[RFC,v4,4/4] scsi: ufs-qcom: add Inline Crypto Engine support

Message ID	20200501045111.665881-5-ebiggers@kernel.org
State	Superseded
Headers	show Return-Path: <SRS0=dvW1=6P=vger.kernel.org=linux-arm-msm-owner@kernel.org> From: Eric Biggers <ebiggers@kernel.org> To: linux-scsi@vger.kernel.org, linux-arm-msm@vger.kernel.org Cc: linux-block@vger.kernel.org, linux-fscrypt@vger.kernel.org, Alim Akhtar <alim.akhtar@samsung.com>, Andy Gross <agross@kernel.org>, Avri Altman <avri.altman@wdc.com>, Barani Muthukumaran <bmuthuku@qti.qualcomm.com>, Bjorn Andersson <bjorn.andersson@linaro.org>, Can Guo <cang@codeaurora.org>, Elliot Berman <eberman@codeaurora.org>, John Stultz <john.stultz@linaro.org>, Satya Tangirala <satyat@google.com> Subject: [RFC PATCH v4 4/4] scsi: ufs-qcom: add Inline Crypto Engine support Date: Thu, 30 Apr 2020 21:51:11 -0700 Message-Id: <20200501045111.665881-5-ebiggers@kernel.org> In-Reply-To: <20200501045111.665881-1-ebiggers@kernel.org> References: <20200501045111.665881-1-ebiggers@kernel.org> MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Sender: linux-arm-msm-owner@vger.kernel.org Precedence: bulk
Series	None \| expand [RFC,v4,2/4] arm64: dts: sdm845: add Inline Crypto Engine registers and clock [RFC,v4,4/4] scsi: ufs-qcom: add Inline Crypto Engine support

diff --git a/MAINTAINERS b/MAINTAINERS index 26f281d9f32a4a..cab5fe76784592 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2236,7 +2236,7 @@ F: drivers/pci/controller/dwc/pcie-qcom.c F: drivers/phy/qualcomm/ F: drivers/power/*/msm* F: drivers/reset/reset-qcom-* -F: drivers/scsi/ufs/ufs-qcom.* +F: drivers/scsi/ufs/ufs-qcom* F: drivers/spi/spi-geni-qcom.c F: drivers/spi/spi-qcom-qspi.c F: drivers/spi/spi-qup.c diff --git a/drivers/scsi/ufs/Kconfig b/drivers/scsi/ufs/Kconfig index 5ed3f209f88100..c1a94d99e161ee 100644 --- a/drivers/scsi/ufs/Kconfig +++ b/drivers/scsi/ufs/Kconfig @@ -99,6 +99,7 @@ config SCSI_UFS_DWC_TC_PLATFORM config SCSI_UFS_QCOM tristate "QCOM specific hooks to UFS controller platform driver" depends on SCSI_UFSHCD_PLATFORM && ARCH_QCOM + select QCOM_SCM select RESET_CONTROLLER help This selects the QCOM specific additions to UFSHCD platform driver. diff --git a/drivers/scsi/ufs/Makefile b/drivers/scsi/ufs/Makefile index 197e178f44bce3..13fda1b697b2a2 100644 --- a/drivers/scsi/ufs/Makefile +++ b/drivers/scsi/ufs/Makefile @@ -3,7 +3,9 @@ obj-$(CONFIG_SCSI_UFS_DWC_TC_PCI) += tc-dwc-g210-pci.o ufshcd-dwc.o tc-dwc-g210.o obj-$(CONFIG_SCSI_UFS_DWC_TC_PLATFORM) += tc-dwc-g210-pltfrm.o ufshcd-dwc.o tc-dwc-g210.o obj-$(CONFIG_SCSI_UFS_CDNS_PLATFORM) += cdns-pltfrm.o -obj-$(CONFIG_SCSI_UFS_QCOM) += ufs-qcom.o +obj-$(CONFIG_SCSI_UFS_QCOM) += ufs_qcom.o +ufs_qcom-y += ufs-qcom.o +ufs_qcom-$(CONFIG_SCSI_UFS_CRYPTO) += ufs-qcom-ice.o obj-$(CONFIG_SCSI_UFSHCD) += ufshcd-core.o ufshcd-core-y += ufshcd.o ufs-sysfs.o ufshcd-core-$(CONFIG_SCSI_UFS_BSG) += ufs_bsg.o diff --git a/drivers/scsi/ufs/ufs-qcom-ice.c b/drivers/scsi/ufs/ufs-qcom-ice.c new file mode 100644 index 00000000000000..9e837fdcb0ac2b --- /dev/null +++ b/drivers/scsi/ufs/ufs-qcom-ice.c @@ -0,0 +1,245 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Qualcomm ICE (Inline Crypto Engine) support. + * + * Copyright (c) 2014-2019, The Linux Foundation. All rights reserved. + * Copyright (c) 2019 Google LLC + */ + +#include <linux/platform_device.h> +#include <linux/qcom_scm.h> + +#include "ufshcd-crypto.h" +#include "ufs-qcom.h" + +#define AES_256_XTS_KEY_SIZE 64 + +/* QCOM ICE registers */ + +#define QCOM_ICE_REG_CONTROL 0x0000 +#define QCOM_ICE_REG_RESET 0x0004 +#define QCOM_ICE_REG_VERSION 0x0008 +#define QCOM_ICE_REG_FUSE_SETTING 0x0010 +#define QCOM_ICE_REG_PARAMETERS_1 0x0014 +#define QCOM_ICE_REG_PARAMETERS_2 0x0018 +#define QCOM_ICE_REG_PARAMETERS_3 0x001C +#define QCOM_ICE_REG_PARAMETERS_4 0x0020 +#define QCOM_ICE_REG_PARAMETERS_5 0x0024 + +/* QCOM ICE v3.X only */ +#define QCOM_ICE_GENERAL_ERR_STTS 0x0040 +#define QCOM_ICE_INVALID_CCFG_ERR_STTS 0x0030 +#define QCOM_ICE_GENERAL_ERR_MASK 0x0044 + +/* QCOM ICE v2.X only */ +#define QCOM_ICE_REG_NON_SEC_IRQ_STTS 0x0040 +#define QCOM_ICE_REG_NON_SEC_IRQ_MASK 0x0044 + +#define QCOM_ICE_REG_NON_SEC_IRQ_CLR 0x0048 +#define QCOM_ICE_REG_STREAM1_ERROR_SYNDROME1 0x0050 +#define QCOM_ICE_REG_STREAM1_ERROR_SYNDROME2 0x0054 +#define QCOM_ICE_REG_STREAM2_ERROR_SYNDROME1 0x0058 +#define QCOM_ICE_REG_STREAM2_ERROR_SYNDROME2 0x005C +#define QCOM_ICE_REG_STREAM1_BIST_ERROR_VEC 0x0060 +#define QCOM_ICE_REG_STREAM2_BIST_ERROR_VEC 0x0064 +#define QCOM_ICE_REG_STREAM1_BIST_FINISH_VEC 0x0068 +#define QCOM_ICE_REG_STREAM2_BIST_FINISH_VEC 0x006C +#define QCOM_ICE_REG_BIST_STATUS 0x0070 +#define QCOM_ICE_REG_BYPASS_STATUS 0x0074 +#define QCOM_ICE_REG_ADVANCED_CONTROL 0x1000 +#define QCOM_ICE_REG_ENDIAN_SWAP 0x1004 +#define QCOM_ICE_REG_TEST_BUS_CONTROL 0x1010 +#define QCOM_ICE_REG_TEST_BUS_REG 0x1014 + +/* BIST ("built-in self-test"?) status flags */ +#define QCOM_ICE_BIST_STATUS_MASK 0xF0000000 + +#define QCOM_ICE_FUSE_SETTING_MASK 0x1 +#define QCOM_ICE_FORCE_HW_KEY0_SETTING_MASK 0x2 +#define QCOM_ICE_FORCE_HW_KEY1_SETTING_MASK 0x4 + +#define qcom_ice_writel(host, val, reg) \ + writel((val), (host)->ice_mmio + (reg)) +#define qcom_ice_readl(host, reg) \ + readl((host)->ice_mmio + (reg)) + +static bool qcom_ice_supported(struct ufs_qcom_host *host) +{ + struct device *dev = host->hba->dev; + u32 regval = qcom_ice_readl(host, QCOM_ICE_REG_VERSION); + int major = regval >> 24; + int minor = (regval >> 16) & 0xFF; + int step = regval & 0xFFFF; + + /* For now this driver only supports ICE version 3. */ + if (major != 3) { + dev_warn(dev, "Unsupported ICE version: v%d.%d.%d\n", + major, minor, step); + return false; + } + + dev_info(dev, "Found QC Inline Crypto Engine (ICE) v%d.%d.%d\n", + major, minor, step); + + /* If fuses are blown, ICE might not work in the standard way. */ + regval = qcom_ice_readl(host, QCOM_ICE_REG_FUSE_SETTING); + if (regval & (QCOM_ICE_FUSE_SETTING_MASK | + QCOM_ICE_FORCE_HW_KEY0_SETTING_MASK | + QCOM_ICE_FORCE_HW_KEY1_SETTING_MASK)) { + dev_warn(dev, "Fuses are blown; ICE is unusable!\n"); + return false; + } + return true; +} + +int ufs_qcom_ice_init(struct ufs_qcom_host *host) +{ + struct ufs_hba *hba = host->hba; + struct device *dev = hba->dev; + struct platform_device *pdev = to_platform_device(dev); + struct resource *res; + int err; + + if (!