/drivers/input/touchscreen/tsc2007_core.c
index 3b80abfc1eca..0eadd6d86fa0 100644
--- a/drivers/input/touchscreen/tsc2007_core.c
+++ b/drivers/input/touchscreen/tsc2007_core.c
@@ -23,7 +23,7 @@ 
 #include <linux/interrupt.h>
 #include <linux/i2c.h>
 #include <linux/of_device.h>
-#include <linux/of_gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/platform_data/tsc2007.h>
 #include "tsc2007.h"
 
@@ -226,7 +226,7 @@  static int tsc2007_get_pendown_state_gpio(struct device *dev)
 	struct i2c_client *client = to_i2c_client(dev);
 	struct tsc2007 *ts = i2c_get_clientdata(client);
 
-	return !gpio_get_value(ts->gpio);
+	return gpiod_get_value(ts->gpiod);
 }
 
 static int tsc2007_probe_dt(struct i2c_client *client, struct tsc2007 *ts)
@@ -266,13 +266,13 @@  static int tsc2007_probe_dt(struct i2c_client *client, struct tsc2007 *ts)
 		return -EINVAL;
 	}
 
-	ts->gpio = of_get_gpio(np, 0);
-	if (gpio_is_valid(ts->gpio))
+	ts->gpiod = devm_gpiod_get_optional(&client->dev, NULL, GPIOD_IN);
+	if (IS_ERR(ts->gpiod))
+		return PTR_ERR(ts->gpiod);
+	if (ts->gpiod)
 		ts->get_pendown_state = tsc2007_get_pendown_state_gpio;
 	else
-		dev_warn(&client->dev,
-			 "GPIO not specified in DT (of_get_gpio returned %d)\n",
-			 ts->gpio);
+		dev_warn(&client->dev, "GPIO not specified in DT\n");
 
 	return 0;
 }