(ufshcd_readl(hba, REG_CONTROLLER_CAPABILITIES) & + MASK_CRYPTO_SUPPORT)) + return 0; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 2); + if (!res) { + dev_warn(dev, "ICE registers not found\n"); + goto disable; + } + + if (!qcom_scm_ice_available()) { + dev_warn(dev, "ICE SCM interface not found\n"); + goto disable; + } + + host->ice_mmio = devm_ioremap_resource(dev, res); + if (IS_ERR(host->ice_mmio)) { + err = PTR_ERR(host->ice_mmio); + dev_err(dev, "Failed to map ICE registers; err=%d\n", err); + return err; + } + + if (!qcom_ice_supported(host)) + goto disable; + + return 0; + +disable: + dev_warn(dev, "Disabling inline encryption support\n"); + hba->caps &= ~UFSHCD_CAP_CRYPTO; + return 0; +} + +static void qcom_ice_low_power_mode_enable(struct ufs_qcom_host *host) +{ + u32 regval; + + regval = qcom_ice_readl(host, QCOM_ICE_REG_ADVANCED_CONTROL); + /* + * Enable low power mode sequence + * [0]-0, [1]-0, [2]-0, [3]-E, [4]-0, [5]-0, [6]-0, [7]-0 + */ + regval |= 0x7000; + qcom_ice_writel(host, regval, QCOM_ICE_REG_ADVANCED_CONTROL); +} + +static void qcom_ice_optimization_enable(struct ufs_qcom_host *host) +{ + u32 regval; + + /* ICE Optimizations Enable Sequence */ + regval = qcom_ice_readl(host, QCOM_ICE_REG_ADVANCED_CONTROL); + regval |= 0xD807100; + /* ICE HPG requires delay before writing */ + udelay(5); + qcom_ice_writel(host, regval, QCOM_ICE_REG_ADVANCED_CONTROL); + udelay(5); +} + +int ufs_qcom_ice_enable(struct ufs_qcom_host *host) +{ + if (!(host->hba->caps & UFSHCD_CAP_CRYPTO)) + return 0; + qcom_ice_low_power_mode_enable(host); + qcom_ice_optimization_enable(host); + return ufs_qcom_ice_resume(host); +} + +/* Poll until all BIST bits are reset */ +static int qcom_ice_wait_bist_status(struct ufs_qcom_host *host) +{ + int count; + u32 reg; + + for (count = 0; count < 100; count++) { + reg = qcom_ice_readl(host, QCOM_ICE_REG_BIST_STATUS); + if (!(reg & QCOM_ICE_BIST_STATUS_MASK)) + break; + udelay(50); + } + if (reg) + return -ETIMEDOUT; + return 0; +} + +int ufs_qcom_ice_resume(struct ufs_qcom_host *host) +{ + int err; + + if (!(host->hba->caps & UFSHCD_CAP_CRYPTO)) + return 0; + + err = qcom_ice_wait_bist_status(host); + if (err) { + dev_err(host->hba->dev, "BIST status error (%d)\n", err); + return err; + } + return 0; +} + +/* + * Program a key into a QC ICE keyslot, or evict a keyslot. QC ICE requires + * vendor-specific SCM calls for this; it doesn't support the standard way. + */ +int ufs_qcom_ice_program_key(struct ufs_hba *hba, + const union ufs_crypto_cfg_entry *cfg, int slot) +{ + union ufs_crypto_cap_entry cap; + union { + u8 bytes[AES_256_XTS_KEY_SIZE]; + u32 words[AES_256_XTS_KEY_SIZE / sizeof(u32)]; + } key; + int i; + int err; + + if (!(cfg->config_enable & UFS_CRYPTO_CONFIGURATION_ENABLE)) + return qcom_scm_ice_invalidate_key(slot); + + /* Only AES-256-XTS has been tested so far. */ + cap = hba->crypto_cap_array[cfg->crypto_cap_idx]; + if (cap.algorithm_id != UFS_CRYPTO_ALG_AES_XTS || + cap.key_size != UFS_CRYPTO_KEY_SIZE_256) { + dev_err_ratelimited(hba->dev, + "Unhandled crypto capability; algorithm_id=%d, key_size=%d\n", + cap.algorithm_id, cap.key_size); + return -EINVAL; + } + + memcpy(key.bytes, cfg->crypto_key, AES_256_XTS_KEY_SIZE); + + /* + * The SCM call byte-swaps the 32-bit words of the key. So we have to + * do the same, in order for the final key be correct. + */ + for (i = 0; i < ARRAY_SIZE(key.words); i++) + __cpu_to_be32s(&key.words[i]); + + err = qcom_scm_ice_set_key(slot, key.bytes, AES_256_XTS_KEY_SIZE, + QCOM_SCM_ICE_CIPHER_AES_256_XTS, + cfg->data_unit_size); + memzero_explicit(&key, sizeof(key)); + return err; +} diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c index 19aa5c44e0da6f..37c4070c9007ef 100644 --- a/drivers/scsi/ufs/ufs-qcom.c +++ b/drivers/scsi/ufs/ufs-qcom.c @@ -365,7 +365,7 @@ static int ufs_qcom_hce_enable_notify(struct ufs_hba *hba, /* check if UFS PHY moved from DISABLED to HIBERN8 */ err = ufs_qcom_check_hibern8(hba); ufs_qcom_enable_hw_clk_gating(hba); - + ufs_qcom_ice_enable(host); break; default: dev_err(hba->dev, "%s: invalid status %d\n", __func__, status); @@ -614,6 +614,10 @@ static int ufs_qcom_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op) return err; } + err = ufs_qcom_ice_resume(host); + if (err) + return err; + hba->is_sys_suspended = false; return 0; } @@ -1071,6 +1075,7 @@ static void ufs_qcom_set_caps(struct ufs_hba *hba) hba->caps |= UFSHCD_CAP_CLK_GATING | UFSHCD_CAP_HIBERN8_WITH_CLK_GATING; hba->caps |= UFSHCD_CAP_CLK_SCALING; hba->caps |= UFSHCD_CAP_AUTO_BKOPS_SUSPEND; + hba->caps |= UFSHCD_CAP_CRYPTO; if (host->hw_ver.major >= 0x2) { host->caps = UFS_QCOM_CAP_QUNIPRO | @@ -1297,6 +1302,10 @@ static int ufs_qcom_init(struct ufs_hba *hba) ufs_qcom_set_caps(hba); ufs_qcom_advertise_quirks(hba); + err = ufs_qcom_ice_init(host); + if (err) + goto out_variant_clear; + ufs_qcom_set_bus_vote(hba, true); ufs_qcom_setup_clocks(hba, true, POST_CHANGE); @@ -1735,6 +1744,7 @@ static const struct ufs_hba_variant_ops ufs_hba_qcom_vops = { .dbg_register_dump = ufs_qcom_dump_dbg_regs, .device_reset = ufs_qcom_device_reset, .config_scaling_param = ufs_qcom_config_scaling_param, + .program_key = ufs_qcom_ice_program_key, }; /** diff --git a/drivers/scsi/ufs/ufs-qcom.h b/drivers/scsi/ufs/ufs-qcom.h index 2d95e7cc71874e..97247d17e258ad 100644 --- a/drivers/scsi/ufs/ufs-qcom.h +++ b/drivers/scsi/ufs/ufs-qcom.h @@ -227,6 +227,9 @@ struct ufs_qcom_host { void __iomem *dev_ref_clk_ctrl_mmio; bool is_dev_ref_clk_enabled; struct ufs_hw_version hw_ver; +#ifdef CONFIG_SCSI_UFS_CRYPTO + void __iomem *ice_mmio; +#endif u32 dev_ref_clk_en_mask; @@ -264,4 +267,28 @@ static inline bool ufs_qcom_cap_qunipro(struct ufs_qcom_host *host) return false; } +/* ufs-qcom-ice.c */ + +#ifdef CONFIG_SCSI_UFS_CRYPTO +int ufs_qcom_ice_init(struct ufs_qcom_host *host); +int ufs_qcom_ice_enable(struct ufs_qcom_host *host); +int ufs_qcom_ice_resume(struct ufs_qcom_host *host); +int ufs_qcom_ice_program_key(struct ufs_hba *hba, + const union ufs_crypto_cfg_entry *cfg, int slot); +#else +static inline int ufs_qcom_ice_init(struct ufs_qcom_host *host) +{ + return 0; +} +static inline int ufs_qcom_ice_enable(struct ufs_qcom_host *host) +{ + return 0; +} +static inline int ufs_qcom_ice_resume(struct ufs_qcom_host *host) +{ + return 0; +} +#define ufs_qcom_ice_program_key NULL +#endif /* !CONFIG_SCSI_UFS_CRYPTO */ + #endif /* UFS_QCOM_H_ */

[RFC,v4,4/4] scsi: ufs-qcom: add Inline Crypto Engine support

Commit Message

Comments

Patch